A Thiophene‐Based Anchoring Ligand and Its Heteroleptic Ru(II)‐Complex for Efficient Thin‐Film Dye‐Sensitized Solar Cells

A novel heteroleptic Ru^II complex (BTC‐2) employing 5,5′‐(2,2′‐bipyridine‐4,4′‐diyl)‐bis(thiophene‐2‐carboxylic acid) (BTC) as the anchoring group and 4,4′‐ dinonyl‐2,2′‐bipiridyl and two thiocyanates as ligands is prepared. The photovoltaic performance and device stability achieved with this sensitizer are compared to those of the Z‐907 dye, which lacks the thiophene moieties. For thin mesoporous TiO₂ films, the devices with BTC‐2 achieve higher power conversion efficiencies than those of Z‐907 but with a double‐layer thicker film the device performance is similar. Using a volatile electrolyte and a double layer 7 + 5 μm mesoporous TiO₂ film, BTC‐2 achieves a solar‐to‐electricity conversion efficiency of 9.1% under standard global AM 1.5 sunlight. Using this sensitizer in combination with a low volatile electrolyte, a photovoltaic efficiency of 8.3% is obtained under standard global AM 1.5 sunlight. These devices show excellent stability when subjected to light soaking at 60 °C for 1000 h. Electrochemical impedance spectroscopy and transient photovoltage decay measurements are performed to help understand the changes in the photovoltaic parameters during the aging process. In solid state dye‐sensitized solar cells (DSSCs) using an organic hole‐transporting material (spiro‐MeOTAD, 2,2′,7,7′‐tetrakis‐(N,N‐di‐p‐methoxyphenylamine)‐9,9′‐spirobifluorene), the BTC‐2 sensitizer exhibits an overall power conversion efficiency of 3.6% under AM 1.5 solar (100 mW cm^?2) irradiation.     

Enhanced‐Light‐Harvesting Amphiphilic Ruthenium Dye for Efficient Solid‐State Dye‐Sensitized Solar Cells

A ruthenium sensitizer (coded C101, NaRu (4,4′‐bis(5‐hexylthiophen‐2‐yl)‐2,2′‐bipyridine) (4‐carboxylic acid‐4′‐caboxylate‐2,2′‐bipyridine) (NCS)₂) containing a hexylthiophene‐conjugated bipyridyl group as an ancillary ligand is presented for use in solid‐state dye‐sensitized solar cells (SSDSCs). The high molar‐extinction coefficient of this dye is advantageous compared to the widely used Z907 dye, (NaRu (4‐carboxylic acid‐4′‐carboxylate) (4,4′‐dinonyl‐2,2′‐bipyridine) (NCS)₂). In combination with an organic hole‐transporting material (spiro‐MeOTAD, 2,2′,7,7′‐tetrakis‐(N,N‐di‐p‐methoxyphenylamine) 9, 9′‐spirobifluorene), the C101 sensitizer exhibits an excellent power‐conversion efficiency of 4.5% under AM 1.5 solar (100 mW cm^?2) irradiation in a SSDSC. From electronic‐absorption, transient‐photovoltage‐decay, and impedance measurements it is inferred that extending the π‐conjugation of spectator ligands induces an enhanced light harvesting and retards the charge recombination, thus favoring the photovoltaic performance of a SSDSC.     

Polyfluorene Derivatives are High‐Performance Organic Hole‐Transporting Materials for Inorganic−Organic Hybrid Perovskite Solar Cells

Photovoltaics based on organic?inorganic perovskites offer new promise to address the contemporary energy and environmental issues. These solar cells have so far largely relied on small‐molecule hole transport materials such as spiro‐OMeTAD, which commonly suffer from high cost and low mobility. In principle, polyfluorene copolymers can be an ideal alternative to spiro‐OMeTAD, given their low price, high hole mobility and good processability, but this potential has not been explored. Herein, polyfluorene derived polymers‐TFB and PFB, which contain fluorine and arylamine groups, are demonstrated and can indeed rival or even outperform spiro‐OMeTAD as efficient hole‐conducting materials for perovskite solar cells. In particular, under the one‐step perovskite deposition condition, TFB achieves a 10.92% power conversion efficiency that is considerably higher than that with spiro‐OMeTAD (9.78%), while using the two‐step perovskite deposition method, about 13% efficient solar cells with TFB (12.80%) and spiro‐OMeTAD (13.58%) are delivered. Photo­luminescence reveals the efficient hole extraction and diffusion at the interface between CH₃NH₃PbI₃ and the hole conducting polymer. Impedance spectroscopy uncovers the higher electrical conductivity and lower series resistance than spiro‐OMeTAD, accounting for the significantly higher fill factor, photocurrent and open‐circuit voltage of the TFB‐derived cells than with spiro‐MeOTAD.     

Influence of Ion Induced Local Coulomb Field and Polarity on Charge Generation and Efficiency in Poly(3‐Hexylthiophene)‐Based Solid‐State Dye‐Sensitized Solar Cells

Dye‐sensitized solar cells (DSSC) are a realistic option for converting light to electrical energy. Hybrid architectures offer a vast materials library for device optimization, including a variety of metal oxides, organic and inorganic sensitizers, molecular, polymeric and electrolytic hole‐transporter materials. In order to further improve the efficiency of solid‐state dye‐sensitized solar cells, recent attention has focused on using light absorbing polymers such as poly(3‐hexylthiophene) (P3HT), to replace the more commonly used “transparent” 2,2′,7,7′‐tetrakis‐(N,N‐di‐p‐methoxyphenyl‐amine)9,9′spiro‐bifluorene (spiro‐OMeTAD), in order to enhance the light absorption within thin films. As is the case with spiro‐OMeTAD based solid‐state DSSC, the P3HT‐based devices improve significantly with the addition of lithium bis(trifluoromethylsulfonyl)imide salts (Li‐TFSI), although the precise role of these additives has not yet been clarified in solid‐state DSCs. Here, we present a thorough study on the effect of Li‐TFSI in P3HT based solid‐state DSSC incorporating an indolene‐based organic sensitizer termed D102. Employing ultrafast transient absorption and cw‐emission spectroscopy together with electronic measurements, we demonstrate a fine tuning of the energetic landscape of the active cell components by the local Coulomb field induced by the ions. This increases the charge transfer nature of the excited state on the dye, significantly accelerating electron injection into the TiO₂. We demonstrate that this ionic influence on the excited state energy is the primary reason for enhanced charge generation with the addition of ionic additives. The deepening of the relative position of the TiO₂ conduction band, which has previously been thought to be the cause for enhanced charge generation in dye sensitized solar cells with the addition of lithium salts, appears to be of minor importance in this system.     

Highly Efficient Solid‐State Dye‐Sensitized Solar Cells Based on Triphenylamine Dyes

Two triphenylamine‐based metal‐free organic sensitizers, D35 with a single anchor group and M14 with two anchor groups, have been applied in dye‐sensitized solar cells (DSCs) with a solid hole transporting material or liquid iodide/triiodide based electrolyte. Using the molecular hole conductor 2,2',7,7'‐tetrakis‐(N,N‐di‐p‐methoxyphenyl‐amine)9,9'‐spirobifluorene (spiro‐OMeTAD), good overall conversion efficiencies of 4.5% for D35 and 4.4% for M14 were obtained under standard AM 1.5G illumination (100 mW cm^?2). Although M14 has a higher molar extinction coefficient (by ～ 60%) and a slightly broader absorption spectrum compared to D35 , the latter performs slightly better due to longer lifetime of electrons in the TiO₂, which can be attributed to differences in the molecular structure. In iodide/triiodide electrolyte‐based DSCs, D35 outperforms M14 to a much greater extent, due to a very large increase in electron lifetime. This can be explained by both the greater blocking capability of the D35 monolayer and the smaller degree of interaction of triiodide (iodine) with D35 compared to M14 . The present work gives some insight into how the molecular structure of sensitizer affects the performance in solid‐state and iodide/triiodide‐based DSCs.     

PbS and CdS Quantum Dot‐Sensitized Solid‐State Solar Cells: “Old Concepts,New Results”

Lead sulfide (PbS) and cadmium sulfide (CdS) quantum dots (QDs) are prepared over mesoporous TiO₂ films by a successive ionic layer adsorption and reaction (SILAR) process. These QDs are exploited as a sensitizer in solid‐state solar cells with 2,2′,7,7′‐tetrakis(N,N‐di‐p‐methoxyphenylamine)‐9,9′‐spirobifluorene (spiro‐OMeTAD) as a hole conductor. High‐resolution transmission electron microscopy (TEM) images reveal that PbS QDs of around 3 nm in size are distributed homogeneously over the TiO₂ surface and are well separated from each other if prepared under common SILAR deposition conditions. The pore size of the TiO₂ films and the deposition medium are found to be very critical in determining the overall performance of the solid‐state QD cells. By incorporating promising inorganic QDs (PbS) and an organic hole conductor spiro‐OMeTAD into the solid‐state cells, it is possible to attain an efficiency of over 1% for PbS‐sensitized solid‐state cells after some optimizations. The optimized deposition cycle of the SILAR process for PbS QDs has also been confirmed by transient spectroscopic studies on the hole generation of spiro‐OMeTAD. In addition, it is established that the PbS QD layer plays a role in mediating the interfacial recombination between the spiro‐OMeTAD⁺ cation and the TiO₂ conduction band electron, and that the lifetime of these species can change by around 2 orders of magnitude by varying the number of SILAR cycles used. When a near infrared (NIR)‐absorbing zinc carboxyphthalocyanine dye (TT1) is added on top of the PbS‐sensitized electrode to obtain a panchromatic response, two signals from each component are observed, which results in an improved efficiency. In particular, when a CdS‐sensitized electrode is first prepared, and then co‐sensitized with a squarine dye (SQ1), the resulting color change is clearly an addition of each component and the overall efficiencies are also added in a more synergistic way than those in PbS/TT1‐modified cells because of favorable charge‐transfer energetics.     

Dependence of Dye Regeneration and Charge Collection on the Pore‐Filling Fraction in Solid‐State Dye‐Sensitized Solar Cells

Solid‐state dye‐sensitized solar cells rely on effective infiltration of a solid‐state hole‐transporting material into the pores of a nanoporous TiO₂ network to allow for dye regeneration and hole extraction. Using microsecond transient absorption spectroscopy and femtosecond photoluminescence upconversion spectroscopy, the hole‐transfer yield from the dye to the hole‐transporting material 2,2′,7,7′‐tetrakis(N,N‐di‐p‐methoxyphenylamine)‐9,9'‐spirobifluorene (spiro‐OMeTAD) is shown to rise rapidly with higher pore‐filling fractions as the dye‐coated pore surface is increasingly covered with hole‐transporting material. Once a pore‐filling fraction of ≈30% is reached, further increases do not significantly change the hole‐transfer yield. Using simple models of infiltration of spiro‐OMeTAD into the TiO₂ porous network, it is shown that this pore‐filling fraction is less than the amount required to cover the dye surface with at least a single layer of hole‐transporting material, suggesting that charge diffusion through the dye monolayer network precedes transfer to the hole‐transporting material. Comparison of these results with device parameters shows that improvements of the power‐conversion efficiency beyond ≈30% pore filling are not caused by a higher hole‐transfer yield, but by a higher charge‐collection efficiency, which is found to occur in steps. The observed sharp onsets in photocurrent and power‐conversion efficiencies with increasing pore‐filling fraction correlate well with percolation theory, predicting the points of cohesive pathway formation in successive spiro‐OMeTAD layers adhered to the pore walls. From percolation theory it is predicted that, for standard mesoporous TiO₂ with 20 nm pore size, the photocurrent should show no further improvement beyond an ≈83% pore‐filling fraction.     

Diphenylamine‐Substituted Carbazole‐Based Hole Transporting Materials for Perovskite Solar Cells: Influence of Isomeric Derivatives

A series of new branched hole transporting materials (HTMs) containing two diphenylamine‐substituted carbazole fragments linked by a nonconjugated methylenebenzene unit is synthesized and tested in perovskite solar cells. Synthesis of the investigated materials is performed by a simple two‐step synthetic procedure providing a target product in high yield. The isolated materials demonstrate good thermal stability and majority of the investigated compounds exist in an amorphous state, which is advantageous as there is no risk of crystallization directly in the film. The highest charge drift mobility of µ₀ = 4 × 10^?4 cm² V^?1 s^?1, measured at weak electric fields, is by ca. one order of magnitude higher than that of Spiro‐OMeTAD under identical conditions. From the perovskite solar cell testing results, it can be seen that performance of two new HTMs ( V885 and V911 ) is on a par with Spiro‐OMeTAD. Due to the ease of synthesis, good thermal, optical and photophysical properties, this type of molecules hold great promise for practical application in commercial perovskite solar cells.     

Novel Conjugated Organic Dyes for Efficient Dye‐Sensitized Solar Cells

Novel conjugated organic dyes that have N,N‐dimethylaniline (DMA) moieties as the electron donor and a cyanoacetic acid (CAA) moiety as the electron acceptor were developed for use in dye‐sensitized nanocrystalline‐TiO₂ solar cells (DSSCs). We attained a maximum solar‐energy‐to‐electricity conversion efficiency (η) of 6.8 % under AM 1.5 irradiation (100 mW cm^–2) with a DSSC based on 2‐cyano‐7,7‐bis(4‐dimethylamino‐phenyl)hepta‐2,4,6‐trienoic acid (NKX‐2569): short‐circuit photocurrent density (J_sc) = 12.9 mA cm^–2, open‐circuit voltage (V_oc) = 0.71 V, and fill factor (ff) = 0.74. The high performance of the solar cells indicated that highly efficient electron injection from the excited dyes to the conduction band of TiO₂ occurred. The experimental and calculated Fourier‐transform infrared (FT‐IR) absorption spectra clearly showed that these dyes were adsorbed on the TiO₂ surface with the carboxylate coordination form. A molecular‐orbital calculation indicated that the electron distribution moved from the DMA moiety to the CAA moiety by photoexcitation of the dye.     

Highly Efficient Quantum‐Dot‐Sensitized Solar Cell Based on Co‐Sensitization of CdS/CdSe

Cadmium sulfide (CdS) and cadmium selenide (CdSe) quantum dots (QDs) are sequentially assembled onto a nanocrystalline TiO₂ film to prepare a CdS/CdSe co‐sensitized photoelectrode for QD‐sensitized solar cell application. The results show that CdS and CdSe QDs have a complementary effect in the light harvest and the performance of a QDs co‐sensitized solar cell is strongly dependent on the order of CdS and CdSe respected to the TiO₂. In the cascade structure of TiO₂/CdS/CdSe electrode, the re‐organization of energy levels between CdS and CdSe forms a stepwise structure of band‐edge levels which is advantageous to the electron injection and hole‐recovery of CdS and CdSe QDs. An energy conversion efficiency of 4.22% is achieved using a TiO₂/CdS/CdSe/ZnS electrode, under the illumination of one sun (AM1.5,100 mW cm^?2). This efficiency is relatively higher than other QD‐sensitized solar cells previously reported in the literature.     

New Family of Ruthenium‐Dye‐ Sensitized Nanocrystalline TiO2 Solar Cells with a High Solar‐Energy‐Conversion Efficiency

A new type of ruthenium complexes 6 – 8 with tridentate bipyridine–pyrazolate ancillary ligands has been synthesized in an attempt to elongate the π‐conjugated system as well as to increase the optical extinction coefficient, possible dye uptake on TiO₂, and photostability. Structural characterization, photophysical studies, and corresponding theoretical approaches have been made to ensure their fundamental basis. As for dye‐sensitized solar cell applications, it was found that 6 – 8 possess a larger dye uptake of 2.4 × 10^–7 mol cm^–2, 1.5 × 10^–7 mol cm^–2, and 1.3 × 10^–7 mol cm^–2, respectively, on TiO₂ than that of the commercial N3 dye (1.1 × 10^–7 mol cm^–2). Compound 8 works as a highly efficient photosensitizer for the dye‐sensitized nanocrystalline TiO₂ solar cell, producing a 5.65 % solar‐light‐to‐electricity conversion efficiency (compare with 6.01 % for N3 in this study), a short‐circuit current density of 15.6 mA cm^–2, an open‐circuit photovoltage of 0.64 V, and a fill factor of 0.57 under standard AM 1.5 irradiation (100 mW cm^–2). These, in combination with its superior thermal and light‐soaking stability, lead to the conclusion that the concomitant tridentate binding properties offered by the bipyridine‐pyrazolate ligand render a more stable complexation, such that extended life spans of DSSCs may be expected.     

Hierarchical Double‐Shell Nanostructures of TiO2 Nanosheets on SnO2 Hollow Spheres for High‐Efficiency,Solid‐State,Dye‐Sensitized Solar Cells

A high‐energy conversion efficiency of 8.2% at 100 mW cm^?2 is reported, one of the highest values for N719‐based, solid‐state, dye‐sensitized solar cells (ssDSSCs). The solar cells are based on hierarchical double‐shell nanostructures consisting of inner SnO₂ hollow spheres (SHS) surrounded by outer TiO₂ nanosheets (TNSs). Deposition of the TNS on the SHS outer surface is performed via solvothermal reactions in order to generate a double‐shell SHS@TNS nanostructure that provides a large surface area and suppresses recombination of photogenerated electrons. An organized mesoporous (OM)‐TiO₂ film with high porosity, large pores, and good interconnectivity is also prepared via a sol‐gel process using a poly(vinyl chloride)‐g‐poly(oxyethylene methacrylate) (PVC‐g‐POEM) graft copolymer template. This film is utilized as a matrix to disperse the double‐shell nanostructures. Such nanostructures provide good pore‐filling for solid polymer electrolytes, faster electron transfer, and enhanced light scattering, as confirmed by reflectance spectroscopy, incident photon‐to‐electron conversion efficiency (IPCE), and intensity‐modulated photocurrent spectroscopy (IMPS)/intensity‐modulated photovoltage spectroscopy (IMVS).     

Design of Multilayered Nanostructures and Donor–Acceptor Interfaces in Solution‐Processed Thin‐Film Organic Solar Cells

Multilayered polymer thin‐film solar cells have been fabricated by wet processes such as spin‐coating and layer‐by‐layer deposition. Hole‐ and electron‐transporting layers were prepared by spin‐coating with poly(3,4‐ethylenedioxythiophene) oxidized with poly(4‐styrenesulfonate) (PEDOT:PSS) and fullerene (C₆₀), respectively. The light‐harvesting layer of poly‐(p‐phenylenevinylene) (PPV) was fabricated by layer‐by‐layer deposition of the PPV precursor cation and poly(sodium 4‐styrenesulfonate) (PSS). The layer‐by‐layer technique enables us to control the layer thickness with nanometer precision and select the interfacial material at the donor–acceptor heterojunction. Optimizing the layered nanostructures, we obtained the best‐performance device with a triple‐layered structure of PEDOT:PSS|PPV|C₆₀, where the thickness of the PPV layer was 11 nm, comparable to the diffusion length of the PPV singlet exciton. The external quantum efficiency spectrum was maximum (ca. 20%) around the absorption peak of PPV and the internal quantum efficiency was estimated to be as high as ca. 50% from a saturated photocurrent at a reverse bias of ?3 V. The power conversion efficiency of the triple‐layer solar cell was 0.26% under AM1.5G simulated solar illumination with 100 mW cm^?2 in air.     

Dithieno[3,2‐b:2′,3′‐d]pyrrol‐Cored Hole Transport Material Enabling Over 21% Efficiency Dopant‐Free Perovskite Solar Cells

Dopant‐free hole transport materials (HTMs) are essential for commercialization of perovskite solar cells (PSCs). However, power conversion efficiencies (PCEs) of the state‐of‐the‐art PSCs with small molecule dopant‐free HTMs are below 20%. Herein, a simple dithieno[3,2‐b:2′,3′‐d]pyrrol‐cored small molecule, DTP‐C6Th, is reported as a promising dopant‐free HTM. Compared with commonly used spiro‐OMeTAD, DTP‐C6Th exhibits a similar energy level, a better hole mobility of 4.18 × 10^?4 cm² V^?1 s^?1, and more efficient hole extraction, enabling efficient and stable PSCs with a dopant‐free HTM. With the addition of an ultrathin poly(methyl methacrylate) passivation layer and properly tuning the composition of the perovskite absorber layer, a champion PCE of 21.04% is achieved, which is the highest value for small molecule dopant‐free HTM based PSCs to date. Additionally, PSCs using the DTP‐C6Th HTM exhibit significantly improved long‐term stability compared with the conventional cells with the metal additive doped spiro‐OMeTAD HTM. Therefore, this work provides a new candidate and effective device engineering strategy for achieving high PCEs with dopant‐free HTMs.     

Novel Nano‐Structured Silica‐Based Electrolytes Containing Quaternary Ammonium Iodide Moieties

A series of new hybrid organic‐inorganic molecules were prepared either by grafting of aminopropyltriethoxysilane (APTS) on silica nanoparticles followed by quaternarization of the nitrogen with ethyl, heptyl and isopropyl iodides or by grafting of N,N,N‐triethyl‐3‐(triethoxysilyl)propan‐1‐aminium iodide and N,N,N‐tridodecyl‐3‐(triethoxysilyl)propan‐1‐aminium iodide onto the silica nanoparticles. These new materials were used as iodide sources in the preparation of electrolyte solutions for dye‐sensitized solar cells (DSSCs). The performance of DSSCs was studied as a function of the nature of the solvent, the nature of the dye, the concentration of the modified silica in the electrolyte system and the silica content introduced during the hybrid synthesis. An efficiency of 8.5 % was obtained for solar cells containing the triethyl ammonium iodide salt at a concentration of 1 M in either acetonitrile (AN) or 3‐methoxypropionitrile (MPN) under an illumination of 10 mW cm^–2, the equivalent of 0.1 Sun at AM 1.5G. At 1 Sun (100 mW cm^–2, efficiencies of 6.6 % and 5.1 % were recorded for the AN and MPN‐based electrolytes, respectively.     

The 2,2,6,6‐Tetramethyl‐1‐piperidinyloxy Radical: An Efficient,Iodine‐ Free Redox Mediator for Dye‐Sensitized Solar Cells

A promising redox system, offering an alternative to the widely used iodide/triiodide couple, based on the stable organic radical 2,2,6,6‐tetramethyl‐1‐piperidinyloxy (TEMPO) has been employed in dye‐sensitized solar cells. The photovoltaic performance of this new redox couple has been evaluated by employing nanocrystalline TiO₂ films with different thickness. Judicious selections of a 5.0 μm photoanode made from TiO₂ mesoscopic particles and an organic sensitizer with a high molar extinction coefficient yield an overall solar‐to‐electric power conversion efficiency of 5.4 % under AM 1.5 illumination at 100 mW cm^–2, which is unprecedented for an iodine‐free mediator system.     

Amorphous Zinc Stannate (Zn2SnO4) Nanofibers Networks as Photoelectrodes for Organic Dye‐Sensitized Solar Cells

A new strategy for developing dye‐sensitised solar cells (DSSCs) by combining thin porous zinc tin oxide (Zn₂SnO₄) fiber‐based photoelectrodes with purely organic sensitizers is presented. The preparation of highly porous Zn₂SnO₄ electrodes, which show high specific surface area up to 124 m²/g using electrospinning techniques, is reported. The synthesis of a new organic donor‐conjugate‐acceptor (D‐π‐A) structured orange organic dye with molar extinction coefficient of 44 600 M^?1 cm^?1 is also presented. This dye and two other reference dyes, one organic and a ruthenium complex, are employed for the fabrication of Zn₂SnO₄ fiber‐based DSSCs. Remarkably, organic dye‐sensitized DSSCs displayed significantly improved performance compared to the ruthenium complex sensitized DSSCs. The devices based on a 3 μm‐thick Zn₂SnO₄ electrode using the new sensitizer in conjunction with a liquid electrolyte show promising photovoltaic conversion up to 3.7% under standard AM 1.5G sunlight (100 mW cm^?2). This result ranks among the highest reported for devices using ternary metal oxide electrodes.     

Enhanced Light‐Harvesting Capability of a Panchromatic Ru(II) Sensitizer Based on π‐Extended Terpyridine with a 4‐Methylstylryl Group for Dye‐Sensitized Solar Cells

A novel Ru π‐expanded terpyridyl sensitizer, referred to as HIS‐2, is prepared based on the molecular design strategy of substitution with a moderately electron‐donating 4‐methylstyryl group onto the terpyridyl ligand. The HIS‐2 dye exhibits a slightly increased metal‐to‐ligand charge transfer (MLCT) absorption at around 600 nm and an intense π–π* absorption in the UV region compared with a black dye. Density functional theory calculations reveal that the lowest unoccupied molecular orbital (LUMO) is distributed over the terpyridine and 4‐methylstyryl moieties, which enhances the light‐harvesting capability and is appropriate for smooth electron injection from the dye to the TiO₂ conduction band. The incident photon‐to‐electricity conversion efficiency spectrum of HIS‐2 exhibits better photoresponse compared with black dye over the whole spectral region as a result of the extended π‐conjugation. A DSC device based on black dye gives a short‐circuit current (J_SC) of 21.28 mA cm^?2, open‐circuit voltage (V_OC) of 0.69 V, and fill factor (FF) of 0.72, in an overall conversion efficiency (η) of 10.5%. In contrast, an HIS‐2 based cell gives a higher J_SC value of 23.07 mA cm^?2 with V_OC of 0.68 V, and FF of 0.71, and owing to the higher J_SC value of HIS‐2, an improved η value of 11.1% is achieved.     

High Efficiency Planar p‐i‐n Perovskite Solar Cells Using Low‐Cost Fluorene‐Based Hole Transporting Material

For commercial applications, it is a challenge to find suitable and low‐cost hole‐transporting material (HTM) in perovskite solar cells (PSCs), where high efficiency spiro‐OMeTAD and PTAA are expensive. A HTM based on 9,9‐dihexyl‐9H‐fluorene and N,N‐di‐p‐methylthiophenylamine (denoted as FMT) is designed and synthesized. High‐yield FMT with a linear structure is synthesized in two steps. The dopant‐free FMT‐based planar p‐i‐n perovskite solar cells (pp‐PSCs) exhibit a high power conversion efficiency (PCE) of 19.06%, which is among the highest PCEs reported for the pp‐PSCs based on organic HTM. For comparison, a PEDOT:PSS HTM‐based pp‐PSC is fabricated under the same conditions, and its PCE is found to be 13.9%.     

Improving the Photovoltage of Dithienopyrrole Dye‐Sensitized Solar Cells via Attaching the Bulky Bis(octyloxy)biphenyl Moiety to the Conjugated π‐Linker

The judicious design of 3D giant organic dye molecules to enable the formation of a porous photoactive layer on the surface of titania is one of the viable tactics to abate the adverse interfacial charge recombination in dye‐sensitized solar cells (DSCs) employing outer‐sphere redox couples. Here 2′,6′‐bis(octyloxy)‐biphenyl substituted dithieno[3,2‐b:2′,3′‐d]pyrrole segment is constructed and employed as the π‐linker of a high molar absorption coefficient organic push‐pull dye. With respect to its congener possessing the hexyl substituted dithieno[3,2‐b:2′,3′‐d]pyrrole linker, the new dye can self‐assemble on the surface of titania to afford a porous organic coating, which effectively slow down the kinetics of charge recombination of titania electrons with both outer‐sphere tris(1,10‐phenanthroline)cobalt(III) ions and photooxidized dye molecules, improving the cell photovoltage. In addition, the diminishments of charge recombination via modulating the microstructure of interfacial functional zone can also overcompensate the disadvantageous impact of reduced light‐harvesting and evoke an enhanced photocurrent output, bringing forth an efficiency improvement from 7.5% to 9.3% at the 100 mW cm^?2, simulated AM1.5 conditions.