Syntheses and characterization of poly(butylene terephthalate) copolyesters modified with p‐acetoxybenzoic acid

Poly(butylene terephthalate) (PBT) copolyesters modified with seven compositions of p‐acetoxybenzoic acid (PABA) ranging from 10 to 70 mol % were prepared. The X‐ray diffraction patterns, the polarizing microscopy behaviors, and thermal analysis showed that the modified PBT contained more PABA homopolymer units (PABA–PABA) than PBT–PABA units in the copolyesters. On increasing PABA mole percenage, PBT crystallinity decreased and thermal stability increased. It was found that although the PBT copolyesters did not exhibit a clear liquid crystalline texture like the copolyester of poly(ethylene terephthalate) modified with PABA did, the PBT copolyester containing 70 mol % of PABA exhibited the typical shear thinning behavior of a liquid crystalline polymer. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 1085–1095, 2001     

Crystallization kinetics of poly(1,4‐butylene‐co‐ethylene terephthalate)

The crystallization kinetics of poly(butylene terephthalate) (PBT), poly(ethylene terephthalate) (PET), and their copolymers poly(1,4‐butylene‐co‐ethylene terephthalate) (PBET) containing 70/30, 65/35 and 60/40 molar ratios of 1,4‐butanediol/ethylene glycol were investigated using differential scanning calorimetry (DSC) at crystallization temperatures (T_c) which were 35–90 °C below equilibrium melting temperature . Although these copolymers contain both monomers in high proportion, DSC data revealed for copolymer crystallization behaviour. The reason for such copolymers being able to crystallize could be due to the similar chemical structures of 1,4‐butanediol and ethylene glycol. DSC results for isothermal crystallization revealed that random copolymers had a lower degree of crystallinity and lower crystallite growth rate than those of homopolymers. DSC heating scans, after completion of isothermal crystallization, showed triple melting endotherms for all these polyesters, similar to those of other polymers as reported in the literature. The crystallization isotherms followed the Avrami equation with an exponent n of 2–2.5 for PET and 2.5–3.0 for PBT and PBETs. Analyses of the Lauritzen–Hoffman equation for DSC isothermal crystallization data revealed that PBT and PET had higher growth rate constant G_o, and nucleation constant K_g than those of PBET copolymers. © 2001 Society of Chemical Industry     

Influence of high density polyethylene‐g‐maleic anhydride on compatibility and properties of poly(butylene terephthalate)/high density polyethylene blends

Poly(butylene terephthalate)/high density polyethylene (PBT/HDPE) blends and PBT/HDPE‐grafted maleic anhydride (PBT/HDPE‐g‐MAH) blends were prepared by the reactive extrusion approach, and the effect of blend compositions on the morphologies and properties of PBT/HDPE blends and PBT/HDPE‐g‐MAH blends was studied in detail. The results showed that flexural strength, tensile strength, and notched impact strength of PBT/HDPE blends decreased with the addition of HDPE, and flexural strength and tensile strength of PBT/HDPE‐g‐MAH blends decreased, while the notched impact strength of PBT/HDPE‐g‐MAH increased with the addition of HDPE‐g‐MAH. Compared with PBT/HDPE blends, the dimension of the dispersed phase particles in PBT/HDPE‐g‐MAH blends was decreased and the interfacial adhesion was increased. On the other hand, the effects of HDPE and HDPE‐g‐MAH contents on the crystalline and the rheological properties of the blends were also investigated. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 6081–6087, 2006     

Hydrolytic degradation of poly(1,4‐butylene terephthalate‐co‐tetramethylene oxalate) copolymer

Experimentally synthesized poly(1,4‐butylene terephthalate‐co‐tetramethylene oxalate) (PBT–PTMO) monofilaments were evaluated for hydrolytic stability in salt water (SW) and distilled water (DW) at temperature below and above glass transition temperature (T_g), along with commercially available poly(hexamethylene adipamide) (NY), poly(ethylene terephthalate) (PET), and polypropylene (PP) monofilaments. There was no decrease in mechanical properties in case of NY, PET, and PP in either DW or SW below their T_g. The breaking strength, ultimate elongation, and thermal shrinkage of the PBT–PTMO, however, decreased as the ageing time increased. Total strength loss occurred after approximately 300 days at 25°C in either DW and SW. This can be attributed to the chain scission that occurs in the PBT–PTMO copolymer chain. The poor hydrolytic stability of the PBT–PTMO may be attributed to the higher moisture regain. The salinity of water did not have a significant effect on the breaking strength loss of the materials. The mode of hydrolytic degradation of aged PBT–PTMO polymer was confirmed by the increasing generation of the acid carbonyl and hydroxyl groups with concomitant increasing consumption of ester groups, regardless of ageing conditions. Above T_g, the hydrolytic rate constant (k^′_H, day⁻¹) of the PBT–PTMO, estimated by the rate of formation of acid carbonyl groups, is greater at a higher ageing temperature. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 921–936, 1999     

Synthesis and characterization of poly[(butylene succinate)‐co‐(butylene terephthalate)]‐b‐poly(tetramethylene glycol) segmented block copolymer

Polyester‐polyether segmented block copolymers of poly[(butylene succinate)‐co‐poly(butylene terephthalate)] (PBS–PBT) and poly(tetramethylene glycol) (PTMG) (M_n = 2000) with various compositions were synthesized. PBT content in the PBS was adjusted to ca. 5 mol %. Their thermal and mechanical properties were investigated. In the case of copolymer, the melting point of the PBS–PBT control was 107.8°C, and the melting point of the copolymer containing 70 wt % of PTMG was 70.1°C. Crystallinity of soft segment was 5 ∼ 17%, and that of hard segment was 42 ∼ 59%. The breaking stress of the PBS–PTMG control was 47 MPa but it decreased with increasing PTMG content. In the case of copolymer containing 70 wt % of PTMG, breaking stress was 36 MPa. Contrary to the decreasing breaking stress, breaking strain increased from 300% for PBS–PBT control to 900% for a copolymer containing 70 wt % of PTMG. The shape recovery ratios of the copolymer containing 70 wt % PTMG were almost twice of those of copolymers containing 40 wt % PTMG. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 79: 2067–2075, 2001     

The effect of pH on the hydrolytic degradation of poly(ε‐caprolactone)‐block‐poly(ethylene glycol) copolymers

The in‐vitro hydrolytic behavior of diblock copolymer films consisting of poly(ε‐caprolactone) (PCL) and poly(ethylene glycol) (PEG) was studied at pH 7.4 and pH 9.5 at 37°C. The degradation of these films was characterized at various time intervals by mass loss measurements, GPC, ¹H‐NMR, DSC, FTIR, XRD, and SEM. A faster rate of degradation took place at pH 9.5 than at pH 7.4. Analysis of the molecular weight profile during the course of degradation revealed that random chain scission of the ester bonds in PCL predominates at the initial induction phase of polymer degradation. There was also an insignificant mass loss of the films observed. Mass spectroscopy was used to determine the nature of the water soluble products of degradation. At pH 7.4, a variety of oligomers with different numbers of repeating units were present whereas the harsher degradation conditions at pH 9.5 resulted in the formation of dimers. From the results, it can be proposed that a more complete understanding of the degradation behavior of the PCL‐b‐PEG copolymer can be monitored using a combination of physiological and accelerated hydrolytic degradation conditions. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Morphology of poly(styrene‐block‐dimethylsiloxane) copolymer films

The morphologies of poly(styrene‐block‐di‐methylsiloxane) (PS‐b‐PDMS) copolymer thin films were analyzed via atomic force microscopy and transition electron microscopy (TEM). The asymmetric copolymer thin films spin‐cast from toluene onto mica presented meshlike structures, which were different from the spherical structures from TEM measurements. The annealing temperature affected the surface morphology of the PS‐b‐PDMS copolymer thin films; the polydimethylsiloxane (PDMS) phases at the surface were increased when the annealing temperature was higher than the PDMS glass‐transition temperature. The morphologies of the PS‐b‐PDMS copolymer thin films were different from solvent to solvent; for thin films spin‐cast from toluene, the polystyrene (PS) phase appeared as pits in the PDMS matrix, whereas the thin films spin‐cast from cyclohexane solutions exhibited an islandlike structure and small, separated PS phases as protrusions over the macroscopically flat surface. The microphase structure of the PS‐b‐PDMS copolymer thin films was also strongly influenced by the different substrates; for an asymmetric block copolymer thin film, the PDMS and PS phases on a silicon substrate presented a lamellar structure parallel to the surface at intervals. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 1010–1018, 2007     

Rheological and thermal properties of blends of modified poly(ethylene terephthalate) with p‐acetoxybenzoic acid and poly(butylene terephthalate)

Blending of thermotropic liquid crystalline polyesters (LCPs) with conventional polymers could result in materials that can be used as an alternative for short fiber‐reinforced thermoplastic composites, because of their low melt viscosity as well as their inherent high stiffness and strength, high use temperature, and excellent chemical resistance and low coefficient of expansion. In most of the blends was used LCP of 40 mol % of poly(ethylene terephthalate) (PET) and 60 mol % of p‐acetoxybenzoic acid (PABA). In this work, blends of several copolyesters having various PABA compositions from 10 to 70 mol % and poly(butylene terephthalate) (PBT) were prepared and their rheological and thermal properties were investigated. For convenience, the copolyesters were designated as PETA‐x, where x is the mol % of PABA. It was found that PET‐60 and PET‐70 copolyesters decreased the melt viscosity of PBT in the blends and those PBT/PETA‐60 and PBT/PETA‐70 blends showed different melt viscosity behaviors with the change in shear rate, while blends of PBT and PET‐x having less than 50 mol % of PABA exhibited totally different rheological behaviors. The blends of PBT with PETA‐50, PETA‐60, and PETA‐70 showed the morphology of multiple layers of fibers. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 1797–1806, 1999     

Synthesis and characterization of copolymers based on poly(butylene terephthalate) and ethylene oxide‐poly(dimethylsiloxane)‐ethylene oxide

A series of thermoplastic elastomers based on ethylene oxide‐poly(dimethylsiloxane)‐ethylene oxide (EO‐PDMS‐EO), as the soft segment, and poly(butylene terephthalate) (PBT), as the hard segment, were synthesized by catalyzed two‐step, melt transesterification reaction of dimethyl terephthalate (DMT) with 1,4‐butanediol (BD) and α,ω‐dihydroxy‐(EO‐PDMS‐EO). Copolymers with a content of hard PBT segments between 40 and 90 mass % and a constant length of the soft EO‐PDMS‐EO segments were prepared. The siloxane prepolymer with hydrophilic terminal EO units was used to improve the miscibility between the polar comonomers, DMT and BD, and the nonpolar PDMS. The molecular structure and composition of the copolymers were determined by ¹H‐NMR spectroscopy, whereas the effectiveness of the incorporation of α,ω‐dihydroxy‐(EO‐PDMS‐EO) into the copolymer chains was verified by chloroform extraction. The effects of the structure and composition of the copolymers on the melting temperatures and the degree of crystallinity, as well as on the thermal degradation stability and some rheological properties, were studied. It was demonstrated that the degree of crystallinity, the melting and crystallization temperatures of the copolymers increased with increasing mass fraction of the PBT segments. The thermal stability of the copolymers was lower than that of PBT homopolymer, because of the presence of thermoliable ether bonds in the soft segments. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

The hydrolytic stability of glass fiber reinforced poly(butylene terephthalate), poly(ethylene terephthalate) and polycarbonate

The hydrolytic stability of glass fiber reinforced poly(butylene terephthalate) (PBT), poly(ethylene terephthalate) (PET) and polycarbonate (PC) was studied. The activation energies in kcal/mole for hydrolysis are 26 for PBT and 23 for PET. Both PBT and PET contain 30 percent glass fiber reinforcement. The hydrolysis rates for a series of experimental PC's containing 10, 30 and 40 percent glass were obtained from GPC data. These increase with glass concentration but are lower than that of the unreinforced PC. Melt flow rate changes are a good measure of the hydrolytic degradation of PET. However, in the time scale of these experiments, the tensile properties of glass reinforced PBT and PC do not correlate well with M?_w changes, unlike unreinforced PBT and PC polymers. Consequently, to compare these three glass fiber reinforced polymers, estimates of failure time must be based on changes in tensile strength rather than melt flow rate.     

Influence of the degree of grafting on the morphology and mechanical properties of blends of poly(butylene terephthalate) and glycidyl methacrylate grafted poly(ethylene‐co‐propylene) (EPR)

Poly(ethylene‐co‐propylene) (EPR) was functionalized to varying degrees with glycidyl methacrylate (GMA) by melt grafting processes. The EPR‐graft‐GMA elastomers were used to toughen poly(butylene terephthalate) (PBT). Results showed that the grafting degree strongly influenced the morphology and mechanical properties of PBT/EPR‐graft‐GMA blends. Compatibilization reactions between the carboxyl and/or hydroxyl of PBT and epoxy groups of EPR‐graft‐GMA induced smaller dispersed phase sizes and uniform dispersed phase distributions. However, higher degrees of grafting (>1.3) and dispersed phase contents (>10 wt%) led to higher viscosities and severe crosslinking reactions in PBT/EPR‐graft‐GMA blends, resulting in larger dispersed domains of PBT blends. Consistent with the change in morphology, the impact strength of the PBT blends increased with the increase in EPR‐graft‐GMA degrees of grafting for the same dispersion phase content when the degree of grafting was below 1.8. However, PBT/EPR‐graft‐GMA1.8 displayed much lower impact strength in the ductile region than a comparable PBT/EPR‐graft‐GMA1.3 blend (1.3 indicates degree of grafting). Morphology and mechanical results showed that EPR‐graft‐GMA 1.3 was more suitable in improving the toughness of PBT. SEM results showed that the shear yielding properties of the PBT matrix and cavitation of rubber particles were major toughening mechanisms. Copyright © 2006 Society of Chemical Industry     

Synthesis and thermal characterization of random poly(butylene terephthalate‐co‐2‐methyl‐ethylene terephthalate) copolyesters

Poly(butylene terephthalate‐co‐2‐methyl‐ethylene terephthalate) (PBT/MET) was synthesized by incorporating 1,2‐propandiol(1,2‐PDO) into PBT chains. The molar composition and chemical structure of PBT/MET copolyesters were confirmed by means of FT‐IR and ¹H‐NMR. To investigate the effect of 1,2‐PDO on the thermal properties of PBT/MET copolyesters, the copolymerizations were carried out by varying various contents of MET units, and the prepared materials were evaluated by differential scanning calorimetry and thermogravimetric analysis. Results suggested that with the increase of the content of 1,2‐PDO, the amount of crystallinity and the melting temperature decline, while the glass transition temperature increases and the copolyesters become more transparent and brittle with respect to PBT homopolymer. In addition, the T_g‐composition and T_m‐composition data are well subjected to the Wood equation and Flory's equation, respectively. All these copolyesters are found to consist of the general trend displayed by copolymers reported elsewhere. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Characterization and biodegradability of poly(butylene adipate‐co‐succinate)/poly(butylene terephthalate) copolyester

Characterization of poly(butylene adipate‐co‐succinate) (PBAS)/poly(butylene terephthalate) (PBT) copolyesters resulting from the intermolecular ester‐exchange reaction between molten PBAS and PBT have been analyzed using ¹H‐NMR spectroscopy, differential scanning calorimetry, wide‐angle X‐ray diffraction, and total organic carbon lab analyzer. Using the assignment of proton resonance due to homogeneous and heterogeneous dyads, the average block lengths were investigated over the entire range of copolymer composition. A decrease in melting temperature was observed with the increase of a terephthalate unit in the composition. The result of X‐ray diffraction curve matches well with that of average block length and thermal property. When a rich component is crystallized, the poor component is excluded completely in a crystal formation. The biodegradability in copolyesters also depended on the terephthalate unit in the composition and average block length of the aromatic unit. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 72: 593–608, 1999     

Thermal and crystallization characteristics of poly(ethylene terephthalate) with poly(oxybenzoate‐p‐trimethylene terephthalate) copolymer

Poly(ethylene terephthalate) (PET) was blended with two different poly(oxybenzoate‐p‐trimethylene terephthalate) copolymers, designated T28 and T64, with the level of copolymer varying from 1 to 15 wt %. All samples were prepared by solution blending in a 60/40 (by weight) phenol/tetrachloroethane solvent at 50°C. The crystallization behavior of the samples was studied by DSC. The results indicate that both T28 and T64 accelerated the crystallization rate of PET in a manner similar to that of a nucleating agent. The acceleration of PET crystallization rate was most pronounced in the PET/T64 blends with a maximum level at 5 wt % of T64. The melting temperatures for the blends are comparable to that of pure PET. The observed changes in crystallization behavior are explained by the effect of the physical state of the copolyester during PET crystallization as well as the amount of copolymer in the blends. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 1599–1606, 2002     

Toughening effects of poly(butylene terephthalate) with blocked isocyanate‐functionalized poly(ethylene octene)

BACKGROUND: Blocked isocyanate‐functionalized polyolefins have great potential for use in semicrystalline polymer blends to obtain toughened polymers. In this study, poly(butylene terephthalate) (PBT) was blended with allyl N‐[2‐methyl‐4‐(2‐oxohexahydroazepine‐1‐carboxamido)phenyl] carbamate‐functionalized poly(ethylene octene) (POE‐g‐AMPC). RESULTS: New peaks at 2272 and 1720 cm^?1, corresponding to the stretching vibrations of NCO and the carbonyl of NH? CO? N, respectively, in AMPC, appeared in the infrared spectrum of POE‐g‐AMPC. Both rheological and X‐ray photoelectron spectroscopy results indicated a new copolymer was formed in the reactive blends. Compared to uncompatibilized PBT/POE blends, smaller dispersed particle sizes with narrower distribution were found in the compatibilized PBT/POE‐g‐AMPC blends. There was a marked increase in impact strength by about 10‐fold over that of PBT/POE blends with the same rubber content and almost 30‐fold higher than that of pure PBT when the POE‐g‐AMPC content was 25 wt%. CONCLUSION: The blocked isocyanate‐functionalized POE is an effective toughener for semicrystalline polymers. Super‐toughened PBT blends can be obtained when the POE‐g‐AMPC content is equal to or more than 15 wt%. Copyright © 2009 Society of Chemical Industry     

Copolymers based on poly(butylene terephthalate) and polycaprolactone‐block‐polydimethylsiloxane‐block‐polycaprolactone

A series of novel thermoplastic elastomers, based on poly(butylene terephthalate) (PBT) and polycaprolactone‐block‐polydimethylsiloxane‐block‐polycaprolactone (PCL‐PDMS‐PCL), with various mass fractions, were synthesized through melt polycondensation. In the synthesis of the poly(ester‐siloxane)s, the PCL blocks served as a compatibilizer for the non‐polar PDMS blocks and the polar comonomers dimethyl terephthalate and 1,4‐butanediol. The introduction of PCL‐PDMS‐PCL soft segments resulted in an improvement of the miscibility of the reaction mixture and therefore in higher molecular weight polymers. The content of hard PBT segments in the polymer chains was varied from 10 to 80 mass%. The degree of crystallinity of the poly(ester‐siloxane)s was determined using differential scanning calorimetry and wide‐angle X‐ray scattering. The introduction of PCL‐PDMS‐PCL soft segments into the polymer main chains reduced the crystallinity of the hard segments and altered related properties such as melting temperature and storage modulus, and also modified the surface properties. The thermal stability of the poly(ester‐siloxane)s was higher than that of the PBT homopolymer. The inclusion of the siloxane prepolymer with terminal PCL into the macromolecular chains increased the molecular weight of the copolymers, the homogeneity of the samples in terms of composition and structure and the thermal stability. It also resulted in mechanical properties which could be tailored. Copyright © 2010 Society of Chemical Industry     

Thermal decomposition kinetics of thermotropic poly(oxybenzoate‐co‐trimethylene terephthalate)

A new kind of thermotropic liquid crystalline, poly(oxybenzoate‐co‐trimethylene terephthalate), was prepared from p‐hydroxybenzoic acid (B) and poly(trimethylene terephthalate) (PTT or T) by melting polycondensation. The monomer ratio of B to T is 60:40. The dynamic thermogravimetric kinetics of the copolymer B/T (60:40) and PTT in nitrogen were analyzed by four single heating rate techniques and two multiple heating rate techniques. The effects of the heating rate and the calculating technique on the thermostable and degradation kinetic parameters of the B/T copolymer and PTT are systematically discussed. The four single heating rate techniques used in this work include Friedman, Freeman‐Carroll, Chang, and the second Kissinger techniques, whereas the two multiple heating rate techniques are the first Kissinger and Flynn‐Wall techniques. Additionally, the isothermal thermogravimetric kinetics of B/T (60:40) in nitrogen were investigated by the Flynn technique. The activation energy, the order, and the frequency factor of the degradation reaction for B/T (60:40) copolymer are determined to be 185 kJ/mol, 1.8, and 7.14 × 10¹³ min⁻¹, respectively. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 78: 2025–2036, 2000     

Degradation of poly(D,L‐lactic acid)‐b‐poly(ethylene glycol)‐b‐poly(D,L‐lactic acid) copolymer by electron beam radiation

This article investigates the effects of electron beam (EB) radiation on poly(D ,L ‐lactic acid)‐b‐poly (ethylene glycol) copolymer (PLA‐b‐PEG‐b‐PLA). The copolymer films were EB irradiated at doses from 0 to 100 kGy. The degradation of these films was studied by measuring the changes in their molecular weight, mechanical and thermal properties. The dominant effect of EB radiation on PLA‐b‐PEG‐b‐PLA is chain‐scission. With increasing irradiation dose, recombination reactions or partial crosslinking may occur in addition to chain scission. The degree of chain scission G_s and crosslinking G_x of sample are calculated to be 0.213 and 0.043, respectively. A linear relationship is also established between the decreases in molecular weight with increasing irradiation dose. Elongation at break of the irradiated sample decreases significantly, whereas its tensile strength decreases slightly. The glass transition temperature (T_g) is basically invariant as a function of irradiation dose. Thermogravimetric analysis shows that its thermal stability decreases with increasing dose. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Biodegradability of poly(ethylene terephthalate) copolymers with poly(ethylene glycol)s and poly(tetramethylene glycol)

Poly(ethylene terephthalate) copolymers were prepared by melt polycondensation of dimethyl terephthalate and excess ethylene glycol with 10–40mol% (in feed) of poly(ethylene glycol) (E) and poly(tetramethylene glycol) (B), with molecular weight (MW) of E and B 200–7500 and 1000, respectively. The reduced specific viscosity of copolymers increased with increasing MW and content of polyglycol comonomer. The temperature of melting (T_m), cold crystallization and glass transition (T_g) decreased with the copolymerization. T_m depression of copolymers suggested that the E series copolymers are the block type at higher content of the comonomer. T_g was decreased below room temperature by the copolymerization, which affected the crystallinity and the density of copolymer films. Water absorption increased with increasing content of comonomer, and the increase was much higher for E1000 series films than B1000 series films. The biodegradability was estimated by weight loss of copolymer films in buffer solution with and without a lipase at 37°C. The weight loss was enhanced a little by the presence of a lipase, and increased abruptly at higher comonomer content, which was correlated to the water absorption and the concentration of ester linkages between PET and PEG segments. The weight loss of B series films was much lower than that of E series films. The abrupt increase of the weight loss by alkaline hydrolysis is almost consistent with that by biodegradation.