Mass transport of direct methanol fuel cell species in sulfonated poly(ether ether ketone) membranes

Homogeneous membranes based on sulfonated poly(ether ether ketone) (sPEEK) with different sulfonation degrees (SD) were prepared and characterized. In order to perform a critical analysis of the SD effect on the polymer barrier and mass transport properties towards direct methanol fuel cell species, proton conductivity, water/methanol pervaporation and nitrogen/oxygen/carbon dioxide pressure rise method experiments are proposed. This procedure allows the evaluation of the individual permeability coefficients in hydrated sPEEK membranes with different sulfonation degrees. Nafion^® 112 was used as reference material. DMFC tests were also performed at 50 °C. It was observed that the proton conductivity and the permeability towards water, methanol, oxygen and carbon dioxide increase with the sPEEK sulfonation degree. In contrast, the SD seems to not affect the nitrogen permeability coefficient. In terms of selectivity, it was observed that the carbon dioxide/oxygen selectivity increases with the sPEEK SD. In contrast, the nitrogen/oxygen selectivity decreases. In terms of barrier properties for preventing the DMFC reactants loss, the polymer electrolyte membrane based on the sulfonated poly(ether ether ketone) with SD lower or equal to 71%, although having slightly lower proton conductivity, presented much better characteristics for fuel cell applications compared with the well known Nafion^® 112. In terms of the DMFC tests of the studied membranes at low temperature, the sPEEK membrane with SD = 71% showed to have similar performance, or even better, as that of Nafion^® 112. However, the highest DMFC overall efficiency was achieved using sPEEK membrane with SD = 52%.     

sPEEK based composite membranes for direct ethanol fuel cell applications

In this paper, sulfonated poly(ether ether ketone) (sPEEK) based composite membranes are discussed. The inorganic matrix consisted of silica: Aerosil^® 380, tetraethoxysilane (TEOS), or a combination of both to obtain an interconnected silica network. The ion exchange capacity (IEC) was determined and these values coincided with the predicted IEC values. Uptake in water and 2 M ethanol was performed and an optimum was obtained. TEOS promoted the uptake due to its hydrophilicity. Proton conductivity values of the composite membranes and the polymeric reference were similar, although the IEC was lower. The stability of the composite membranes could be improved by adding an imidazole based functional silane to the composite system. This stability increased with increasing imidazole content resulting in remarkably lower ethanol permeability.     

Blend membranes based on disulfonated poly(aryl ether ether ketone)s (SPEEK) and poly(amide imide) (PAI) for direct methanol fuel cell usages

Highly disulfonated poly(aryl ether ether ketone)s (SPEEK-70) copolymer was synthesized via direct polymerization to precisely control the degree of sulfonation (D_s = 1.40), which was confirmed and estimated by ¹H NMR. As expected, the proton conductivity of SPEEK-70 membrane is 0.084 S/cm at 25 °C and increases to 0.167 S/cm at 80 °C, surpassing that of Nafion^® 117. However, the relatively high methanol crossover and excessively swelling properties limited its usage in DMFC. Poly(amide imide) was blended with SPEEK-70 to improve the methanol resistance and mechanical properties. These blend membranes were characterized as a function of weight fraction of PAI in terms of ion exchange capacity (IEC), water uptake, water desorption, proton conductivity and methanol permeability in detail. Although the proton conductivities decreased upon the addition of PAI, higher selectivity values defined as the ratio of proton conductivity to methanol permeability were found for the blend membranes. Therefore, the SPEEK/PAI blend membranes are promising for usage in DMFC.     

Proton exchange membrane bearing entangled structure: Sulfonated poly(ether ether ketone)/bismaleimide hyperbranch

Physical cross-linking of sulfonated poly(ether ether ketones) sPEEKs with hyper-branched bismaleimide oligomer (modified bismaleimide, mBMI) leads to densely packed polymer. Different curing conditions on the two sPEEK samples containing Bismaleimide (BMI) monomer and modified Bismaleimide oligomers (mBMI) mole ratios of 70:30 (mBMI(30)) and 2:98 (mBMI(98)) are present. As the amount of BMI monomer increases, the branched structure and their degree of entanglement with sPEEK polymer matrix also increase. More rigid and more compact membrane is found in the case of mBMI(30). In contrast, relatively loose entangled network is found for mBMI(98) sample where the mBMI unit remains far apart and mostly un-connected, until high concentration of mBMI(98) is present. The branched structure and their degree of entanglement with sPEEK polymer matrix increases with longer curing time. The results shows physical cross-linking with highly branched mBMI is effective in reducing water uptake, lower methanol permabiity with reduced sPEEK membrane swelling. Except for heavily entangled sample (sPEEK/mBMI(30)) annealed for 20 h, all membranes displayed fair proton conductivity above 10⁻² S/cm at room temperature. Methanol permeability is also substantially reduced to 1.39 × 10⁻⁷ cm²/s for sPEEK/15% mBMI(98). The DMFC single cell assembled by the sPEEK/20% mBMI(98) membrane (59 μm thickness) displayed the highest OCV of 839 mV with a power density reaching 30 mW/cm² at 60 °C. This value is higher than that using sPEEK membrane alone.     

Transport properties of sulfonated poly (styrene‐isobutylene‐styrene) membranes with counter‐ion substitution

In this study, the transport properties of poly(styrene‐isobutylene‐styrene) (SIBS) were determined as a function of sulfonation level (0–94.9%) and counter‐ion substitution (Ba⁺², Ca⁺², Mg⁺², Mn⁺², Cu⁺², K⁺¹) for fuel cell applications. Increasing the sulfonation level improved the ion exchange capacity (IEC) of the membranes up a maximum (1.71 mequiv/g), suggesting a complex three‐dimensional network at high sulfonation levels. Results show that proton conductivity increases with IEC and is very sensitive to hydration levels. Methanol permeability, although also sensitive to IEC, shows a different behavior than proton conductivity, suggesting fundamental differences in their transport mechanism. The incorporation of counter‐ion substitution decreases both methanol and proton transport. Methanol permeability seems to be related to the size of the counter‐ion studied, while proton conductivity is more sensitive to water content, which is also reduced upon the incorporation of counter‐ions. To complement the studies, selectivity (i.e., proton conductivity/methanol permeability) of the studied membranes was determined and compared to Nafion® 117. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Sulfonated poly(arylene ether ketone)s prepared by direct copolymerization as proton exchange membranes: Synthesis and comparative investigation on transport properties

Sulfonated poly(aryl ether ketone)s (SPAEK) copolymers were synthesized by aromatic nucleophilic polycondensation from 3,3′, 5,5′‐tetramethyl‐4, 4′–biphenol, 1,4‐bis(4‐fluorobenzoyl) benzene, and disulfonated difluorobenzophenone. The SPAEK membranes did not exhibit excessive swelling in hot water and at the same time show the proton conductivities in the range of 0.030 S/cm to 0.099 S/cm at 80°C. The methanol diffusion coefficients of the SPAEK membranes were in the range of 4.7 × 10^?7 to 8.1 × 10^?7cm²/s measured at 25°C. The transport properties of this series of SPAEK copolymers were compared to poly(aryl ether ether ketone)s (SPEEK), poly(aryl ether ether ketone ketone)s (SPEEKK), and Nafion® membranes. It was found that the transport properties (including proton conductivity and methanol permeability) follows the trend of SPEEKK‐60 < SPAEK‐60 < SPEEK‐60 < Nafion® 117, the order of which is also attributed to the differences in the chemical structure of the polymers and the membrane morphology. In general, this novel series of SPAEK membranes possess various advantages, such as low cost of the initial monomers, high thermal and mechanical stability, and low methanol permeability while simultaneously possessing sufficient proton conductivity, which makes them notably promising as proton exchange membrane (PEM) materials in direct methanol fuel cell (DMFC) applications. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Sulfonated poly(ether ether ketone)/epoxy/phenol novolac blend proton‐exchange membranes with low methanol permeability

A crosslinked epoxy [4,4′‐diglycidyl‐(3,3′,5,5′‐tetramethylbiphenyl) epoxy resin (TMBP)], cured by phenol novolac (PN), was introduced into a sulfonated poly(ether ether ketone) (SPEEK) membrane (ion‐exchange capacity = 2.0 mequiv/g) with a casting‐solution, evaporation, and heating crosslinking method to improve the mechanical properties, dimensional stability, water retention, and methanol resistance. By Fourier transform infrared analysis, the interactions between the sulfonic acid groups and hydroxyl groups in the blend membranes were confirmed. The microstructure and morphology of the blend membranes were investigated with atomic force microscopy. As expected, the blend membranes showed excellent mechanical properties, good thermal properties (thermal stability above 200°C), lower swelling ratios (1.4% at 25°C and 7.0% at 80°C), higher water retention (water diffusion coefficient = 9.8 × 10^?6 cm²/s), and a lower methanol permeability coefficient (3.6 × 10^?8 cm²/s) than the pristine SPEEK membrane. Although the proton conductivity of the blend membranes decreased, a higher selectivity (ratio of the proton conductivity to the methanol permeability) was obtained than that of the pristine SPEEK membrane. The results showed that the SPEEK/TMBP/PN blend membranes could have potential use as proton‐exchange membranes in direct methanol fuel cells. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Cross‐linked Poly(arylene ether ketone) Proton Exchange Membranes with High Ion Exchange Capacity for Fuel Cells

Sulfonated poly(arylene ether ketone) (SPAEK) possessing the pendant carboxylic acid groups was synthesized. The carboxylic acid groups of SPAEK were reacted with a cross‐linking reagent to prepare a cross‐linked membrane with a high ion exchange capacity (IEC), a high oxidative stability, and an excellent mechanical strength. The cross‐linking hindered the mobility of the polymer chains and thus strongly affected the water uptake and the methanol permeability of the membranes. Also, as the cross‐linker used in this study bore sulfonic acid groups, cross‐linking did not lead to a noticeable loss of the proton conductivity. The cross‐linked SPAEK membrane with 20% cross‐linking density, CSPAEK‐20% membrane, exhibited a high proton conductivity of 0.045 S cm^–1 associated with a high IEC value of 1.78 mmol g^–1 but a low methanol permeability of 4.3 × 10^–7 cm² s^–1. The CSPAEK‐20% membrane also showed excellent cell performance and oxidation resistance.     

Sulfonated poly(ether sulfone)/silica composite membranes for direct methanol fuel cells

A series of sulfonated poly(ether sulfone) (SPES)/silica composite membranes were prepared by sol–gel method using tetraethylorthosilicate (TEOS) hydrolysis. Physico–chemical properties of the composite membranes were characterized by thermogravimetric analysis (TGA), X‐ray diffraction (XRD), scanning electron microscope–energy dispersive X‐ray (SEM–EDX), and water uptake. Compared to a pure SPES membrane, SiO₂ doping in the membranes led to a higher thermal stability and water uptake. SEM–EDX indicated that SiO₂ particles were uniformly embedded throughout the SPES matrix. Proper silica loadings (below 5 wt %) in the composite membranes helped to inhibit methanol permeation. The permeability coefficient of the composite membrane with 5 wt % SiO₂ was 1.06 × 10^?7 cm²/s, which was lower than that of the SPES and just one tenth of that of Nafion® 112. Although proton conductivity of the composite membranes decreased with increasing silica content, the selectivity (the ratio of proton conductivity and methanol permeability) of the composite membrane with 5 wt % silica loading was higher than that of the SPES and Nafion® 112 membrane. This excellent selectivity of SPES/SiO₂ composite membranes could indicate a potential feasibility as a promising electrolyte for direct methanol fuel cell. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Water recovery from flue gas using polyether block amide 2533/sulfonated poly(ether ether ketone) composite membrane

Recycling water from flue gas of coal-fired power plants is of great significance to save energy and water resources and reduce environmental pollution. In the present work, two potential polymers (polyether block amide 2533(PEBAX 2533) and sulfonated poly(ether ether ketone) (SPEEK)) were investigated and showed high water vapor permeability and selectivity, respectively. Combined with the advantages of the two materials, a novel PEBAX 2533/SPEEK composite membrane with an ultra-thin SPEEK selection layer on the outer surface of the high permeable PEBAX 2533 layer was prepared by dip coating. The composite membranes were assembled into a membrane capsule module and tested directly in artificial and real flue gas. The condensed water vapor fluxes were 1006.9 g/m².h in artificial flue gas and 600–900 g/m².h on average in real flue gas during a period of 30 days, exhibiting good water vapor permeability and durability in real flue gas.     

Poly(ether sulfone) supported hybrid poly(vinyl alcohol)–maleic acid–silicone dioxide membranes for the pervaporation separation of ethanol–water mixtures

Microporous poly(ether sulfone) (PES) supported hybrid polymer–inorganic membranes were prepared by the crosslinking of poly(vinyl alcohol) (PVA), maleic acid (MA), and SiO₂ via an aqueous sol–gel route and a solution‐casting method. The membrane performance was tested for the pervaporation separation of ethanol–water mixtures from 20 to 60 °C with a feed ethanol concentration of 96 wt %. The membrane characterization results reveal that different SiO₂ loadings affected the crystallinity and roughness of the membranes. The PVA–MA–SiO₂ membrane containing 10 wt % SiO₂ showed that SiO₂ nanoparticles were well dispersed within the polymer matrix; this resulted in significant enhancements in both the flux and selectivity. The membrane achieved a high water permeability of 1202 g·μm·m^?2 h^?1 kPa^?1 and a selectivity of 1027 for the separation of a 96 wt % ethanol‐containing aqueous solution. This enhanced membrane performance might have been due to the dense crosslinking membrane network, increased free volume, and uniform distribution of SiO₂ nanoparticles. Both the water and ethanol fluxes increased with the feed water concentration and temperature. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134 , 44839.     

Proton exchange membrane based on crosslinked sulfonated polyphosphazene containing pendent perfluorosulfonic acid groups with sulfonated poly(ether ether ketone)

A series of crosslinked membranes based on new sulfonated polyphosphazene bearing pendent perfluorosulfonic acid groups (PMFP‐g‐PS) and sulfonated poly (ether ether ketone) were prepared and evaluated as proton exchange membranes for direct methanol fuel cells (DMFCs). The structure of PMFP‐g‐PS was characterized by Fourier transform infrared spectroscopy, ¹H and ¹⁹F NMR spectra. In comparison with the pristine PMFP‐g‐PS membrane, the crosslinked membranes showed improved water uptakes and proton conductivities. The methanol permeability values of the membranes were in the range of 1.32 × 10^?7 to 3.85 × 10^?7 cm²/s, which were lower than Nafion 117 (12.1 × 10^?7 cm²/s). The selectivity of all the membranes was much higher compared with Nafion 117. Furthermore, transmission electron microscopy observation revealed that clear phase‐separated structures were well dispersed and connected to each other in the membranes. These membranes displayed high water uptakes and low swelling ratios, high proton conductivities, low methanol permeability values, good thermal, and oxidative stabilities. The results indicate that these membranes are potential candidate proton exchange membrane materials for DMFCs. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43492.     

Preparation of novel semihomogeneous cation‐permeable membranes from blends of sulfonated poly(phenylene sulfide) and sulfonated phenolphthalein poly(ether ether ketone)

A series of semihomogeneous cation‐exchange membranes were prepared with binary blend systems, such as sulfonated phenolphthalein poly(ether ether ketone) (SPEEK‐C)/sulfonated poly(phenylene sulfide) (SPPS), or ternary blend systems, such as phenolphthalein poly(ether ether ketone) (PEEK‐C)/SPEEK‐C/SPPS, by solution blending and phase inversion, in which PEEK‐C and SPEEK‐C acted as binders and SPPS powder acted as a polyelectrolyte. Compared with homogeneous and heterogeneous membranes, the prepared semihomogeneous membranes had good electrochemical properties and mechanical strength as well as good dimensional stability. The fundamental properties of the membranes, such as the ion‐exchange capacity, water content, electrical resistance, transport number, diffusion coefficient of the electrolytes, and streaming potential, were largely dependent on both the loading of the SPPS resin and the sulfonation degree of PEEK‐C. Through the adjustment of these two important parameters, a series of semihomogeneous membranes with the desired conductivity and selectivity and the proper water content for different industrial purposes, such as electrodialysis, diffusional dialysis, and proton exchange, were achieved. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 1478–1485, 2004     

Phthalonitrile end-capped sulfonated polyarylene ether nitriles for low-swelling proton exchange membranes

A series of phthalonitrile end-capped sulfonated polyarylene ether nitriles are synthesized via K₂CO₃ mediated nucleophilic aromatic substitution reaction at various molar ratios. The as-prepared polymer structures are confirmed by ¹H NMR and FTIR spectroscopy. The properties of membranes cast from the corresponding polymers are investigated with respect to their structures. The membranes exhibit good thermal and mechanical properties, low methanol permeability (0.01?×?10^?6–0.58?×?10^?6 cm²·s^?1 at 20 °C), and high proton conductivity (0.021–0.088 S·cm^?1 at 20 °C). The introduction of phthalonitrile is proved to increase intermolecular interaction, mainly contributing to the reduction in water uptake, swelling ratio, and methanol permeability. More importantly, its introduction does not decrease the proton conductivity, but there is a slight increase. Furthermore, the selectivity of SPEN-CN-50 can reach 4.11?×?10⁵ S·s·cm^?3, which is about nine times higher than that of Nafion 117. All the data show that the as-prepared membranes may be potential proton exchange membrane for DMFCs applications.     

Novel amphoteric ion exchange membranes by blending sulfonated poly(ether ether ketone) with ammonium polyphosphate for vanadium redox flow battery applications

A novel amphoteric ion exchange membrane for vanadium redox flow battery (VRFB) was explored by blending sulfonated poly(ether ether ketone) (SPEEK) and ammonium polyphosphate (APP). The high-stability flame retardant of cross-linked APP with a large number of NH₄⁺ groups was first introduced into SPEEK membrane. It was observed that the addition of APP with special structure could achieve a good balance between proton conductivity and vanadium ions permeability. The abundant NH₄⁺ in APP could block the penetration of vanadium ions by Donnan/Manning exclusion effect and ionic crossing networks due to the ionic bonds between cation and anion groups, and specially a small amount of APP within 5% could remarkably improve the proton conductivity of pristine SPEEK membrane might be ascribed to the unique fast proton transport channels formed by hydrogen bond networks and particular micro-phase separation as a result of interaction between SPEEK and APP. When 5% APP was blended, the SPEEK/APP-5% (S/APP-5%) amphoteric membrane showed a higher selectivity of 20.87 × 10⁴ S min/cm³ (with a good proton conductivity of 0.075 S/cm and a lower VO²⁺ permeability of 3.45 × 10⁻⁷ cm²/ min) and presented better thermal and chemical stability compared to Nafion115 and SPEEK membranes. The VRFB single cell assembled with S/APP-5% amphoteric membrane exhibited more excellent performance than that of Nafion115 and pristine SPEEK membranes, which revealed a higher coulombic efficiency of 96.3%–98.3%, comparable voltage efficiency of 88.4%–78.7% and higher energy efficiency of 85.1%–77.4% from 40 to 80 mA/cm², respectively, and showed relatively good stability of the efficiency up to 50 cycles at 60 mA/cm². The results demonstrated that the designed S/APP amphiprotic membrane of outstanding selectivity, high battery efficiency, and good durability is a prospected VRFB separator.     

Sulfonated poly(ether ketone ketone) ionomers as proton exchange membranes

Sulfonated poly(ether ketone ketone) ionomers (SPEKK) with ion‐exchange capacities (IEC) between 0.2 and 3.4 meq/g were prepared by sulfonating PEKK with a mixture of concentrated and fuming sulfuric acids. Sulfonation occurs only on the phenyl rings attached to ether and ketone groups. The glass transition temperature of the dry SPEKK ionomers increased linearly with increasing IEC, and the ionomers were thermally stable to ～250°C, above which desulfonation occurred. Water‐swollen ionomers exhibited microphase separated morphologies, and the average correlation length determined by small angle X‐ray scattering increased with increasing IEC. The proton conductivity of hydrated SPEKK membranes measured by impedance spectroscopy ranged from ～10^–3 to 10^–1 S/cm as the IEC increased from ～1.0 to 2.4 meq/g. Single cell performance curves on membrane‐electrode assemblies (MEA) indicated that the SPEKK membranes approached the performance of Nafion? for an IEC of 2 meq/g. POLYM. ENG. SCI., 45:1081–1091, 2005. © 2005 Society of Plastics Engineers     

Modified Sulfonated Poly(ether ether ketone) Based Mixed Matrix Membranes for Direct Methanol Fuel Cells

Mixed matrix membranes based on zeolite 4A‐methane sulfonic acid (MSA)‐sulfonated poly(ether ether ketone) (SPEEK) are evaluated as a potential polymer electrolyte membrane (PEM) for direct methanol fuel cells (DMFCs). Ion‐exchange capacity, sorption of water, and water–methanol mixture, proton conductivity, and methanol permeability for the mixed‐matrix membranes have been extensively investigated. The mixed‐matrix membranes are also characterized for their cross‐sectional morphology, mechanical, and thermal properties. DMFCs employing SPEEK‐MSA (20 wt.%) blend, zeolite 4A (4 wt.%)‐SPEEK‐MSA (20 wt.%) mixed matrix membranes deliver peak power densities of 130 and 159 mW cm^–2, respectively; while a peak power density of only 95 mW cm^–2 is obtained for the DMFC employing pristine SPEEK membrane at 70 °C. The results showed that these SPEEK based mixed matrix membranes exhibit higher DMFC performance and lower methanol permeability in comparison to Nafion‐117 membrane.     

Preparation of highly H+ permeable sulfonated poly(ether ether ketone) cation exchange membranes and their applications in electro‐generation of thioglycolic acid

BACKGROUND: Sulfonated poly(ether ether ketone) (SPEEK) was successfully synthesized from sulfonated 4,4′‐difluorobenzophenone, 4,4′‐difluorobenzophenone and bisphenol A. SPEEK cation exchange membranes were prepared by the casting method. The composition and morphology of SPEEK were characterized using Fourier transform infrared and ¹H NMR spectroscopies, respectively. The ion exchange capacity (IEC), water uptake and degree of swelling of the membranes were also investigated. SPEEK120 was used as a separator in an electrolysis cell to produce thioglycolic acid (TGA). RESULTS: SPEEK polymerization was carried out at 145 and 175 °C for 10 h. The IEC of the SPEEK membranes was measured as 0.24–2.02 meq g^?1 and the water uptake as 2.26–26.45%. The degree of swelling of the membranes was 1.71–15.28%. TGA was effectively prepared by electro‐reduction of dithioglycolic acid. The current efficiency peaked at 58.31% at room temperature with a current density of 15 mA cm^?2. CONCLUSION: SPEEK120 membrane shows good dimensional stability and H⁺ permeability. Compared to the traditional metal‐reduction method, the current electro‐reduction technique avoids the use of zinc powder and so reduces environmental pollution. Copyright © 2009 Society of Chemical Industry     

Nanostructure and properties of proton‐conducting sulfonated poly(ether ether ketone) (SPEEK) and zirconia–SPEEK hybrid membranes for direct alcohol fuel cells: effect of the nature of swelling solvent and incorporation of heteropolyacid

The influence, on membrane nanostructure and properties, of water or ethanol as swelling solvent of sulfonated poly(ether ether ketone) (SPEEK) and zirconia–SPEEK hybrid membranes prepared using the sol–gel process has been investigated. Independent of the solvent, small‐angle X‐ray scattering measurements reveal the existence of a two‐level hierarchical structure in SPEEK of greater sulfonation level, consisting of solvent‐swelled spatially correlated primary SO₃H‐rich ionic clusters of around 15 Å in size, forming larger secondary aggregates well dispersed in the PEEK matrix. The size of the primary nanodomains and the connectivity between domains are determining parameters for protonic conductivity, solvent swelling ability and permeability of the membranes. For both SPEEK and zirconia–SPEEK membranes containing ethanol, the pronounced affinity of ethanol molecules with SPEEK leads to an increase in the size of ionic clusters and of the number of connecting channels between clusters compared to membranes containing water. This promotes solvent swelling and proton conductivity. The increase in permeability to water induced by incorporation of ethanol in place of water in both polymeric and hybrid membranes is less in the hybrid membranes. This result suggests that the potential use of zirconia–SPEEK hybrid membranes in direct alcohol fuel cells is more promising than that of pure SPEEK, due not only to the less probable alcohol and water penetration in the membranes associated with their lower permeability, but also to the fact that an eventual penetration of alcohol in hybrid membranes should reduce the risk of cathode flooding compared to zirconia‐free SPEEK membranes. Copyright © 2011 Society of Chemical Industry     

Synthesis and characterization of homogeneously sulfonated poly(ether ether ketone) membranes: Effect of casting solvent

Poly(ether ether ketone) (PEEK) was homogeneously sulfonated to have various degrees of sulfonation from 48 to 83%. The sulfonated PEEK (sPEEK) membranes were prepared by a solvent casting method using a few solvents such as N,N‐dimethyl formamide, N,N‐dimethyl acetamide, and 1‐methyl‐2‐pyrrolidinone. The effect of casting solvent on the membrane morphology and properties was investigated. The sulfonation degree and ion exchange capacity were determined by a back titration method, and the morphology of membrane by SEM. It has been demonstrated that the surface morphology and properties of sPEEK membranes, such as water uptake, methanol permeability, ion conductivity, and mechanical strength, were considerably affected by the type of solvent, where the DMAC‐sPEEK system showed the best performance in the polymer electrolyte membrane application for DMFC. This solvent effect on the membrane morphology and properties was caused by interaction strength (hydrogen bonding) between polymer and solvent. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008