Polyimide‐polyurethane/urea block copolymers for highly sensitive humidity sensor with low hysteresis

Polyimide (PI)‐polyurethane‐urea (PU) block copolymers (PI‐PU75/25, PI‐PU50/50, and PI‐PU25/75) were prepared by reaction between anhydride‐terminated poly(amic acid) prepolymers with various number‐average degree of polymerization = 73/49/25) and isocyanate‐terminated urethane‐urea prepolymers with various (11/21/31) to obtain high performance capacitive humidity sensors. Pure PI and PU were also prepared to compare with PI‐PU copolymers. This study examined the effect of PU content on the water absorption %/water vapor transmission rate, thermal and mechanical properties and sensing properties of PI‐PU block copolymers. The thermal stability and mechanical properties of the copolymer decreased markedly with increasing PU content. The sensitivity of sensor increased sharply with increasing PU content from 0 to 25 wt %, and then increased a little. The hysteresis of sensor decreased sharply with increasing PU content up to 50 wt %, and then decreased a little. These results demonstrate the apparent upside of using two copolymers (PI‐PU75/25 and PI‐PU50/50) compared to using pure PI, in terms of sensor performance. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44973.     

Surface properties of block and graft polystyrene–polydimethylsiloxane copolymers

The surface compositions of a series of polystyrene‐b‐polydimethylsiloxane (PS‐b‐PDMS) and polystyrene‐g‐polydimethylsiloxane (PS‐g‐PDMS) copolymers were investigated using ATR‐FTIR and XPS technique. The results showed that enrichment of PDMS soft segments occurred on the surface of the block copolymers as well as on that of graft copolymers. And the magnitude order of the enrichment was as follows: PS‐b‐PDMS > PS‐g‐PDMS, which was attributed to the facilitating of the movement of the PDMS segments in PS‐b‐PDMS copolymer. Meanwhile, the solvent type and the contact medium had influence on the accumulation of PDMS on the surfaces. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci, 2006     

Electrospun nonwovens of shape‐memory polyurethane block copolymers

Synthesized shape‐memory polyurethane (PU) block copolymers were used to prepare electrospun nonwovens via electrospinning. PU solutions were prepared with a mixed solvent of N,N‐dimethylformamide and tetrahydrofuran. The electrospun PU nonwovens were prepared with hard‐segment concentrations of 40 and 50 wt %. The morphology of the electrospun fibers was investigated with scanning electron microscopy. The average diameter of low‐viscosity (ca. 130–180 cPs) electrospun fibers was about 800 nm, and the morphology of the electrospun nonwovens was beaded‐on fibers. In contrast, the average diameter of high‐viscosity (ca. 530–570 cPs) electrospun fibers was about 1300 nm. In an investigation of the mechanical properties of the electrospun PU nonwovens, it was found that the tensile strength increased as the hard‐segment concentration increased within a similar range of viscosities. Also, the tensile strength of the electrospun PU nonwovens in the machine direction was higher than that in the transverse direction because of a difference in the velocities of the drum collectors. The electrospun PU nonwovens with hard‐segment concentrations of 40 and 50 wt % were found to have a shape recovery of more than 80%. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 96: 460–465, 2005     

Novel poly(methyl methacrylate)‐block‐polyurethane‐block‐poly(methyl methacrylate) tri‐block copolymers through atom transfer radical polymerization

Poly(methyl methacrylate)‐block‐polyurethane‐block‐poly(methyl methacrylate) tri‐block copolymers have been synthesized successfully through atom transfer radical polymerization of methyl methacrylate using telechelic bromo‐terminated polyurethane/CuBr/N,N,N,N″,N″‐pentamethyldiethylenetriamine initiating system. As the time increases, the number‐average molecular weight increases linearly from 6400 to 37,000. This shows that the poly methyl methacrylate blocks were attached to polyurethane block. As the polymerization time increases, both conversion and molecular weight increased and the molecular weight increases linearly with increasing conversion. These results indicate that the formation of the tri‐block copolymers was through atom transfer radical polymerization mechanism. Proton nuclear magnetic resonance spectral results of the triblock copolymers show that the molar ratio between polyurethane and poly (methyl methacrylate) blocks is in the range of 1 : 16.3 to 1 : 449.4. Differential scanning calorimetry results show T_g of the soft segment at ?35°C and T_g of the hard segment at 75°C. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

丙烯腈嵌段共聚物的合成及其自组装研究进展

综述了含聚丙烯腈(PAN)嵌段共聚物的合成方法及其在溶液中的自组装技术。对常用的活性自由基聚合方法,如原子转移自由基聚合(ATRP)、可逆加成断裂链转移(RAFT)聚合、氮氧自由基聚合(NMP)以及钴调介自由基聚合(CMRP)等方面的研究进行了总结,同时对PAN类嵌段共聚物在溶液中的自组装技术进行了概括。最后提出了现有技术存在的问题,并对其今后发展方向进行了展望。     

Starlike Nylon 6/polyurethane block copolymers by reaction injection‐molding process (RIM)

Starlike block copolymers of Nylon‐6 and polyurethane were synthesized using ε‐caprolactam as a monomer, caprolactam magnesium bromide as a catalyst, and a star prepolymer of polyurethane. These copolymers were compared with the linear block copolymers of Nylon‐6 and polyurethane. Such copolymers were obtained using the reaction injection‐molding process (RIM) of ε‐caprolactam at different contents of polyurethane (5–30 wt %). In increasing the content of the soft phase, in FTIR, a displacement was observed in the band at 1637 cm^?1, assigned to the amide I of the Nylon 6, to a higher wavenumber. This suggests a bigger interaction between the urethane group of the polyurethane and the amide group of the Nylon 6. Star block copolymers showed better mechanical properties compared with the linear ones. This behavior is attributed to the higher crystallinity and ramifications present in the materials. The structure and the thermal properties of the copolymers were studied using different techniques such as DSC, WAXS, DMA, and SEM. A decrease in the crystallinity when increasing the soft phase was also observed. Finally, physical tensile, impact, and hardness tests of the copolymers were carried out. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 2483–2494, 2001     

Synthesis and surface properties of polydimethylsiloxane‐based block copolymers: poly[dimethylsiloxane‐block‐ (ethyl methacrylate)] and poly[dimethylsiloxane‐block‐(hydroxyethyl methacrylate)]

A polydimethylsiloxane (PDMS) macroazoinitiator was synthesized from bis(hydroxyalkyl)‐terminated PDMS and 4,4′‐azobis‐4‐cyanopentanoic acid by a condensation reaction. The bifunctional macroinitiator was used for the block copolymerization of ethyl methacrylate (EMA) and 2‐(trimethylsilyloxy)ethyl methacrylate (TMSHEMA) monomers. The poly(DMS‐block‐EMA) and poly(DMS‐block‐TMSHEMA) copolymers thus obtained were characterized using Fourier transform infrared and ¹H NMR spectroscopy and differential scanning calorimetry. After the deprotection of trimethylsilyl groups, poly(DMS‐block‐HEMA) and poly(DMS‐block‐EMA) copolymer film surfaces were analysed using scanning electron microscopy and X‐ray photoelectron spectroscopy. The effects of the PDMS concentration in the copolymers on both air and glass sides of films were examined. The PDMS segments oriented and moved to the glass side in poly(DMS‐block‐EMA) copolymer film while orientation to the air side became evident with increasing DMS content in poly(DMS‐block‐HEMA) copolymer film. The block copolymerization technique described here is a versatile and economic method and is also applicable to a wide range of monomers. The copolymers obtained have phase‐separated morphologies and the effects of DMS segments on copolymer film surfaces are different at the glass and air sides. Copyright © 2010 Society of Chemical Industry     

新型聚硅氧烷嵌段共聚物的合成研究进展

聚硅氧烷作为一种有机硅高聚物,可通过嵌段共聚进行相应的化学改性。综述了国内外新型聚硅氧烷嵌段共聚物的研究进展,主要对纯聚硅氧烷嵌段型、聚醚型、聚烯烃型和聚氨酯型进行了叙述,并对其应用前景进行了展望。     

Controlled/living RAFT polymerization of N‐phenyl maleimide and synthesis of its block copolymers

The controlled/living radical polymerization of N‐phenyl maleimide (NPMI) was achieved using 2,2′‐azobisisobutyronitrile as the initiator and 2‐cyanopropyl‐2‐yl dithiobenzoate as the reversible addition‐fragmentation chain transfer agent at 75°C in dichloroethane/ethylene carbonate (60/40, w/w) mixed solvent. The block copolymers of polystyrene‐b‐polyNPMI and poly(n‐butyl methacrylate)‐b‐polyNPMI were successfully prepared by chain extension from dithiobenzoate‐terminated polystyrene and poly (n‐butyl methacrylate) to NPMI, respectively. The obtained NPMI‐based (co)polymers were characterized by gel permeation chromatography and ¹H‐NMR spectroscopy. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Nitroxide‐terminated poly(styrene‐co‐diethyl fumarates) and derived block copolymers

Copolymerization of styrene (S) and diethyl fumarate (DEF) at 125°C in the presence of 2,2,6,6‐ tetramethylpiperidin‐1‐yloxyl radical (TEMPO) and initiated with a thermal initiator, 2,2′‐azobisisobutyronitrile (AIBN), was studied. The molar fraction of DEF in the feed, F_DEF, varied within 0.1–0.9. An azeotropic composition, (F_DEF)_A = 0.38, was found for the copolymerization under study. At F_DEF = 0.1–0.4, a quasi‐living process was observed, transforming to a retarded conventional radical copolymerization at a higher content of DEF in the initial mixtures. The obtained TEMPO‐terminated S‐DEF copolymers were used to initiate polymerization of styrene. Poly(styrene‐ co‐diethyl fumarate)‐block‐polystyrene copolymers were prepared with molecular weight distributions depending on the amount of inactive polymer chains in macroinitiators, as indicated by size‐exclusion chromatography. A limited miscibility of the blocks in the synthesized block copolymers was revealed by using differential scanning calorimetry. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 2432–2439, 2002     

The amphiphilic block copolymers of 2-(dimethylamino)ethyl methacrylate and methyl methacrylate: Synthesis by atom transfer radical polymerization and solution properties

Amphiphilic di- and tri-block copolymers of poly(methyl methacrylate) (PMMA) and poly(2-dimethylamino)ethyl methacrylate (PDMAEMA) have been synthesized by atom transfer radical polymerization (ATRP) at ambient temperature (35 °C) in the environment-friendly solvent, aqueous ethanol (water 16 vol%) using CuCl/o-phenanthroline as the catalyst. The PDMAEMA blocks are contaminated with ethyl methacrylate (EMA) residues to the extent of 1-2 mol% of DMAEMA depending on the length of the PDMAEMA block. The EMA forms through the autocatalyzed ethanolysis of the DMAEMA monomer and undergoes random copolymerization with the latter. The rate of ethanolysis is unexpectedly greater in the aqueous ethanol than in neat ethanol, which has been attributed to the higher polarity of the former than of the latter. In contrast to the ethanolysis no hydrolysis of DMAEMA in the aqueous ethanol medium could be detected for 133 h. The block copolymers form micelles in water. Their solubility and CMC in neutral water have been studied. Dynamic light scattering (DLS) studies reveal that for a fixed degree of polymerization (DP) of the PMMA block the hydrodynamic diameter of the micelles in methanolic water (water 95 vol%) increases at a faster rate with the DP of the PDMAEMA block when it is much greater than that of the PMMA block compared to when it is less than or close to that of the latter.     

Poly(styrene‐co‐N‐butylmaleimide) macroinitiators by controlled autopolymerization and related block copolymers

Autopolymerization of styrene‐N‐butylmaleimide mixtures at 125 or 140°C in the presence of a stable nitroxyl radical [2,2,6,6‐tetramethylpiperidin‐1‐yloxyl (TEMPO)] was found to proceed in a pseudoliving manner. Unimolecular initiators, which were originated by trapping self‐generated radical species with TEMPO, took part in the process. Under the studied experimental conditions, the TEMPO‐controlled autopolymerization with a varying comonomer ratio provided virtually alternating copolymers of narrow molecular weight distributions. The molecular weights of the copolymers increased with conversions. The obtained styrene‐N‐butylmaleimide copolymers containing TEMPO end groups were used to initiate the polymerization of styrene. The polymerization yielded poly(styrene‐co‐N‐butylmaleimide)‐polystyrene block copolymers with various polystyrene chain lengths and narrow molecular weight distributions. The compositions, molecular weights, and molecular weight distributions of the synthesized block copolymers and the initial poly(styrene‐co‐N‐butylmaleimide) precursors were evaluated using nitrogen analysis, gel permeation chromatography, and ¹H‐ and ¹³C‐NMR spectroscopy. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 2378–2385, 1999     

Alternating block copolymers based on polyamide‐12 and polycaprolactone

A series of alternating polyester/polyamide block copolymers were prepared by sequential conversion of hydroxy‐terminated polycaprolactone and amino‐terminated polyamide‐12 with a selectively reacting coupling agent. The thermal properties of the block copolymers were investigated using differential scanning calorimetry and dynamic mechanical analysis. Mechanical properties were determined using tensile and impact tests. All polymers were phase‐separated, where the polyamide phase was semicrystalline in all compositions. Distinct crystallization of the polycaprolactone phase was observed only when the block length was greater than 2000 g mol^?1. Mechanical testing showed that the polymers behave in a manner similar to that of thermoplastic elastomers. In particular, samples with a high content of polycaprolactone showed high strain and good impact behaviour. Copyright © 2011 Society of Chemical Industry     

Synthesis and characterization of hydroxypropyl terminated polydimethylsiloxane‐polyurethane copolymers

Polyurethane (PU) block copolymers were synthesized using prepared hydroxypropyl terminated polydimethylsiloxane (HTPDMS MW 990) and polyether diols (N‐210) as soft segment with 4,4′‐diphenylmethane diisocyanate (MDI) and 1,4‐butanediol. This low molecular weight polydimethylsiloxanes (PDMS) containing hydroxypropyl end‐groups displayed better compatibility with PU than common PDMS. In this article, we illustrate its synthesis routes and confirmed the proposed molecular structures using NMR and infrared radiation (IR). We varied the contents of HTPDMS and N‐210 in soft segments (HTPDMS—N‐210: 0 : 100, 20 : 80, 40 : 60, 60 : 40, 80 : 20, and 100 : 0) to synthesize a series of PDMS‐PU copolymer. IR spectroscopy showed the assignment characteristic groups of each peak in copolymers and confirmed that the desired HTPDMS‐PU copolymers have been prepared. The different thermal, dynamic mechanical and surface properties of the copolymers were compared by thermogravimetry, DMA, contact angle and solvent resistance. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Styrene–butadiene block copolymer with high cis‐1,4 microstructure

The sequential block copolymerization of styrene (St) and butadiene (Bd) was carried out with an activated rare earth catalyst composed of catalyst neodymium tricarboxylate (Nd), cocatalyst Al(i‐Bu)₃ (Al), and chlorinating agent (Cl). The microstructure, composition, and morphology of the copolymer were characterized by FTIR, ¹H NMR, ¹³C NMR, and TEM. The results show that styrene–butadiene diblock copolymer with high cis‐1,4 microstructure of butadiene units (～ 97 mol %) was synthesized. The cis‐selectivity for Bd units was almost independent on the content of styrene units in the copolymer ranging from 18.1 mol % to 29.8 mol %. The phase‐separated morphology of polystyrene (PS) domains of about 40 nm tethered by the elastomeric polybutadiene (PB) segments is observed. The PS‐b‐cis‐PB copolymer could be used as an effective compatilizer for noncompatilized binary PS/cis‐PB blends. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Controlled synthesis of vinyl-functionalized homopolymers and block copolymers by RAFT polymerization of vinyl methacrylate

Reversible addition-fragmentation chain transfer (RAFT) polymerization of an asymmetrical divinyl monomer, vinyl methacrylate (VMA), was investigated under various conditions. RAFT polymerization of VMA using a dithioester-type chain transfer agent (CTA) under suitable conditions afforded soluble polymers with a high content of pendant vinyl ester side chains in sufficient yields (>70%). The monomer concentration, the nature of the CTA, and the CTA/initiator ratio were found to affect the polymerization reaction and the structure of the resulting polymers; this behavior is attributed to the relative propensities for intermolecular propagating/cross-linking reactions and intramolecular cyclization. A kinetic study of the RAFT polymerization of VMA with the dithioester-type CTA 1 suggested that the propagation reaction of the methacryloyl group proceeded predominantly with a certain level of intramolecular cyclization during the early stage of the polymerization and intermolecular cross-linking during the final stage of the polymerization. Block copolymers with one segment featuring pendant vinyl functionality were synthesized by RAFT polymerization of VMA using poly(methyl methacrylate) as a macro-chain transfer agent (macro-CTA).     

Domain and segment orientation behavior of PBS–PTMG segmented block copolymers

Segment and domain orientation behaviors of a series of poly(butylene succinate) (PBS) –poly(tetramethylene glycol) (PTMG) segmented block copolymers containing different amounts of hard segment were studied with synchrotron small‐angle X‐ray scattering (SAXS) and infrared dichroic methods. Copolymers used in this work consist of PBS as a hard segment, and poly(tetramethylene oxide) (PTMO) of molecular weight 2000g/mol as a soft segment. As hard‐segment content increased, phase‐separated morphology changed from a phase of continuous soft matrix containing isolated hard domain to one of continuous hard matrix. Upon stretching, domains responded differently depending on their initial orientation. Based on SAXS results, two major domain deformation modes, that is, lamellar separation and shear compression, were suggested. The orientation behavior of the hard and soft segments was examined with infrared dichroic method. Upon drawing, the orientation function of the crystalline hard segment decreased at low‐draw ratios. It was interpreted in terms of rotation of long axis of hard domain along the stretching direction. The lowest value of the orientation function of PBS30 was approximately −0.5, that is, theoretical minimum. This result seems to indicate that for PBS30 containing about 30% hard segment, rotation of hard domain occurs without appreciable interdomain interaction, which is consistent with the morphological model suggested on the basis of SAXS results. Plastic deformation of the hard domain due to domain breakup was found to occur at low‐draw ratios for the sample containing higher hard‐segment content. Domain mechanical stability was tested by drawing a sample up to three different maximum draw ratios. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 699–709, 2000     

Formation of phase structure and crystallization behavior in blends containing polystyrene–polyethylene block copolymers

The microphase separation structure in the molten state and the structure formation in crystallization from such ordered melt were investigated for the blends of polystyrene–polyethylene block copolymers (SE) with polystyrene homopolymer (PS) and polyethylene homopolymer (PE) and for the blends consisting of two kinds of SE with different copolymer compositions from each other, using synchrotron small-angle X-ray scattering techniques (SAXS). The copolymer compositions of SE block copolymers employed were 0.34, 0.58 and 0.73 wt. fraction of PE, and their melt morphologies were cylindrical, lamellar and lamellar, respectively. Macrophase separation or the morphology change in the melt occurred depending on the molecular weight and the blend composition, as reported so far. In crystallization from such macrophase-separated and microphase-separated melts, the melt morphology was completely kept for all the blends. Crystallization behavior was also investigated for the blends. The crystallization within the spherical and cylindrical domains surrounded by glassy PS was not observed for SE/PS blends. In the crystallization from the macrophase-separated melt, two exothermal peaks were observed in the DSC measurements, while a single peak was observed for other blends. For the blends with PS, the degree of crystallinity was depressed and the apparent activation energy of crystallization was high, compared to those for the corresponding neat SE. For SE/PE and SE/SE blends, those were changed depending on the blend composition.     

Hybridization of aqueous‐based polyurethane with glycidyl methacrylate copolymer

The carboxyl group containing aqueous‐based polyurethane (PU) dispersions were prepared from isophorone diisocyanate, poly(propylene glycol)‐1000, and 2,2‐dimethylol propanic acid via a PU prepolymer process. The amino content of this amino‐terminated aqueous‐based PU system was determined by a styrene oxide titration method. Glycidyl methacrylate (GMA) copolymer emulsions were prepared by an emulsion polymerization of GMA and other alkyl acrylates. The curing behavior of the GMA copolymer was demonstrated by a model reaction of the GMA copolymer with ethylenediamine. In the same token, the reaction took place between the PU amino groups and the GMA copolymer epoxides at ambient temperature and resulted in the formation of a hybridized homogeneous copolymer. This hybridized copolymer also consisted of carboxylic acid on the PU fraction after drying. Carboxylic acids of the copolymer were exchanged with calcium ion and this ionic coordination resulted in a calcium ion‐crosslinked copolymer. The physical and mechanical properties and the thermal behaviors of the hybridized copolymers were evaluated. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 71: 903–913, 1999     

Hydrogels based on polyurethane–polyacrylic acid multiblock copolymers via macroiniferter technique

Polyurethane (PU)–polyacrylic acid (PAAc) multiblock copolymers have been prepared via a macroiniferter technique, and were tested for living mechanism, thermal, and water swell of the cast films. It was found that molecular weight of the PU–PAAc block copolymers linearly increased while molecular weight distribution decreased with conversion. As the PAAc content increases, water swell of the cast films and crystalline melting temperature (T_m) of PU decreased while glass transition temperature of PU increased.