Effect of monomer composition on properties of copolyimides derived from 3,3′,4,4′‐biphenyltetracarboxylic dianhydride/4,4′‐oxydianiline/1,3‐bis (4‐aminophenoxy)benzene

A series of uncontrolled molecular weight homopolyimides and copolyimides based on 3,3′,4,4′‐biphenyltetracarboxylic dianhydride (s‐BPDA)/4,4′‐oxydianiline (4,4′‐ODA)/1,3‐bis(4‐aminophenoxy)benzene (TPER) were synthesized. All the polyimides displayed excellent thermal stability and mechanical properties, as evidenced by dynamic thermogravimetric analysis and tensile properties testing. A singular glass transition temperature (T_g) was found for each composite from either differential scanning calorimetry (DSC) or dynamic mechanical analysis (DMA), but the values determined from tan δ of DMA were much different from those determined from DSC and storage modulus (E′) of DMA. The Fox equation was used to estimate the random T_g values. Some composites exhibited re‐crystallization after quenching from the melt; upon heating, multi‐melting behavior was observed after isothermal crystallization at different temperatures. The equilibrium melting temperature was estimated using the Hoffman‐Weeks method. Additionally, DMA was conducted to obtain E′ and tan δ. Optical properties were strongly dependent on the monomer composition as evidenced by UV‐visible spectra. X‐ray diffraction was used to interpret the crystal structure. All the results indicated that composites with TPER composition ≥ 70% were dominated by the TPER/s‐BPDA polyimide phase, and ≤40% by the 4,4′‐ODA/s‐BPDA polyimide phase. When the ratio between the two diamines was close to 1:1, the properties of the copolyimides were very irregular, which means a complicated internal structure. Copyright © 2011 Society of Chemical Industry     

Highly fluorinated poly(ether‐imide)s derived from 2,2′‐bis(3,4,5‐trifluorophenyl)‐4,4′‐diaminodiphenyl ether and aromatic dianhydrides

A new diamine, 2,2′‐bis(3,4,5‐trifluorophenyl)‐4,4′‐diaminodiphenyl ether (FPAPE) was synthesized through the Suzuki coupling reaction of 2,2′‐diiodo‐4,4′‐dinitrodiphenyl ether with 3,4,5‐trifluorophenylboronic acid to produce 2,2′‐bis(3,4,5‐trifluorophenyl)‐4,4′‐dinitrodiphenyl ether (FPNPE), followed by palladium‐catalyzed hydrazine reduction of FPNPE. FPAPE was then utilized to prepare a novel class of highly fluorinated all‐aromatic poly(ether‐imide)s. The chemical structure of the resulting polymers is well confirmed by infrared and nuclear magnetic resonance spectroscopic methods. Limiting viscosity numbers of the polymer solutions at 25 °C were measured through the extrapolation of the concentrations used to zero. M_n and M_w of these polymers were about 10 000 and 25 000 g mol^?1, respectively. The polymers showed a good film‐forming ability, and some characteristics of their thin films including color and flexibility were investigated qualitatively. An excellent solubility in polar organic solvents was observed. X‐ray diffraction measurements showed that the fluoro‐containing polymers have a nearly amorphous nature. The resulting polymers had T_g values higher than 340 °C and were thermally stable, with 10% weight loss temperatures being recorded above 550 °C. Based on the results obtained, FPAPE can be considered as a promising design to prepare the related high performance polymeric materials. Copyright © 2011 Society of Chemical Industry     

Synthesis and characterization of cross‐linkable poly(phthalazinone ether ketone)s

A novel class of crosslinkable poly(phthalazinone ether ketone)s with relative high molecular‐weight and good solubility were successfully synthesized by the copolymerization of bisphthalazinone containing monomer, 3,3′‐diallyl‐4,4′‐dihydroxybiphenyl and 4,4′‐di‐ fluorobenzophenone. The synthesized polymers with inherent viscosities in the range of 0.42 to 0.75 dL/g can form flexible and transparent membranes by casting from their solution. The crosslinking reaction of these polymers can be carried out by thermally curing of the virgin polymers in or without the presence of crosslinking agent. The experimental results demonstrated that the crosslinking reaction also occurred to some extent during the polymerization. The crosslinked polymers exhibited equivalent glass transition temperature (T_g) at lower crosslinking density, and showed higher T_g than virgin polymers at higher crosslinking density. The crosslinked high‐temperature polymer can be used as the base material for high temperature adhesive, coating, enamel material, and composite matrices. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Proton Conducting Membranes Based on Poly(2,2′‐imidazole‐5,5′‐bibenzimidazole)

Poly(2,2′‐imidazole‐5,5′‐bibenzimidazole) (PBI‐imi) was synthesized via the polycondensation between 3,3′,4,4′‐tetraaminobiphenyl and 4,5‐imidazole‐dicarboxylic acid. Effects of the reaction conditions on the intrinsic viscosity of the synthesized polymers were studied. The results show that the molecular weight of the polymers increases with increasing monomer concentration and reaction time, and then levels off. With higher reaction temperature, the molecular weight of the polymer is higher. With the additional imidazole group in the backbone, PBI‐imi shows improved phosphoric acid doping ability, as well as a little higher proton conductivity when compared with widely used poly[2,2′‐(m‐phenylene)‐5,5′‐bibenzimidazole] (PBI‐ph).Whereas, PBI‐imi and PBI‐ph have the similar chemical oxidation stability. PBI‐imi/3.0 H₃PO₄ composite membranes exhibit a proton conductivity as high as 10^–4 S cm^–1 at 150 °C under anhydrous condition. The temperature dependence of proton conductivity of acid doped PBI‐imi can be modeled by an Arrhenius equation.     

Resistive switching characteristics of polyimides derived from 2,2′‐aryl substituents tetracarboxylic dianhydrides

2,2′‐Position aryl‐substituted tetracarboxylic dianhydrides including 2,2′‐bis(biphenyl)‐4,4′,5,5′‐biphenyl tetracarboxylic dianhydride and 2,2′‐bis[4‐(naphthalen‐1‐yl)phenyl)]‐4,4′,5,5′‐biphenyl tetracarboxylic dianhydride were synthesized. A new series of aromatic polyimides (PIs) were synthesized via a two‐step procedure from 3,3′,4,4′‐biphenyl tetracarboxylic dianhydride and the newly synthesized tetracarboxylic dianhydrides monomers reacting with 2,2′‐bis[4′‐(3″,4″,5″‐trifluorophenyl)phenyl]‐4,4′‐biphenyl diamine. The resulting polymers exhibited excellent organosolubility and thermal properties associated with T_g at 264 °C and high initial thermal decomposition temperatures (T_5%) exceeding 500 °C in argon. Moreover, the fabricated sandwich structured memory devices of Al/PI‐a/ITO was determined to present a flash‐type memory behaviour, while Al/PI‐b/ITO and Al/PI‐c/ITO exhibited write‐once read‐many‐times memory capability with different threshold voltages. In addition, Al/polymer/ITO devices showed high stability under a constant stress or continuous read pulse voltage of ? 1.0 V. Copyright © 2011 Society of Chemical Industry     

Microwave assisted polycondensation of polyimides by [4,4′‐(hexafluoroisopropylidene)diphthalic anhydride,pyromellitic dianhydride] and [2,4,6‐trimethyl‐m‐phenylenediamine]. Power,time, and solvent effect

The microwave assisted polycondensation of two polyimides were studied using pyromellitic dianhydride (PMDA), and 4,4′‐(hexafluoroisopropyliden)diphthalic anhydride (6FDA) as dianhydride monomers and 2,4,6‐trimethyl‐m‐phenylenediamine (TrmPD), as diamine monomer, under microwave irradiation in DMF and DMSO solvents. The structure and performance of polymers were characterized by Fourier Transform Infrared Spectroscopy (FTIR), viscosity, density, and Thermogravimetric Analysis (TGA). The results show that the polyimides can be obtained in a short reaction time with high intrinsic viscosity and high yield. The effect of the presence of a bridging group, ? C(CF₃)₂? , in the monomer structure is apparent in the permeability parameters of the macromolecules as polymer (6FDA‐TrmPD) always presents better results than polymer (PMDA‐TrmPD). Properties as density and T_g increases with the time exposition to the microwave irradiation. Polyimides obtained present good thermal properties because they began to lose weight in a range of 8–16% at high temperature as 450°C. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Molecular simulation of the glass transition and proton conductivity of 2,2′‐benzidinedisulfonic acid and 4,4′‐diaminodiphenylether‐2,2′‐disulfonic acid‐based copolyimides as polyelectrolytes for fuel cell applications

The glass transition temperatures (T_gs) and proton conductivities of polyimides synthesized from naphthalene‐1,4,5,8‐tetracarboxylic dianhydride (NTDA), 2,2′‐benzidinedisulfonic acid (BDSA), 4,4′‐diaminodiphenylether‐2,2′‐disulfonic acid (ODADS), and non‐sulfonated diamine monomers have been predicted using molecular dynamics simulations. The specific volumes for two dry and four hydrated NTDA‐based polyimides were plotted versus temperatures above and below T_gs to obtain the glass transition temperatures. The simulation results suggest that the ODADS‐based polyimide membranes exhibit lower T_gs and thus better mechanical properties than the BDSA‐based polyimides, which may be attributed to the high mobility of backbones of ODADS as supported by the vectorial autocorrelation function (VACF) results of this study. In addition, comparison of the simulated T_gs for the dry and hydrated ODADS‐based polyimides has shown that water content in polyimides can affect their T_gs. The proton conductivities of a representative polyimide in both dry and hydrated conditions have been obtained from molecular dynamics simulations of the proton and hydronium ion diffusion. The simulated conductivity for the hydrated NTDA‐ODADS/BAPB cell is in reasonable agreement with the experimental value obtained from the AC impedance method. The relationship between the chemical composition, chain flexibility, and the glass transition and proton conduction of these NTDA‐based polyimides was explored on the basis of VACF and pair correlation function analysis. Copyright © 2006 Society of Chemical Industry     

Synthesis and properties of new aromatic polyimides based on 2,2′‐dibromo‐4,4′,5,5′‐benzophenone tetracarboxylic dianhydride

New polyimides with enhanced thermal stability and high solubility were synthesized in common organic solvents from a new dianhydride, 2,2′‐dibromo‐4,4′,5,5′‐benzophenone tetracarboxylic dianhydride (DBBTDA). DBBTDA was used as monomer to synthesize polyimides by using various aromatic diamines. The polymers were characterized by IR and NMR spectroscopy and elemental analysis. These polyimides had good inherent viscosities in N‐methyl‐2‐pyrrolidinone (NMP) and also high solubility and excellent thermo‐oxidative stability, with 5 % weight loss in the range 433 to 597 °C. Copyright © 2004 Society of Chemical Industry     

Novel poly(thiourea‐ether‐imide)s derived from 4,4′‐oxydiphenyl‐bis(thiourea): probing the possibility for high‐temperature applications

Our interest in the fabrication of high‐performance polyimides has led to thiourea‐substituted poly(thiourea‐ether‐imide)s (PTEIs) with good retention of thermal properties along with flame retardancy. A new aromatic monomer, 4,4′‐oxydiphenyl‐bis(thiourea) (ODPBT), was efficiently synthesized and polymerized with various dianhydrides (pyromellitic dianhydride, 3,3′,4,4′‐benzophenonetetracarboxylic dianhydride and 4,4′‐(hexafluoroisopropylidene)diphthalic dianhydride) via two‐stage chemical imidization to fabricate a series of PTEIs. The structural characterization of ODPBT and the polymers was carried out using Fourier transform infrared, ¹H NMR and ¹³C NMR spectral techniques along with crystallinity, organosolubility, inherent viscosity and gel permeation chromatographic measurements. PTEIs bearing C?S and ? O? moieties in the backbone demonstrated an amorphous nature and were readily soluble in various amide solvents. The novel polymers had inherent viscosities of 1.16–1.23 dL g^?1 and molecular weights of ca 90 783–96 927 g mol^?1. Their thermal stability was substantiated via 10% weight loss in the temperature range 516–530 °C under inert atmosphere. The polyimides had glass transition temperatures of 260–265 °C. Incorporation of thiourea functionalities into polymer backbones is demonstrated to be an effective way to enhance their thermal properties and flame retardancy. Thus, ODPBT can be considered as an excellent candidate for use in the synthesis of high‐performance polymeric materials. Copyright © 2010 Society of Chemical Industry     

Preparation of Transparent Polyimides Derived from cis‐ and trans‐Dicyclohexyl‐3,3′,4,4′‐tetracarboxylic Dianhydrides

Two series of alicyclic polyimides composed of cis‐ and trans‐dicyclohexyl‐3,3′,4,4′‐tetracarboxylic dianhydrides (DCDAs) and aromatic diamines were prepared. All cis‐polymers could be readily prepared both in a one‐step method and a two‐step method. However, a two‐step method is preferably applied in the preparation of trans‐polymers, because in a one‐step method the trans‐configuration is partially lost at higher temperatures. These polyimide solutions could be cast into tough and flexible films, which were characterized by inherent viscosity, GPC, DSC, TGA measurements, and UV‐vis spectroscopy. The glass transition temperatures (T_g's) of the polymers were in the range of 210–270°C and the 5% weight loss temperatures were around 480°C for all PIs prepared. The optical transmittances of these films were more than 80% at 350 nm for ca. 15 μm thickness.     

Synthesis and characterization of new soluble poly(ester‐imide)s containing noncoplanar 2,2′‐dimethyl‐4,4′‐biphenylene unit

A new diimide–diacid chloride (3) containing a noncoplanar 2,2′‐dimethyl‐4,4′‐biphenylene unit was synthesized by treating 2,2′‐dimethyl‐4,4′‐diamino‐biphenylene with trimellitic anhydride followed by refluxing with thionyl chloride. Various new poly(ester‐imide)s were prepared from 3 with different bisphenols by solution polycondensation in nitrobenzene using pyridine as hydrogen chloride quencher at 170°C. Inherent viscosities of the poly(ester‐imide)s were found to range between 0.31 and 0.35 dL g^?1. All of the poly(ester‐imide)s, except the one containing pendent adamantyl group 5e, exhibited excellent solubility in the following solvents: N,N‐dimethylformamide, tetrahydrofuran, tetrachloroethane, dimethyl sulfoxide, N,N‐dimethylacetamide, N‐methyl‐2‐pyrrolidinone, m‐cresol, o‐chlorophenol, and chloroform. The polymers showed glass‐transition temperatures between 166 and 226°C. The 10% weight loss temperatures of the poly(ester‐imide)s, measured by TGA, were found to be in the range between 415 and 456°C in nitrogen. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 2486–2493, 2004     

Structure and characterization for conterminously linked polymer of short‐chain epoxy resin with triallyl isocyanurate and bismaleimide

The short‐chain epoxy resin (SCER) was prepared direct from epichlorohydrin/bisphenol A (ECH/BPA). The resulted SCER and 4,4′‐diaminodiphenyl sulfone (DDS) with various weight percent of triallyl isocyanurate/4,4′‐bismaleimidophenylmethane (TAIC/BMI) were subsequently thermally coreacted to the corresponding high performance materials for high frequency application. They were characterized using potentiometry, Fourier transform infrared (FTIR), differential scanning calorimetry (DSC), thermogravimetric analyses (TGA), dielectric analyzer, and scanning electron microscope (SEM). Dynamic mechanical analysis (DMA) of polymers showed only a T_g indicating a low entropy, amorphous state and formed a conterminously linked polymer. The morphology of polymers revealed no phase separation. The formation of polymer was in good agreement with the proposed molecular structure, and has enhanced good thermal, mechanical, and electric properties. Furthermore, with lower nitrogen content was achieved UL‐94 V‐0 rating. No fume and toxic gas emission were observed during burning test for this system. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 2470–2480, 2006     

Synthesis and luminescence properties of new blue‐light‐emitting polyconjugated poly{1,1′‐biphenyl‐4,4′‐diyl‐[1‐(4‐t‐butylphenyl)]vinylene} polymers and copolymers

Three new soluble polyconjugated polymers, all of which emitted blue light in photoluminescence and electroluminescence, were synthesized, and their luminescence properties were studied. The polymers were poly{1,1′‐biphenyl‐4,4′‐diyl‐[1‐(4‐t‐butylphenyl)]vinylene}, poly((9,9‐dioctylfluorene‐2,7‐diyl)‐alt‐{1,4‐phenylene‐[1‐(4‐t‐butylphenyl)vinylene‐1,4‐phenylene]}) [P(DOF‐PVP)], and poly([N‐(2‐ethyl) hexylcarbazole‐3,6‐diyl]‐alt‐{1,4‐phenylene‐[1‐(4‐t‐butylphenyl)]vinylene‐1,4‐phenylene}). The last two polymers had alternating sequences of the two structural units. Among the three polymers, P(DOF‐PVP) performed best in the light‐emitting diode devices of indium–tin oxide/poly(ethylenedioxythiophene) doped with poly(styrene sulfonate) (30 nm)/polymer (150 nm)/Li:Al (100 nm). This might have been correlated with the balance in and magnitude of the mobility of the charge carriers, that is, positive holes and electrons, and also the electronic structure, that is, highest occupied molecular orbital (HOMO) and lowest unoccupied molecular orbital (LUMO) levels, of the polymers. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 307–317, 2006     

Copolycondensation of IPA/TPA,BPA, and 4,4′‐dihydroxydipehnylsulfone and 4,4′‐dicarboxydiphenylsulfone

Copolycondensations of IPA, TPA, bisphenol A (BPA), and several cimonomers were carried out to improve thermal properties, such as, the glass transition temperature (T_g) of the IPA/TPA (50/50)–BPA polyester. Among the comonomers examined, 4,4′‐Dihydroxydiphenylsulfone (BPS) and 4,4′‐Dicarboxydiphenylsulfone (DCDPS) having a strongly dipolar sulfonyl group in the chain were significantly effective. The favorable effect upon the T_gs was studied by varying the amounts of BPS and DCDPS incorporated into the copolymers. In the copolycondensation with BPS, two‐stage copolycondensation of BPA first and then BPS, the reverse order of reaction, and their spontaneous addition were examined to investigate the effect of distribution of the BPS unit segments in the copolymer upon the T_gs of the resulted copolymers. The distribution was briefly studied from distribution of the IPA/TPA‐BPA oligomers in the initial reaction using GPC. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 875–879, 2000     

Synthesis and characterization of novel aromatic poly(amide‐imide)s derived from 2,2′‐bis(4‐trimellitimidophenoxy)biphenyl or 2,2′‐bis(4‐trimellitimidophenoxy)‐1,1′‐binaphthyl and various aromatic diamines

New aromatic diimide‐dicarboxylic acids having kinked and cranked structures, 2,2′‐bis(4‐trimellitimidophenoxy)biphenyl (2a) and 2,2′‐bis(4‐trimellitimidophenoxy)‐1,1′‐binaphthyl (2b), were synthesized by the reaction of trimellitic anhydride with 2,2′‐bis(4‐aminophenoxy)biphenyl (1a) and 2,2′‐bis(4‐aminophenoxy)‐1,1′‐binaphthyl (1b), respectively. Compounds 2a and 2b were characterized by FT‐IR and NMR spectroscopy and elemental analyses. Then, a series of novel aromatic poly(amide‐imide)s were prepared by the phosphorylation polycondensation of the synthesized monomers with various aromatic diamines. Owing to structural similarity, and a comparison of the characterization data, a model compound was synthesized by the reaction of 2b with aniline. The resulting polymers with inherent viscosities of 0.58–0.97 dl g^?1 were obtained in high yield. The polymers were fully characterized by FT‐IR and NMR spectroscopy. The ultraviolet λ_max values of the poly(amide‐imide)s were also determined. The polymers were readily soluble in polar aprotic solvents. They exhibited excellent thermal stabilities and had 10% weight loss at temperatures above 500 °C under a nitrogen atmosphere. Copyright © 2003 Society of Chemical Industry     

Preparation of poly(amic acid) and polyimide derived from 3,3′,4,4′‐benzophenonetetracarboxylic dianhydride with different diamines by microwave irradiation

Polycondensation‐type poly(amic acid) (PAA) was synthesized with 3,3′,4,4′‐benzophenonetetracarboxylic dianhydride as a dianhydride monomer and 4,4′‐diaminodiphenylmethane and 4,4′‐oxydianiline as diamine monomers under microwave irradiation in dimethylformamide. Then, PAA was used to make polyimide (PI) by imidization at a low temperature. The structure and performance of the polymers were characterized with Fourier transform infrared (FTIR), proton nuclear magnetic resonance (¹H‐NMR), viscosity, X‐ray diffraction (XRD), and thermogravimetry (TG) curve analyses. The FTIR spectra of the polymers showed characteristic peaks of PI around 1779 and 1717 cm^?1. The ¹H‐NMR spectrum of PAA indicated a singlet at 6.55 ppm assigned to ? NHCO? and a singlet at 10.27 ppm assigned to carboxylic acid protons. The XRD spectrum demonstrated that the obtained PI had a low‐order aggregation structure with a d‐spacing of 0.5453 nm. The TG results revealed that the PI was thermally stable with 10% weight loss at 565°C in an N₂ atmosphere. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

Synthesis and characterization of homo‐ and copolymers of 3‐(2‐cyano ethoxy)methyl‐ and 3‐[methoxy(triethylenoxy)]methyl‐3′‐methyl‐oxetane

Two oxetane‐derived monomers 3‐(2‐cyanoethoxy)methyl‐ and 3‐(methoxy(triethylenoxy)) methyl‐3′‐methyloxetane were prepared from the reaction of 3‐methyl‐3′‐hydroxymethyloxetane with acrylonitrile and triethylene glycol monomethyl ether, respectively. Their homo‐ and copolyethers were synthesized with BF₃· Et₂O/1,4‐butanediol and trifluoromethane sulfonic acid as initiator through cationic ring‐opening polymerization. The structure of the polymers was characterized by FTIR and¹H NMR. The ratio of two repeating units incorporated into the copolymers is well consistent with the feed ratio. Regarding glass transition temperature (T_g), the DSC data imply that the resulting copolymers have a lower T_g than pure poly(ethylene oxide). Moreover, the TGA measurements reveal that they possess in general a high heat decomposition temperature. The ion conductivity of a sample (P‐AN 20) is 1.07 × 10^?5 S cm^?1 at room temperature and 2.79 × 10^?4 S cm^?1 at 80 °C, thus presenting the potential to meet the practical requirement of lithium ion batteries for polymer electrolytes. Copyright © 2005 Society of Chemical Industry     

Synthesis and characterization of new optically active poly(amide‐imide‐urethane) thermoplastic elastomers,derived from 4,4′‐(hexafluoroisopropylidene)‐N,N′‐bis(phthaloyl‐L‐leucine‐p‐aminobenzoic acid) and PEG‐MDI

A new class of optically active poly(amide‐imide‐urethane) was synthesized via two‐step reactions. In the first step, 4,4′‐methylene‐bis(4‐phenylisocyanate) (MDI) reacts with several poly(ethylene glycols) (PEGs) such as PEG‐400, PEG‐600, PEG‐2000, PEG‐4000, and PEG‐6000 to produce the soft segment parts. On the other hand, 4,4′‐(hexafluoroisopropylidene)‐N,N′‐bis(phthaloyl‐L ‐leucine‐p‐amidobenzoic acid) (2) was prepared from the reaction of 4,4′‐(hexafluoroisopropylidene)‐N,N′‐bis(phthaloyl‐L ‐leucine) diacid chloride with p‐aminobenzoic acid to produce hard segment part. The chain extension of the above soft segment with the amide‐imide 2 is the second step to give a homologue series of poly(amide‐imide‐urethanes). The resulting polymers with moderate inherent viscosity of 0.29–1.38 dL/g are optically active and thermally stable. All of the above polymers were fully characterized by IR spectroscopy, elemental analyses, and specific rotation. Some structural characterization and physical properties of this new optically active poly(amide‐imide‐urethanes) are reported. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 2288–2294, 2004     

N‐(2‐biphenylenyl)‐4‐[2′‐phenylethynyl] phthalimide: 2. Detailed study of the monomer cure and properties of the resulting polymer

A detailed study is presented of the high‐temperature cure of the difunctional monomer N‐(2‐biphenylenyl)‐4‐[2′‐phenylethynyl]phthalimide (BPP) and the thermal properties of the resulting homopolymer. Although the phenylethynyl groups are consumed within 1 h at 370 °C, other reactions continue well after this, leading to a cured polymer whose glass transition temperature (T_g) is highly dependent on cure time and temperature. A T_g of 450 °C is achieved after a 16 h cure at 400 °C. Use of chemometrics to analyse the infrared spectra of curing BPP provides evidence for changes in the aromatic moieties during cure, perhaps indicative of co‐reaction between the biphenylene and phenylethynyl groups; however, other processes also contribute to the overall complex cure mechanism. Despite the high T_g values, BPP homopolymer exhibits unacceptably poor thermo‐oxidative stability at 370 °C, showing a weight loss of about 50 % after 100 h ageing. This is perhaps a result of formation of degradatively unstable crosslink structures during elevated‐temperature cure. Copyright © 2004 Society of Chemical Industry     

Synthesis and properties of fluorinated aromatic poly(amide imide)s based on 4,4′‐bis(4‐amino‐2‐trifluoromethylphenoxy)benzophenone and various bis(trimellitimide)s

A CF₃‐containing diamine, 4,4′‐bis(4‐amino‐2‐trifluoromethylphenoxy)benzophenone ( 2 ), was synthesized from 4,4′‐dihydroxybenzophenone and 2‐chloro‐5‐nitrobenzotrifluoride. Imide‐containing diacids ( 3 and 5B_a – 5B_g ) were prepared by the condensation reaction of aromatic diamines and trimellitic anhydride. Then, two series of novel soluble aromatic poly(amide imide)s (PAIs; 6A_a – 6A_k and 6B_a – 6B_g ) were synthesized from a diamine ( 4A_a – 4A_k or 2 ) with the imide‐containing diacids ( 3 and 5B_a – 5B_g ) via direct polycondensation with triphenyl phosphate and pyridine. The aromatic PAIs had inherent viscosities of 0.74–1.76 dL/g. All of the synthesized polymers showed excellent solubility in amide‐type solvents, such as N‐methyl‐2‐pyrrolidone and N,N‐dimethylacetamide (DMAc), and afforded transparent and tough films by DMAc solvent casting. These polymer films had tensile strengths of 90–113 MPa, elongations at break of 8–15%, and initial moduli of 2.0–2.9 GPa. The glass‐transition temperatures of the aromatic PAIs were in the range 242–279°C. They had 10% weight losses at temperatures above 500°C and showed excellent thermal stabilities. The 6B series exhibited less coloring and showed lower yellowness index values than the corresponding 6A series. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102:3641–3653, 2006