Synthesis,antimicrobial, and release behaviors of tetracycline hydrochloride loaded poly (VInyl alcohol)/chitosan/ZrO2 nanofibers

Tetracycline hydrochloride loaded poly (vinyl alcohol)/chitosan/ZrO₂ (Tet‐PVA/CS/ZrO₂) hybrid nanofibers were fabricated via electrospinning technique. The representative weight ratio of PVA/CS at 3 : 1 was chosen to fabricate drug carrier PVA/CS/ZrO₂ nanofibers. The drug carrier showed a decrease in average diameter with the increase of ZrO₂ content at given conditions, and the nanofibers were uneven and interspersed with spindle‐shape beads with ZrO₂ content at 60 wt % and above. The networks linked by hydrogen and Zr–O–C bonds among PVA, CS, and ZrO₂ units resulted in the improving of thermal stability and decreasing of crystallinity of the polymeric matrix. Moreover, the incorporation of ZrO₂ endowed the fibers with ultraviolet shielding effect ranged from 200 to 400 nm. The Tet loading dosage had no obvious effect on the morphology and size of the medicated nanofibers at Tet content below 8 wt %, but interspersed with spindle‐shaped beads when Tet content increased to 10 wt %. The Tet‐PVA/CS/ZrO₂) nanofibers showed well controlled release and better antimicrobial activity against Staphylococcus aureus, and the Tet release from the medicated nanofibers could be described by Fickian diffusion model for M_t /M_∞< 0.6. These medicated nanofibers may have potential as a suitable material in drug delivery and wound dressing. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42506.     

Fabrication and characterization of chitosan/poly(vinyl alcohol) electrospun nanofibrous membranes containing silver nanoparticles for antibacterial water filtration

Electrospun nanofibrous membranes (ENMs) were fabricated based on chitosan/poly(vinyl alcohol) (CS/PVA) with a 70/30 mass ratio containing silver nanoparticles (AgNPs) via the electrospinning method. AgNPs were produced on the surface of CS/PVA nanofibers by adding AgNO₃ to a CS/PVA blend solution as a silver rendering component. The presence of AgNPs in the polymer blend solution was detected by UV spectrophotometry. The morphology of nanofibers before and after cross-linking with glutaraldehyde was investigated by the field emission scanning electron microscopy. The formation and size distribution of AgNPs onto the surface of nanofibers were observed by transmission electron microscopy and confirmed by energy dispersing X-ray spectroscopy. As-spun and cross-linked CS/PVA nanofibers revealed a smooth surface with diameters ranging from 58 to 73 nm and 95 to 109 nm, respectively. The effect of AgNP formation on the chemical structure of nanofibers was explored by Fourier transform infrared spectroscopy. Static and dynamic antibacterial filtration efficiencies of CS/PVA ENMs, containing differing amounts of AgNO₃, have been tested against Escherichia coli, a gram negative bacterium. The antibacterial assessment results exhibited a significant increase in both static and dynamic antibacterial filtration efficiencies of the prepared CS/PVA ENMs by addition of AgNO₃ as a bactericidal agent.     

Synthesis,antimicrobial activity,and release of tetracycline hydrochloride loaded poly(vinyl alcohol)/soybean protein isolate/zirconium dioxide nanofibrous membranes

Tetracycline hydrochloride loaded poly(vinyl alcohol)/soybean protein isolate/zirconium (Tet–PVA/SPI/ZrO₂) nanofibrous membranes were fabricated via an electrospinning technique. The average diameter of the PVA/soybean protein isolate (SPI)/ZrO₂ nanofibers used as drug carriers increased with increasing ZrO₂ content, and the nanofibers were uneven and tended to stick together when the ZrO₂ content was above 15 wt %. The Tet–PVA/SPI/ZrO₂ nanofibers were similar in morphology when the loading dosage of the model drug tetracycline hydrochloride was below 6 wt %. The PVA, SPI, and ZrO₂ units were linked by hydrogen bonds in the hybrid networks, and the addition of ZrO₂ improved the thermostability of the polymer matrix. The Tet–PVA/SPI/ZrO₂ nanofibrous membranes exhibited good controlled drug‐release properties and antimicrobial activity against Staphylococcus aureus. The results of this study suggest that those nanofibrous membranes were suitable for drug delivery and wound dressing. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40903.     

Photosensitive antibacterial and cytotoxicity performances of a TiO2/carboxymethyl chitosan/poly(vinyl alcohol) nanocomposite hydrogel by in situ radiation construction

Nano‐TiO₂/carboxymethyl chitosan (CMCS)/poly(vinyl alcohol) (PVA) ternary nanocomposite hydrogels were prepared by freezing–thawing cycles and electron‐beam radiation with PVA, CMCS, and nano‐TiO₂ as raw materials. The presence of nano‐TiO₂ nanoparticles in the composite hydrogels was confirmed by thermogravimetry, Fourier transform infrared spectroscopy, and X‐ray powder diffraction. Field emission scanning electron microscopy images also illustrated that the TiO₂/CMCS/PVA hydrogel exhibited a porous and relatively regular three‐dimensional network structure; at the same time, there was the presence of embedded nano‐TiO₂ throughout the hydrogel matrix. In addition, the nano‐TiO₂/CMCS/PVA composite hydrogels displayed significant antibacterial activity with Escherichia coli and Staphylococcus aureus as bacterial models. The antibacterial activity was demonstrated by the antibacterial circle method, plate count method, and cell density method. Also, with the Alamar Blue assay, the cytotoxicity of the composite hydrogel materials to L929 cells was studied. The results suggest that these materials had no obvious cytotoxicity. Thus, we may have developed a novel, good biocompatibility hydrogel with inherent photosensitive antibacterial activity with great potential for applications in the fields of cosmetics, medical dressings, and environmental protection. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 44150.     

Ultrasmall Ag nanocrystals supported on chitosan/PVA nanofiber mats with bifunctional properties

Bifunctional nanofiber mats consisting of chitosan (CS), poly(vinyl alcohol) (PVA), and silver nanocrystals (Ag NCs) have been fabricated by a facile electrospinning method. The formation and presence of Ag NCs supported on CS/PVA nanofibers are confirmed by ultraviolet‐visible spectroscopy and X‐ray diffraction. The morphology of the samples is characterized by transmission electron microscopy and scanning electron microscopy. The prepared Ag NCs/CS/PVA nanofiber mats show pronounced antibacterial activity against Escherichia coli and excellent filtration property for suspended particulate matter (SPM) particles. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46504.     

Influence of Syzygium cumini leaves extract on morphological,thermal, mechanical,and antimicrobial properties of PVA and PVA/chitosan blend films

In the present work, poly(vinyl alcohol)/Syzygium cumini leaves extract (PSN) and poly(vinyl alcohol)/chitosan/S. cumini leaves extract blend films were prepared by solution casting technique. The films were characterized by using scanning electron microscopy, atomic force microscopy, X‐ray diffraction study, Fourier transform infrared spectroscopy, thermogravimetric analysis, and universal testing machine. The results indicated that the appreciable physical interaction at lower concentrations of S. cumini leaves extract in the PVA and PVA/chitosan films contribute to the smooth uniform morphology, increased the degree of crystallinity, degradation temperature, and improved mechanical properties. Further, films were analyzed with water contact angle analyzer which illustrates that blend films were hydrophilic (PSN‐1) and hydrophobic (PCS‐1) in nature. However, blend films were also subjected to the antimicrobial study, which revealed that inclusion of S. cumini leaves extracts significantly enhanced the antibacterial activity in the PVA and PVA/chitosan film. With all of these results, fabricated blends can find potential applications in packaging material to extend the shelf life of foodstuffs. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46188.     

Preparation of oligochitosan via In situ enzymatic hydrolysis of chitosan by amylase in [Gly]BF4 ionic liquid/water homogeneous system

The preparation of oligochitosan with excellent performance via in situ enzymatic hydrolysis of chitosan by amylase in ionic liquid system is reported. It has been found that [Gly]BF₄ ionic liquid leads to the good solubility and assistant degradation for chitosan, as well as good biocompatibility for amylase. In the homogeneous system that contained 1.0 g chitosan (degree of deacetylation = 88.5%) and 99.0 g 2 wt % [Gly]BF₄ aqueous solution, oligochitosan with 2200 viscosity‐average molecular weight has been obtained after 0.12 g amylase being used for 3 h at 50°C and pH 5.0. This result is superior to that conducted in acetic acid system. Moreover, [Gly]BF₄ can be easily separated from the product and reused with only slight performance loss (oligochitosan product with 2700 viscosity‐average molecular weight has been obtained after [Gly]BF₄ being reused for five times). In addition, the mechanism for enzymatic hydrolysis of chitosan in [Gly]BF₄ ionic liquid has been described. The research on the moisture‐absorption, ‐retention, and antibacterial activity of oligochitosan product shows that the smaller molecular weight would bring the better moisture‐absorption and antibacterial properties. The oligochitosan product with 2200 viscosity‐average molecular weight exhibits preferable antibacterial properties to S. aureus and E. coli. At the same time, the moisture‐absorption and ‐retention capacity of the above product can reach 32% (relative humidity (RH) = 43%), 62% (RH = 81%), and 150% (RH = 43%), 35% (dry silica gel) respectively. The enzymatic preparation of oligochitosan through [Gly]BF₄ ionic liquid/water homogeneous system can be an efficient and environment‐friendly method for academics and industry. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 41152.     

Preparation and antibacterial activity of PET/chitosan nanofibrous mats using an electrospinning technique

The nanofiber deposition method, by electrospinning, was employed to introduce antibacterial activity and biocompatibility to the surface of poly (ethylene terephthalate) (PET) textiles. The polymer blends of PET and chitosan were electrospun on to the PET micro‐nonwoven mats for biomedical applications. The PET/chitosan nanofibers were evenly deposited on to the surface, and the diameter of the nanofibers was in the range between 500 and 800 nm. The surface of the nanofibers was characterized using SEM, ESCA, AFM, and ATR‐FTIR. The wettability of the PET nanofibers was significantly enhanced by the incorporation of chitosan. The antibacterial activity of the samples was evaluated utilizing the colony counting method against Staphylococcus aureus and Klebsiella pneumoniae. The results indicated that the PET/chitosan nanofiber mats showed a significantly higher growth inhibition rate compared with the PET nanofiber control. In addition, the fibroblast cells adhered better to the PET/chitosan nanofibers than to the PET nanofibers mats, suggesting better tissue compatibility. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Three‐layered electrospun PVA/PCL/PVA nanofibrous mats containing tetracycline hydrochloride and phenytoin sodium: A case study on sustained control release,antibacterial, and cell culture properties

The main objective of this work was to prepare a tailor‐made electrospun nanofibrous samples based on poly(?‐caprolactone) (PCL) containing tetracycline hydrochloride (TC‐HCl) as a middle layer and poly(vinyl alcohol) (PVA) including phenytoin sodium (PHT‐Na) as lateral layers. The characterizations of the three‐layered electrospun samples were carried out by using SEM, ATR‐FTIR spectroscopy along with swelling/weight loss, UV–vis spectrophotometry as well as HPLC, antibacterial and MTT tests. The SEM micrograph images showed that the average diameter of PCL nanofibers was decreased from 243 ± 7 nm to 181 ± 5 nm by adding TC‐HCl. The hydrolytic degradation of PVA nanofibers in the exposure of phosphate buffer solution (PBS) was confirmed by ATR‐FTIR results in which a change at the intensity of the characteristic peak located at 3333 cm^?1 corresponding to hydroxyl groups (? OH) was observed. The UV–vis outcomes revealed a sustained control release of TC‐HCl from the three‐layered nanofibrous samples (PVA/PCL/PVA) with an amount of about 43% compared to the PCL nanofibers which had an ultimate release of the drug about 79%. Furthermore, the HPLC chromatograms showed the released PHT‐Na from PVA nanofibers about 87%. Finally, the MTT assay along with the antibacterial evaluation exhibited that the surfaces of these electrospun three‐layered nanofibrous samples have no cytotoxicity as well as the controlled release of TC‐HCl from them enabled their prolonged use for preventing the bacterium growth such as S. aureus during 24‐h treatment time. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43309.     

Preparation and characterization of polymer‐Ti3C2Tx (MXene) composite nanofibers produced via electrospinning

MXene, a recently‐discovered family of two‐dimensional (2D) transition metal carbides and/or nitrides, have attracted much interest because of their unique electrical, thermal, and mechanical properties. In this study, poly(acrylic acid), poly(ethylene oxide) (PEO), poly(vinyl alcohol) (PVA), and alginate/PEO were electrospun with delaminated Ti₃C₂ (MXene) flakes. The effect of small additions of delaminated Ti₃C₂ (1% w/w) on the structure and properties of the nanofibers were investigated and compared with those of the neat polymer nanofibers using scanning electron microscopy, transmission electron microscopy, X‐ray diffraction, and Fourier transform infrared spectroscopy. Ti₃C₂ had an effect on the solution properties of the polymer and a greater effect on the average fiber diameter. The Ti₃C₂T_x/PEO solution exhibited the largest change in viscosity and conductivity with an 11% and 73.6% increase over the base polymer, respectively. X‐ray diffractograms demonstrated a high degree of crystallization for Ti₃C₂/PEO and a slight decrease in crystallinity for Ti₃C₂/PVA. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45295.     

Preparation of poly(vinyl alcohol)/poly(acrylic acid)/TiO2/carbon nanotube composite nanofibers and their photobleaching properties

The composite nanofibers of poly(vinyl alcohol) (PVA)/poly(acrylic acid) (PAAc)/titanium(IV) oxide (TiO₂) were prepared by electrospinning for a novel photocatalytic treatment of waste water. To improve the photoelectronic properties of PVA/PAAc/TiO₂ composite nanofibers, carbon nanotubes (CNTs) were used as an additive. The TiO₂ and CNTs were immobilized in the PVA/PAAc hydrogels as electrospun nanofibers for an easier recovery after the wastewater treatment. The improved efficiency of pollutant dye removal was observed at pH 10 due to the pH-sensitive swelling behavior of the PVA/PAAc/TiO₂/CNTs composite nanofibers. The photocatalytic activity of TiO₂ was improved noticeably by applying electric field to the CNTs-embedded composite nanofibers.     

In vitro and in vivo investigational studies of a nanocomposite‐hydrogel‐based dressing with a silver‐coated chitosan wafer for full‐thickness skin wounds

A nanocomposite reservoir‐type hydrogel dressing of poly vinyl alcohol (PVA) was fabricated by a freeze–thaw method and loaded with silver‐nanoparticle‐coated chitosan wafers (Ag–CHWs). The Ag–CHWs were synthesized by a sonication technique with silver nitrate (AgNO₃) and chitosan powder. Scanning electron microscopy images showed silver nanoparticles (AgNPs) with a size range of 10 ± 4 nm on the surface of the chitosan wafers, and the antibacterial efficacy (minimum inhibitory concentration) of the Ag–CHWs was measured against Pseudomonas aeruginosa (32 µg/mL), Staphylococcus aureus, (30 µg/mL) and Escherichia coli (32 µg/mL). The antimicrobial PVA hydrogel showed an improved tensile strength (～0.28 MPa) and gel content (～92%) in comparison with the blank hydrogels. Full‐thickness‐excision wound studies of the nanocomposite dressing on Wistar rats revealed enhanced wound contraction, improved inflammation response, re‐epithelization rate, neoangiogenesis, and granulation tissue formation in comparison to the control group. A flexible, biocompatible, nanocomposite reservoir dressing not only established the chitosan as a stabilizer but also proved the efficacious and safe utility of AgNPs toward chronic wound management. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43472.     

Electrospun polyvinyl alcohol/waterborne polyurethane composite nanofibers involving cellulose nanofibers

TEMPO‐oxidized cellulose nanofibers (TOCNs) were used as nanofillers in this work. Composite nanofibers of polyvinyl alcohol (PVA)/waterborne polyurethane (WPU) reinforced with TOCNs were produced by electrospinning. The reinforcing capability of TOCNs was investigated by tensile tests. Scanning electron microscopy (SEM), X‐ray diffraction, and thermogravimetry analyses were also carried out in order to characterize the appearance, crystallinity, and reinforcing effect of the cellulose nanofibers. SEM results showed that PVA/WPU/TOCNs composite nanofibers presented a highly homogeneous dispersion of TOCNs. The reinforced composites had about 44% increase in their mechanical properties with addition of only 5 wt % of TOCNs while about 42% decrease in elongation at break. The TOCNs reinforced composite nanofibers were more thermally stable than pure PVA/WPU nanofibers. The development of crystalline structure in the composite fibers was observed by XRD. Since PVA, WPU, and TOCNs are hydrophilic, non‐toxic, and biocompatible, and therefore, these nanocomposite nanofibers could be used for tissue scaffolding, filtration materials, and medical industries as wound dressing materials. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 41051.     

Preparation of syndiotacticity‐rich high molecular weight poly(vinyl alcohol)/iodine polarizing film with high water resistance

To enhance durability of poly(vinyl alcohol) (PVA)/iodine polarizing film under humid and warm atmospheres and to identify the effects of syndiotacticity on the polarizing efficiency (PE) and durability of PVA/iodine complex film, we prepared three high molecular weight (PVA)s with similar number‐average degree of polymerization (P_n) of 4000 and with different syndiotactic diad (s‐diad) contents of 53, 56, and 59%, respectively. It was found that syndiotacticity of PVA had a significant influence on the durability of PVA/iodine complex film in warm and humidity conditions (relative humidity of 80% and temperature of 50°C). That is, both desorption of iodine in PVA/iodine film and transmittance of film decreased with increasing syndiotacticity of PVA. In the case of PE, the values of over 99% were obtained at each optimum conditions. The change of PE (durability) of PVA/iodine complex films having P_n of 4000 and s‐diad contents of 56 and 59%, respectively, in warm and humidity conditions was almost zero, whereas those of PVA/iodine film with s‐diad content of 53% and with (P_n)s of 1700 and 4000 were about 60% and 50%, respectively, under same conditions. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Palladium nanoparticles embedded chitosan/poly(vinyl alcohol) composite nanofibers as an efficient and stable heterogeneous catalyst for Heck reaction

In this study, palladium nanoparticles were successfully embedded into modified chitosan/poly(vinyl alcohol) composite nanofibers (Pd-CS/PVA nanofibers) by electrospinning. Then, the Pd-CS/PVA nanofibers were treated at evaluated temperature to improve its solvent resistance and in situ reduce Pd²⁺ cations into Pd⁰ active species. The incorporated palladium nanoparticles with ultra small mean diameter of 3.73 ± 1.04 nm are evenly distributed inside the Pd-CS/PVA nanofiber. The resulting Pd-CS/PVA nanofiber mat exhibits high catalytic activity for Heck reaction of aromatic iodides with alkenes and can be recycled for 18 times without loss of initial activity. The high catalytic activity and stability of Pd-CS/PVA nanofiber mat can be attributed to the ultra small diameter nanofibers, strong chelating ability of chitosan, and fine embedment of palladium species inside the nanofiber. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 48026.     

Rheological properties of high molecular weight (HMW) syndiotactic poly(vinyl alcohol) (PVA)/HMW atactic PVA blend solutions

To identify the effect of blend ratios of syndiotacticity‐rich poly(vinyl alcohol) (s‐PVA)/atactic PVA (a‐PVA) having similar number‐average degrees of polymerization (P_n)s of 4000 and degrees of saponification (DS)s of 99.9% on the rheological properties of s‐PVA/a‐PVA/water solutions, water‐soluble s‐PVA and a‐PVA with different syndiotactic diad contents of 58.5 and 54.0%, respectively, were prepared by bulk copolymerization of vinyl pivalate and vinyl acetate (VAc) and solution polymerization of VAc, followed by saponifying the corresponding copoly(vinyl pivalate/vinyl acetate) and poly(vinyl acetate). The blend ratios played a significant role in rheological behavior. Over the frequency range of 10^?1–10² rad/s, s‐PVA/a‐PVA blend solutions with larger s‐PVA content show more shear thinning at similar (P_n)s and (DS)s of polymer, suggesting that PVA molecules are more readily oriented as s‐PVA content increases. Yield stress is higher for s‐PVA/a‐PVA blend solutions with larger s‐PVA content at similar (P_n)s and (DS)s of polymer. This indicates that more domains with internal order are produced at larger s‐PVA content in s‐PVA/a‐PVA blend solutions. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 3934–3939, 2006     

Drug‐release behavior of chitosan‐g‐poly(vinyl alcohol) copolymer matrix

Chitosan‐g‐poly(vinyl alcohol) (PVA) copolymers with different grafting percent were prepared by grafting water‐soluble PVA onto chitosan. The drug‐release behavior was studied using the chitosan‐g‐PVA copolymer matrix containing prednisolone in a drug‐delivery system under various conditions. The relationship between the amount of the released drug and the square root of time was linear. From this result, the drug‐release behavior through the chitosan‐g‐PVA copolymer matrix is shown to be consistent with Higuchi's diffusion model. The drug‐release apparent constant (K_H) was slightly decreased at pH 1.2, but increased at pH 7.4 and 10 according to the increasing PVA grafting percent. Also, K_H was decreased by heat treatment and crosslinking. The drug release behavior of the chitosan‐g‐PVA copolymer matrix was able to be controlled by the PVA grafting percent, heat treatment, or crosslinking and was also less affected by the pH values than was the chitosan matrix. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 458–464, 1999     

Electrospinning fabrication and characterization of poly(vinyl alcohol)/layered double hydroxides composite fibers

Nanofibers of poly(vinyl alcohol) (PVA)/layered double hydroxide (Mg‐Al LDH) composites are prepared by the electrostatic fiber spinning using water as the solvent at a high voltage of 21 kV. Either inorganic LDH carbonate (LDH‐CO₃) or L ‐lactic acid‐modified LDH (Lact‐LDH) is used for incorporating with PVA. Scanning electron microscopy SEM investigations on the nanofibers suggest that the average diameters of PVA/LDH composite fibers are smaller than that of neat PVA. Transmission electron microscopy (TEM) investigations indicate that the dispersity of the LDH in PVA matrix is much improved after modification with L ‐lactic acid. The mechanical properties of the PVA/LDH fibers are obviously enhanced compared to that of neat PVA. For example, the tensile stress and elongation at break of the PVA/Lact‐LDH electrospun fibrous mat with 5 wt % Lact‐LDH are 31.7 MPa and 36.7%, respectively, which are significantly higher than those of neat PVA, and also higher than those of PVA/LDH‐CO₃ owing to the better dispersity of Lact‐LDH nanoparticles. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Preparation and antibacterial activity of polyvinyl alcohol/regenerated silk fibroin composite fibers containing Ag nanoparticles

Polyvinyl alcohol (PVA)/regenerated silk fibroin (SF)/AgNO₃ composite nanofibers were prepared by electrospinning. A large number of nanoparticles containing silver were generated in situ and well‐dispersed nanoparticles were confirmed by transmission electron microscopy (TEM) intuitionally. Ultraviolet (UV)‐visible spectroscopy and X‐ray diffraction (XRD) patterns indicated that nanoparticles containing Ag were present both in blend solution and in composite nanofibers after heat treatment and after subsequent UV irradiation. By annealing the nanofibers, Ag⁺ therein was reduced so as to produce nanoparticles containing silver. By combining heat treatment with UV irradiation, Ag⁺ was transformed into Ag clusters and further oxidized into Ag₃O₄ and Ag₂O₂. Especially size of the nanoparticles increased with heat treatment and subsequent UV irradiation. This indicated that the nanoparticles containing silver could be regulated by heat treatment and UV irradiation. The antimicrobial activity of heat‐treated composite nanofibers was evaluated by Halo test method and the resultant nanofibers showed very strong antimicrobial activity. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Morphology enhancement of TiO2/PVP composite nanofibers based on solution viscosity and processing parameters of electrospinning method

In this work, different sol solutions with various titanium tetraisopropoxide (TIP)/glacial acetic acid ratios in 2‐propanol with 5 wt % poly(vinyl pyrrolidone) (PVP) (M_w = 360,000 g/mol) were prepared and electrospun. Composition of the prepared sols and as‐spun TiO₂/PVP nanofibers were determined by Fourier transform infrared and Raman spectroscopy methods. Morphology of the electrospun TiO₂/PVP nanofibers was studied by scanning electron microscopy and transmission electron microscopy (TEM) techniques. Rheometry measurements of the sol solutions showed decrease of viscosity upon the addition of TIP to the polymer solutions with constant polymer and acid concentrations. The sol solution having the lowest viscosity (at shear rate 10 s^?1) but the highest TIP/glacial acetic acid ratio showed beaded nanofibers morphology when electrospun under 10 and 12 kV applied voltage while injection rate, needle tip to collector distance, and needle gauge were kept constant. However, smooth electrospun TiO₂/PVP composite nanofibers with the average nanofibers diameters (148 ± 79 nm) were achieved under the same condition when applied voltage increased to 15 kV. TEM micrographs of the electrospun TiO₂/PVP nanofiber showed that the TiO₂ particles with continuous structure are formed at the middle of the nanofiber and distributed along its axis. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46337.