Poly[2-(hydroxyethyl methacrylate)-co-(sulfobetaine)]s hydrogels: 1. Synthesis and swelling behaviors of the 2-(hydroxyethyl methacrylate)-co-2-(vinyl-1-pyridinium propane sulfonate) hydrogels

A series of the 2-hydroxyethyl methacrylate/2-vinyl-l-pyridinium propane sulfonate (HEMA/VPPS) copolymeric gels have been prepared from HEMA and zwitterionic monomer VPPS of various molar ratios. The influence of the amount of VPPS in copolymeric gels on their swelling behavior in water and various saline solutions at different temperatures was investigated. Results indicate that the PHEMA hydrogels exhibit an overshooting phenomenon in their dynamic swelling behavior. The maximum overshooting value decreases with increasing temperature. The same results are also shown for the lower VPPS content HEMA/VPPS copolymeric gels. In the equilibrium swelling ratio, the PHEMA hydrogel exhibits a minimum swelling ratio at 55 °C. Then, the minimum swelling ratio disappears gradually with increasing VPPS content in HEMA/VPPS copolymeric gels. In the saline solution, the swelling ratios of HEMA/VPPS copolymeric gels increase rapidly with increasing salt concentration, for salts with a smaller ratio of charge/radius.     

Preparation and Gel Properties of Poly[hydroxyethylmethacrylate-co-poly(ethylene glycol) methacrylate] Copolymeric Hydrogels by Photopolymerization

Copolymeric hydrogels based on 2-hydroxyethyl methacrylate (HEMA) and poly(ethylene glycol) methacrylate (PEGMA) and isopropanol as a diluent were prepared by photopolymerization. The swelling kinetics, mechanical properties, drug release behaviors, and the interaction between various drugs and the present copolymeric gels were investigated in this study. The results showed that the addition of PEGMA could effectively increase the equilibrium water content and the diffusion coefficient and penetration velocity of water though the gels. Although Young's modulus increased with the increase of PEGMA content, the resulting gels had smaller elongation and more brittle characteristics. The drug release behavior was strongly dependent on the interaction between the present copolymeric gels and drugs such as caffeine, crystal violet (CV), phenol red, and vitamin B₁₂.     

Synthesis and swelling properties of 2‐hydroxyethyl methacrylate‐co‐1‐vinyl‐3‐(3‐sulfopropyl)imidazolium betaine hydrogels

A series of 2‐hydroxyethyl methacrylate/1‐vinyl‐3‐(3‐sulfopropyl)imidazolium betaine (HEMA/VSIB) copolymeric gels were prepared from various molar ratios of HEMA and the zwitterionic monomer VSIB. The influence of the amount of VSIB in copolymeric gels on their swelling behavior in water and various saline solutions at different temperatures and the drug‐release behavior, compression strength, and crosslinking density were investigated. Experimental results indicated that the PHEMA hydrogel and the lower VSIB content (3%) in the HEMA/VSIB gel exhibited an overshooting phenomenon in their dynamic swelling behavior, and the overshooting ratio decreased with increase of the temperature. In the equilibrium water content, the value increased with increase of the VSIB content in HEMA/VSIB hydrogels. In the saline solution, the water content for these gels was not affected by the ion concentration when the salt concentration was lower than the minimum salt concentration (MSC) of poly(VSIB). When the salt concentration was higher than the MSC of poly(VSIB), the deswelling behavior of the copolymeric gel was more effectively suppressed as more VSIB was added to the copolymeric gels. However, the swelling behavior of gels in KI, KBr, NaClO₄, and NaNO₃ solutions at a higher concentration would cause an antipolyelectrolyte phenomenon. Besides, the anion effects were larger than were the cation effects in the presence of a common anion (Cl^?) with different cations and a common cation (K⁺) with different anions for the hydrogel. In drug‐release behavior, the addition of VSIB increased the drug‐release ratio and the release rate. Finally, the addition of VSIB in the hydrogel improved the gel strength and crosslinking density of the gel. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 2888–2900, 2001     

Tuning the thermoresponsive properties of poly(oligo(propylene glycol) methacrylate) hydrogels via gradient copolymerization with 2-hydroxyethyl methacrylate

Gamma radiation was used to prepare copolymer hydrogel libraries based on oligo(propylene glycol) methacrylate (OPGMA) and 2-hydroxyethyl methacrylate (HEMA); a complete screening in composition of P(OPGMA/HEMA) copolymers was elaborated from 0% to 100% of OPGMA. Determination of gel fraction was performed as the first step after radiation induced synthesis. Tuning of the volume phase transition temperature (VPTT) of P(OPGMA/HEMA) copolymeric hydrogels was investigated by swelling study. Additional characterization of structure and properties was conducted by FTIR, DSC, and UV-Vis spectroscopy. All results indicate that new P(OPGMA/HEMA) copolymeric hydrogels have wide diversity in thermoresponsive properties which strongly depend on their composition.     

Superabsorbent polymeric materials. I. Swelling behaviors of crosslinked poly(sodium acrylate-co-hydroxyethyl methacrylate) in aqueous salt solution

A series of crosslinked poly(sodium acrylate-co-hydroxyethyl methacrylate) based on sodium acrylate (SA), 2-hydroxyethyl methacrylate (HEMA), and N,N′-methylene-bis-acrylamide (NMBA) are prepared by inverse suspension polymerization. The resultant crosslinking polymers are xerogellants. This work investigates not only the absorbency or swelling behavior for these xerogellants composed of different ratios of HEMA/SA in water, but also the effects of various salts and pH values on the swelling properties. Experimental results indicate that the absorbency in deionized water decreases with an increase in the HEMA in copolymeric gel, which is related to the degree of expansion of the network and the strength of the hydrophilic group. The absorbency in the chloride salt solutions decreases with an increase in the salt concentration (swelling is 50 times for the IA group chloride salt solutions, but is less than 5 times for the IIA group salt solution), owing to the osmosis of water and ions between the polymeric gel and the external solution. A decrease in the extent of swelling occurs for divalent and trivalent chloride salt solutions. For the salt solutions of the same ionic strength, the swelling amount has the following tendency: LiCl(aq) = NaCl(aq) = KCl(aq), CaCl₂(aq) < SrCl₂(aq) < BaCl₂(aq), and Fe³⁺ > Ca²⁺ > Zn²⁺ > Cu²⁺. These orders are related to the complexing ability between metallic cations and the carboxylate group in the polymeric chains. Finally, the adsorption of ferric ion by these gels is also investigated. © 1996 John Wiley & Sons, Inc.     

pH‐reversible hydrogels. IV. Swelling behavior of the 2‐hydroxyethyl methacrylate‐co‐acrylic acid‐co‐sodium acrylate copolymeric hydrogels

A series of 2‐hydroxyethyl methacrylate (HEMA) and sodium acrylate (SA50) copolymeric gels were prepared from HEMA and the anionic monomer SA50 with various molar ratios. The influence of SA50 on the copolymeric gels on their swelling behavior in deionized water at different temperatures and various pH buffer solutions was investigated. Results indicated that the poly(2‐hydroxyethyl methacrylate) (PHEMA) hydrogels exhibited an overshooting phenomenon in their dynamic swelling behavior. The maximum overshooting value decreased with increasing of the temperature. The same results were also found in the HEMA/SA50 copolymeric gels with a lower SA50 content. On the contrary, the overshooting phenomenon for HEMA/SA50 copolymeric gels with a higher content of SA50 was exhibited only under higher temperature (over 35°C). These copolymer gels were used to assess drug release and drug delivery in this article. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 1360–1371, 2001     

Effect of Silicon Monomers on the Swelling and Mechanical Properties of (PEGMA-co-HEMA) Hydrogels

A series of novel copolymeric hydrogels were prepared from 2-hydroxyethylmethacrylate (HEMA) and poly(ethyleneglycol) methacrylate (PEGMA), and silicon monomers such as trimethylsilylmethacrylate (TMSM) and 2-(trimethylsilyloxy) ethyl methacrylate (TMSOE). The effect of silicon monomer on the swelling and mechanical properties of the hydrogels was examined. The results showed that the addition of silicon monomers lowered the equilibrium water content of (PEGMA-co-HEMA) hydrogels due to their lower hydrophilicities than PEGMA and HEMA. From the swelling kinetics data, it was found that the hydrophobicity of TMSM is larger than TMSOE. The addition of TMSM effectively lowered Young's modulus and increased elongation of the synthesized hydrogels. The hydrogels containing TMSM showed pH-sensitivities, but those containing TMSOE showed a good stability in acid and base solutions.     

Poly(2-hydroxyethyl methacrylate-co-sulfobetaine) hydrogels. II. Synthesis and swelling behaviors of the [2-hydroxyethyl methacrylate-co-3-dimethyl(methacryloyloxyethyl)ammonium propane sulfonate] hydrogels

A series of the 2-hydroxyethyl methacrylate/3-dimethyl-(methacryloyloxyethyl)ammonium propane sulfonate (HEMA/DMAPS) copolymeric gels was prepared from various molar ratios of HEMA and the zwitterionic monomer DMAPS. The influence of the amount of the zwitterionic monomer in the copolymeric gels on the swelling behaviors in water, various saline solutions, and temperature was investigated. The results indicate that the PHEMA hydrogel (D0) and lower DMAPS content of the HEMA/DMAPS copolymeric gel (D1) exhibit overshooting phenomena in the dynamic swelling behavior. The maximum overshooting value decreases with increase in temperature. In the equilibrium swelling ratio, the PHEMA hydrogel exhibits a minimum swelling ratio at 55°C. Then, the minimum swelling ratio diminishes gradually with increasing of the DMAPS content in the HEMA/DMAPS copolymeric gels. In the saline solution, the swelling ratios of HEMA/DMAPS copolymeric gels increase rapidly with increasing of concentration of the salt with a smaller ratio of the charge/radius. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 69: 2021–2034, 1998     

Radiation synthesis, characterisation and antimicrobial application of novel copolymeric silver/poly(2-hydroxyethyl methacrylate/itaconic acid) nanocomposite hydrogels

Silver nanoparticles were fabricated via in situ reduction of silver nitrate embedded in swollen P(HEMA/IA) hydrogel, using gamma radiolysis method. Copolymeric hydrogels based on 2-hydroxyethyl methacrylate (HEMA) and itaconic acid (IA), previously synthesised by gamma radiation for wound dressing application, were used as a carrier and a stabilising agent, while ethyl alcohol was used as a free radical scavenger. The influence of different P(HEMA/IA) hydrogels and silver salt concentrations on the size and distribution of nanoparticles was investigated. The Ag/P(HEMA/IA) nanocomposites were characterised by high resolution scanning electron microscopy, energy dispersive spectroscopy, wide-angle X-ray diffraction, UV-Vis spectroscopy and swelling measurements. Escherichia coli (Gram-negative bacterium), Staphylococcus aureus (Gram-positive bacterium) and Candida albicans (fungus) were used to prove the antimicrobial properties of Ag/P(HEMA/IA) nanocomposites. The inhibition kinetics of bacteria growth was investigated by measuring the colony-forming unit. The antimicrobial effectiveness of the Ag/P(HEMA/IA) hydrogel nanocomposite was demonstrated even at small silver concentrations. P(HEMA/IA) hydrogels containing nanosilver particles was found suitable to be used as wound dressing.     

pH‐thermoreversible hydrogels. I. Synthesis and swelling behaviors of the (N‐isopropylacrylamide‐co‐acrylamide‐co‐2‐hydroxyethyl methacrylate) copolymeric hydrogels

A series of pH‐thermoreversible hydrogels that exhibited volume phase transition was synthesized by various molar ratios of N‐isopropylacrylamide (NIPAAm), acrylamide (AAm), and 2‐hydroxyethyl methacrylate (HEMA). The influence of environmental conditions such as temperature and pH value on the swelling behavior of these copolymeric gels was investigated. Results showed that the hydrogels exhibited different equilibrium swelling ratios in different pH solutions. Amide groups could be hydrolyzed to form negatively charged carboxylate ion groups in their hydrophilic polymeric network in response to an external pH variation. The pH sensitivities of these gels also depended on the AAm content in the copolymeric gels; thus the greater the AAm content, the higher the pH sensitivity. These hydrogels, based on a temperature‐sensitive hydrogel, demonstrated a significant change of equilibrium swelling in aqueous media between a highly solvated, swollen gel state and a dehydrated network response to small variations of temperature. pH‐thermoreversible hydrogels were used for a study of the release of a model drug, caffeine, with changes in temperature. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 71: 221–231, 1999     

Superabsorbent polymeric materials. XIII. Effect of oxyethylene chain length on water absorbency for the sodium acrylate and poly(ethylene glycol) methyl ether acrylate (PEGMEAn) copolymeric gels

In a previous study, we prepared a series of xerogels based on sodium acrylate (NaA) and 2‐hydroxyethyl methacrylate (HEMA, OE = 1) or poly(ethylene glycol) methacrylate (PEGMA, OE = 6) with different oxyethylene (OE) units. The effect of the contents of HEMA and PEGMA in the copolymeric gel on the swelling behavior in deionized water and various saline solutions was studied. Their results showed that the water absorbencies for these two series gels were effectively improved by adding a small amount of HEMA or PEGMA. In this article, a series of novel xerogels based on NaA and hydrophilic monomer poly(ethylene glycol) methyl ether acrylate (PEGMEA_n), which was synthesized from acryloyl chloride and poly(ethylene glycol) monomethyl ether with three oxyethylene (OE = 9, 16, 45) chain lengths, were prepared by inverse suspension polymerization. The effects of OE chain length in the copolymeric gel on the water absorption behavior and initial absorption rate for the present xerogels were investigated. Results showed that adding a small amount of PEGMEA_n could effectively increase the water absorbency of the gels. In addition, the water absorbency decreased with an increase of the OE chain length in PEGMEA_n. The initial absorption rate for the present copolymeric gels increased with increasing OE chain length in PEGMEA_n and the content of PEGMEA_n in the copolymeric gels. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 927–934, 2006     

Studies on swelling behaviors,mechanical properties,network parameters and thermodynamic interaction of water sorption of 2-hydroxyethyl methacrylate/novolac epoxy vinyl ester resin copolymeric hydrogels

A series of the highly cross-linked hydrogels has been developed by the syntheses of bulk copolymers based on 2-hydroxyethyl methacrylate (HEMA) and novolac epoxy vinyl ester resin (NEVER). The resulting hydrogels were investigated on their equilibrium water content (EWC), swelling behaviors and tensile properties. Dynamic swelling behaviors of copolymeric hydrogels indicate that the swelling process of these polymers follows Fickian behavior. The EWC decreased and volume fraction of polymer in hydrogel (ϕ₂) increased with NEVER content increasing due to its hydrophobicity. The increase of ionic strength of swelling medium or temperature results in a decrease in EWC and an increase in values of ϕ₂. Young’s modulus and tensile strength of hydrogels, as well as effective cross-link density (v_e), increased as NEVER content increased or ionic strength of swelling medium increased, attributing to increasing interaction between hydrophobic groups and polymer–polymer interaction with an increase in NEVER content or in ionic strength. The polymer–solvent interaction parameter χ reflecting thermodynamic interaction was also studied. As NEVER content, ionic strength of swelling medium or temperature increased, the values of χ increased. The values of χ and its two components χ_H and χ_S varied with increasing T. The negative values and trend of the enthalpy and entropy of dilution derived from values of χ_H and χ_S, could be explained on the basis of structuring of water through improved hydrogen bonding and hydrophobic interaction.     

Biocompatible and bioadhesive hydrogels based on 2-hydroxyethyl methacrylate, monofunctional poly(alkylene glycol)s and itaconic acid

Summary Novel poly(Bisomer/HEMA/IA) hydrogels were prepared by radical copolymerization of poly(alkylene glycol) (meth)acrylates, i.e. short chains Bisomers, 2-hydroxyethyl methacrylate (HEMA) and itaconic acid (IA) in a mixture of water/ethanol as solvent. These hydrogels were characterized in terms of swelling in conditions similar to the biological fluids (pH range 2.20–7.40 buffer solutions), compression-strain measurements, thermal properties and morphology. The influence of the type of Bisomer and of the itaconic acid on swelling and mechanical properties, as well as on morphology and thermal behavior of the resulting hydrogels, were investigated. The in vitro study of biocompatibility, carried out with the hydrogels containing different types of Bisomers, showed no evidence of cell toxicity nor any considerable hemolytic activity. All hydrogels showed satisfactory bioadhesive properties, so these materials have potential as drug carriers or biological glue and sealants.     

Effect of porosigen and hydrophobic monomer on the fast swelling–deswelling behaviors for the porous thermoreversible copolymeric hydrogels

A series of porous thermoreversible copolymeric hydrogels were prepared from N‐isopropylacrylamide (NIPAAm) and hydrophobic monomers such as 2,2,3,3,4,4,5,5‐octafluoropentyl methacrylate (OFPMA) and n‐butyl methacrylate (BMA) and CaCO₃ or poly(ethylene glycol) 8000 (PEG8000) as porosigen by emulsion polymerization. The effect of hydrophobic monomers and porosigens on the fundamental properties, such as equilibrium swelling ratio, swelling kinetics, gel strength, crosslinked densities, etc., and fast swelling–deswelling behavior for the present copolymeric hydrogels were investigated. Results showed that the deswelling rates for the gels porosigened by CaCO₃ were more rapid than those gels foamed by PEG8000. Results also showed that the swelling rates for the gel foamed by CaCO₃ were higher than those for the gel foamed by PEG8000. At the same time, results also showed that the gels with OFPMA foamed by CaCO₃ exhibit a faster swelling–deswelling behavior than those gels with BMA. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 3152–3160, 2006     

Crosslinking behavior of dextran modified with hydroxyethyl methacrylate upon irradiation with visible light—Effect of concentration,coinitiator type,and solvent

This study presents the synthesis of a crosslinkable dextran as starting material for the development of new hydrogels as drug delivery system in dental applications. 2‐Hydroxyethyl methacrylate (HEMA) was coupled to dextran after activation with carbonyldiimidazole as monitored by FTIR and ¹H‐NMR spectroscopy. The Dex‐HEMA was crosslinked by visible light in the presence of camphorquinone (CQ) as photoinitiator and a coinitiator in a proper solvent. Aliphatic or aromatic amines were used as coinitiators and the content of the coinitiator was varied from 0.25 to 3.0 mol %. Diphenyliodonium chloride was added as a third component to the above photoinitiation system. It was observed that, the degree of swelling decreased upon an increase of Dex‐HEMA concentration and the water content in the solvent system due to formation of more crosslinking points, that is, increasing crosslink density (P_x). The type of coinitiator shows a prominent impact on the swelling behavior and crosslinking efficiency of hydrogels. Special cryofixation and cryofracture techniques were used to investigate the surface and interior of swollen Dex‐HEMA hydrogel samples by SEM. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

2,3-Dihydroxypropyl methacrylate and 2-hydroxyethyl methacrylate hydrogels: gel structure and transport properties

The drying kinetics were examined in four cross-linked polymers that form hydrogels: 2,3-Dihydroxypropyl methacrylate (DHPMA) and 2-hydroxyethyl methacrylate (HEMA) and two random copolymers, with one-to-one and three-to-one HEMA-to-DHPMA molar ratios. The hydrogels were saturated with buffered, isotonic saline solution and deionized water; weight loss kinetics were monitored at temperatures from 16 to 37 °C at 30 and 60% relative humidity under air flow. While there are numerous studies of diffusion in hydrogels, this is one of few studies examining the initial evaporative drying period. The analyses of this short time data revealed that increasing the DHPMA content decreased water volatility; the percent water loss rate decreased with DHPMA content. Long time desorption data coupled with differential scanning calorimetry (DSC) results suggest that departure from Fickian desorption kinetics coincides with the onset of non-freezing water desorption. Dynamic mechanical analysis (DMA) revealed that changes in stiffness accompanying desorption are much more pronounced in HEMA containing polymers. Preliminary results indicate that the ion transport rate is greater in DMPMA containing hydrogels.     

Synthesis and characterization of hydroxyethyl methacrylate/acrylamide responsive hydrogels

Hydrogels based on an aqueous solution of hydroxyethyl methacrylate (HEMA) and acrylamide (AM) in the presence of trithioglycolic acid (TTGA) were prepared under the effect of gamma irradiation. These hydrogels were characterized by IR spectroscopy and thermogravimetric analysis and investigated for temperature‐ and pH‐responsive materials. It was found that TTGA is essential for the formation of HEMA/AM hydrogels at different compositions, in which the gel fraction depends on composition. A binary mixture of HEMA and AM at equal ratios was the critical composition that forms hydrogels, even in the presence of TTGA. The IR spectroscopic analysis showed that the formation of hydrogels depends on hydrogen bonding and crosslinking. The TGA investigations with respect to mass loss and the temperatures of the maximum value of the rate of reaction showed that HEMA/AM hydrogels possess higher thermal stability than that of pure HEMA and this stability increases with increasing ratio of the AM component. Also, it was observed that the temperature of the maximum value of the rate of thermal decomposition reaction depends on hydrogel composition. However, calculations of the activation energy showed that the hydrogel composed of 90% HEMA and 10% AM exhibits the highest thermal stability during the increasing or decreasing rate of reaction. Kinetic studies of swelling in water showed that HEMA/AM hydrogels displayed a temperature‐responsive character within the temperature range 25–30°C, and showed a stepwise swelling behavior in the pH range 2–10, depending on composition. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 95: 1105–1115, 2005     

温度及pH敏感共聚/粘土纳米复合水凝胶的合成与性能研究

以无机粘土为交联剂制备了具有温度、pH双重敏感性的聚（N-异丙基丙烯酰胺-co-甲基丙烯酸-β-羟乙酯）/粘土纳米复合水凝胶（P（NIPA-co-HEMA）/clay）,并用红外和X衍射对其结构和形态进行了表征。在弱碱性（pH=7.4）和25℃条件下,分别研究了温度和不同pH缓冲溶液对该凝胶溶胀度的影响,测定了纳米复合水凝胶的力学性能。结果表明：水凝胶的粘土已被剥离成单片层,且均匀分散在凝胶网络中,起交联作用;P（NIPA-co-HEMA）/clay具有良好的温度、pH双重敏感特性;凝胶的断裂伸长率〉1000%。     

Thermosensitive and ampholytic hydrogels for salt solution

A series of N‐isopropylacrylamide/[[3‐(methacryloylamino)propyl]dimethy(3‐sulfopropyl)ammonium hydroxide] (NIPAAm/MPSA) copolymer hydrogels were prepared with various compositions. Swelling of the hydrogels in water, aqueous NaCl, KCl, CaCl₂, and MgCl₂ solutions was studied. NIPAAm/MPSA hydrogels have a higher degree of swelling in water and salt solutions than that of poly(N‐isopropylacrylamide) (PNIPAAm). Also, NIPAAm/MPSA hydrogels are more salt resistant when deswelling in salt solutions. For <7 mol % MPSA, the formed hydrogels retain both temperature reversibility and high swelling. A higher content of MPSA (>11 mol %) leads to better salt resistance but a decrease in thermosensitivity. The swelling of NIPAAm/MPSA hydrogel in 0.05M NaCl is non‐Fickian. In NaCl and KCl aqueous solutions, the zwitterionic hydrogels do not show obvious antipolyelectrolyte swelling behavior, whereas in divalent salt CaCl₂ and MgCl₂ solutions, the swelling ability of NIPAAm/MPSA hydrogels is enhanced at low salt concentration, then decreases with further increase in salt concentration. The lower critical solution temperatures of NIPAAm/MPSA hydrogels are also affected by concentrated salt solution. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 2032–2037, 2003     

Thermoreversible hydrogel. V. Synthesis and swelling behavior of the N-isopropylacrylamide-co-trimethyl methacryloyloxyethyl ammonium iodide copolymeric hydrogels

A series of N-isopropylacrylamide/trimethyl methacryloyloxyethyl ammonium iodide (NIPAAm/TMMAI) copolymeric gels are prepared from the various molar ratios of NIPAAm, cationic monomer TMMAI, and N,N′-methylene bisacrylamide (NMBA) in this article. The influences of the amount of the cationic monomer in the copolymeric gels on the swelling behavior in water, various saline solutions, and various temperatures are investigated. Results show that the swelling ratios of copolymeric gels are significantly larger than those of pure homopolymer NIPAAm gel, and the more the TMMAI content, the higher the gel transition temperature. In the saline solution, results show that the swelling ratio of pure NIPAAm gel has not significantly changed with an increase of the salt concentration until the salt concentration is larger than 0.1M. The swelling ratios for the copolymeric gels NIPAAm/TMMAI decrease with increasing salt concentration. In various saline solutions, results show that the anionic effects are greater than cationic effects in the presence of common anion, different cations and common cation, and different anions for these hydrogels. Finally, we also tested the reversibility of the NIPAAm/TMMAI copolymeric gels. The deswelling and reswelling kinetics are dependent on the temperature, which is below or above the gel transition temperature. The gel with little TMMAI content has a good reversibility. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 69: 1793–1803, 1998