Rational Design of High‐Mobility Semicrystalline Conjugated Polymers with Tunable Charge Polarity: Beyond Benzobisthiadiazole‐Based Polymers

High‐mobility semiconducting polymers composed of arylene vinylene and dithiophene‐thiadiazolobenzotriazole (SN) units are developed by three powerful design strategies, namely, backbone engineering, heteroatom substitution, and side‐chain engineering. First, starting from the quaterthiophene‐SN copolymer, a vinylene spacer is inserted into the quaterthiophene unit for constructing highly‐planar backbones. Second, heteroatoms (O and N atoms) are incorporated into the thienylene vinylene moieties to tune the electronic properties and intermolecular interactions. Third, the alkyl side chains are optimized to tune the solubility and self‐assembly properties. As a consequence, a remarkable thin film transistor performance is obtained. The very high hole mobility of 3.22 cm² V^?1 s^?1 is achieved for the p‐type polymer, PSNVT‐DTC8, which is the highest value ever reported for the polymers based on the benzobisthiadiazole and its analogs. Moreover, heteroatom substitution efficiently varies the charge polarity of the polymers as in the case of the N atom substituted PSNVT_z‐DTC16 displaying n‐type dominant ambipolar properties with the electron mobility of 0.16 cm² V^?1 s^?1. Further studies using grazing‐incidence wide‐angle X‐ray scattering and atomic force microscopy have revealed the high crystallinities of the polymer thin films with strong π–π interactions and suitable polymer packing orientations.     

Anisotropy of Charge Transport in a Uniaxially Aligned and Chain‐Extended,High‐Mobility,Conjugated Polymer Semiconductor

Charge transport in the ribbon phase of poly(2,5‐bis(3‐alkylthiophen‐2‐yl)thieno[3,2‐b]thiophene) (PBTTT)—one of the most highly ordered, chain‐extended crystalline microstructures available in a conjugated polymer semiconductor—is studied. Ribbon‐phase PBTTT has previously been found not to exhibit high carrier mobilities, but it is shown here that field‐effect mobilities depend strongly on the device architecture and active interface. When devices are constructed such that the ribbon‐phase films are in contact with either a polymer gate dielectric or an SiO₂ gate dielectric modified by a hydrophobic, self‐assembled monolayer, high mobilities of up to 0.4 cm² V^?1 s^?1 can be achieved, which is comparable to those observed previously in terrace‐phase PBTTT. In uniaxially aligned, zone‐cast films of ribbon‐phase PBTTT the mobility anisotropy is measured for transport both parallel and perpendicular to the polymer chain direction. The mobility anisotropy is relatively small, with the mobility along the polymer chain direction being higher by a factor of 3–5, consistent with the grain size encountered in the two transport directions.     

Eleven‐Membered Fused‐Ring Low Band‐Gap Polymer with Enhanced Charge Carrier Mobility and Photovoltaic Performance

A multi‐ring, ladder‐type low band‐gap polymer (PIDTCPDT‐DFBT) is developed to show enhanced light harvesting, charge transport, and photovoltaic performance. It possesses excellent planarity and enhanced effective conjugation length compared to the previously reported fused‐ring polymers. In order to understand the effect of extended fused‐ring on the electronic and optical properties of this polymer, a partially fused polymer PIDTT‐T‐DFBT is also synthesized for comparison. The fully rigidified polymer provides lower reorganizational energy, resulting in one order higher hole mobility than the reference polymer. The device made from PIDTCPDT‐DFBT also shows a quite promising power conversion efficiency of 6.46%. Its short‐circuit current (14.59 mA cm^?2) is also among the highest reported for ladder‐type polymers. These results show that extending conjugation length in fused‐ring ladder polymers is an effective way to reduce band‐gap and improve charge transport for efficient photovoltaic devices.     

ε‐Branched Flexible Side Chain Substituted Diketopyrrolopyrrole‐Containing Polymers Designed for High Hole and Electron Mobilities

Based on the integrated consideration and engineering of both conjugated backbones and flexible side chains, solution‐processable polymeric semiconductors consisting of a diketopyrrolopyrrole (DPP) backbone and a finely modulated branching side chain (ε‐branched chain) are reported. The subtle change in the branching point from the backbone alters the π?π stacking and the lamellar distances between polymer backbones, which has a significant influence on the charge‐transport properties and in turn the performances of field‐effect transistors (FETs). In addition to their excellent electron mobilities (up to 2.25 cm² V^?1 s^?1), ultra‐high hole mobilities (up to 12.25 cm² V^?1 s^?1) with an on/off ratio (I_on/I_off) of at least 10⁶ are achieved in the FETs fabricated using the polymers. The developed polymers exhibit extraordinarily high electrical performance with both hole and electron mobilities superior to that of unipolar amorphous silicon.     

Effect of Alkyl Chain Branching Point on 3D Crystallinity in High N‐Type Mobility Indolonaphthyridine Polymers

Herein, this study investigates the impact of branching‐point‐extended alkyl chains on the charge transport properties of three ultrahigh n‐type mobility conjugated polymers. Using grazing incidence wide‐angle X‐ray scattering, analysis of the crystallinity of the series shows that while π–π interactions are increased for all three polymers as expected, the impact of the side‐chain engineering on polymer backbone crystallinity is unique to each polymer and correlates to the observed changes in charge transport. With the three polymers exhibiting n‐type mobilities between 0.63 and 1.04 cm² V^?1 s^?1, these results ratify that the indolonaphthyridine building block has an unprecedented intrinsic ability to furnish high‐performance n‐type organic semiconductors.     

Inkjet Printed Large‐Area Flexible Few‐Layer Graphene Thermoelectrics

Graphene‐based organic nanocomposites have ascended as promising candidates for thermoelectric energy conversion. In order to adopt existing scalable printing methods for developing thermostable graphene‐based thermoelectric devices, optimization of both the material ink and the thermoelectric properties of the resulting films are required. Here, inkjet‐printed large‐area flexible graphene thin films with outstanding thermoelectric properties are reported. The thermal and electronic transport properties of the films reveal the so‐called phonon‐glass electron‐crystal character (i.e., electrical transport behavior akin to that of few‐layer graphene flakes with quenched thermal transport arising from the disordered nanoporous structure). As a result, the all‐graphene films show a room‐temperature thermoelectric power factor of 18.7 µW m^?1 K^?2, representing over a threefold improvement to previous solution‐processed all‐graphene structures. The demonstration of inkjet‐printed thermoelectric devices underscores the potential for future flexible, scalable, and low‐cost thermoelectric applications, such as harvesting energy from body heat in wearable applications.     

Side Chain Optimization of Naphthalenediimide–Bithiophene‐Based Polymers to Enhance the Electron Mobility and the Performance in All‐Polymer Solar Cells

Tuning the side chains of conjugated polymers is a simple, yet effective strategy for modulating their structural and electrical properties, but their impact on n‐type conjugated polymers has not been studied extensively, particularly in the area of all‐polymer solar cells (all‐PSCs). Herein, the effects of side chain engineering of P(NDI2OD‐T2) polymer (also known as Polyera Activink N2200) are investigated, which is the most widely used n‐type polymer in all‐PSCs and organic field‐effect transistors (OFETs), on their structural and electronic properties. A series of naphthalenediimide‐bithiophene‐based copolymers (P(NDIR‐T2)) is synthesized, with different side chains (R) of 2‐hexyldecyl (2‐HD), 2‐octyldodecyl (2‐OD), and 2‐decyltetradecyl (2‐DT). The P(NDI2HD‐T2) exhibits more noticeable crystalline behaviors than P(NDI2OD‐T2) and P(NDI2DT‐T2), thereby facilitating superior 3D charge transport. For example, the P(NDI2HD‐T2) shows the highest OFET electron mobility (1.90 cm² V^?1 s^?1). Also, a series of all‐PSCs is produced using different electron donors of PTB7‐Th, PTB7, and PPDT2FBT. The P(NDI2HD‐T2) based all‐PSCs produce much higher power conversion efficiency (PCE) irrespective of the electron donors. In particular, the PTB7‐Th:P(NDI2HD‐T2) forms highly ordered, strong face‐on interchain stackings, and has better intermixed bulk‐heterojunction morphology, producing the highest PCE of 6.11% that has been obtained by P(NDIR‐T2) based all‐PSCs to date.     

Self‐Assembled,Millimeter‐Sized TIPS‐Pentacene Spherulites Grown on Partially Crosslinked Polymer Gate Dielectric

Here, a highly crystalline and self‐assembled 6,13‐bis(triisopropylsilylethynyl) pentacene (TIPS‐Pentacene) thin films formed by simple spin‐coating for the fabrication of high‐performance solution‐processed organic field‐effect transistors (OFETs) are reported. Rather than using semiconducting organic small‐molecule–insulating polymer blends for an active layer of an organic transistor, TIPS‐Pentacene organic semiconductor is separately self‐assembled on partially crosslinked poly‐4‐vinylphenol:poly(melamine‐co‐formaldehyde) (PVP:PMF) gate dielectric, which results in a vertically segregated semiconductor‐dielectric film with millimeter‐sized spherulite‐crystalline morphology of TIPS‐Pentacene. The structural and electrical properties of TIPS‐Pentacene/PVP:PMF films have been studied using a combination of polarized optical microscopy, atomic force microscopy, 2D‐grazing incidence wide‐angle X‐ray scattering, and secondary ion mass spectrometry. It is finally demonstrated a high‐performance OFETs with a maximum hole mobility of 3.40 cm² V^?1 s^?1 which is, to the best of our knowledge, one of the highest mobility values for TIPS‐Pentacene OFETs fabricated using a conventional solution process. It is expected that this new deposition method would be applicable to other small molecular semiconductor–curable polymer gate dielectric systems for high‐performance organic electronic applications.     

Dual Electrostatic Assembly of Graphene Encapsulated Nanosheet‐Assembled ZnO‐Mn‐C Hollow Microspheres as a Lithium Ion Battery Anode

Graphene encapsulated nanosheet‐assembled ZnO‐Mn‐C hierarchical hollow microspheres are produced through a simple yet effective dual electrostatic assembly strategy, followed by a heating treatment in inert atmosphere. The modification of graphene sheets, metal Mn, and in situ carbon leads to form 3D interconnected conductive framework as electron highways. The hollow structure and the open configuration of hierarchical microspheres guarantee good structural stability and rapid ionic transport. More importantly, according to the density functional theory calculations, the oxygen vacancies in the hierarchical microspheres would cause an imbalanced charge distribution and thus the formation of local in‐plane electric fields around oxygen vacancy sites, which is beneficial for the ionic/electronic transport during cycling. Due to this multiscale coordinated design, the as‐fabricated graphene encapsulated nanosheet‐assembled ZnO‐Mn‐C hierarchical hollow microspheres demonstrate good lithium storage properties in terms of high reversible capacity (1094 mA h g^?1 at 100 mA g^?1), outstanding high‐rate long‐term cycling stability (843 mA h g^?1 after 1000 cycles at 2000 mA g^?1), and remarkable rate capability (422 mA h g^?1 after total 1600 cycles at 5000 mA g^?1).     

High‐Performance All‐Polymer Photoresponse Devices Based on Acceptor–Acceptor Conjugated Polymers

Three acceptor–acceptor (A–A) type conjugated polymers based on isoindigo and naphthalene diimide/perylene diimide are designed and synthesized to study the effects of building blocks and alkyl chains on the polymer properties and performance of all‐polymer photoresponse devices. Variation of the building blocks and alkyl chains can influence the thermal, optical, and electrochemical properties of the polymers, as indicated by thermogravimetric analysis, differential scanning calorimetry, UV–vis, cyclic voltammetry, and density functional theory calculations. Based on the A–A type conjugated polymers, the most efficient all‐polymer photovoltaic cells are achieved with an efficiency of 2.68%, and the first all‐polymer photodetectors are constructed with high responsivity (0.12 A W^?1) and detectivity (1.2 × 10¹² Jones), comparable to those of the best fullerene based organic photodetectors and inorganic photodetectors. Photoluminescence spectra, charge transport properties, and morphology of blend films are investigated to elucidate the influence of polymeric structures on device performances. This contribution demonstrates a strategy of systematically tuning the polymeric structures to achieve high performance all‐polymer photoresponse devices.     

High‐Mobility Naphthalene Diimide and Selenophene‐Vinylene‐Selenophene‐Based Conjugated Polymer: n‐Channel Organic Field‐Effect Transistors and Structure–Property Relationship

Interdependence of chemical structure, thin‐film morphology, and transport properties is a key, yet often elusive aspect characterizing the design and development of high‐mobility, solution‐processed polymers for large‐area and flexible electronics applications. There is a specific need to achieve >1 cm² V^?1 s^?1 field‐effect mobilities (μ) at low processing temperatures in combination with environmental stability, especially in the case of electron‐transporting polymers, which are still lagging behind hole transporting materials. Here, the synthesis of a naphthalene‐diimide based donor–acceptor copolymer characterized by a selenophene vinylene selenophene donor moiety is reported. Optimized field‐effect transistors show maximum μ of 2.4 cm² V^?1 s^?1 and promising ambient stability. A very marked film structural evolution is revealed with increasing annealing temperature, with evidence of a remarkable 3D crystallinity above 180 °C. Conversely, transport properties are found to be substantially optimized at 150 °C, with limited gain at higher temperature. This discrepancy is rationalized by the presence of a surface‐segregated prevalently edge‐on packed polymer phase, dominating the device accumulated channel. This study therefore serves the purpose of presenting a promising, high‐electron‐mobility copolymer that is processable at relatively low temperatures, and of clearly highlighting the necessity of specifically investigating channel morphology in assessing the structure–property nexus in semiconducting polymer thin films.     

Donor–Acceptor‐Conjugated Polymer for High‐Performance Organic Field‐Effect Transistors: A Progress Report

Polymeric semiconductors have demonstrated great potential in the mass production of low‐cost, lightweight, flexible, and stretchable electronic devices, making them very attractive for commercial applications. Over the past three decades, remarkable progress has been made in donor–acceptor (D–A) polymer‐based field‐effect transistors, with their charge‐carrier mobility exceeding 10 cm² V^?1 s^?1. Numerous molecular designs of D–A polymers have emerged and evolved along with progress in understanding the charge transport physics behind their high mobility. In this review, the current understanding of charge transport in polymeric semiconductors is covered along with significant features observed in high‐mobility D–A polymers, with a particular focus on polymeric microstructures. Subsequently, emerging molecular designs with further prospective improvements in charge‐carrier mobility are described. Moreover, the current issues and outlook for future generations of polymeric semiconductors are discussed.     

Kinetically Controlled Crystallization in Conjugated Polymer Films for High‐Performance Organic Field‐Effect Transistors

Ordering of semiconducting polymers in thin films from the nano to microscale is strongly correlated with charge transport properties as well as organic field‐effect transistor performance. This paper reports a method to control nano to microscale ordering of poly{[N,N′‐bis(2‐octyldodecyl)‐naphthalene‐1,4,5,8‐bis(dicarboximide)‐2,6‐diyl]‐alt‐5,5′‐(2,2′‐bithiophene)} (P(NDI2OD‐T2)) thin films by precisely regulating the solidification rate from the metastable state just before crystallization. The proposed simple but effective approach, kinetically controlled crystallization, achieves optimized P(NDI2OD‐T2) films with large polymer domains, long range ordered fibrillar structures, and molecular orientation preferable for electron transport leading to dramatic morphological changes in both polymer domain sizes at the micrometer scale and molecular packing structures at nanoscales. Structural changes significantly increase electron mobilities up to 3.43 ± 0.39 cm² V^?1 s^?1 with high reliability, almost two orders of enhancement compared with devices from naturally dried films. Small contact resistance is also obtained for electron injection (0.13 MΩ cm), low activation energy (62.51 meV), and narrow density of states distribution for electron transport in optimized thin films. It is believed that this study offers important insight into the crystallization of conjugated polymers that can be broadly applied to optimize the morphology of semiconducting polymer films for solution processed organic electronic devices.     

Open‐Shell Donor–Acceptor Conjugated Polymers with High Electrical Conductivity

Conductive polymers largely derive their electronic functionality from chemical doping, processes by which redox and charge‐transfer reactions form mobile carriers. While decades of research have demonstrated fundamentally new technologies that merge the unique functionality of these materials with the chemical versatility of macromolecules, doping and the resultant material properties are not ideal for many applications. Here, it is demonstrated that open‐shell conjugated polymers comprised of alternating cyclopentadithiophene and thiadiazoloquinoxaline units can achieve high electrical conductivities in their native “undoped” form. Spectroscopic, electrochemical, electron paramagnetic resonance, and magnetic susceptibility measurements demonstrate that this donor–acceptor architecture promotes very narrow bandgaps, strong electronic correlations, high‐spin ground states, and long‐range π‐delocalization. A comparative study of structural variants and processing methodologies demonstrates that the conductivity can be tuned up to 8.18 S cm^?1. This exceeds other neutral narrow bandgap conjugated polymers, many doped polymers, radical conductors, and is comparable to commercial grades of poly(styrene‐sulfonate)‐doped poly(3,4‐ethylenedioxythiophene). X‐ray and morphological studies trace the high conductivity to rigid backbone conformations emanating from strong π‐interactions and long‐range ordered structures formed through self‐organization that lead to a network of delocalized open‐shell sites in electronic communication. The results offer a new platform for the transport of charge in molecular systems.     

Single Crystal Microwires of p‐DTS(FBTTh2)2 and Their Use in the Fabrication of Field‐Effect Transistors and Photodetectors

Single crystal microwires of a well‐studied organic semiconductor used in organic solar cells, namely p‐DTS(FBTTh₂)₂, are prepared via a self‐assembly method in solution. The high level of intermolecular organization in the single crystals facilitates migration of charges, relative to solution‐processed films, and provides insight into the intrinsic charge transport properties of p‐DTS(FBTTh₂)₂. Field‐effect transistors based on the microwires can achieve hole mobilities on the order of ≈1.8 cm² V^?1 s^?1. Furthermore, these microwires show photoresponsive electrical characteristics and can act as photoswitches, with switch ratios over 1000. These experimental results are interpreted using theoretical simulations using an atomistic density functional theory approach. Based on the lattice organization, intermolecular couplings and reorganization energies are calculated, and hole mobilities for comparison with experimental measurements are further estimated. These results demonstrate a unique example of the optoelectronic applications of p‐DTS(FBTTh₂)₂ microwires.     

Liquid‐Crystalline Perylene Diester Polymers with Tunable Charge‐Carrier Mobility

New classes of liquid‐crystalline semiconductor polymers based on perylene diester benzimidazole and perylene diester imide mesogens are reported. Two highly soluble side‐chain polymers, poly(perylene diester benzimidazole acrylate) (PPDB) and poly(perylene diester imide acrylate) (PPDI) are synthesized by nitroxide‐mediated radical polymerization (NMRP). PPDB shows n‐type semiconductor performance with electron mobilities of 3.2 × 10^?4 cm² V^?1 s^?1 obtained in a diode configuration by fitting the space‐charge‐limited currents (SCLC) according to the Mott–Gurney equation. Interestingly, PPDI performs preferentially as a p‐type material with a hole mobility of 1.5 × 10^?4 cm² V^?1 s^?1, which is attributed to the less electron‐deficient perylene core of PPDI compared to PPDB. Optical properties are investigated by UV‐vis and fluorescence spectroscopy. The extended π‐conjugation system due to the benzimidazole unit of PPDB leads to a considerably broader absorption in the visible region compared to PPDI. HOMO and LUMO levels of the polymers are also determined by cyclic voltammetry; the resulting energy band‐gaps are 1.86 eV for PPDB and 2.16 eV for PPDI. Thermal behavior and liquid crystallinity are studied by differential scanning calorimetry, polarized optical microscopy, and X‐ray diffraction measurements. The results indicate liquid‐crystalline order of the polymers over a broad temperature range. These thermal, electrical, and optical properties make the perylene side‐chain polymers attractive materials for organic photovoltaics.     

Effect of Donor Molecular Structure and Gate Dielectric on Charge‐Transporting Characteristics for Isoindigo‐Based Donor–Acceptor Conjugated Polymers

This study investigates the effect of the molecular structure of three different donor units, naphthalene (Np), bithiophene (BT), and thiophene–vinylene–thiophene (TVT), in isoindigo (IIG)‐based donor –acceptor conjugated polymers (PIIG‐Np, PIIG‐BT and PIIG‐TVT) on the charge carrier mobility of organic field‐effect transistors (OFETs). The charge transport properties of three different IIG‐based polymers strongly depend on donor units. PIIG–BT OFETs showed 50 times higher hole mobility (0.63 cm² V^?1 s^?1) than PIIG–TVT and PIIG–Np ones of ≈ 0.01 cm² V^?1 s^?1 with CYTOP dielectric though the BT units have less planarity than the TVT and Np units. The reasons for the different mobility in IIG‐based polymers are studied by analyzing the energy structure by absorption spectra, calculating transport levels by density functional theory, investigating the in‐ and out‐of‐plane crystallinity of thin film by grazing‐incidence wide‐angle X‐ray scattering, and extracting key transport parameters via low‐temperature measurements. By combining theoretical, optical, electrical, and structural analyses, this study finds that the large difference in OFET mobility mainly originates from the transport disorders determined by the different microcrystal structure, rather than the intrinsic transport properties in isolated chains for different polymers.     

Effect of Non‐Chlorinated Mixed Solvents on Charge Transport and Morphology of Solution‐Processed Polymer Field‐Effect Transistors

Using non‐chlorinated solvents for polymer device fabrication is highly desirable to avoid the negative environmental and health effects of chlorinated solvents. Here, a non‐chlorinated mixed solvent system, composed by a mixture of tetrahydronaphthalene and p­‐xylene, is described for processing a high mobility donor‐acceptor fused thiophene‐diketopyrrolopyrrole copolymer (PTDPPTFT4) in thin film transistors. The effects of the use of a mixed solvent system on the device performance, e.g., charge transport, morphology, and molecular packing, are investigated. p‐Xylene is chosen to promote polymer aggregation in solution, while a higher boiling point solvent, tetrahydronaphthalene, is used to allow a longer evaporation time and better solubility, which further facilitates morphological tuning. By optimizing the ratio of the two solvents, the charge transport characteristics of the polymer semiconductor device are observed to significantly improve for polymer devices deposited by spin coating and solution shearing. Average charge carrier mobilities of 3.13 cm² V^?1 s^?1 and a maximum value as high as 3.94 cm² V^?1 s^?1 are obtained by solution shearing. The combination of non‐chlorinated mixed solvents and the solution shearing film deposition provide a practical and environmentally‐friendly approach to achieve high performance polymer transistor devices.     

Effect of Alkyl Side‐Chain Length on Photovoltaic Properties of Poly(3‐alkylthiophene)/PCBM Bulk Heterojunctions

The morphological, bipolar charge‐carrier transport, and photovoltaic characteristics of poly(3‐alkylthiophene) (P3AT):[6,6]‐phenyl‐C61‐butyric acid methyl ester (PCBM) blends are studied as a function of alkyl side‐chain length m, where m equals the number of alkyl carbon atoms. The P3ATs studied are poly(3‐butylthiophene) (P3BT, m = 4), poly(3‐pentylthiophene) (P3PT, m = 5), and poly(3‐hexylthiophene) (P3HT, m = 6). Solar cells with these blends deliver similar order of photo‐current yield (exceeding 10 mA cm^?2) irrespective of side‐chain length. Power conversion efficiencies of 3.2, 4.3, and 4.6% are within reach using solar cells with active layers of P3BT:PCBM (1:0.8), P3PT:PCBM (1:1), and P3HT:PCBM (1:1), respectively. A difference in fill factor values is found to be the main source of efficiency difference. Morphological studies reveal an increase in the degree of phase separation with increasing alkyl chain length. Moreover, while P3PT:PCBM and P3HT:PCBM films have similar hole mobility, measured by hole‐only diodes, the hole mobility in P3BT:PCBM lowers by nearly a factor of four. Bipolar measurements made by field‐effect transistor showed a decrease in the hole mobility and an increase in the electron mobility with increasing alkyl chain length. Balanced charge transport is only achieved in the P3HT:PCBM blend. This, together with better processing properties, explains the superior properties of P3HT as a solar cell material. P3PT is proved to be a potentially competitive material. The optoelectronic and charge transport properties observed in the different P3AT:PCBM bulk heterojunction (BHJ) blends provide useful information for understanding the physics of BHJ films and the working principles of the corresponding solar cells.     

Impact of Polystyrene Oligomer Side Chains on Naphthalene Diimide–Bithiophene Polymers as n‐Type Semiconductors for Organic Field‐Effect Transistors

A series of naphthalene diimide‐based conjugated polymers are prepared with various molar percentage of low molecular weight polystyrene (PS) oligomer of narrow polydispersity as the side chain. The PS side chains are incorporated through preparation of a macromonomer by chain termination of living anionic polymerization. The effects of the PS side chains amount (0–20 mol%) versus overall sidechain on the electrical properties of the resulting polymers as n‐type polymer semiconductors in field‐effect transistors are investigated. We observe that all the studied polymers show similarly high electron mobility (≈0.2 cm² V^?1 s^?1). Importantly, the polymers with high PS side chain content (20 mol%) show a significantly improved device stability under ambient conditions, when compared to the polymers at lower PS content (0–10 mol%). By comparing this observation to the physical blending of the conjugated polymer with PS, we attribute the improved stability to the covalently attached PS side chains potentially serving as a molecular encapsulating layer around the conjugated polymer backbone, rendering it less susceptible to electron traps such as oxygen and water molecules.