Synthesis and characterization of phthalonitrile resins from ortho‐linked aromatic and heterocyclic monomers

This article describes the synthesis and properties of phthalonitrile polymers prepared from three different ortho‐linked monomers, namely 2,2′‐bis(3,4‐dicyanophenoxy)biphenyl, 1,2‐bis(3,4‐dicyanophenoxy)benzene and 2,2′‐bis(3,4‐dicyanophenoxy)‐1,3,4‐oxadiazole. The resins exhibited a low complex viscosity, with a varying range of processing temperatures for all three systems. Thermogravimetric analysis showed that the synthesized polymers exhibited high thermal and thermo‐oxidative stability. The high char yields, which ranged from 64 to 69% at 900 °C under nitrogen atmosphere, and the high glass transition temperatures of the polymers indicated a high crosslinking density in the network structure. Dynamic mechanical measurements demonstrated that the fully cured monomer 2,2′‐bis(3,4‐dicyanophenoxy)‐1,3,4‐oxadiazole exhibited no change in glass transition temperature or in storage modulus up to 500 °C. © 2013 Society of Chemical Industry     

Synthesis and study of new polyamides with side oxadiazole rings

A series of six new aromatic polyamides with side oxadiazole rings has been synthesized by polycondensation reaction of aromatic diamines containing pendent substituted oxadiazole groups with a silicon‐containing diacid chloride [namely, bis(p‐chlorocarbonyl‐phenylene)diphenylsilane] or with a fluorine‐containing diacid chloride [namely, hexafluoroisopropylidene‐bis(p‐benzoyl chloride)]. All polymers were easily soluble in amidic solvents, such as N‐methylpyrrolidinone and dimethylformamide, and gave thin transparent films by casting such solutions. Very thin coatings were deposited onto silicon wafers and exhibited smooth, pinhole‐free surfaces in atomic force microscopy investigations. The polymers showed high thermal stability, with decomposition temperature >400°C. Some of them did exhibit a glass transition, in the range 152–276°C, with a reasonable interval between glass transition and decomposition. Four of these polymers showed blue photoluminescence, in the range 460–480 nm, which makes them promising candidates for future use as high‐performance materials in the construction of light‐emitting devices. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 714–721, 2003     

New poly(1,3,4‐oxadiazole)s bearing pentadecyl side chains: Synthesis and characterization

The 4‐[4′‐(Hydrazinocarbonyl)phenoxy]‐2‐pentadecylbenzohydrazide was polycondensed with aromatic diacid chlorides viz., terephthalic acid chloride (TPC), isophthalic acid chloride (IPC), and a mixture of TPC : IPC (50 : 50 mol %) to obtain polyhydrazides which on subsequent cyclodehydration reaction in the presence of phosphoryl chloride yielded new poly(1,3,4‐oxadiazole)s bearing flexibilizing ether linkages and pentadecyl side chains. Inherent viscosities of polyhydrazides and poly(1,3,4‐oxadiazole)s were in the range 0.53–0.66 dL g^?1 and 0.49–0.53 dL g^?1, respectively, indicating formation of medium to reasonably high molecular weight polymers. The number average molecular weights (M_n) and polydispersities (M_w/M_n) of poly(1,3,4‐oxadiazole)s were in the range 14,660–21,370 and 2.2–2.5, respectively. Polyhydrazides and poly(1,3,4‐oxadiazole)s were soluble in polar aprotic solvents such as N,N‐dimethylacetamide, 1‐methyl‐2‐pyrrolidinone, and N,N‐dimethylformamide. Furthermore, poly(1,3,4‐oxadiazole)s were also found to be soluble in solvents such as chloroform, dichloromethane, tetrahydrofuran, pyridine, and m‐cresol. Transparent, flexible, and tough films of polyhydrazides and poly(1,3,4‐oxadiazole)s could be cast from N,N‐dimethylacetamide and chloroform solutions, respectively. Both polyhydrazides and poly(1,3,4‐oxadiazole)s were amorphous in nature and formation of layered structure was observed due to packing of pentadecyl chains. A decrease in glass transition temperature was observed both in polyhydrazides (143–166°C) and poly(1,3,4‐oxadiazole)s (90–102°C) which could be ascribed to “internal plasticization” effect of pentadecyl chains. The T₁₀ values, obtained from TG curves, for poly(1,3,4‐oxadiazole)s were in the range of 433–449°C indicating their good thermal stability. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci 124:1281–1289, 2012     

Phthalonitrile‐containing poly(amide imide)s with nanoactuation properties

A series of aromatic poly(amide imide)s containing pendant phthalonitrile groups was prepared by solution polycondensation reaction of 4,4′‐diamino‐4″‐(3,4‐dicyanophenoxy)triphenylmethane, 1, or of different amounts of 1 and 1,3‐bis(4‐aminophenoxy)benzene, with a fluorinated imide diacid chloride, 2,2‐bis[N‐(4‐chloroformylphenyl)phthalimidyl]hexafluoroisopropane. The polymers were easily soluble in polar organic solvents, such as N‐methyl‐2‐pyrrolidone, N,N‐dimethylacetamide, N,N‐dimethylformamide, and dimethylsulfoxide. They can be cast from solutions into thin flexible films showing nanoactuation properties in the range of 120–450 nm, depending on the nitrile group content, when an electric voltage is applied on their surface. Electrical insulating properties of the polymer films were evaluated on the basis of dielectric permittivity and dielectric loss and their variation with the frequency and temperature. The values of the dielectric permittivity at 10 kHz and 20°C were in the range of 3.01–3.43. All polymers exhibited high thermal stability, decomposition temperature being above 420°C. POLYM. ENG. SCI., 2013. © 2012 Society of Plastics Engineers     

Synthesis and photoluminescent properties of poly(aryl ether)s containing alternate emitting and electron‐transporting moieties

A new diphenylbutadiene‐containing bisphenol was successfully synthesized from benzylideneaniline and 4‐propenylanisole via an anil synthetic method. A series of copoly(arylene ether)s consisting of an alternate isolated blue chromophore (diphenylbutadiene) and an electron‐transporting moiety (1,3,4‐oxadiazole) was synthesized and characterized. High molecular weight copoly(arylene ether)s with an inherent viscosity of >0.5 dL/g were prepared by the nucleophilic displacement reaction of oxadiazole‐activated bis‐fluorocompounds with bisphenols. Introduction of ether linkages into the copolymers led to an enhanced solubility in organic solvents such as N,N‐dimethylacetamide (DMAc) and N‐methyl‐2‐pyrrolidinone (NMP). The resulting copolymers can be cast into tough and transparent films. The copolymers were amorphous in structure with high glass transition temperatures ranging from 182.29 to 194.50°C. They also exhibited good thermal stability with the maximum decomposition temperatures higher than 500°C in nitrogen. The absorption peaks of these copolymers in thin films varied from 375 to 391 nm, while the photoluminescent peaks varied from 410 to 433 nm. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 1645–1651, 2003     

Phosphorus‐containing poly(ester‐imide)–polydimethylsiloxane copolymers

New phosphorus‐containing poly(ester‐imide)‐polydimethylsiloxane copolymers were prepared by solution polycondensation of 1,4‐[2‐(6‐oxido‐6H‐dibenz < c,e > < 1, 2 > oxaphosphorin‐6‐yl)]naphthalene‐bis(trimellitate) dianhydride with a mixture of an aromatic diamine (1,3‐bis(4‐aminophenoxy)benzene) and α,ω‐bis(3‐aminopropyl)oligodimethylsiloxane of controlled molecular weight, in various ratios. Poly(amic acid) intermediates were converted quantitatively to the corresponding polyimide structures using a solution imidization procedure. The polymers are easily soluble in polar organic solvents, such as N‐methyl‐2‐pyrrolidone and N,N‐dimethylformamide, as well as in less polar solvents such as tetrahydrofuran. They show good thermal stability, the decomposition temperature being above 370 °C. The glass transition temperatures are in the range 165–216 °C. Solutions of the polymers in N‐methyl‐2‐pyrrolidone exhibit photoluminescence in the blue region. Copyright © 2010 Society of Chemical Industry     

Compared properties of aromatic polyisophthalamides containing 5‐(4‐acetoxy‐benzamido) pendent groups

A series of aromatic polyamides containing 5‐(4‐acetoxy‐benzamido) pendent groups have been synthesized and their properties have been characterized and compared with those of related polyamides. The polyamides have weight‐ and number‐average molecular weights in the range of 36,680–65,700 and 12,685–35,490, respectively, and polydispersities in the range of 1.82–3.66. These polymers show good thermal stability comparable to traditional aromatic polyisophthalamides, with initial decomposition temperature between 270–320°C and glass transition temperature in the range of 230–270°C. Compared with related polyisophthalamides without any pendent groups, the present polymers show better solubility in certain solvents such as N‐methylpyrrolidinone and dimethylacetamide and can be cast from solutions into thin transparent flexible films having dielectric constants in the range of 3.42–4.27. The polymer films display remarkable hydrophilicity, which makes them potential candidates for use as advanced materials in humidity sensors. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 650–657, 2001     

Preparation and properties of polyimides based on bis[3,5‐dimethyl‐4‐(4‐aminophenoxy)phenyl]methane

A series of polyimide (PI) thin films were synthesized based on bis[3,5‐dimethyl‐4‐(4‐aminophenoxy)phenyl]methane and conventional aromatic dianhydrides. The structures and properties of the thin films were measured with Fourier transform infrared, NMR, thermogravimetric analysis, dynamic mechanical analysis, and impedance analysis. The PI films exhibited glass‐transition temperatures in the range of 211–300°C and possessed initial thermal decomposition temperature reaching up to 457–482°C in air and 461–473°C in nitrogen. Some PI films had high solubility in organic solvents such as 1‐methyl‐2‐pyrrolidinone, N,N‐dimethylformamide, N,N‐dimethylacetamide, dimethyl sulfoxide, m‐cresol, tetrahydrofuran, and CHCl₃. The mechanical properties of these films were also examined. The dielectric constants of the films were in the range of 2.8–3.3 at 25°C. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 1265–1270, 2007     

Synthesis and characterization of new poly(amide‐imide)s based on 1,4‐bis(trimellitimido)‐2,5‐dichlorobenzene

A series of new aromatic poly(amide‐imide)s were synthesized by the triphenyl phosphite‐activated polycondensation of the diimide‐diacid, 1,4‐bis(trimellitimido)‐2,5‐dichlorobenzene (I), with various aromatic diamines in a medium consisting of N‐methyl‐2‐pyrrolidone (NMP), pyridine, and calcium chloride. The poly(amide‐imide)s had inherent viscosities of 0.88–1.27 dL g⁻¹. The diimide‐diacid monomer (I) was prepared from 2,5‐dichloro‐p‐phenylenediamine with trimellitic anhydride. All the resulting polymers were amorphous and were readily soluble in a variety of organic solvents, including NMP and N,N‐dimethylacetamide. Transparent, flexible, and tough films of these polymers could be cast from N,N‐dimethylacetamide or NMP solutions. Cast films had tensile strengths ranging from 92 to 127 MPa, elongations at break from 4 to 24%, and initial moduli from 2.59 to 3.65 GPa. The glass transition temperatures of these polymers were in the range of 256°–317°C, and the 10% weight loss temperatures were above 430°C in nitrogen. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 73: 271–278, 1999     

Synthesis and properties of novel polyamides containing sulfone‐ether linkages and xanthene cardo groups

In order to obtain polyamides with enhanced solubility and processability, as well as good mechanical and thermal properties, several novel polyamides containing sulfone‐ether linkages and xanthene cardo groups based on a new diamine monomer, 9,9‐bis[4‐(4‐aminophenoxy)phenyl]xanthene (BAPX), were investigated. The BAPX monomer was synthesized via a two‐step process consisting of an aromatic nucleophilic substitution reaction of readily available 4‐chloronitrobenzene with 9,9‐bis(4‐hydroxyphenyl)xanthene in the presence of potassium carbonate in N,N‐dimethylformamide, followed by catalytic reduction with hydrazine and Pd/C. Four novel aromatic polyamides containing sulfone‐ether linkages and xanthene cardo groups with inherent viscosities between 0.98 and 1.22 dL g^?1 were prepared by low‐temperature polycondensation of BAPX with 4,4′‐sulfonyldibenzoyl chloride, 4,4′‐[sulfonyl‐bis(4‐phenyleneoxy)]dibenzoyl chloride, 3,3′‐[sulfonyl‐bis(4‐phenyleneoxy)]dibenzoyl chloride and 4,4′‐[sulfonyl‐bis(2,6‐dimethyl‐1,4‐phenyleneoxy)]dibenzoyl chloride in N,N‐dimethylacetamide (DMAc) solution containing pyridine. All these new polyamides were amorphous and readily soluble in various polar solvents such as DMAc and N‐methylpyrrolidone. These polymers showed relatively high glass transition temperatures in the range 238–298 °C, almost no weight loss up to 450 °C in air or nitrogen atmosphere, decomposition temperatures at 10% weight loss ranging from 472 to 523 °C and 465 to 512 °C in nitrogen and air, respectively, and char yields at 800 °C in nitrogen higher than 50 wt%. Transparent, flexible and tough films of these polymers cast from DMAc solution exhibited tensile strengths ranging from 78 to 87 MPa, elongations at break from 9 to 13% and initial moduli from 1.7 to 2.2 GPa. Primary characterization of these novel polyamides shows that they might serve as new candidates for processable high‐performance polymeric materials. Copyright © 2010 Society of Chemical Industry     

Synthesis and characterization of novel wholly para‐oriented aromatic polyamide‐hydrazides containing sulfone‐ether linkages

Four novel wholly para‐oriented aromatic polyamide‐hydrazides containing flexibilizing sulfone‐ether linkages in their main chains have been synthesized from 4‐amino‐3‐hydroxy benzhydrazide (4A3HBH) with either 4,4′‐sulfonyldibenzoyl chloride (SDBC), 4,4′‐[sulfonylbis(1,4‐phenylene)dioxy]dibenzoyl chloride (SODBC), 4,4′‐[sulfonylbis(2,6‐dimethyl‐1,4‐phenylene)dioxy]dibenzoyl chloride (4MeSODBC), or 4,4′‐(1,4‐phenylenedioxy)dibenzoyl chloride (ODBC) via a low‐temperature solution polycondensation reaction. A polyamide‐hydrazide without the flexibilizing linkages is also investigated for comparison. It was synthesized from 4A3HBH and terephthaloyl chloride (TCl) by the same synthetic route. The intrinsic viscosities of the polymer ranged from 2.85 to 4.83 dL g^?1 in N,N‐dimethyl acetamide (DMAc) at 30°C and decreased with introducing the flexibilizing linkages into the polymer. All the polymers were soluble in DMAc, N,N‐dimethyl formamide (DMF), and N‐methyl‐2‐pyrrolidone (NMP), and their solutions could be cast into films with good mechanical strengths. Further, they exhibited a great affinity to water sorption. Their solubility and hydrophilicity increased remarkably by introducing the flexibilizing linkages. The polymers could be thermally cyclodehydrated into the corresponding poly(1,3,4‐oxadiazolyl‐benzoxazoles) approximately in the region of 295–470°C either in nitrogen or in air atmospheres. The flexibilizing linkages improve the solubility of the resulting poly(1,3,4‐oxadiazolyl‐benzoxazoles) when compared with poly(1,3,4‐oxadiazolyl‐benzoxazoles) free from these linkages. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Polyamides obtained by direct polycondesation of 4‐[4‐[9‐[4‐(4‐aminophenoxy)‐3‐methyl‐phenyl] fluoren‐9‐YL]‐2‐methyl‐phenoxy]aniline with dicarboxylic acids based on a diphenyl‐silane moiety

Polyamides (PAs) containing fluorene, oxyether, and diphenyl‐silane moieties in the repeating unit were synthesized in > 85% yield by direct polycondesation between a diamine and four dicarboxylic acids. Alternatively, one PA was synthesized from an acid dichloride. The diamine 4‐[4‐[9‐[4‐(4‐aminophenoxy)‐3‐methyl‐phenyl]fluoren‐9‐yl]‐2‐methyl‐phenoxy]aniline ( 3 ) was obtained from the corresponding dinitro compound, which was synthesized by nucleophilic aromatic halogen displacement from p‐chloronitrobenzene and 9,9‐bis (4‐hydroxy‐3‐methyl‐phenyl)fluorene ( 1 ). Monomers and polymers were characterized by FTIR and ¹H, ¹³C, and ²⁹Si‐NMR spectroscopy and the results were in agreement with the proposed structures. PAs showed inherent viscosity values between 0.14 and 0.43 dL/g, indicative of low molecular weight species, probably of oligomeric nature. The glass transition temperature (T_g) values were observed in the 188–211°C range by DSC analysis. Thermal decomposition temperature (TDT_10%) values were above 400°C due to the presence of the aromatic rings in the diamine. All PAs showed good transparency in the visible region (>88% at 400 nm) due to the incorporation of the fluorene moiety. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Synthesis and properties of polyamides based on 5,5′‐bis[4‐(4‐aminophenoxy)phenyl]‐hexahydro‐4,7‐methanoindan

A new diamine 5,5′‐bis[4‐(4‐aminophenoxy)phenyl]‐hexahydro‐4,7‐methanoindan ( 3 ) was prepared through the nucleophilic displacement of 5,5′‐bis(4‐hydroxylphenyl)‐hexahydro‐4,7‐methanoindan ( 1 ) with p‐halonitrobenzene in the presence of K₂CO₃ in N,N‐dimethylformamide (DMF), followed by catalytic reduction with hydrazine and Pd/C in ethanol. A series of new polyamides were synthesized by the direct polycondensation of diamine 3 with various aromatic dicarboxylic acids. The polymers were obtained in quantitative yields with inherent viscosities of 0.76–1.02 dl g⁻¹. All the polymers were soluble in aprotic dipolar solvents such as N,N‐dimethylacetamide (DMAc) and N‐methyl‐2‐pyrrolidone (NMP), and could be solution cast into transparent, flexible and tough films. The glass transition temperatures of the polyamides were in the range 245–282 °C; their 10% weight loss temperatures were above 468 °C in nitrogen and above 465 °C in air. © 2000 Society of Chemical Industry     

Synthesis and study of new fluorinated poly(imide‐amide)s

New fluorinated poly(imide‐amide)s have been synthesized by solution polycondensation of various aromatic diamines containing a naphthalene unit with diacid chlorides having both imide and hexafluoroisopropylidene (6F) groups. These polymers are soluble in polar aprotic solvents, such as N‐methylpyrrolidone (NMP) or N,N‐dimethylformamide (DMF), and can be cast into flexible thin films from solutions. They show high thermooxidative stability with decomposition temperatures being above 425°C and glass transition temperatures being in the range of 235–305°C. The polymer films exhibit a low dielectric constant and tough mechanical properties.     

Synthesis of oxadiazole‐based polymers containing a carbazole–vinylene or fluorene–vinylene group and their hole‐injection/transport behavior in light‐emitting diodes

A series of conjugated (poly{N‐(2‐ethylhexyl)‐3,6‐carbazole–vinylene‐alt‐[(2,5‐bisphenyl)‐1,3,4‐oxadiazole]}) and nonconjugated (poly{N‐(2‐ethylhexyl)‐3,6‐carbazole–vinylene‐alt‐[(2,5‐bisphenol)‐1,3,4‐oxadiazole]}) and poly{9,9‐dihexyl‐2,7‐fluorene–vinylene‐alt‐[(2,5‐bisphenol)‐1,3,4‐oxadiazole]}) polymers containing oxadiazole and carbazole or fluorene moieties in the polymer backbone were synthesized with a multiple‐step procedure. The properties of the polymers, including the photophysical and electrochemical characteristics, could be fine‐tuned by adjustment of the components or structures in the polymer chains. The polymers were used to examine the hole‐injection/transport behavior as hole‐injection/hole‐transport layers in double‐layer indium tin oxide (ITO)/polymer/aluminum tris(8‐hydroxyquinoline)/LiF/Al devices by the determination of their energy levels. The effects of the polymers in these devices on the charge‐transport behavior were compared with a control device fabricated with poly(ethylenedioxythiophene) (PEDOT)–poly(styrene sulfonate) (PSS). Devices containing the synthesized polymers showed comparable adhesion to the ITO anode and good hole‐injection/transport performance. In addition, they exhibited higher electroluminescence over an identical range of current densities than the control device. This was attributed to the prevention of radiative exciton quenching caused by the PEDOT–PSS interfaces and the improvement of electron/exciton blocking due to the higher electron affinity of the synthesized polymers. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Novel low‐dielectric‐constant copolyimide thin films composed with SiO2 hollow spheres

A series of copolyimide/SiO₂ hollow sphere thin films were prepared successfully based on bis[3,5‐dimethyl‐4‐(4‐aminophenoxy)phenyl]methane and 9,9‐bis(4‐(4‐aminophenoxy)phenyl)fluorene (molar ratio = 3 : 1) as diamine, and 4,4′‐(4,4′‐isopropylidenediphenoxy)bis(phthalic anhydride) as dianhydride, with different wt % SiO₂ hollow sphere powder with particle size 500 nm. Some films possessed excellent dielectric properties, with ultralow dielectric constants of 1.8 at 1 MHz. The structures and properties of the thin films were measured with Fourier transform infrared spectra, scanning electron microscope, thermogravimetric analysis, and dynamic mechanical thermal analysis. The polyimide (PI) films exhibited glass‐transition temperatures in the range of 209– 273°C and possessed initial thermal decomposition temperature reaching up to 413–477°C in air and 418–472°C in nitrogen. Meanwhile, the composite films were also exhibited good mechanical properties. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Synthesis and characterization of novel aromatic polyamides derived from 2,2′‐bis(p‐phenoxyphenyl)‐4, 4′‐diaminodiphenyl ether

BACKGROUND: Wholly aromatic polyamides (aramids) are high‐performance polymeric materials with outstanding heat resistance and excellent chemical stabilities due to chain stiffness and intermolecular hydrogen bonding of amide groups. Synthesis of structurally well‐designed monomers is an effective strategy to prepare modified forms of these aramids to overcome lack of organo‐solubility and processability limitations. RESULTS: A novel class of wholly aromatic polyamides was prepared from a new diamine, namely 2,2′‐bis(p‐phenoxyphenyl)‐4,4′‐diaminodiphenyl ether (PPAPE), and two simple aromatic dicarboxylic acids. Two reference polyamides were also prepared by reacting 4,4′‐diaminodiphenyl ether with the same comonomers under similar conditions. M?_w and M?_n of the resultant polymers were 8.0 × 10⁴ and 5.5 × 10⁴ g mol^?1, respectively. Polymers resulting from PPAPE exhibited a nearly amorphous nature. These polyamides exhibited excellent organo‐solubility in a variety of polar solvents and possessed glass transition temperatures up to 200 °C. The 10% weight loss temperatures of these polymers were found to be up to 500 °C under a nitrogen atmosphere. The polymers obtained from PPAPE could be cast into transparent and flexible films from N,N‐dimethylacetamide solution. CONCLUSION: The results obtained show that the new PPAPE diamine can be considered as a good monomer to enhance the processability of its resultant aromatic polyamides while maintaining their high thermal stability. The observed characteristics of the polyamides obtained make them promising high‐performance polymeric materials. Copyright © 2009 Society of Chemical Industry     

Polyimides derived from 1,4‐bis [3‐oxy‐(N‐aminophthalimide)] benzene

A novel diamine, 1,4‐bis [3‐oxy‐(N‐aminophthalimide)] benzene (BOAPIB), was synthesized from 1,4‐bis [3‐oxy‐(N‐phenylphthalimide)] benzene and hydrazine. Its structure was determined via IR, ¹H NMR, and elemental analysis. A series of five‐member ring, hydrazine‐based polyimides were prepared from this diamine and various aromatic dianhydrides via one‐step polycondensation in p‐chlorophenol. The inherent viscosities of these polyimides were in the range of 0.17–0.61 dL/g. These polymers were soluble in polar aprotic solvents and phenols at room temperature. Thermogravimetric analysis (TGA) showed that the 5% weight‐loss temperatures of the polyimides were near 450°C in air and 500°C in nitrogen. Dynamic mechanical thermal analysis (DMTA) indicated that the glass‐transition temperatures (T_gs) of these polymers were in the range of 265–360°C. The wide‐angle X‐ray diffraction showed that all the polyimides were amorphous. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Synthesis and characterization of polyamides and poly(amide‐imide)s derived from 2,6‐bis(3‐aminophenoxy)benzonitrile or 2,6‐bis(4‐aminophenoxy)benzonitrile

A series of polyamides and poly(amide‐imide)s was prepared by direct polycondensation of ether and nitrile group containing aromatic diamines with aromatic dicarboxylic acids and bis(carboxyphthalimide)s respectively in N‐methyl 2‐pyrrolidone (NMP) using triphenyl phosphite and pyridine as condensing agents. New diamines, such as 2,6‐bis(4‐aminophenoxy)benzonitrile and 2,6‐bis(3‐aminophenoxy)benzonitrile, were prepared from 2,6‐dichlorobenzonitrile with 4‐aminophenol and 3‐aminophenol, respectively, in NMP using potassium carbonate. Bis(carboxyphthalimide)s were prepared from the reaction of trimellitic anhydride with various aromatic diamines in N,N′‐dimethyl formamide. The inherent viscosities of the resulting polymers were in the range of 0.27 to 0.93 dl g^?1 in NMP and the glass transition temperatures were between 175 and 298 °C. All polymers were soluble in dipolar aprotic solvents such as dimethylsulfoxide, dimethylacetamide and NMP. All polymers were stable up to 350 °C with a char yield of above 40 % at 900 °C in nitrogen atmosphere. All polymers were found to be amorphous except the polyamide derived from isophthalic acid and the poly(amide‐imide)s derived from diaminodiphenylether and diaminobenzophenone based bis(carboxyphthalimide)s. Copyright © 2004 Society of Chemical Industry     

Synthesis of soluble and thermally stable poly(N‐arylenebenzimidazole)s

Six new bis(benzimidazolyl) monomers containing ether, sulfonyl and ketone groups were synthesized efficiently. A series of poly(N‐arylenebenzimidazole)s were prepared using an aromatic nucleophilic displacement reaction that removed the N–H sites from the novel bis(benzimidazolyl) derivatives with activated aromatic difluorides in sulfolane. The reaction was carried out at 210 °C in the presence of anhydrous potassium carbonate. All resulting polymers showed essentially amorphous patterns. This was consistent with the calculated results. Differential scanning calorimetry and thermogravimetric measurements showed that the polymers had high glass transition temperatures (>240 °C), good thermostability and high decomposition temperatures (>400 °C). These novel polymers also showed easy solubility. © 2013 Society of Chemical Industry