Thermal properties of melt‐blended poly(ether ether ketone) and poly(ether imide)

The thermal properties of blends of poly(ether ether ketone) (PEEK) and poly(ether imide) (PEI) prepared by screw extrusion were investigated by differential scanning calorimetry. From the thermal analysis of amorphous PEEK–PEI blends which were obtained by quenching in liquid nitrogen, a single glass transition temperature (T_g) and negative excess heat capacities of mixing were observed with the blend composition. These results indicate that there is a favorable interaction between the PEEK and PEI in the blends and that there is miscibility between the two components. From the Lu and Weiss equation and a modified equation from this work, the polymer–polymer interaction parameter (χ₁₂) of the amorphous PEEK–PEI blends was calculated and found to range from −0.058 to −0.196 for the extruded blends with the compositions. The χ₁₂ values calculated from this work appear to be lower than the χ₁₂ values calculated from the Lu and Weiss equation. The χ₁₂ values calculated from the T_g method both ways decreased with increase of the PEI weight fraction. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 72: 733–739, 1999     

Crystallization and melting behavior of poly(p‐phenylene sulfide) in blends with poly(ether sulfone)

Crystallization and melting behaviors of poly(p‐phenylene sulfide) (PPS) in blends with poly(ether sulfone) (PES) prepared by melt‐mixing were investigated by differential scanning calorimetry (DSC). The blends showed two glass transition temperatures corresponding to PPS‐ and PES‐rich phases, which increased with increasing PES content, indicating that PPS and PES have some compatibility. The cold crystallization temperature of the blended PPS was a little higher than that of pure PPS. Also, the heats of crystallization and melting of the blended PPS decreased with increasing PES content, indicating that the degree of crystallinity decreased with an increase of PES content. The isothermal crystallization studies revealed that the crystallization of PPS is accelerated by blending PPS with 10 wt % PES and further addition results in the retardation. The Avrami exponent n was about 4 independent on blend composition. The activation energy of crystallization increased by blending with PES. The equilibrium melting point decreased linearly with increasing PES content. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 1686–1692, 1999     

Miscibility and crystallization behavior of the solution‐blended sulfonated poly(phenylene oxide)/ poly(styrene‐co‐4‐vinyl pyridine) blend

The miscibility and crystallization behavior of the solution‐blended lightly sulfonated poly(phenylene oxide) (SPPO)/poly(styrene‐co‐4‐vinylpyridine) (PSVP) blend were investigated by conventional and modulated differential scanning calorimetry (MDSC). It was found that the original blend film is actually composed of a crystalline SPPO phase and a noncrystalline compatible SPPO–PSVP phase. The original phase‐segregated structure will evolve to a noncrystalline homogenous structure by subsequent high temperature annealing. The resulting good miscibility was attributed to two aspects: one is that the SPPO crystalline structure could be destroyed as annealing temperature is high enough; the other is that the acid–base interaction between the sulfonic group of SPPO and the pyridine ring of PSVP could promote mixing of different components effectively. And such acid–base interaction was demonstrated by ¹C NMR spectra. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 2843–2848, 2001     

Determination of exchange enthalpy and entropy parameters of the equation‐of‐state theory for poly(dimethyl siloxane) and some aromatic solvents by inverse gas chromatography

The specific retention volumes, V_g^o of toluene, ethyl benzene, n‐propyl benzene and isopropyl benzene on poly(dimethyl siloxane)(PDMS) were measured at temperatures between 333 and 403 K by inverse gas chromatography. The parameters of hard‐core interaction, χ_t^∞, effective exchange energy, X ₁₂, exchange enthalpy, X₁₂, and exchange entropy, Q₁₂ in the equation‐of‐state theory were determined. The parameters χ_t^∞ of the isopropyl benzene‐PDMS pair decreased from 0.65 to 0.60 while those of others decreased from around 0.77 to 0.69 with increasing temperature. The values of the parameters X₁₂ also decreased as molecular weight of the substituted aliphatic group on the benzene ring of the solvent increased, ie 15 J cm⁻³ in toluene and 5 J cm⁻³ in isopropyl benzene. Both X₁₂ and Q₁₂ show negligible dependence on temperature. © 2000 Society of Chemical Industry     

Decreasing miscibility with greater heterogeneity in ternary polymer blend: poly(cyclohexyl methacrylate), poly(α‐methyl styrene) and poly(4‐methyl styrene)

A ternary blend system comprising poly(cyclohexyl methacrylate) (PCHMA), poly(α‐methyl styrene) (PαMS) and poly(4‐methyl styrene) (P4MS) was investigated by thermal analysis, optical and scanning electron microscopy. Ternary phase behaviour was compared with the behaviour for the three constituent binary pairs. This study showed that the ternary blends of PCHMA/PαMS/P4MS in most compositions were miscible, with an apparent glass transition temperature (T_g) and distinct cloud‐point transitions, which were located at lower temperatures than their binary counterparts. However, in a closed‐loop range of compositions roughly near the centre of the triangular phase diagram, some ternary blends displayed phase separation with heterogeneity domains of about 1 µm. Therefore, it is properly concluded that ternary PCHMA/PαMS/P4M is partially miscible with a small closed‐loop immisciblity range, even though all the constituent binary pairs are fully miscible. Thermodynamic backgrounds leading to decreased miscibility and greater heterogeneity in a ternary polymer system in comparison with the binary counterparts are discussed. © 2003 Society of Chemical Industry     

Miscible blends containing bacterial poly(3‐hydroxyvalerate) and poly(p‐vinyl phenol)

The miscibility of poly(3‐hydroxyvalerate) (PHV)/poly(p‐vinyl phenol) (PVPh) blends has been studied by differential scanning calorimetry (DSC) and Fourier transform infrared (FTIR) spectroscopy. The blends are miscible as shown by the existence of a single glass transition temperature (T_g) and a depression of the equilibrium melting temperature of PHV in each blend. The interaction parameter was found to be −1.2 based on the analysis of melting point depression data using the Nishi–Wang equation. Hydrogen‐bonding interactions exist between the carbonyl groups of PHV and the hydroxyl groups of PVPh as evidenced by FTIR spectra. The crystallization of PHV is significantly hindered by the addition of PVPh. The addition of 50 wt % PVPh can totally prevent PHV from cold crystallization. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 383–388, 1999     

Synthesis and characterization of novel swelling tunable oligomeric poly(styrene‐co‐acrylamide) modified clays

The oligomeric poly(styrene‐acrylamide‐vinylbenzylchloride) (P(St‐AM‐VBC)) quaternary ammonium salts have been prepared from the reactions of trimethylamine with the corresponding P(St‐AM‐VBC)s, which were synthesized by free‐radical polymerization of a mixture of styrene, acrylamide, and vinylbenzylchloride. Then the swelling tunable oligomeric poly(styrene‐co‐acrylamide) modified clays have been prepared through cation exchange of the sodium ions in the clay with the corresponding P(St‐AM‐VBC) quaternary ammonium salts. The P(St‐AM‐VBC) and its modified clays have been characterized by infrared spectra (IR), gel permeation chromatography (GPC), thermogravimetric analysis (TGA), proton nuclear magnetic resonance (¹H NMR), X‐ray diffraction (XRD), and transmission electron microscopy (TEM). The solvent‐swelling capacity of poly(styrene‐co‐acrylamide) modified clays have also been tested, and the experimental results have indicated that these clays are novel swelling tunable organic clays. XRD and TEM studies have shown that these novel swelling tunable clays are well‐intercalated or exfoliated. Furthermore, TGA analysis shows that these polymerically modified clays have high thermal stability for nanocomposites by melt blending. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Synthesis and light‐emitting properties of a novel π‐conjugated poly[di(p‐phenyleneethynylene)‐alt‐ (p‐phenylenecyanovinylene)] containing n‐octyloxy side branches

A novel π‐conjugated poly[di(p‐phenyleneethynylene)‐alt‐(p‐phenylenecyanovinylene)] having n‐octyloxy side chains (PPE‐C₈PPE‐PPV) was prepared by polymerization of the monomer DEDB with BCN. Chemical structure of the polymer obtained was confirmed by ¹H NMR, FTIR, and EA. PPE‐C₈PPE‐PPV had a molecular weight enough to fabricate the electroluminescent (EL) device, and showed a good organosolubility, excellent thermal stability, and film‐forming property. In UV absorption and PL spectra in film it showed a maximum at 430 and 543 nm, respectively, which appeared 5 and 41 nm longer wavelengths than that of the solution, respectively. HOMO, LUMO energy levels and band gap were determined to be ?5.70, ?3.29, and 2.41 eV, respectively. Two EL devices with low‐work function cathodes were fabricated with the structures of ITO/PEDOT/PPE‐C₈PPE‐PPV/cathodes (LiF/Al and Mg:Ag/Ag). The both devices exhibited a bright green light emission at 545 nm and the maximum luminescence of 197 cd/cm² (LiF/Al) and 158 cd/cm² (Mg:Ag/Ag). © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Highly efficient interpenetrating polymerization of styrene and 4‐vinylpyridine with poly(ethylene terephthalate) using benzoyl peroxide

A polymerization method for the preparation of an interpenetrating network polymer with poly(ethylene terephthalate) is reported. Two types of monomer, styrene and 4‐vinylpyridine, were chosen as hydrophobic and hydrophilic representatives, respectively, in order to show the versatility of this polymerization method. The polymer‐immobilized poly(ethylene terephthalate) samples were characterized using Fourier transform infrared spectroscopy, scanning electron microscopy and X‐ray photoelectron spectroscopy. The immobilization efficiency of styrene as a function of reaction temperature, monomer‐to‐initiator molar ratio, reaction time, addition of solvent, surface hydrophilicity and immersion in initiator was studied. The maximum immobilization percentage of styrene reaches 111%. The immobilization efficiency is proportional to polymer molecular weight and sample thickness. Based on these results, this strategy is shown to be an efficient, versatile method for preparing interpenetrating network polymers and can be used as a means to modify the structures and properties of polymeric substrates. © 2013 Society of Chemical Industry     

Dynamic mechanical properties in blends of poly(styrene‐b‐isoprene‐b‐styrene) with aromatic hydrocarbon resin

The damping properties in blends of poly(styrene‐b‐isoprene‐b‐styrene) (SIS) and hydrogenated aromatic hydrocarbon (C₉) resin were investigated by dynamic mechanical analysis. SIS exhibited two independent peaks of loss factor (tan δ) corresponding to the glass transition of polyisoprene (PI) and polystyrene (PS) segments, respectively. The addition of hydrogenated C₉ resin had a positive impact on the damping of SIS. With the increasing softening point and content of the resin, the main tan δ peak shifted to higher temperatures and the useful damping temperature range was broadened. Addition of mica or PS was found to widen the effective damping range evidently in the high‐temperature region, especially when PS was mixed in the solid state. It was concluded that the dispersed PS domains played a role of reinforcing fillers at low temperatures and served as a polymer component with a tan δ peak due to its glass transition at the high temperature. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102:4157–4164, 2006     

Thermal properties and non‐isothermal crystallization behavior of biodegradable poly(p‐dioxanone)/poly(vinyl alcohol) blends

Blends of two biodegradable semicrystalline polymers, poly(p‐dioxanone) (PPDO) and poly(vinyl alcohol) (PVA) were prepared with different compositions. The thermal stability, phase morphology and thermal behavior of the blends were studied by using thermogravimetric analysis (TGA), scanning electron microscopy (SEM) and differential scanning calorimetry (DSC). From the TGA data, it can be seen that the addition of PVA improves the thermal stability of PPDO. DSC analysis showed that the glass transition temperature (T_g) and the melting temperature (T_m) of PPDO in the blends were nearly constant and equal to the values for neat PPDO, thus suggesting that PPDO and PVA are immiscible. It was found from the SEM images that the blends were phase‐separated, which was consistent with the DSC results. Additionally, non‐isothermal crystallization under controlled cooling rates was explored, and the Ozawa theory was employed to describe the non‐isothermal crystallization kinetics. Copyright © 2006 Society of Chemical Industry     

Preparation and swelling properties of semi‐IPN hydrogels based on chitosan‐g‐poly(acrylic acid) and phosphorylated polyvinyl alcohol

The phosphorylated poly(vinyl alcohol) (P‐PVA) samples with various substitution degrees were prepared through the esterification reaction of PVA and phosphoric acid. By using chitosan (CTS), acrylic acid (AA) and P‐PVA as raw materials, ammonium persulphate (APS) as an initiator and N,N‐methylenebisacrylamide as a crosslinker, the CTS‐g‐PAA/P‐PVA semi‐interpenetrated polymer network (IPN) ssuperabsorbent hydrogel was prepared in aqueous solution by the graft copolymerization of CTS and AA and followed by an interpenetrating and crosslinking of P‐PVA chains. The hydrogel was characterized by Fourier transform infrared (FTIR), scanning electron microscopy (SEM), and differential scanning calorimetry (DSC) techniques, and the influence of reaction variables, such as the substitution degree and content of P‐PVA on water absorbency were also investigated. FTIR and DSC results confirmed that PAA had been grafted onto CTS backbone and revealed the existence of phase separation and the formation of semi‐IPN network structure. SEM observations indicate that the incorporation of P‐PVA induced highly porous structure, and P‐PVA was uniformly dispersed in the polymeric network. Swelling results showed that CTS‐g‐PAA/P‐PVA semi‐IPN superabsorbent hydrogel exhibited improved swelling capability (421 g·g^?1 in distilled water and 55 g·g^?1 in 0.9 wt % NaCl solution) and swelling rate compared with CTS‐g‐PAA/PVA hydrogel (301 g·g^?1 in distilled water and 47 g·g^?1 in 0.9 wt % NaCl solution) due to the phosphorylation of PVA. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Thermal properties of blends of poly(hydroxybutyrate‐co‐hydroxyvalerate) and poly(styrene‐co‐acrylonitrile)

Thermal properties of blends of poly(hydroxybutyrate‐co‐hydroxyvalerate) (PHBV) and poly(styrene‐co‐acrylonitrile) (SAN) prepared by solution casting were investigated by differential scanning calorimetry. In the study of PHBV‐SAN blends by differential scanning calorimetry, glass transition temperature and melting point of PHBV in the PHBV‐SAN blends were almost unchanged compared with those of the pure PHBV. This result indicates that the blends of PHBV and SAN are immiscible. However, crystallization temperature of the PHBV in the blends decreased approximately 9–15°. From the results of the Avrami analysis of PHBV in the PHBV‐SAN blends, crystallization rate constant of PHBV in the PHBV‐SAN blends decreased compared with that of the pure PHBV. From the above results, it is suggested that the nucleation of PHBV in the blends is suppressed by the addition of SAN. From the measured crystallization half time and degree of supercooling, interfacial free energy for the formation of heterogeneous nuclei of PHBV in the PHBV‐SAN blends was calculated and found to be 2360 (mN/m)³ for the pure PHBV and 2920–3120 (mN/m)³ for the blends. The values of interfacial free energy indicate that heterogeneity of PHBV in the PHBV‐SAN blends is deactivated by the SAN. This result is consistent with the results of crystallization temperature and crystallization rate constant of PHBV in the PHBV‐SAN blends. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 673–679, 2000     

Compatibility and thermal properties of poly(acrylonitrile–butadiene–styrene) copolymer blends with poly(methyl methacrylate) and poly(styrene‐co‐acrylonitrile)

The mechanical and heat‐resistant properties of acrylonitrile–butadiene–styrene (ABS) binary and ternary blends were investigated. The relationship of compatibility and properties was discussed. The results show that poly(methyl methacrylate) (PMMA) and styrene–maleic anhydride (SMA) can improve the thermal properties of conventional ABS. The Izod impact property of ABS/PMMA blends increases significantly with the addition of PMMA, whereas that of ABS/SMA blends decreases significantly with the addition of SMA. Blends mixed with high‐viscosity PMMA are characterized by higher heat‐distortion temperature (HDT), and their heat resistance is similar to that of blends mixed with SMA. For high‐viscosity PMMA, from 10 to 20%, it is clear that blends appear at the brittle–ductile transition, which is related to the compatibility of the two phases. TEM micrographs show low‐content and high‐viscosity PMMA in large, abnormally shaped forms in the matrix. Compatibility between PMMA and ABS is dependent on both the amount and the viscosity of PMMA. When the amount of high‐viscosity PMMA varied from 10 to 20 wt %, the morphology of the ABS binary blends varied from poor to satisfactory compatibility. As the viscosity of PMMA decreases, the critical amount of PMMA needed for the compatibility of the two phases also decreases. SMA, as a compatibilizer, improved the interfacial adhesiveness of ABS and PMMA, which results in PMMA having good dispersion in the matrix. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 2652–2660, 2002     

Effects of molecular weights of bioabsorbable poly(p‐dioxanone) on its crystallization behaviors

The crystallization behaviors of poly(p‐dioxanone) (PPDO) with different molecular weights (MWs) have been studied using a differential scanning calorimetry. The results showed that the MW of PPDO affects the crystallization rate and crystallinity obviously during the dynamic crystallization process. The Avrami equation has been used to analyze the overall isothermal crystallization of PPDO. Avrami exponents ranging from 2 to 3 were obtained with good fits (correlation coefficients were greater than 0.999 in all the cases) at T_c ranged from 55 to 75°C. Although no significant influence of MW on Avrami exponent has been found, the MW of PPDO plays dominant role on the rate constant k. The values of k increase with the MW in a T_c range from 55 to 75°C. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 2331–2335, 2006     

A novel resistive‐type humidity sensor based on poly(p‐diethynylbenzene)

Poly(p‐diethynylbenzene) (PDEB) synthesized with nickel catalyst Ni(CC ○ CCH)₂(PPh₃)₂ (Ni C) in dioxane–toluene mixed‐solvent system at 25°C shows a rich trans structure with pendant‐group ( ○ CCH) content of about 35% having higher molecular weight and good solubility. A novel resistive‐type humidity sensor based on PDEB is presented. Its humi‐sensing characteristics are described and discussed. The impedance of the sensor changed from ∼ 10³–10⁷ Ω in almost the whole humidity range [∼ 15–92% relative humidity (RH)], which is low compared with sensors based on other humi‐sensitive conjugate polymers, and hysteresis of no more than 3% RH was observed. The sensor prepared by Langmuir–Blodgett (LB) deposition method shows the best humidity response. An explanation of humi‐sensing behavior of PDEB is attempted by taking into account the interaction between hydrogen protons and super π‐conjugate orbits in PDEB. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 2010–2015, 1999     

Synthesis and characterization of semi‐interpenetrating networks based on poly(dimethylsiloxane) and poly(vinyl alcohol)

Semi‐interpenetrating networks (Semi‐IPNs) with different compositions were prepared from poly(dimethylsiloxane) (PDMS), tetraethylorthosilicate (TEOS), and poly(vinyl alcohol) (PVA) by the sol‐gel process in this study. The characterization of the PDMS/PVA semi‐IPN was carried out using Fourier transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), scanning electron microscopy (SEM), and swelling measurements. The presence of PVA domains dispersed in the PDMS network disrupted the network and allowed PDMS to crystallize, as observed by the crystallization and melting peaks in the DSC analyses. Because of the presence of hydrophilic (? OH) and hydrophobic (Si? (CH₃)₂) domains, there was an appropriate hydrophylic/hydrophobic balance in the semi‐IPNs prepared, which led to a maximum equilibrium water content of ～ 14 wt % without a loss in the ability to swell less polar solvents. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

The inhibitive effect of poly(p‐toluidine) on corrosion of iron in 1M HCL solutions

In recent years, polymer amines have been recognized as an excellent corrosion inhibitors for iron in acid solutions. In this work, the inhibitive effect of p‐toluidine and poly(p‐toluidine) on corrosion of iron in 1M HCl has been studied by the electrochemical methods such as impedance, linear polarization, Tafel polarization techniques. The effectiveness of poly(p‐toluidine) was found to be high in comparison with that of monomer. The results showed that p‐toluidine and poly(p‐toluidine) suppressed both cathodic and anodic processes of iron dissolution in 1M HCl. The inhibition efficiency of both p‐toluidine and poly(p‐toluidine) were found to increase with the inhibitor concentrations. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Comparison of interdiffusion at polystyrene–poly(vinyl methyl ether) and polystyrene–poly(isobutyl vinyl ether) interfaces

The effect of polymer–polymer compatibility on interdiffusion at polymer interfaces with dissimilar mobilities was investigated by attenuated total internal reflectance infrared spectroscopy. The polymer pair consisting of polystyrene and poly(vinyl methyl ether) was used to study interdiffusion at the interface of compatible polymers. The polymer pair consisting of polystyrene and poly(isobutyl vinyl ether) was used to study interdiffusion at the interface of incompatible polymers. Results indicate that the extent of interdiffusion is controlled by the polymer–polymer compatibility parameter, irrespectively of the differences in the mobility of the polymers.     

Shear flow behaviors of poly(p‐phenylene benzobisoxazole) spinning dope

In this study, the shear flow properties of Poly(p‐phenylene benzobisoxazole) (PBO)/poly(phosphoric acid) (PPA) spinning dope were studied by means of capillary rheometer. The effect of shear stress, temperature, PBO concentration, and PBO molecular weight on the apparent viscosity of PBO/PPA dope was discussed. The results showed that the apparent viscosity of the dope decreased with the increase of the shear stress and the temperature. The flow behavior index increased with the increase of temperature, which indicated that the non‐Newtonian behavior of the dope became weaker at high temperature. Moreover, it was also found that at high shear stress, the apparent viscosity of the dope was insensitive to the temperature, PBO molecular weight, and PBO concentration. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008