Fouling control in a submerged membrane‐bioreactor by the membrane surface modification

To improve the antifouling characteristics, polypropylene microporous membranes (PPHFMMs) were surface‐modified by the sequential photoinduced graft polymerization of acrylic acid and acrylamide. The grafting density and the grafting chain length, which played important roles in the antifouling characteristics, were controlled in the first and the second step, respectively. The ATR/FTIR results clearly indicated the successful modification on the membrane surface. The static water contact angle of the modified membrane reduced obviously with the increase of the grafting chain length. The contact angle of the acrylic acid modified membranes was lower than that of the acrylamide modified membrane with similar grafting chain length. The grafting chain length increased with the increase of UV irradiation time and monomer concentration. The grafting chain length of poly(acrylic acid) (PAAc) was lower than that of the polyacrylamide (PAAm) under the same polymerization conditions. Pure water flux for the modified membranes increased with the increase of grafting chain length, and had maximums. The antifouling characteristics of the modified membranes in a submerged membrane‐bioreactor (SMBR) were evaluated. The modified membranes showed better filtration performances in the SMBR than the unmodified membrane, and the acrylic acid grafted membrane presented better antifouling characteristics than acrylamide modified membranes. The results demonstrated that the surface carboxyl‐containing membranes were better than the surface amido‐containing membranes. The results of Pearson correlations demonstrated that the PAAc modified membranes with longer grafting chain length had higher flux recoveries, while the PAAm modified membranes with longer grafting chain length had lower flux recoveries. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Fabrication and characterization of maleic anhydride grafted polypropylene membranes with high antifouling properties

In this study, maleic anhydride grafted polypropylene microporous flat‐sheet membranes were prepared via a thermally induced phase separation method with a mixture of dibutyl phthalate and dioctyl phthalate as a diluent. The effects of the polymer composition and coagulation bath temperature on the morphology and performance of the fabricated membranes were investigated. The hydrophilicity results of the membranes demonstrated that membrane modification reduced the water contact angle by about 45°, whereas the pure water flux was enhanced about four times. The antifouling behavior of the fabricated membranes was also investigated in a membrane bioreactor. The results show that the pure water flux, membrane pore size, and porosity decreased, whereas the antifouling performance was improved with increasing polymer concentration and decreasing bath temperature. Finally, the results reveal that the removal efficiency of contaminates was independent on the membrane characterization and was done exclusively through biological removal. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43857.     

Low protein fouling polypropylene membrane prepared by photoinduced reversible addition‐fragmentation chain transfer polymerization

In this study, 2‐hydroxyethyl methacrylate and N‐isopropyl acrylamide was block grafted onto the polypropylene macroporous membrane surface by photo‐induced reversible addition‐fragmentation chain transfer (RAFT) radical polymerization with benzyl dithiobenzoate as the RAFT agent. The degree of grafting of poly(2‐hydroxyethyl methacrylate) on the membrane surface increased with UV irradiation time and decreased with the chain transfer agent concentration increasing. The poly(2‐hydroxyethyl methacrylate)‐ grafted membranes were used as macro chain transfer agent for the further block graft copolymerization of N‐isopropyl acrylamide in the presence of free radical initiator. The degree of grafting of poly(N‐isopropyl acrylamide) increased with reaction time. Furthermore, the poly(2‐hydroxyethyl methacrylate)‐ grafted membrane with a degree of grafting of 0.48% (wt) showed the highest relative pure water flux and the best antifouling characteristics of protein dispersion. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Improving the hydrophilicity of polyethersulfone membrane by the combination of grafting technology and reverse thermally induced phase separation method

In this work, surface grafting modification technology was combined with reverse thermally induced phase separation (RTIPS) method in order to improve the structure and permanent hydrophilicity of polyethersulfone (PES) membranes. Acrylic solution with different concentrations was grafted on the surface of PES membranes while grafting temperature and grafting time were also varied. The modified PES membranes were characterized in all aspects. Attenuated total reflectance Fourier transform-infrared confirmed successful modification of the PES membrane by grafting acrylic acid. Scanning electron microscopy revealed that homogeneous porous top surface as well as spongy-like cross-section structure appeared in the membrane by RTIPS procedure. Moreover, porosity was affected by changes of acrylic acid concentration, grafting temperature, and grafting time. Atomic force microscopy showed that grafting acrylic acid gave a reduction in roughness of PES membrane. Combined with the decreased values of contact angle, the hydrophilicity and antifouling performance of the PES membrane were improved. The pure water flux and BSA rejection rate of the grafted PES membranes were remarkably improved for pure PES membrane and attained a maximum, which was 1,646.24 L/(m²h) and 94.5%, respectively. The long-term test demonstrated that grafting membranes exhibited outstanding elevated water flux recovery ratio (>85%).     

Effect of cellulose acetate/cellulose triacetate ratio on reverse osmosis blend membrane performance

Surface functionalization and modification including the grafting process are effective approaches to improve and enhance the reverse osmosis (RO) membrane performance. This work is aimed to synthesize grafted/crosslinked cellulose acetate (CA)/cellulose triacetate (CTA) blend RO membranes using N-isopropylacrylamide (N-IPAAm) as a monomer and N,N-methylene bisacrylamide (MBAAm) as a crosslinker. The morphology of these membranes was analyzed by scanning electron microscopy and their surface roughness was characterized by atomic force microscopy. The performance of these membranes was evaluated through measuring two major parameters of salt rejection and water flux using RO unit at variable operating pressures. It was noted that the surface average roughness obviously decreased from 148 nm for the pure CA/CTA blend membrane with 2.5% CTA to 110 nm and 87 nm for the grafted N-IPAAm and grafted/crosslinked N-IPAAM/MBAAm/CA/CTA-RO membranes, respectively. Moreover, the contact angle decreased from 51.98° to 47.6° and 43.8° after the grafting and crosslinking process. The salt rejection of the grafted CA/CTA-RO membrane by 0.1% N-IPAAm produced the highest value of 98.12% and the water flux was 3.29 L/m²h at 10 bar.     

Antifouling microfiltration membranes prepared from poly(vinylidene fluoride)‐graft‐Poly(N‐ vinyl pyrrolidone) powders synthesized via pre‐irradiation induced graft polymerization

Poly(vinylidene fluoride) (PVDF) powders were grafted with N‐vinyl pyrrolidone using the pre‐irradiation induced graft polymerization technique. The effects of reaction time, absorbed dose, and monomer concentration on the degree of grafting were investigated, and the grafted PVDF powders were characterized by Fourier transform infrared spectroscopy, thermogravimetric analysis, and differential scanning calorimetry. The grafted PVDF powders were also cast into microfiltration (MF) membranes via the phase‐inversion method. The contact angle and water uptake were measured. The membrane morphology was studied by scanning electron microscopy, and the water filtration properties of the membranes were tested. The antifouling properties were determined through measurements of the recovery percentage of pure water flux after the MF membranes were fouled with bovine serum albumin solution. The results confirmed that the existence of poly(N‐vinyl pyrrolidone) (PVP) graft chains improved the hydrophilicity and antifouling properties of the MF membranes cast from PVDF‐g‐PVP powders. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Tris(hydroxymethyl)aminomethane polyamide thin‐film‐composite antifouling reverse osmosis membrane

For the applications of reverse osmosis (RO) process, membrane fouling caused by organic molecule adsorption is still a serious problem which significantly decreases membrane lifespan and increases operation costs. In this present article, we report the thin film composite (TFC) RO membrane functionalized with tris(hydroxymethyl)aminomethane (THAM) using one‐step method for improved antifouling property. The results of surface characterization indicated that THAM was successfully grafted onto the active layer of membrane by covalent linkage. Mult‐hydroxyl‐layer was generated and remained steadily on TFC membrane surface after modification. The contact angle decreased from 75.9 ± 3.0° to 46.9 ± 2.3°, which showed a distinct improvement of membrane surface hydrophilicity after modification. The grafted THAM improved water flux by 28.3%, while salt rejection was almost unchanged in membrane property tests. The modified membranes presented preferable antifouling property to foulants of bovine serum albumin, sodium alginate, and dodecyl trimethyl ammonium bromide than that of pristine membranes during dynamic fouling experiments. The method in this study provided an effective way to improve antifouling property of the polyamide thin‐film‐composite RO membrane. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45891.     

Surface structure of low density polyethylene films grafted with acrylic acid using corona discharge

Chemical composition, morphology, and crystalline structure of low density polyethylene (LDPE) films surface grafted with acrylic acid (AA) using corona discharge were studied by attenuated total reflection infrared (ATR-IR), electron spectroscopy for chemical analysis (ESCA), scanning electron microscopy (SEM), differential scanning calorimetry (DSC), and wide angle X-ray diffraction (WAXD) techniques. The grafted film surface is covered with grafted chains. After grafting for 3.0 h in 20% aqueous solution of AA, the depth of the grafted layer is more than 10 nm. A grain structure was observed on the grafted surfaces which was probably caused by the isolated dispersion of active sites generated by corona discharge, and these active sites initiated the graft copolymerization. However, surfaces of grafted films were smoother than that of ungrafted ones. DSC curves of grafted films show a small peak at about 100°C due to vaporization of adsorbed water. The longer the graft copolymerization time, i.e. the higher the graft degree of AA on LDPE, the higher the amount of adsorbed water. The position of each peak in WAXD patterns, crystal axial length, crystal plane distance and crystal grain size remain almost unchanged during the graft copolymerization time of 2.0 h. However, when the graft copolymerization time reaches 3.0 h, twin peaks at about 21.4° and 22.0° are observed, indicating that a different crystal form is formed at longer copolymerization time, i.e. at a higher graft degree.     

Smart PTFE Membrane with Hydrophilicity and pH Sensitivity through MAA-grafting

In this article, the microporous membrane of stretched polytetrafluoroethylene (S-PTFE) film was modified through grafting hydrophilic methacrylic acid (MAA). SEM image showed that the grafted poly(methacrylic acid) (PMAA) covered uniquely on regular nanofiber-frame in S-PTFE. The surface contact angle of the membrane minishes rapidly with the increase of grafting ratio and falls down to the minimum point at 57° when the grafting ratio is about 4.7%. The water flux of the PTFE-g-PMAA membrane is very sensitive to pH values. At lower pH, the larger water flux was obtained. This contribution indicate the possibility of adjustable water flux by pH.     

PAN ultrafiltration membranes grafted with natural amino acids for improving antifouling property

In this report, antifouling polyacrylonitrile (PAN) ultrafiltration membranes were prepared from blends of PAN/polyglycidyl methacrylate (PGMA) via phase inversion method followed by the grafting of natural amino acids through epoxy ring-opening reaction. The grafted PAN membranes possessed highly stable hydrophilic surfaces as a result of the grafting of amino acids, which was adequately demonstrated in attenuated total reflectance–Fourier transform infrared spectroscopy (ATR/FTIR), X-ray photoelectron spectroscopy (XPS), and contact angle measurements. The results of tensile strength and scanning electron microscopy (SEM) images further proved that the surface modification had little effect on their mechanical properties, surface, and cross-sectional morphologies. Meanwhile, remarkable resistance against bovine serum albumin (BSA) and lysozyme (Lyz) fouling was observed for the neutral amino acid-based PAN membranes due to the formation of zwitterionic hydration layer on the membrane surface, while PAN membranes grafted with charged amino acids were able to prohibit the approach of like charged proteins with reduced deposition and provide the driving force for oppositely charged protein adsorption. Furthermore, the ultrafiltration and antifouling performance of PAN membranes were investigated by BSA filtration experiments. Compared with the pristine PAN membrane, all the modified PAN membranes exhibited higher pure water flux, better flux recovery ratio, lower rejection, less total permeation resistance, and preferable stability, having potential applications in protein separation and purification.     

Hydrophilic Modification of PVDF Microfiltration Membrane with Poly (Ethylene Glycol) Dimethacrylate through Surface Polymerization

The hydrophilic modification of poly (vinylidene fluoride) (PVDF) membrane with poly (ethylene glycol) dimethacrylate (PEGDMA) through grafting reaction for antifouling was reported. The influence of PEGDMA content, reaction temperature and time, on the structure, morphology, antifouling, and hydrophilicity of PVDF-g-PEGDMA membrane has been investigated. The PEGDMA monomers that were grafted on the surface of PVDF microfiltration membrane were confirmed by Attenuation total reflectance-Fourier transform infrared spectroscopy (ATR-FTIR) and X-ray photoelectron spectroscopy (XPS), and morphology study conducted by SEM revealed the changes before and after modification. The protein adsorption, filtration performance, water content, and dynamic contact angle were used to characterize the antifouling and hydrophilicity of the modified PVDF membranes. Compared with the pristine PVDF membrane, the bovine serum albumin (BSA) adsorption on the PVDF-g-PEGDMA membrane decreased about 80%, and the water contact angle of the membrane dropped to 0°. Besides, the experimental results revealed no significant differences between the membrane samples with respect to pore size.     

紫外光诱导接枝共聚制备离子识别性聚丙烯微孔膜

以聚丙烯微孔膜(MPPM)为支撑,采用物理包埋和紫外光诱导共价键合组合法固定光引发剂,再通过紫外光诱导接枝共聚制得离子印迹复合膜。考察了制备条件对离子印迹聚合物接枝量的影响,并用扫描电子显微镜(SEM)-能量色散X射线光谱仪(EDX)对复合膜表面及截面离子印迹聚合物的分布进行了分析。静态水接触角和纯水通量实验结果显示,离子印迹复合膜具有良好的表面亲水性和渗透性,纯水通量可达(2 077±77)L/(m2.h)。再生性研究表明,离子印迹复合膜具有良好的再生性能,10次吸附-脱吸附循环后,膜对Pb(Ⅱ)的吸附量和选择性系数分别能维持在90%和80%以上。     

Polyacrylonitrile‐g‐poly(vinyl alcohol) membranes for the pervaporation separation of dimethyl formamide and water mixtures

Poly(vinyl alcohol) as well as its grafted copolymer membranes with polyacrylonitrile (PAN‐g‐PVA) were prepared and used to separate water and dimethyl formamide mixtures by the pervaporation technique. The three following membranes were prepared: (1) pure PVA; (2) 46% grafted PAN‐g‐PVA; and (3) 93% grafted PAN‐g‐PVA. Pervaporation separation experiments were carried out at 25°C for the feed mixture containing 10 to 90% water. By use of the transport data, permeation flux, separation selectivity, swelling index, and diffusion coefficients have been calculated. By increasing the grafting of the membrane, flux decreased, whereas separation selectivity increased slightly over that of pure PVA membrane. Arrhenius activation parameters for transport processes were calculated for 10 mass % water containing feed mixture by using flux and diffusion data obtained at 25, 35, and 45°C. Transport parameters were discussed in terms of sorption‐diffusion principles. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 91: 4091–4097, 2004     

Surface modification of polyamide reverses osmosis membrane by phosphonic acid group with improved performance

A facial method for preparing reverse osmosis polyamide (PA) membranes of excellent antifouling and separation performance was developed via covalently grafting phosphonic acid on membrane surface. First, a pristine PA layer was synthesized by interfacial polymerization between m-phenylenediamine and trimesoyl chloride. Then, a second interfacial reaction was implemented between ethylenediamine and the residual acryl chloride on the pristine PA layer, generating an active layer enriched by primary amine. Finally, the amine-rich surface treated by formaldehyde and phosphorous acid to produce a membrane surface modified by phosphonic acid groups. Surface characterization by attenuated total reflectance infrared, X-ray photoelectron spectroscopy and zeta-potential measurements illustrated the presence of phosphonic acid group. The lowest contact angle of modified membrane was 26°, demonstrating the membrane possessed an outstandingly wettable surface. The optimal separation performance was 88 L m⁻² h⁻¹ of water flux and 99.4% of salt rejection under 1.55 MPa. In addition, bovine serum albumin was used as organic foulant to measure the antifouling property of membranes. The result of dynamic fouling experiments indicated that the modified membrane exhibited better antifouling (of which the irreversible fouling degree was 7.1%) compared with commercial membrane BW30 (of which the irreversible fouling degree was 13.5%). © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 46931.     

Facile surface modification of PVDF microfiltration membrane by strong physical adsorption of amphiphilic copolymers

To endow the surface of poly(vinylidene fluoride) (PVDF) microfiltration (MF) membranes with hydrophilicity and antifouling property, physical adsorption of amphiphilic random copolymers of poly(ethylene glycol) methacrylate (PEGMA) and poly(methyl methacrylate) (PMMA) (P(PEGMA‐r‐MMA)) onto the PVDF membrane was performed. Scanning electron microscopy (SEM) images showed that the adsorption process had no influence on the membrane structure. Operation parameters including adsorption time, polymer concentration, and composition were explored in detail through X‐ray photoelectron spectroscopy (XPS), static water contact angle (CA), and water flux measurements. The results demonstrated that P(PEGMA‐r‐MMA) copolymers adsorbed successfully onto the membrane surface, and hydrophilicity of the PVDF MF membrane was greatly enhanced. The antifouling performance and adsorption stability were also characterized, respectively. It was notable that PVDF MF membranes modified by facile physical adsorption of P(PEGMA₅₈‐r‐MMA₃₃) even showed higher water flux and better antifouling property than the commercial hydrophilic PVDF MF membranes. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 3112–3121, 2013     

Poly(arylene sulfide sulfone) hybrid ultrafiltration membrane with TiO2‐g‐PAA nanoparticles: Preparation and antifouling performance

Poly(arylene sulfide sulfone) (PASS) is a kind of newly developed polymeric membrane material which has excellent mechanical strength, thermal stability, and solvent resistance. And, it would be a potential material for high temperature ultrafiltration and organic solvent filtration. In this article, PASS hybrid ultrafiltration membrane with improved antifouling property was prepared by mixing TiO₂ nanoparticles which were grafted with polyacrylic acid (PAA). These membranes were prepared by a phase inversion technique and their separation performance and antifouling property of the prepared membranes were investigated in detail by SEM, FTIR, EDS, contact angle goniometry, filtration experiments of water, and BSA solution. The results shown that the TiO₂‐g‐PAA nanoparticles dispersed well in membrane matrix, the hydrophilicity of the membranes prepared within TiO₂‐g‐PAA nanoparticles have been improved and these membranes exhibited excellent water flux and antifouling performance in separation than that of the pure PASS membranes and PASS membranes with TiO₂ nanoparticles. More specifically, among membrane sample M0, M1.5, and MP1.5, MP1.5 which contained 1.5 wt% TiO₂‐g‐PAA exhibited the highest water permeation (190.4 L/m² h at 100 kPa), flux recovery ratio, and the lowest BSA adsorption amount. POLYM. ENG. SCI., 55:2829–2837, 2015. © 2015 Society of Plastics Engineers     

Plasma‐induced grafting of hydroxyethyl methacrylate (HEMA) onto chitosan membranes by a swelling method

Hydroxyethyl methacrylate (HEMA) was grafted onto chitosan membranes by plasma‐graft polymerization. Effects of monomer concentration, plasma power and plasma time on the amount of grafting were investigated. The results showed that there were two processes: grafting polymerization and etching of the membrane. The surface of the grafted membrane was evaluated by FTIR. Scanning electron microscopy indicated that the surface morphology of the grafted membrane could be adjusted through plasma power. Water contact angles of the chitosan surface decreased from 78.2° to 45.4° while the amount of grafting increased from 0 to 12.2%, indicating improved hydrophilicity of the membrane surface. Permeation coefficients through the original membrane, the membrane treated at 55 W for 15 min, and the membrane treated at 55 W for 30 min for creatinine were 9.12 × 10^?7, 10.6 × 10^?7 and 8.57 × 10^?7 cm² s^?1, respectively. Thermogravimetry and mechanical testing showed that there were no significant changes on the bulk property of chitosan membrane after modification. © 2003 Society of Chemical Industry     

紫外接枝丙烯酸对PVDF膜表面改性的研究

以二苯甲酮为光引发剂,通过紫外辐照将亲水性单体丙烯酸接枝于聚偏氟乙烯(PVDF)膜的表面。考察了光引发剂浓度和辐照时间对接枝率的影响,并利用衰减全反射光谱和扫描电子显微镜对接枝后PVDF膜表面的化学组成和微观形貌进行了表征。结果表明:随着光引发剂浓度的增大,丙烯酸的接枝率先增大后减小。通过纯水接触角和吸水率研究了接枝后的PVDF膜的亲水性,发现接枝后的PVDF膜的亲水性得到明显改善。     

High-density polyethylene membranes embedded with carboxylated and polyethylene glycol-grafted nanodiamond to be used in membrane bioreactors

In this work, neat and modified nanodiamond (ND) particles were embedded into high-density polyethylene (HDPE) membranes to improve hydrophilicity and antifouling properties. The membranes were prepared via thermally induced phase separation (TIPS) method and used for pharmaceutical wastewater treatment in membrane bioreactors (MBR) system. To prevent the agglomeration of ND, it was modified using two methods: thermal carboxylation (ND-COOH) and grafting with polyethylene glycol (ND-PEG). Membranes with different concentration of ND-COOH and ND-PEG nanoparticles ranging from 0.00 to 1.00 wt % were prepared and characterized using a set of analyses including water contact angle, pure water flux, tensile strength, differential scanning calorimeter, field emission scanning electron microscopy, and energy dispersive X-ray spectroscopy. It was found that the optimum contents of ND-COOH and ND-PEG nanoparticles were 0.50 wt % and 0.75 wt %, respectively. The interfacial interaction between nanoparticles and HDPE matrix was studied based on Pukanzsky model. To examine the performance of membranes, critical flux, filtration experiment in the MBR, and fouling analysis of membranes were carried out. The results showed that among the fabricated membranes, 0.75 wt % HDPE/ND-PEG membrane had the highest water flux and the best antifouling properties. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47914.     

Microwave plasma‐initiated grafting of acrylic acid on Celgard 2500 membrane to prepare alkaline battery separators—Characteristics of process and product

A process of plasma‐initiated grafting of acrylic acid on commercial porous polypropylene membrane was studied. The influence of parameters of the plasma (power, gas pressure, time plasma‐sample distance, sample arrangement) and grafting (solvent composition, monomer concentration, time, inhibitor presence) on the degree of grafting, amount of homopolymer produced and surface electrical resistance was determined. A degree of grafting up to 18 mmol/g was obtained, which resulted in sample resistance as low as 30 mΩ cm². The molecular weight of AAc homopolymer that can be assumed as equal to the MW of grafted chains, ranged from 25,000 to 50,000,000 da. SEM and water permeability measurements show that grafting causes filling of the pores, which, however, does not stop K⁺ ions from penetrating the membrane. The performance of nickel‐cadmium cells with acrylic acid grafted membranes as separator is also presented. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010