Synthesis and characterization of functionalized syndiotactic polystyrene copolymers

Functionalized syndiotactic polystyrene copolymers were synthesized and characterized. The syndiotactic polystyrene copolymers, poly(styrene‐co‐4‐methylstyrene) (sPSMS), were prepared by styrene with 4‐methylstyrene with a metallocene/methylaluminoxane catalyst. In addition, grafted copolymers, chemically grafted with isoprene onto an sPSMS backbone [poly(styrene‐co‐4‐methylstyrene)‐g‐polyisoprene (sPSMS‐g‐PIP)] were synthesized by anionic grafting polymerization with a metallation reagent. In this study, we also examined the effect of the degree of functionalization (epoxidation) on the polymer structure of the sPSMS‐g‐PIP copolymers. Experimental results indicate that the crystallinity of the sPSMS‐g‐PIP copolymer was lower than that of the ungrafted sPSMS copolymer. Moreover, the epoxy‐containing sPSMS‐g‐PIP copolymer effectively increased the thermal stability more than did the sPSMS‐g‐PIP copolymer alone. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 1038–1045, 2002     

Selective separation of water from aqueous alcohol mixtures through functionalized syndiotactic poly(styrene‐co‐4‐methylstyrene) membranes by pervaporation

The pervaporation performances of a series of functionalized syndiotactic poly(styrene‐co‐4‐methylstyrene) (SPSM) membranes for various alcohol mixtures were investigated. The syndiotactic polystyrene copolymers, poly(styrene‐co‐4‐methylstyrene) (SPSM), were prepared by styrene with 4‐methylstyrene using a Cp*Ti(OCH₃)₃/methyl aluminoxane (metallocene/MAO) catalyst. The effect of functionalization on the thermal properties and polymer structure of the SPSM membranes were also investigated. The crystallinity of the functionalized SPSM membrane is lower than that of the unfunctionalized SPSM membranes. The water molecules preferentially permeate through the SPSM membranes. Compared with unfunctionalized SPSM membranes, the functionalized SPSM membrane effectively increases the membrane formation performances and the pervaporation performances. The optimun pervaporation performance (a separation factor of 510 and permeation rate of 220 g/m²h) was obtained by the bromination of SPSM (SPSMBr) membrane with a 90 wt % aqueous ethanol solution. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 2247–2254, 2002     

Synthesis,properties and thermal stability of water‐soluble poly(potassium 1‐hydroxyacrylate‐co‐styrene) copolymer

The present work investigates the structure properties of copolymers using thermogravimetric analysis, hot stage microscopy, static light scattering, field emission scanning electron microscopy, X‐ray diffraction analysis and a Brookfield viscometer. Poly(potassium 1‐hydroxyacrylate) (PKHA) is a water‐soluble polymer. However, the copolymer of styrene and 2‐isopropyl‐5‐methylene‐1,3‐dioxolan‐4‐one is not water soluble at equal molar ratio because the polystyrene reduces the solubility. The effect of styrene on poly(potassium 1‐hydroxyacrylate‐co‐styrene) copolymer, i.e. poly(KHA‐co‐St), was investigated for the increasing solubility of the copolymer. The solubility was increased at a lower molar ratio of styrene such as 0.4 in the copolymer. It was found that the copolymer was soluble in water when a content ratio of 68/32 mol% of homopolymer was incorporated in poly(KHA₆₈‐co‐St₃₂) copolymer as determined by NMR analysis. Also the poly(KHA₆₈‐co‐St₃₂) copolymer was found to be salt tolerant, possessed water absorption capacity and was thermally stable up to 183 °C. Moreover, it is shown that the polystyrene content plays a key role in the thermal stability of the copolymer. © 2017 Society of Chemical Industry     

Synthesis and characterization of statistical copolymers of styrene and 4‐(1‐hydroxyalkyl)styrene

A family of new polymers based on poly(4‐(1‐hydroxyalkyl)styrene), and its copolymers with styrene were synthesized and thoroughly characterized by ¹H‐NMR, ¹³C‐NMR, FTIR, and UV spectroscopies. The chemical modification reactions of polystyrene (PS) was used as a novel method of performing the synthesis of poly(4‐(1‐hydroxyethyl‐co‐styrene)), poly(4‐(1‐hydroxypropyl‐co‐styrene)), poly(4‐(1‐hydroxybutyl‐co‐styrene)), and poly(4‐(1‐hydroxyphenylmethyl‐co‐styrene)). The novelty of this method lies in the incorporation of the desired mol % of the functional groups in polystyrene chain, to obtain random copolymers of desired composition. In preliminary testing/evaluation studies the utility and versatility of the new copolymers, which have the potential to be negative‐tone photoresist materials, were studied. Thus a few photoresist formulations based on poly(styrene‐co‐4‐(1‐hydroxyalkylstyrene)) were developed with 5 wt % of a photoacid generator. These studies suggested that the new copolymers synthesized by a simple and alternate method could have the same potential as a photoresist material when compared with the polymers synthesized by the polymerization of the corresponding functional monomer. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 1902–1914, 2004     

Exfoliated poly (styrene‐co‐methylstyrene) grafted‐polyaniline/layered double hydroxide nanocomposite synthesized by solvent blending method

Well defined poly (styrene‐co‐methylstyrene) grafted polyaniline/organo‐modified MgAl layered double hydroxide (LDH) was produced through solution intercalation method. After LDH nanoparticles were modified by the anion exchange reaction of MgAl (Cl) LDH with sodium dodecyl benzene sulfonate, Poly (styrene‐co‐methylstyrene) copolymers were synthesized by “living” free radical polymerization and then brominated with N‐bromosuccinimide. Afterwards, 1,4‐phenylenediamine was linked to brominated copolymers and prepared functionalized copolymer with amine. Poly (St‐co‐MSt)‐g‐PANI, has been synthesized by adding solution of ammonium persulfate and p‐toluenesufonic acid in DMSO solvent. Finally, Poly (styrene‐co‐methylstyrene) grafted‐Polyaniline/LDH nanocomposites were prepared by solution intercalation method. Characterization of these well‐defined nanocomposites included FT‐IR, gel permeation chromatography, thermogravimetric analysis, differential scanning calorimeter, transmission electron microscopy, and X‐ray diffraction. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011.     

Surface modification of linear low‐density polyethylene film by amphiphilic graft copolymers based on poly(higher α‐olefin)‐graft‐poly(ethylene glycol)

In this article, a series of amphiphilic graft copolymers, namely poly(higher α‐olefin‐co‐para‐methylstyrene)‐graft‐poly(ethylene glycol), and poly(higher α‐olefin‐co‐acrylic acid)‐graft‐poly(ethylene glycol) was used as modifying agent to increase the wettability of the surface of linear low‐density polyethylene (LLDPE) film. The wettability of the surface of LLDPE film could be increased effectively by spin coating of the amphiphilic graft copolymers onto the surface of LLDPE film. The higher the content of poly(ethylene glycol) (PEG) segments, the lower the water contact angle was. The water contact angle of modified LLDPE films was reduced as low as 25°. However, the adhesion between the amphiphilic graft copolymer and LLDPE film was poor. To solve this problem, the modified LLDPE films coated by the amphiphilic graft copolymers were annealed at 110° for 12 h. During the period of annealing, heating made polymer chain move and rearrange quickly. When the film was cooled down, the alkyl group of higher α‐olefin units and LLDPE began to entangle and crystallize. Driven by crystallization, the PEG segments rearranged and enriched in the interface between the amphiphilic graft copolymer and air. By this surface modification method, the amphiphilic graft copolymer was fixed on the surface of LLDPE film. And the water contact angle was further reduced as low as 14.8°. The experimental results of this article demonstrate the potential pathway to provide an effective and durable anti‐fog LLDPE film. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Atom transfer radical polymerization grafting of highly functionalized polystyrene and poly(4‐methylstyrene) macroinitiators with tert‐butyl acrylate

Two monodisperse graft copolymers, poly(4‐methylstyrene)‐graft‐poly(tert‐butyl acrylate) [number‐average molecular weight (M_n) = 37,500, weight‐average molecular weight/number‐average molecular weight (M_w/M_n) = 1.12] and polystyrene‐graft‐poly(tert‐butyl acrylate) (M_n = 72,800, M_w/M_n = 1.12), were prepared by the atom transfer radical polymerization of tert‐butyl acrylate catalyzed with Cu(I) halides. As macroinitiators, poly{(4‐methylstyrene)‐co‐[(4‐bromomethyl)styrene]} and poly{styrene‐co‐[4‐(1‐(2‐bromopropionyloxy)ethyl)styrene]}, carrying 40% of the bromoalkyl functionalities along the chain, were used. The dependencies of molecular parameters on monomer conversion fulfilled the criteria for controlled polymerizations. In contrast, the dependencies of monomer conversion versus time were nonideal; possible causes were examined. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 2930–2936, 2002     

Poly(styrene‐co‐N‐butylmaleimide) macroinitiators by controlled autopolymerization and related block copolymers

Autopolymerization of styrene‐N‐butylmaleimide mixtures at 125 or 140°C in the presence of a stable nitroxyl radical [2,2,6,6‐tetramethylpiperidin‐1‐yloxyl (TEMPO)] was found to proceed in a pseudoliving manner. Unimolecular initiators, which were originated by trapping self‐generated radical species with TEMPO, took part in the process. Under the studied experimental conditions, the TEMPO‐controlled autopolymerization with a varying comonomer ratio provided virtually alternating copolymers of narrow molecular weight distributions. The molecular weights of the copolymers increased with conversions. The obtained styrene‐N‐butylmaleimide copolymers containing TEMPO end groups were used to initiate the polymerization of styrene. The polymerization yielded poly(styrene‐co‐N‐butylmaleimide)‐polystyrene block copolymers with various polystyrene chain lengths and narrow molecular weight distributions. The compositions, molecular weights, and molecular weight distributions of the synthesized block copolymers and the initial poly(styrene‐co‐N‐butylmaleimide) precursors were evaluated using nitrogen analysis, gel permeation chromatography, and ¹H‐ and ¹³C‐NMR spectroscopy. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 2378–2385, 1999     

Synthesis and biodegradability evaluation of 2‐methylene‐1,3‐dioxepane and styrene copolymers

Biodegradable copolymers of 2‐methylene‐1,3‐dioxepane (MDO) and styrene (ST) were synthesized by free‐radical copolymerization using di‐t‐butyl peroxide (DTBP) as the initiator. The copolymers containing ester units were characterized by Fourier transform infrared (FTIR), ¹H‐NMR, and ¹³C‐NMR spectroscopy. Their molecular weight and polydispersity index were determined by gel permeation chromatography (GPC). In vitro enzymatic degradation of poly(MDO‐co‐ST) was performed at 37°C in phosphate buffer solution (PBS, pH = 7.4) in the presence of Pseudomonas lipase or crude enzyme extracted from earthworm. The experiment showed that incorporating ester units into C? C backbone chain of polystyrene would result in a biodegradable copolymer. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 1146–1151, 2007     

Cationic polymerization of α-methyl styrene from polydienes. II. Tensile properties of poly(butadiene-g-α-methyl styrene) and poly(styrene-b-butadiene-g-α-methyl styrene) copolymers

Tensile properties of poly(butadiene-g-α-methyl styrene) copolymers have been investigated on molded samples. These graft copolymers show thermoplastic elastomer behavior because of their graft copolymer structure. Both modulus and strength increase with increasing α-methyl styrene content and tensile strength is highest at the 45–50% by weight α-methyl styrene level. Tensile strength at elevated test temperatures is considerably higher for these poly(butadiene-g-α-methyl styrene) copolymers than for styrene-butadiene-styrene triblock polymers. This is attributed to the higher glass transition temperature for poly(α-methyl styrene) segments compared to polystyrene segments. The oil acceptance of these graft copolymers appears to depend on the number of loose polybutadiene chain ends. Thus, the tensile strength of oil-extended poly(butadiene-g-α-methyl styrene) copolymers was considerably lower than oil-extended poly(styrene-b-butadiene-g-α-methyl styrene) copolymers even though both copolymers contained equal hard segment contents.     

Synthesis and characterization of poly (styrene‐b‐[(butadiene)1−x‐(ethylene‐co‐butylene)x] ‐b‐styrene) star‐like molecular polymers produced by partial hydrogenation of SBS

This article reports the synthesis and characterization of four arm star‐shaped poly(styrene‐b‐[(butadiene)_1?x‐(ethylene‐co‐butylene)_x]‐b‐styrene) (SBEBS) copolymers. A series of SBEBS copolymers with different compositions of the elastomeric block were produced by hydrogenating a given poly(styrene‐b‐butadiene‐b‐styrene) (SBS) copolymer using a catalyst prepared from bis(η⁵‐cyclopentadienyl)titanium(IV) dichloride and n‐butyllithium. The characterization was accomplished by proton nuclear magnetic resonance spectroscopy (¹H NMR), infrared spectroscopy (FTIR), gel permeation chromatography (GPC), differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA), and thermogravimetric analysis (TGA). The results indicate that there is a selective saturation of the polybutadiene block over the polystyrene block; this selectivity was determined by the Ti/Li molar ratio and the concentration of Ti. It was observed that the saturation rate of the 1,2‐vinyl was higher than that of the 1,4‐trans and 1,4‐cis poly(butadiene)‐b isomers. The DSC and DMA results indicate that the degree of hydrogenation had a profound effect on the polymer's relaxation behavior. All samples exhibited a biphasic system behavior with two distinct transitions corresponding to the elastomeric and polystyrene blocks. SBEBS copolymers with higher saturation levels (>33%) exhibited a crystalline character. The TGA results indicated a characteristic weight loss temperature in all samples, with slightly higher thermal degradation stabilities in the materials with higher degrees of saturation. POLYM. ENG. SCI., 54:2332–2344, 2014. © 2013 Society of Plastics Engineers     

Preparation and application of sulfonated poly(1‐octene‐co‐styrene)

In this article, 1‐octene and styrene was copolymerized by the supported catalyst (TiCl₄/ID/MgCl₂). Subsequently, by sulfonation reaction, sulfonated poly(1‐octene‐co‐styrene)s which were amphiphilic copolymers were prepared. The copolymerization behavior between 1‐octene and styrene is moderate ideal behavior. Copolymers prepared by this catalyst contain appreciable amounts of both 1‐octene and styrene. Increase in the feed ratio of styrene/1‐octene leads to increase in styrene content in copolymer and decrease in molecular weight. As the polymerization temperature increases, the styrene content in the copolymers increases, however, the molecular weight decreases. Hydrogen is an efficient regulator to lower the molecular weights of poly(1‐octene‐co‐styrene)s. The sulfonation degree of the sulfonated poly(1‐octene‐co‐styrene)s increased as the styrene content in copolymer increased or the molecular weight decreased. Thirty‐six hour is long enough for sulfonation reaction. The sulfonated poly(1‐octene‐co‐styrene)s can be used as effective and durable modifying agent to improve the wettability of polyethylene film and have potential application in emulsified fuels and for the stabilization of dispersions. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Preparation and applicability of functionalized polyethylene with an ethylene/1,7‐octadiene copolymer

The copolymerization of ethylene and 1,7‐octadiene was carried out to synthesize polyethylene with unreacted vinyl groups. The prepared copolymer [poly (ethylene‐co‐1,7‐octadiene) (PEOD)] was epoxidized with peracetic acid, m‐chloroperbenzoic acid, or formic acid/H₂O₂. Of these, peracetic acid gave the best results. Epoxidized PEOD was subjected to a reaction with 2‐mercaptobenzimidazole and poly(L ‐lactic acid). The bromination of PEOD was also performed in the presence of a Br₂/HBr solution at room temperature. The brominated poly(ethylene‐co‐1,7‐octadiene) (PEOD‐Br) was used as a macroinitiator for atom transfer radical polymerization. The polymerization of styrene, butyl methacrylate, and glycidyl methacrylate was performed in bulk or solution at 120°C with a PEOD‐Br/CuBr/2,2′‐dipyridyl initiator system. The thermal properties of the graft copolymers and the efficiency of the graft polymerization were investigated. These graft copolymers have potential applications as interfacial modifiers. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Graft copolymerization of methylmethacrylate with N‐substituted maleimide‐styrene copolymer by ATRP

Atom transfer radical polymerization (ATRP) was employed to prepare graft copolymers having poly(MBr)‐alt‐poly(St) copolymer as backbone and poly(methyl methacrylate) (PMMA) as branches to obtain heat resistant graft copolymers. The macroinitiator was prepared by copolymerization of bromine functionalized maleimide (MBr) with styrene (St). The polymerization of MMA was initiated by poly(MBr)‐alt‐poly(St) carrying bromine groups as macroinitiator in the presence of copper bromide (CuBr) and bipyridine (bpy) at 110°C. Both macroinitiator and graft copolymers were characterized by ¹H NMR, GPC, DSC, and TGA. The ATRP graft copolymerization was supported by an increase in the molecular weight (MW) of the graft copolymers as compared to that of the macroinitiator and also by their monomodal MW distribution. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci, 2006     

Characterization and thermal properties of poly(n‐butyl acrylate‐g‐styrene) graft copolymers

Poly(butyl acrylate‐g‐styrene) graft copolymers were prepared by free‐radical polymerization using a polystyrene macromonomer carrying a methacryloyloxy group at the chain end and they were characterized by size‐exclusion chromatography, and Fourier transform infrared spectroscopy. Glass transition temperatures and degradation behavior were determined by thermal analysis. Only a single glass transition temperature was observed for the resulting graft copolymers, indicating the miscibility between the poly(styrene) phase and poly(butyl acrylate) (pBA) phase in the graft copolymer. The incorporation of polystyrene segments in the graft copolymer improved the thermal stability of pBA and enhanced the apparent activation energy for the thermal degradation of pBA. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 783–789, 2001     

Study on a new kind of polypropylene‐graft‐ polystyrene: Preparation and application

A novel synthetic route for preparing polypropylene‐graft‐polystyrene (PP‐g‐PSt) was set up. With this synthetic route, a series of PP‐g‐PSt copolymers containing different percentages of polystyrene chain were synthesized, based on the different reactivities of two kinds of C? C double bonds on 4‐(3‐butenyl) styrene. Characterization data, including ¹H‐NMR, ¹³C‐NMR, GPC, and DSC, demonstrated that the graft copolymers were all very pure. Furthermore, it was also attempted to use this new kind of propylene–styrene graft copolymer as a compatibilizer. DMA and SEM results illustrated that the PP‐g‐PSt obtained is an efficient compatibilizer for the polypropylene–polystyrene blend. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 314–322, 2004     

Characterization and application of polypropylene films modified with stimuli‐sensitive copolymers with an Ar‐plasma postpolymerization technique

Surface‐modified polypropylene (PP) films with thermally and photochemically sensitive copolymers consisting of N‐(2‐hydroxypropyl)methacrylamide (HPMA) and 4‐(4‐methoxyphenylazo)phenyl methacrylate (MPAP), poly(HPMA‐co‐MPAP)‐g‐PP (abbreviated g‐PP) film, were prepared by graft copolymerization with an Ar‐plasma postpolymerization technique. The surfaces of the g‐PP films were characterized by means of X‐ray photoelectron spectroscopy; the percentage grafting of poly(HPMA‐co‐MPAP) with a number‐average molecular weight of 3.28 × 10⁴ was 7.12%, and the molar ratio of HPMA–MPAH in the copolymer was 0.75:0.25. The stimuli‐sensitive adsorption of albumin and polystyrene microspheres on the g‐PP film was also measured. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 143–148, 2003     

Preparation of Tethered Half-Titanocene Complex on Syndiotactic Poly(styrene-<Emphasis Type="Italic">co</Emphasis>-<Emphasis Type="Italic">p</Emphasis>-methylstyrene) for Using in Syndiospecific Polymerization of Styrene

Abstract  

In this work the syndiotactic polystyrene copolymer, poly (styrene-co-p-methylstyrene) was prepared by the copolymerization of styrene and p-methylstyrene with cyclopentadienyltitanium trichloride/methylaluminoxane catalyst. This copolymer was functionalized with silyl-hydride groups. The structure of copolymer and functionalized copolymer were characterized by FT-IR, ¹H-NMR and ¹³C-NMR spectroscopy. The obtained results revealed that the functionalization reaction successfully proceeds at low temperatures. Tethering of half-titanocene complex on polymeric support was done by the hydrosilylation reaction of 1-allylindenyltrichlorotitanium with silyl-hydride functionalized copolymer in the presence of Karstedt catalyst as a coupling reagent. The polymer-supported catalyst was tested for syndiospecific polymerization of styrene using methylaluminoxane as a cocatalyst. The results of styrene polymerization showed that the polymer-supported catalyst exhibited high activity for syndiospecific polymerization of styrene. The polymer prepared with supported catalyst was characterized by carbon nuclear magnetic resonance (¹³C-NMR) and differential scanning calorimetry (DSC). The results confirmed the syndiotacticity of obtained polymers. X-ray diffraction (XRD) analysis showed the δ-form crystalline structure of obtained syndiotactic polystyrene.     

Facile synthesis of poly(4‐hydroxy styrene) from polystyrene

A facile methodology to modify polystyrene, to incorporate alkali soluble hydroxy groups, is reported. Polystyrene of well‐defined number‐average molecular weights in the range of 3000 to 50,000 were prepared by suspension polymerization at 80°C by varying the relative mole ratio of carbon tetrachloride, used as chain transfer agent. Polystyrenes were acetylated; the acetyl groups were converted to acetoxy groups, by Baeyer–Villiger oxidation, and hydrolyzed in a nonaqueous alkaline medium to generate hydroxy groups. The extents of modifications were monitored by infrared spectroscopy. The glass transition temperatures of poly(4‐acetylstyrene‐co‐styrene), poly(4‐acetylstyrene‐co‐4‐acetoxystyrene‐co‐styrene), and poly(4‐hydroxystyrene‐co‐4‐acetylstyrene‐co‐styrene) were 107, 134, and 142°C, respectively. The polymers were evaluated in photoresist formulations. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 91: 3192–3201, 2004     

Synthesis of well‐defined polystyrene‐graft‐poly(methyl methacrylate)

A well‐defined graft copolymer, polystyrene‐graft‐poly(methyl methacrylate), was synthesized in two steps. In the first step, styrene and p‐vinyl benzene sulfonyl chloride were copolymerized via reversible addition–fragmentation chain transfer polymerization (RAFT) in benzene at 60 °C with 2‐(ethoxycarbonyl)prop‐2‐yl dithiobenzoate as a chain transfer agent and 2,2′‐azobis(isobutyronitrile) as an initiator. In the second step, poly[styrene‐co‐p‐(vinyl benzene sulfonyl chloride)] was used as a macroinitiator for the atom transfer radical polymerization (ATRP) of methyl methacrylate (MMA) in toluene at 80 °C with CuCl as a catalyst and 2,2′‐bipyridine as a ligand. With sulfonyl chloride groups as the initiating sites for the ATRP of MMA, high initiation efficiencies were obtained. Copyright © 2006 Society of Chemical Industry