Atom transfer radical polymerization of acrylonitrile

Iron(II) chloride coordinated by succinic acid was first used as the catalyst in 2‐chloropropionitrile‐initiated atom transfer radical polymerization (ATRP) of acrylonitrile. N,N‐dimethylformamide was used as a solvent to improve the solubility of the ligand. An iron(II) chloride to succinic acid ratio of 0.5 not only gives the best control of molecular weight and its distribution but also provides rather rapid reaction rate. Effects of solvent on polymerization of acrylonitrile were also investigated. The induction period is shorter in N,N‐dimethylformamide than in propylene carbonate and toluene and the rate of the polymerization in N,N‐dimethylformamide is fastest. The molecular weight of polyacrylonitrile agrees reasonably well with the theoretical molecular weight of N,N‐dimethylformamide. The rate of polymerization increases and the induction period becomes shorter with increasing polymerization temperature, and the apparent activation energy was calculated to be 56.5 kJ mol^?1. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 1050–1054, 2006     

Atom transfer radical polymerization of styrene using a copper catalyst with a pseudohalogen anion

Atom transfer radical polymerization has been a very useful method in the recent advances in controlled radical polymerization. It needs an activated alkyl halide as an initiator and a copper halide as a catalyst. This investigation reports the successful application of copper thiocyanate, a catalyst with a pseudohalide anion, in the presence of different ligands such as N,N,N=,N″,N?,N?‐hexamethyltriethylenetetramine (HMTETA), pentyl‐2‐pyridylmethaneimine, and substituted bipyridine in the atom transfer radical polymerization of styrene. Among the three ligands used, HMTETA was found to be very efficient. The polymers were characterized with ¹³C‐NMR, matrix‐assisted laser desorption/ionization time‐of‐flight mass spectrometry, and gel permeation chromatography analysis. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 1418–1426, 2005     

Atom transfer radical polymerization of lauryl methacrylate

The atom transfer radical polymerization (ATRP) of lauryl methacrylate (LMA) with an ethyl 2‐bromobutyrate/CuCl/N,N,N′,N″,N″‐pentamethyldiethylenetriamine initiation system was successfully carried out in toluene, and poly(lauryl methacrylate) with a low polydispersity (1.2 < weight‐average molecular weight/number‐average molecular weight < 1.5) was obtained. Plots of ln ([M])₀/([M]) versus time and plots of the molecular weight versus conversion showed a linear dependence, indicating a constant number of propagating species throughout the polymerization. The rate of polymerization was 0.56‐order with respect to the concentration of the initiator and 1.30‐order with respect to the concentration of the Cu(I) catalyst. In addition, the effect of the solvent on the polymerization was investigated, and the thermodynamic data and activation parameters for the solution ATRP of LMA were reported. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 1117–1125, 2003     

Atom transfer radical polymerization of methyl methacrylate initiated with a macroinitiator of poly(vinyl acetate)

Well‐defined poly(vinyl acetate‐b‐methyl methacrylate) block copolymers were successfully synthesized by the atom transfer radical polymerization (ATRP) of methyl methacrylate (MMA) in p‐xylene with CuBr as a catalyst, 2,2′‐bipyridine as a ligand, and trichloromethyl‐end‐grouped poly(vinyl acetate) (PVAc–CCl₃) as a macroinitiator that was prepared via the telomerization of vinyl acetate with chloroform as a telogen. The block copolymers were characterized with gel permeation chromatography, Fourier transform infrared, and ¹H‐NMR. The effects of the solvent and temperature on ATRP of MMA were studied. The control over a large range of molecular weights was investigated with a high [MMA]/[PVAc–CCl₃] ratio for potential industry applications. In addition, the mechanism of the polymerization was discussed. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 1089–1094, 2006     

Atom transfer radical bulk polymerization of methyl methacrylate under microwave irradiation

Microwave irradiation (MI) was applied to the atom transfer radical bulk polymerization of methyl methacrylate. The influence of the amount of the refluxing solvent used for controlling the polymerization temperature, irradiation power, irradiation time, and initiator concentration on the conversion, molecular weight, and molecular weight distribution of the polymers was studied with a benzyl chloride/cuprous chloride/2,2′‐bipyridyl initiation system and compared with the corresponding conventional heating (CH) process. In comparison with CH, the results can be summarized as follows. The polymerization rate for reaching 70% conversion increased 2.6–5.1 times under an irradiation power of 270–630 W. The apparent increasing rate constant was much larger than that with CH and increased with the irradiation power. MI produced a higher polymerization rate and conversion even if the concentration of the initiation system was very low (initial monomer concentration/initial initiator concentration = 200:0.33 mol/mol) and the polydispersity index (DI) was narrower; however, CH yielded almost no polymers. MI promoted the activities of the catalyst and monomer, and its initiation efficiency was higher than that with CH and increased with the irradiation power. MI obviously played an important role in promoting the polymerization rate of atom transfer radical polymerization (ATRP). MI reduced the concentration of the initiation system and perhaps made ATRP controlled (cf. uncontrolled ATRP with CH); at the same time, it made the DI values of the polymers narrower. In comparison with the initiation efficiencies found with benzyl bromide and 2,2′‐azobisisobutyronitrile used as initiators, the initiation efficiency with p‐toluene sulfonyl chloride used as an initiator was higher; moreover, DI was much narrower (1.17), and the polymerization rate was greater. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 1787–1793, 2003     

甲基丙烯酸2,2,2-三氟乙酯的原子转移自由基聚合

以α-溴代丙酸乙酯(EPN-B)/CuCl/ 联二吡啶(bpy)作为引发/催化体系、环己酮为溶剂,对甲基丙烯酸2,2,2-三氟乙酯(TFEMA)进行原子转移自由基聚合(ATRP),研究了TFEMA的反应动力学,并考察了引发/催化体系、引发剂EPN-B用量、配位剂bpy用量及单体配比对聚合反应的影响.结果表明,采用EPN-B/CuCl/bpy引发/催化体系对TFEMA进行ATRP,可得到窄分子量分布的聚甲基丙烯酸2,2,2-三氟乙酯(PTFEMA),在实验范围内,聚合速率对单体浓度呈一级动力学关系,该反应过程具有活性聚合特征;随着引发剂EPN-B和配位剂bpy用量的增加,聚合速率加快,当EPN-B相对摩尔用量为0.5,1.0,2.0时,其相应的表观链增长速率常数分别为3.143×10~(-4),3.478×10~(-4),4.435×10~(-4)s~(-1);增大[TFEMA]/[EPN-B](摩尔比),聚合速率明显降低,但无论[TFEMA]/[EPN-B]高与低,聚合物的分布指数均为1.15～1.23.     

Reverse atom‐transfer radical polymerization of acrylonitrile catalyzed by FeCl3/iminodiacetic acid

FeCl₃ coordinated by iminodiacetic acid (IMA) was Changed used for the first time as the catalyst in azobisisobutyronitrile‐initiated reverse atom‐transfer radical polymerization (ATRP) of acrylonitrile (AN). An FeCl₃ to IMA ratio of 1:2 not only gave the best control of molecular weight and its distribution but also provided a rather rapid reaction rate. The effects of solvents on the polymerization of AN were also investigated. The rate of the polymerization in N,N‐dimethylformamide (DMF) was faster than in propylene carbonate or toluene. The molecular weight of polyacrylonitrile agreed reasonably well with the theoretical molecular weight in DMF. The rate of polymerization increased with increasing polymerization temperature and the apparent activation energy was calculated to be 54.8 kJ mol⁻¹. The reverse ATRP of AN did not show obvious living characteristics with CuCl₂ instead of FeCl₃. Copyright © 2005 Society of Chemical Industry     

Controlled radical copolymerization of vinyl acetate and dibutyl maleate by iodine transfer radical polymerization

Iodine transfer radical homo‐ and copolymerization of vinyl acetate (VAc) with dibutyl maleate (DBM) were carried out in the presence of ethyl iodoacetate (EtIAc) and 2,2′‐azobis(isobutyronitrile) (AIBN) as chain transfer agent and initiator, respectively, at 60 °C. Molecular weight and its distribution and (co)polymer structure (i.e. copolymer composition and chain end groups) were analysed using gel permeation chromatography and ¹H NMR spectroscopy, respectively. Homo‐ and copolymerization reactions proceed via a controlled characteristic with predetermined molecular weight and relatively narrow molecular weight distribution. The presence of DBM in the reaction mixture decreases the consumption rate of EtIAc as well as the polymerization rate. This is attributed to the effect of DBM on the transfer constant to the EtIAc and probably on the iodine exchange rate constant between the growing chains. The effect of the concentration of AIBN, EtIAc and overall monomers on the conversion, molecular weight and its distribution was studied. Simultaneously high conversion and molecular weight with a relatively narrow molecular weight distribution can be achieved only when equimolar and intermediate concentration of EtIAc and AIBN is used in the reaction mixture. End‐group analysis by ¹H NMR reveals that iodinated VAc end groups in the (co)polymer chains are unstable, resulting in aldehyde end groups. Thermogravimetric analysis shows that the thermal stability of the VAc‐based polymer increases on incorporating DBM units into the copolymer chains. © 2013 Society of Chemical Industry     

Atom transfer radical suspension polymerization of methyl methacrylate catalyzed by CuCl/bpy

Atom transfer radical suspension polymerization (suspension ATRP) of methyl methacrylate (MMA) was carried out using 1-chloro-1-phenylethane (1-PECl) as initiator, copper chloride/bipyridine (CuCl/bpy) as catalyst. The polymerization was accomplished with a mechanical agitator under the protection of nitrogen atmosphere. Apart from the dispersing agent (1% PVA), NaCl was also used in the water phase to decrease the diffusion of CuCl/bpy to water and the influence of the concentration of NaCl was investigated. Subsequently, the kinetic behavior of the suspension ATRP of MMA at different temperatures was studied. At 90 and 95 °C, the polymerization showed first order with respect to monomer concentration until high conversion. The molecular weight (M_n) of the polymer increased with monomer conversion. However, at lower temperatures, different levels of autoacceleration was observed. The polymerization deviated from first order with respect to monomer concentration when the conversion was up to some degree. The lower the temperature was, the more the deviation displayed. On comparison with bulk ATRP of MMA, the rate of suspension ATRP was much faster.     

Reverse atom transfer radical polymerization of acrylonitrile under microwave irradiation

Reverse atom transfer radical polymerization was first used to successfully synthesize polyacrylonitrile under microwave irradiation. FeCl₃, coordinated by isophthalic acid, was used as the catalyst, and 2,2′‐azobisisoheptonitrilewas used as the initiator. N,N‐Dimethylformamide was used as the solvent to improve the solubility of the ligand. Under the same experimental conditions, the apparent rate constant under microwave irradiation was higher than that under conventional heating. The polymerization not only showed the best control of the molecular weight and its distribution but also provided a rather rapid reaction rate with the [acrylonitrile]/[2,2′‐azobisisoheptonitrile]/[FeCl₃]/[isophthalic acid] ratio of 300 : 1 : 1 : 2. The polymers obtained were used as macroinitiators to initiate the chain extension and successfully synthesize acrylonitrile polymers with a molecular weight higher than 50,000 and a narrow polydispersity as low as 1.30. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Reverse atom transfer radical polymerization of acrylonitrile

FeCl₃ coordinated by succinic acid was used as the catalyst for the first time in azobisisobutyronitrile‐initiated reverse atom transfer radical polymerization of acrylonitrile (AN). N,N‐dimethylformamide (DMF) was used as a solvent to improve the solubility of the ligand. A FeCl₃ to succinic acid ratio of 0.5 not only gives the best control of molecular weight and its distribution but also provides rather rapid reaction rate. Effects of different solvents on polymerization of AN were also investigated. The rate of the polymerization in DMF is faster than that in propylene carbonate and toluene. The molecular weight of polyacrylonitrile agrees reasonably well with the theoretical molecular weight in DMF. The rate of polymerization increases with increasing the polymerization temperature, and the apparent activation energy was calculated to be 64.8 kJ mol^?1. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 32–36, 2006     

Reverse atom transfer radical polymerization of methyl methacrylate in different solvents

The reverse atom transfer radical polymerization of methyl methacrylate was investigated in different solvents: xylene, N,N‐dimethylformamide, and pyridine. The polymerizations were uncontrolled, using 2,2′‐bipyridine as a ligand in xylene and pyridine because the catalyst (CuBr₂/2,2′‐bipyridine complex) had poor solubility in the xylene system. In the pyridine system, the solubility of the catalyst increased, but the solvent could complex with CuBr₂, which influenced the control of the polymerization. In the N,N‐dimethylformamide system, the catalyst could be dissolved in the solvent completely, but the ? N(CH₃)₂ group in N,N‐dimethylformamide could also complex with CuBr₂, so the polymerization could not be well controlled. The ligand of 4,4′‐di(5‐nonyl)‐2,2′‐bipyridine was also investigated in xylene; the introduction of the ? CH(C₄H₉)₂ group enabled the CuBr₂/4,4′‐di(5‐nonyl)‐2,2′‐bipyridine complex to easily dissolve in xylene, and the polymerizations were well controlled. The number‐average molecular weight increased linearly with the monomer conversion from 4280 to 14,700. During the whole polymerization, the polydispersities were quite low (1.07–1.10). © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Atom transfer radical copolymerization of glycidyl methacrylate and methyl methacrylate

Glycidyl methacrylate (GMA) and methyl methacrylate (MMA) copolymers were synthesized by atom transfer radical polymerization (ATRP). The effect of different molar fractions of GMA, ranging from 0.28 to 1.0, on the polymer polydispersity index (weight‐average molecular weight/number‐average molecular weight) as the indicator of a controlled process was investigated at 70°C, with ethyl 2‐bromoisobutyrate as an initiator and 4,4′‐dinonyl‐2,2′‐bipyridyne (dNbpy)/CuBr as a catalyst system in anisole. The monomer reactivity ratios (r values) were obtained by the application of the conventional linearization Fineman–Ross method (r_GMA = 1.24 ± 0.02 and r_MMA = 0.85 ± 0.03) and by the Mayo–Lewis method (r_GMA = 1.19 ± 0.04 and r_MMA = 0.86 ± 0.03). The molecular weights and polydispersities of the copolymers exhibited a linear increase with GMA content. The copolymer compositions were determined by ¹H‐NMR and showed a domination of syndiotactic structures. The glass‐transition temperatures (T_g) of the copolymers analyzed by differential scanning calorimetry (DSC) decreased in the range 105–65°C with increasing GMA units. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

High‐molecular‐weight polyacrylonitrile by atom transfer radical polymerization

A single‐pot atom transfer radical polymerization was used for the first time to successfully synthesize polyacrylonitrile with a molecular weight higher than 80,000 and a narrow polydispersity as low as 1.18. This was achieved with CuBr/isophthalic acid as the catalyst, 2‐bromopropionitrile as the initiator, and N,N‐dimethylformamide as the solvent. The effects of the solvent on the polymerization of acrylonitrile were also investigated. The induction period was shorter in N,N‐dimethylformamide than in propylene carbonate and toluene, and the rate of the polymerization in N,N‐dimethylformamide was fastest. The molecular weight of polyacrylonitrile agreed reasonably well with the theoretical molecular weight in N,N‐dimethylformamide. When chlorine was used in either the initiator or the catalyst, the rate of polymerization showed a trend of decreasing, and the molecular weight deviated from the theoretical predication significantly. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 3372–3376, 2006     

原子转移自由基乳液聚合研究进展

原子转移自由基聚合(ATRP)作为一种可控/活性聚合方法,可对聚合物结构进行精确控制;乳液聚合以水作为分散介质,具有经济、环保等特点。因此,乳液ATRP结合了两者的优点,具有工业化生产的潜力。首先分析了影响乳液ATRP的各种因素,然后综述了正向ATRP、RATRP(反向ATRP)、SR&NI ATRP(正向/反向同时进行的ATRP)和AGET ATRP(电子转移活化剂ATRP)等机制及研究进展,最后对乳液ATRP的发展方向进行了展望。     

Atom transfer radical polymerizations of methyl methacrylate and styrene with an iniferter reagent as the initiator

Three novel iniferter reagents were synthesized and used as initiators for the polymerizations of methyl methacrylate (MMA) and styrene (St) in the presence of copper(I) bromide and N,N,N′,N″,N″‐pentamethyldiethylenetriamine at 90 and 115°C, respectively. All the polymerizations were well controlled, with a linear increase in the number‐average molecular weights during increased monomer conversions and relatively narrow molecular weight distributions (weight‐average molecular weight/number‐average molecular weight ≤ 1.36) throughout the polymerization processes. The polymerization rate of MMA was faster in bulk than that in solution and was influenced by the different polarities of the solvents. A slight change in the chemical structures of the initiators had no obvious effect on the polymerization rates of MMA and St. The initiator efficiency toward MMA was lower than that toward St. The results of ¹H‐NMR, matrix‐assisted laser desorption/ionization time‐of‐flight mass spectrum analysis, and chain‐extension experiments demonstrated that well‐defined poly(methyl methacrylate) and polystyrene bearing photolabile groups could be obtained via atom transfer radical polymerization (ATRP) with three iniferter reagents as initiators. The polymerization mechanism for this novel initiation system was a common ATRP process. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

ATRP of acrylonitrile catalyzed by FeCl2/succinic acid under microwave irradiation

A single‐pot atom‐transfer radical polymerization (ATRP) under microwave irradiation was first used to successfully synthesize polyacrylonitrile. This was achieved by using FeCl₂/succinic acid as the catalyst and 2‐chloropropionitrile as the initiator. Using the same experimental conditions, the apparent rate constant under microwave irradiation was found to be higher than that under conventional heating. The FeCl₂/succinic acid ratio of 1 : 2 not only gives the best control of molecular weight and its distribution but also provides rather rapid reaction rate. When FeCl₂ was replaced with CuCl, ATRP of AN does not show an obvious living characteristics. To demonstrate the active nature of the polymer chain end, the polymers were used as macroinitiators to proceed the chain‐extension polymerization. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 1598–1601, 2006     

Urotropine as a highly effective and versatile promoter for atom transfer radical polymerization

Atom transfer radical polymerization (ATRP) is a transition metal complex‐catalyzed controlled/‘living’ radical process. Recently, there has been a lot of interest focused on decreasing the catalyst loading and reducing the cost of post‐polymerization purification for ATRP. In this work, urotropine was found to significantly enhance the ATRP of methyl acrylate (MA), methyl methacrylate (MMA) and styrene (St) catalyzed by CuBr/N,N,N′,N′,N″‐pentamethyldiethylenetriamine (PMDETA) and CuBr/tris(2‐(dimethylamino)ethylamine) (Me₆TREN). With the addition of 25 times the amount of urotropine relative to CuBr, well‐controlled polymerizations of MA, MMA and St were obtained at catalyst‐to‐initiator ratios of 0.01, 0.05 and 0.05, respectively, producing the corresponding polymers with molecular weights close to theoretical values and low polydispersities. The catalyst concentration could even be reduced to ppm level at a catalyst‐to‐initiator ratio as low as 0.001 in the polymerization of MA. These results indicate that urotropine is a very effective and versatile promoter for both CuBr/PMDETA and CuBr/Me₆TREN. In the presence of urotropine, the catalyst loading could be reduced by as much as 1000 times. As PMDETA is one of the cheapest ATRP ligands, the combination of urotropine with CuBr/PMDETA could substantially reduce the catalyst loading and the cost of post‐polymerization purification at the industrial scale and thus is promising for potential industrial applications. © 2014 Society of Chemical Industry     

Synthesis of polyacrylonitrile via reverse atom transfer radical polymerization initiated by 1,1,2,2‐tetraphenyl‐1,2‐ethanediol/FeCl3/triphenylphosphine

FeCl₃ coordinated by triphenylphosphine was first used as the catalyst in the 1,1,2,2‐tetraphenyl‐1,2‐ethanediol‐initiated reverse atom transfer radical polymerization of acrylonitrile. A FeCl₃/triphenylphosphine ratio of 0.5 not only gave the best control of the molecular weight and its distribution but also provided a rather rapid reaction rate. The rate of polymerization increased with increasing polymerization temperature, and the apparent activation energy was calculated to be 62.4 kJ/mol. When FeCl₃ was replaced with CuCl₂, the reverse atom transfer radical polymerization of acrylonitrile did not show prominent living characteristics. To demonstrate the active nature of the polymer chain end, the polymers were used as macroinitiators to advance the chain‐extension polymerization in the presence of a CuCl/2,2′‐bipyridine catalyst system via a conventional atom transfer radical polymerization process. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 4041–4045, 2007     

An iron‐based reverse ATRP process for the living radical polymerization of acrylonitrile

A hexa‐substituted ethane thermal iniferter, diethyl‐2,3‐dicyano‐2,3‐di(p‐tolyl) succinate (DCDTS), was firstly used as the initiator in the reverse atom transfer radical polymerization (RATRP) of acrylonitrile. FeCl₃ coordinated by isophthalic acid (IA) was used as the catalyst in this system. The polymerization in N,N‐dimethylformamide not only shows the best control of molecular weight and its distribution but also provides rather rapid reaction rate with the ratio of [AN] : [DCDTS] : [FeCl₃] : [IA] at 500 : 1 : 2 : 4. The polymers obtained were end‐functionalized by chlorine atom, and they were used as macroinitiators to proceed the chain extension polymerization in the presence of FeCl₂/IA catalyst system via a conventional ATRP process and polyacrylonitrile obtained was with M_n = 39,260, PDI = 1.25. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007