Study on superabsorbent composites. XVIII. Preparation,characterization, and property evaluation of poly(acrylic acid‐co‐acrylamide)/organomontmorillonite/sodium humate superabsorbent composites

A series of novel multifunctional poly (acrylic acid‐co‐acrylamide) (PAA‐AM)/organomontmorillonite (O‐MMT)/sodium humate (SH) superabsorbent composites were synthesized by the graft copolymerization reaction of partially neutralized acrylic acid and acrylamide on O‐MMT micropowder and SH with N,N′‐methylene bisacrylamide as a crosslinker and ammonium persulfate as an initiator in an aqueous solution. The superabsorbent composites were characterized by means of Fourier transform infrared spectroscopy, X‐ray diffraction, scanning electron microscopy, and thermogravimetric analysis. The effect of the relative weight ratio of SH to O‐MMT on the water absorbency was studied, and the results indicated that the best water absorbency of 591 g/g in distilled water was obtained when an O‐MMT content of 20 wt % and an SH content of 30 wt % were incorporated. The superabsorbent composite possessed a good capacity for water retention; even after 30 days, 24.4 wt % of water could still be saved by the sand soil containing 1.0 wt % superabsorbent composite. The results from this study show that the water absorbency of a superabsorbent composite is improved by the simultaneous introduction of O‐MMT and SH into a PAA‐AM network in comparison with the incorporation of only O‐MMT or SH. Also, in comparison with PAA‐AM/MMT/SH, an appropriate amount of O‐MMT can benefit the developed composites with respect to their water absorbency, salt resistance, and capacity for water retention in sand soil. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Preparation and slow‐release property of a poly(acrylic acid)/attapulgite/sodium humate superabsorbent composite

A novel poly(acrylic acid)/attapulgite (APT)/sodium humate (SH) superabsorbent composite was synthesized through the graft copolymerization reaction of acrylic acid on APT micropowder and SH with N,N′‐methylene bisacrylamide as a crosslinker and ammonium persulfate as an initiator in an aqueous solution. Various effects on the water absorbency, including the amounts of the crosslinker, initiator, APT, and SH, were investigated. The superabsorbent composite was characterized with Fourier transform infrared spectroscopy and scanning electron microscopy. The superabsorbent composite synthesized under optimal synthesis conditions with an APT concentration of 20% and an SH concentration of 20% exhibited absorption of 583 g of H₂O/g of sample and 63 g of H₂O/g of sample in distilled water and in a 0.9 wt % NaCl solution, respectively. The slow‐release property of SH from the superabsorbent composite into water was measured, and a test of the water retention of the superabsorbent composite in soil was also carried out experimentally with and without the superabsorbent composite. The results showed that the superabsorbent composite had not only good water retention but also an additional slow‐release property of SH. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 37–45, 2007     

Study on superabsorbent composite. VIII. Effects of acid‐ and heat‐activated attapulgite on water absorbency of polyacrylamide/attapulgite

A novel superabsorbent composite, polyacrylamide/attapulgite, from acrylamide (AM) and attapulgite (APT), was prepared by free‐radical polymerization, using N,N′‐methylenebisacrylamide (MBA) as a crosslinker and ammonium persulfate (APS) as an initiator. The effects of hydrochloric acid (HCl) concentration, acidification time, and acidification temperature while acidifying APT and temperature and APT heat‐activation on water absorbency of the superabsorbent composite in distilled water and in 0.9 wt % NaCl solution were studied. The water absorbency first decreases with increasing the HCl concentration while acidifying APT, and then increases with further increasing the HCl concentration. Prolongation of acidification time is of benefit to the increase of water absorbency. At a given HCl concentration, water absorbency for the composite increases with increasing acidification temperature. An important increase in water absorbency was observed after incorporating heat‐activated APT into the polymeric network, reaching a maximum of 1964 g g^?1 with the APT heat‐activated at 400°C. Acid‐ and heat‐activation can influence chemical composition, crystalline structure, cation exchange capacity (CEC), and specific surface area of APT according XRF, XRD, FTIR analysis, and physicochemical properties test, and then on water absorbency of corresponding PAM/APT superabsorbent composite. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 2419–2424, 2007     

GG-g-PAA／SH高吸水性树脂的制备与缓释性能研究

以天然瓜尔胶（GG）、丙烯酸（AA）和腐植酸钠（SH）为原料,过硫酸铵为引发剂,N,N’-亚甲基双丙烯酰胺为交联剂,采用水溶液聚合法制备了环境友好的多功能瓜尔胶接枝聚丙烯酸／腐植酸钠（GG-g—PAA／SH）高吸水性树脂。考察了腐植酸钠含量对树脂吸水性能的影响,评价了树脂在沙土中的实际保水性能、反复溶胀性能和腐植酸钠肥料缓释性能。结果表明,在体系中引入廉价的腐植酸钠,不但降低生产成本,还能提高树脂的吸水能力,当腐植酸钠含量为15wt％时,高吸水性树脂吸蒸馏水和生理盐水的倍率分别为532g／g和62g／g。在沙土中加入高吸水性树脂能显著提高其保水性能,30d后仍能保持13％的水分。此外,GG-g-PAA／SH高吸水性树脂还具有较优的反复溶胀性能和腐植酸钠肥料缓释功能,可用作兼具吸水、保水和缓释性能的新型节水材料。     

Utilization of plant ash for the fabrication of novel superabsorbent composites with potassium‐release characteristics

Design and synthesis of the agricultural and ecological superabsorbent materials with cost‐efficient and fertilizer‐release characteristics has recently attracted considerable interests. In this work, the novel poly(sodium‐potassium acrylate‐co‐acrylamide)/plant ash (PNa‐KA‐co‐AM/PA) superabsorbent composites with potassium‐release characteristics were prepared using partially neutralized acrylic acid (Na‐KA), acrylamide (AM), and plant ash (PA) as raw materials, ammonium persulfate (APS) as the initiator, and N,N′‐methylenebisacrylamide (MBA) as the crosslinker. The structure, morphologies, and thermal stability of the composites were characterized by Fourier transform infrared spectrophotometer, scanning electron microscopy, and TGA techniques, respectively. The effects of MBA concentration and PA content on water absorbency were studied, and the swelling properties of the composites in saline solutions and various pHs solution as well as their potassium‐release capabilities were also evaluated. Results indicate that the composites exhibit better thermal stability, salt‐resistant performance, pH‐stability, and potassium‐release properties, and can act as a fertilizer and an effective water‐saving material for agricultural and ecological application. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Preparation of starch‐graft‐poly(acrylamide)/attapulgite superabsorbent composite

A novel starch‐graft‐poly(acrylamide)/attapulgite superabsorbent composite was synthesized by graft copolymerization reaction of starch, acrylamide (AM), and attapulgite micropowder using N.N‐methylene‐bisacrylamide (MBA) as a crosslinker and ammonium persulphate (APS) as an initiator in aqueous solution, followed by hydrolysis with sodium hydroxide. The effects on water absorbency, such as amount of crosslinker, initiator, attapulgite, weight ratio of acrylamide to starch in the feed, gelatinization conditions of starch and molar ratio of NaOH to acrylamide, and so forth, were investigated. These superabsorbent composites were characterized by Fourier transform infrared spectroscopy (FTIR) and thermogravimetric analysis (TGA). The water absorbencies for these superabsorbent composites in water and saline solution were investigated, and water retention tests were carried out. Results obtained from this study showed that the water absorbency of superabsorbent composite synthesized under optimal synthesis conditions with an attapulgite content of 10% exhibit absorption of 1317 g H₂O/g sample and 68 g H₂O/g sample in distilled water and in 0.9 wt % NaCl solution, respectively. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 1351–1357, 2005     

Synthesis,characterization and swelling behaviors of hydroxyethyl cellulose‐g‐poly(acrylic acid)/attapulgite superabsorbent composite

In this work, a series of novel hydroxyethyl cellulose‐ g‐poly(acrylic acid)/attapulgite (HEC‐g‐PAA/APT) superabsorbent composites were prepared through the graft polymerization of hydroxyethyl cellulose (HEC), partially neutralized acrylic acid (AA), and attapulgite (APT) in aqueous solution, and the composites were characterized by means of Fourier‐transform spectroscopy, scanning electron microscopy, and transmission electronmicroscopy. The effects of polymerization variables including concentrations of the initiator and crosslinker and APT content on water absorbency were studied, and the swelling properties in various pH solutions as well as the swelling kinetics in various saline solutions were also systematically evaluated. Results showed that the introduction of 5 wt% APT into HEC‐g‐PAA polymeric network could improve both water absorbency and water absorption rate of the superabsorbent composites. In addition, the superabsorbent composites retained high water absorbency over a wide pH range of 4–10, and the swelling kinetics of the superabsorbent composites in CaCl₂ and FeCl₃ solutions exhibited a remarkable overshooting phenomenon. POLYM. ENG. SCI., 2010. © 2010 Society of Plastics Engineers     

Granular urea‐formaldehyde slow‐release fertilizer with superabsorbent and moisture preservation

To improve the utilization of fertilizer and water resource at the same time, a new type of slow‐release fertilizer with superabsorbent and moisture preservation was developed, with the combination of slow‐release technique and superabsorbent polymers. The coatings were formed by the inverse phase polymerization technique. The element analysis results showed that the product contained 22.58% nitrogen element, and the water absorbency of the product was 94 times its own weight if it was allowed to swell in tap water at room temperature for 2 h. The results of the slow‐release behavior of N and the water absorbency and retention properties in soil showed that the product not only had good slow‐release property but also had excellent water absorbency and water retention capacity, which was a significant advantage over the normal slow‐release or controlled‐release fertilizers. The effects of the amount of initiator, crosslinker, reaction time, and the degree of neutralization of acrylic acid on water absorbency were investigated and optimized. At the same, a rather new and simple method was used to make homogeneous urea‐formaldehyde granules. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 99: 3230–3235, 2006     

Preparation and properties of a salt‐resistant superabsorbent polymer

Crosslinked sodium polyacrylate was prepared by solution polymerization with N,N‐methylene‐bisacrylamide (bisAM) as crosslinking agent; it was subsequently surface‐crosslinked by ethylene glycol diglycidyl ether (EGDE) and then was modified with inorganic salt to obtain a superabsorbent with water absorbency in 0.9 wt % NaCl aqueous solution at atmosphere and applied pressure (P ≈ 2 × 10³ Pa) of 55 and 20 g.g^?1, respectively. Moreover, it also had excellent hydrogel strength. The effects of reaction temperature, reaction time, neutralization degree (ND) of acrylic acid, amount of initiator, crosslinking agent, and surface‐crosslinking agent, mass ratio of inorganic salt to initial superabsorbent, molar ratio of sodium aluminate (NaAlO₂) to potassium dihydrogen hyphosphate (KH₂PO₄) on water absorbency (WA) in 0.9 wt % NaCl aqueous, and the hydrogel modulus were investigated and optimized. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 2532–2541, 2004     

Utilization of waste polystyrene and starch for superabsorbent composite preparation

A superabsorbent composed of waste polystyrene, starch, and acrylic acid was prepared through emulsion polymerization. The effects of major factors such as starch, acrylic acid, initiator, crosslinker, and bentonite contents and the neutralization degree of acrylic acid on water absorbency were investigated to obtain optimum conditions with high swelling capacity. The superabsorbent hydrogel was characterized by scanning electron microscope (SEM), Fourier transform infrared (FTIR) spectroscopy, and thermogravimetric analysis (TGA). The FTIR results confirmed that the grafting polymerization took place among the polystyrene, acrylic acid, starch, and bentonite. The introduction of bentonite particles into the polystyrene‐g‐poly (acrylic acid)‐co‐starch system could increase the water absorbency. The superabsorbent composite containing 3 wt % bentonite had the highest water absorbency (500 g/g in distilled water and 49 g/g in 0.9 wt % NaCl solution). © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Study on superabsorbent composite. XX. Effects of cation‐exchanged montmorillonite on swelling properties of superabsorbent composite containing sodium humate

In this work, the effects of different cation‐exchanged montmorillonite on water absorbency of poly(acrylic acid‐co‐acrylamide)/montmorillonite/sodium humate (PAA‐AM/MMT/SH) superabsorbent composite were systematically investigated under the same preparation conditions. The superabsorbents doped with different cation‐exchanged montmorillonite were characterized by Fourier‐transform infrared spectroscopy, X‐ray diffraction, and scanning electron microscopy technologies. Swelling behaviors of developing superabsorbent composite in various cationic saline solutions (NaCl, CaCl₂, and FeCl₃) were also investigated. The water absorbencies of superabsorbent composite with 20 wt% MMT and 30 wt% SH are 638, 723, 682, and 363 g g⁻¹ in distilled water for incorporating natural Na⁺‐MMT, Li⁺‐exchanged MMT, Ca²⁺‐exchanged MMT, and Al³⁺‐exchanged MMT, respectively. The results showed that the cation‐exchange process had some obvious influences on final water absorbency of superabsorbent composite. NaCl, CaCl₂, and FeCl₃ solutions did not alter the swelling characteristics of the superabsorbent materials at a concentration of less than 0.01 mM, however, a concentration of greater than 0.1 mM caused a collapse in the swelling curves. The excellent swelling‐reswelling‐swelling behavior and lower swelling rate testified that Al³⁺‐exchanged MMT can act as an assistant crosslinker in the polymeric network. POLYM. COMPOS., 2009. © 2008 Society of Plastics Engineers     

Enhanced swelling and methylene blue adsorption of polyacrylamide‐based superabsorbents using alginate modified montmorillonite

Polyacrylamide/sodium alginate modified montmorillonite (PAM/SA‐MMT) superabsorbent composites were synthesized by free‐radical polymerization under normal atmospheric conditions. They were characterized by X‐ray diffraction, scanning electron microscopy, and Fourier transform infrared spectroscopy (FTIR). Their water absorbency and methylene blue (MB) adsorption behaviors were studied. Compared with PAM/MMT composites, PAM/SA‐MMT composites demonstrated greater water absorbency (863 g g^?1 in distilled water and 101 g g^?1 in 0.9 wt % NaCl solution) and higher adsorption capacity of 2639 mg g^?1 for MB. The adsorption behaviors of the composites showed that the isotherms and adsorption kinetics were in good agreement with the Langmuir equation and pseudo‐second‐order equation, respectively. FTIR analysis suggested that the MB adsorption of PAM/SA‐MMT composites via a mechanism combined electrostatic, H‐bonding and hydrophobic interaction. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2014 , 131, 40013.     

Synthesis of poly(acrylic acid)/sodium humate superabsorbent composite for agricultural use

A novel poly (acrylic acid)/sodium humate superabsorbent composite was synthesized by graft copolymerization reaction of acrylic acid (AA) on sodium humate micropowder using N,N′‐methylenebisacrylamide (MBA) as a crosslinker and potassium peroxydisulfate (KPS) as an initiator in aqueous solution. The effects on water absorbency of factors such as reaction temperature, initial monomer concentration, and degree of neutralization of AA, amount of crosslinker, initiator, and sodium humate were investigated. The superabsorbent composite was characterized by scanning electron microscopy, and the graft copolymerization reaction of AA on sodium humate micropowder was characterized by IR spectroscopy. Results obtained from this study show that the water absorbency of the superabsorbent composite synthesized under optimal conditions for synthesis with a sodium humate content of 5.3% exhibited absorption of 684 g H₂O/g sample in distilled water. Water‐retention in soil is enhanced by the use of the superabsorbent composite. The effect of superabsorbent composite on the growth of corn is reported. The superabsorbent composite may be of use as water management materials for agriculture purposes in desert and drought‐prone areas. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 5137–5143, 2006     

Synthesis and properties of carboxymethyl cellulose‐graft‐poly(acrylic acid‐co‐acrylamide) as a novel cellulose‐based superabsorbent

A new cellulose‐based superabsorbent polymer, carboxymethyl cellulose‐graft‐poly(acrylic acid‐co‐acrylamide), was prepared by the free‐radical grafting solution polymerization of acrylic acid (AA) and acrylamide (AM) monomers onto carboxymethyl cellulose (CMC) in the presence of N,N′‐methylenebisacrylamide as a crosslinker with a redox couple of potassium persulfate and sodium metabisulfite as an initiator. The influences of reaction variables such as the initiator content, crosslinker content, bath temperature, molar ratio of AA to AM, and weight ratio of the monomers to CMC on the water absorbency of the carboxymethylcellulose‐graft‐poly(acrylic acid‐co‐acrylamide) copolymer were investigated. The copolymer's structures were characterized with Fourier transform infrared spectroscopy. The optimum reaction conditions were obtained as follows: the bath temperature was 50°C; the molar ratio of AA to AM was 3 : 1; the mass ratio of the monomers to CMC was 4 : 1; and the weight percentages of the crosslinker and initiator with respect to the monomers were 0.75 and 1%, respectively. The maximum water absorbency of the optimized product was 920 g/g for distilled water and 85 g/g for a 0.9 wt % aqueous NaCl solution. In addition, the superabsorbent possessed good water retention and salt resistance. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 1382–1388, 2007     

Preparation and Swelling Behavior of Fast‐Swelling Superabsorbent Hydrogels Based On Starch‐g‐Poly(acrylic acid‐co‐sodium acrylate)

Summary: A novel fast‐swelling porous superabsorbent hydrogel was prepared by grafting acrylic acid onto corn starch through free‐radical polymerization in aqueous solution using N,N′‐methylenebisacrylamide as a crosslinker, ammonium persulfate as an initiator, sodium dodecyl sulfate and p‐octyl poly(ethylene glycol)phenyl ether as pore‐forming agents. The graft polymerization and surface morphology of the porous superabsorbents were characterized by FTIR and SEM. The results indicate that the porous superabsorbents were endowed with higher equilibrium water absorbency and faster swelling rate (they needed only 10 min to reach 90% of their equilibrium water absorbency) compared with the nonporous superabsorbents. The dewatering method employed had a significant influence on the swelling behavior of the superabsorbents and dewatering agents were useful to preserve the pores formed during the polymerization process.

The equilibrium water absorbency in distilled water, for the porous and non‐porous starch‐g‐poly(acrylic acid‐co‐sodium acrylate) superabsorbent hydrogels dried through different procedures.     

Preparation and characterization of water‐soluble polyacrylate sodium modified by organomontmorillonite

Water‐soluble high intrinsic viscosity organomontmorillonite modified polyacrylate sodium (OMMT‐modified PNaA) was prepared via an in situ intercalation adiabatic polymerization of sodium acrylate in the presence of OMMT. The FTIR and XRD analyses correspond to the OMMT‐modified PNaA with exfoliated structure of OMMT. The influences of prepared conditions on intrinsic viscosity and dissolving time of the modified polymers had been investigated in this study. It was found that the incorporation of as little as 0.1 wt % of OMMT added to PNaA matrix could be effective to enhance intrinsic viscosity of the modified PNaA. TGA and DSC studies confirmed the enhancement of the thermal stability of the OMMT‐modified PNaA when compared with PNaA. Furthermore, the solution behavior studies of the modified PNaA showed the “antipolyelectrolyte” effect and high “antishearing” property. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Superabsorbent composite XXII: Effects of modified sepiolite on water absorbency and swelling behavior of chitosan‐g‐poly(acrylic acid)/sepiolite superabsorbent composite

In this work, a series of chitosan‐g‐poly(acrylic acid)/sepiolite (CTS‐g‐PAA/ST) superabsorbent composites containing raw sepiolite, acid‐activated sepiolite, and cation‐exchanged sepiolite were synthesized by free‐radical graft polymerization in aqueous solution, using N,N′‐methylenebisacrylamide as a crosslinker and ammonium persulfate as an initiator. The effects of raw sepiolite, acid‐activated sepiolite, and cation‐exchanged sepoilite on equilibrium water absorbency, swelling rate, and swelling behavior in different pH value solution of superabsorbent composites were systematically investigated. The results from FTIR spectra showed that chitosan and sepiolite participated in graft polymerization reaction with acrylic acid. The introduction of acid‐activated and cation‐exchanged sepiolite into chitosan‐g‐poly(acrylic acid) polymeric network could improve water absorbency and swelling rate compared with that of the raw sepiolite. All prepared samples have similar swelling behavior in different pH solutions and the equilibrium water absorbencies of samples keep roughly constant in the pH range from 4 to 12. POLYM. COMPOS., 2010. © 2009 Society of Plastics Engineers     

Preparation of polyacrylamide/graphite oxide superabsorbent nanocomposites with salt tolerance and slow release properties

Novel polyacrylamide/graphite oxide (PAM/GO) superabsorbent nanocomposites were synthesized by a simple solution polymerization of acrylamide using N,N ′‐methylenebisacrylamide as crosslinker and ammonium persulfate as initiator. The well dispersion of GO nanoplatelets in the polymeric network results in a remarkable improvement on the comprehensive swelling performance of the resulting superabsorbent nanocomposites. The water absorption experimental results show that the superabsorbent nanocomposites could absorb water as twice as that of crosslinked polyacrylamide (PAM) superabsorbent with a weight gain of 400 g g^?1 with a low loading of GO. The salt tolerance and water‐retention ability of the resulting PAM/GO superabsorbent nanocomposites are also enhanced compared with PAM. Moreover, by embedding of ammonium salt into PAM/GO network, the PAM/GO superabsorbent nanocomposites also exhibit a slow release behavior of ammonium salt from network when swelling in water, which makes the PAM/GO superabsorbent nanocomposites multifunctional absorbent materials with great potential for agricultural and horticultural applications. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Synthesis and characterization of a salt‐resisting superabsorbent based on poly(acrylic acid) with sodium tungstate as a crosslinker

A novel salt‐resistant superabsorbent polymer was synthesized by solution polymerization from the monomer acrylic acid (AA) with potassium persulfate as the initiator. Sodium tungstate was first employed as a crosslinker in the preparation to achieve a better crosslinked polymer (WPAA). In addition to the xerogel WPAA, sodium hydroxide and tris(2‐hydroxyethyl)amine (TEA) were introduced for the preparation of WPAA–sodium and WPAA–TEA hydrogels, respectively. The effect on the water absorbency of factors such as the reaction temperature, degree of neutralization of AA, and amounts of the crosslinker sodium tungstate and the initiator were investigated. The crosslinked xerogels were characterized with infrared spectroscopy. These crosslinked superabsorbent composites with sodium tungstate were characterized with thermogravimetric analysis and scanning electron microscopy. The water absorbencies of these superabsorbent composites in water and saline solutions were investigated. Results obtained from this study showed that under the same synthesis conditions, in comparison with superabsorbent composites with an aluminum salt as a crosslinker and styrene as a graft copolymer, the salt resistance of the superabsorbent composite synthesized with sodium tungstate as a crosslinker was obviously enhanced. Moreover, the WPAA–TEA xerogel had absorbency values of 223.6 and 81.9 g/g for distilled water and a 0.9 wt % NaCl solution, respectively, and it showed better salt resistance and a better water‐absorbing rate than the WPAA–sodium xerogel because of the modification with triethanolamine. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Synthesis of AA‐based superabsorbent interpenetrated with sodium PVA sulfate

An interpenetrating network of acrylic acid (AA)‐based superabsorbents and sodium PVA sulfate (SPS) were prepared by copolymerizing AA and N,N′‐methylene bisacrylamide as a crosslinking monomer in a solution of SPS with KPS, a radical initiator. The SPS was prepared through the sulfation of the hydroxyl groups of PVA with DMF‐SO₃ complex in DMSO. The AA‐based superabsorbent interpenetrated with SPS (SA‐IP‐SPS) showed superior properties such as higher water and saline absorbency, absorbency under load (AUL), and water retention value (WRV) compared with AA‐based superabsorbent due to the interpenetrated SPS. The maximum water and saline absorbency of SA‐IP‐SPS was 1753 and 125.6 g/g, respectively. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 78: 2525–2532, 2000