Effect of SiC, Si3N4 and TiB2 additions on the oxidation resistance of TiAl alloys

The oxidation behavior of TiAl alloys containing dispersed particles of (5, 10, 15 wt.%) SiC, (3,5 wt.%) Si₃N₄ or (3, 5, 10 wt.%) TiB₂ was studied between 800 and 1200°C in atmospheric air. The TiAl−(SiC, Si₃N₄) alloys oxidized to TiO₂, Al₂O₃, and SiO₂. The TiAl−TiB₂ alloys oxidized to TiO₂, Al₂O₃, and B₂O₃ which evaporated during oxidation. Improvement in oxidation resistance accompanied by thin, dense scale formation due to the addition of dispersoids originated primarily from the enhanced alumina-forming tendency, improved scale adhesion by oxide grain refinement owing to the beneficial effect of dispersoids, and the incorporation of SiO₂ within the oxide scale in the case of TiAl−(SiC, Si₃N₄) alloys.     

The Oxidation of TiB2 Particle-Reinforced TiAl Intermetallic Composites

The oxidation kinetics of TiAl alloys with and without (3, 5, 10 wt.%) TiB₂ dispersoids were studied between 1073 and 1273 K in atmospheric air. The inert TiB₂ dispersoids effectively increased the oxidation resistance of TiAl alloys. The higher the TiB₂ dispersoids content, the more pronounced the effect. The oxide scale formed on TiAl–TiB₂ composites was triple-layered, consisting mainly of an outer TiO₂ layer, an intermediate Al₂O₃ layer, and an inner (TiO₂+Al₂O₃) mixed layer. No B₂O₃ was observed within the oxide scale because of its high vapor pressure. A thin Ti₃Al sublayer and discrete TiN particles were found at the oxide–substrate interface. During the oxidation of TiAl alloys with and without TiB₂ dispersoids, titanium ions diffused outwardly to form the outer TiO₂ layer, while oxygen ions transported inwardly to form the inner (TiO₂+Al₂O₃) mixed layer. The increased oxidation resistance by the addition of TiB₂ was attributed to the enhanced alumina-forming tendency and thin and dense scale formation.     

Cyclic oxidation behavior of TiAl composites incorporated with TiB2 dispersoids

TiAl alloys incorporated in (0,3,5,10) wt.% TiB₂ dispersoids were manufactured via mechanical alloyingspark plasma sintering (MA-SPS), and their cyclic oxidation characteristics were studied at 800, 900 and 1000°C in air. The cyclic oxidation resistance of the prepared TiAl-TiB₂ composites effectively increased with increases in TiB₂ content. The oxide scale formed consisted of an outer TiO₂ layer, an intermediate Al₂O₃ layer, and an inner (Al₂O₃+TiO₂) mixed layer. The scale adherence was relatively good, and much thinner oxide scales, when compared to TiB₂-free TiAl alloys, were formed on the prepared composites. The incorporated TiB₂ dispersoids oxidized to TiO₂ and B₂O₃ which evaporated during oxidation.     

The oxidation of cobalt based alloys containing partially dissolved particles of Si3N4 at 1000°C

The isothermal oxidation behavior of Co-Cr and Co-Cr-Si alloys with and without 5, 10, and 15 vol.% dispersions of unstable Si₃N₄ particles was studied in 1 atm of oxygen at 1000°C. The dispersion of Si₃N₄ which dissolved partially in the matrix, greatly reduced the oxidation rate of Co-Cr alloys. Silicon nitride was found to promote the formation of continuous Cr₂O₃ layers at low chromium concentrations. Furthermore, the unstable Si₃N₄ was more effective in reducing the oxidation rate than an alloy containing an equivalent amount of silicon. Additions of 15vol.% Si₃N₄ tended to increase the oxidation rate by forming nonprotective SiO₂ particles which disrupted the protective Cr₂O₃ scale. The mechanism of oxidation was altered due to the Si₃N₄ additions. Marker experiments indicated oxygen diffusion inward via the CoO lattice, rather than a combination of both oxygen and metal ion motion which is encountered in Co-Cr alloys.     

The effect of an Al2O3 dispersion on the adhesion of Al2O3 scales on aluminized Co-10% Cr alloys

The beneficial effect of dispersions of reactive-metal oxide particles on the adhesion of Cr₂O₃ and Al₂O₃ scales formed on heat-resisting alloys is wellknown. It has been shown that an Al₂O₃ dispersion in an alloy can improve the adhesion of a Cr₂O₃ scale, and it is of particular interest in assessing the various theoretical proposals for the effect to determine whether such a dispersion can affect the adhesion of an Al₂O₃ scale. In this investigation, a Co–10% Cr–1 % Al alloy was first internally oxidized to form an Al₂O₃ dispersion. This alloy was then aluminized so that on subsequent oxidation an Al₂O₃ scale developed. It was shown that the dispersion did indeed improve the scale adhesion. The implications of this result are discussed.     

Effect of Al on high-temperature corrosion of Co-15a/oNb alloys in H2-H2O-H2S environments

Co–15 at.% Nb alloys containing up to 15 at.% Al were corroded in gaseous H₂–H₂O–H₂S mixtures over the temperature range of 600–900°C. The corrosion kinetics followed the parabolic rate law at all temperatures. Corrosion resistance improved with increasing Al content except at 900°C. Duplex scales formed on alloys consisting of an outer layer of cobalt sulfide and a heterophasic inner layer. A small amount of Al₂O₃ was found only on Co–15Nb–15Al. Contrary to what formed in Co–Nb binary alloys, neither NbS₂ nor NbO₂ were found in the inner layer of all alloys, but Nb₃S₄ did form. The absence of NbS₂ and NbO₂ is due to the formation of stable Al₂O₃ and Al₂S₃ that effectively blocked the inward diffusion of oxygen and sulfur, respectively, and to the reduction of activity of Nb by Al additions in the alloys. Intercalation of ions in the empty hexagonal channels of Nb₃S₄ is associated with the blockage of the transport of cobalt. An unknown phase (possibly Al_0.5NbS₂) was detected. Alloys corroded at 900°C were abnormally fast and formed a scale containing CoNb₃S₆ and Co. Pt markers were found at the interface between the inner and outer layers.     

The effect of Al on the corrosion behavior of Ni-Mo in a H2/H2O/H2S gas mixture

The corrosion behavior of seven Ni-Mo-Al alloys was investigated over the temperature range of 600–950°C in a mixed-gas atmosphere of H ₂/H ₂O/H ₂ S. The parabolic law was followed at low temperatures, while linear kinetics were generally observed at higher temperatures. At a fixed Mo content, the transition from parabolic to linear kinetics shifted to higher temperature with increasing Al concentration. Double-layered scales generally formed on alloys having a low Al content, consisting of an outer layer of nickel sulfide and a complex inner scale. The thickness of the outer scale and the inner scale decreased as the Al content increased. The outer scale became porous and discontinuous with increasing Al content and temperature. Al ₂ O ₃ was detected in the scales of all alloys corroded at higher temperatures ( 800°C), even though the amount of Al ₂ O ₃ was very small in some cases. The decrease in corrosion rate with increasing Al content may be attributed to the formation of Al ₂ O ₃,Al _0.55 Mo ₂ S ₄,and Al ₂ S ₃ in the inner scale.     

The corrosion behavior of Ni-Al alloys and Ni-Nb-Al alloys in a H2/H2O/H2S gas mixture

The corrosion behavior of two Ni-Al alloys and four Ni-Nb-Al alloys was studied over the temperature range of 600° C to 1000° C in a mixed-gas of H₂/H₂O/H₂S. The parabolic law was generally followed, although linear kinetics were also observed. Multiple-stage kinetics were observed for the Ni-Al alloys. Generally, the scales formed on Ni-13.5Al and Ni-Nb-Al alloys were multilayered, with an outer layer of nickel sulfide with or without pure Ni particles and a complex inner scale. The outer scale became porous and discontinuous with increasing temperature. Very thin scales formed on Ni-31Al. The reduction in corrosion rate with increasing Al content is ascribed to the formation of Al₂O₃ and Al₂S₃ in the scale. Platinum markers were found at the interface between the outer and inner scales.     

The corrosion behavior of Ni-Nb alloys in a mixed gas of H2-H2O-H2S

The corrosion behavior of Ni-Nb alloys containing up to 40 wt.% Nb was studied over the temperature range of 550–800°C in a mixed H₂/H₂O/H₂S gas. The scales formed on all alloys were multilayered. The outer scale was single-phase Ni₃S₂, while the structure and constitution of the inner scale depended on alloy composition and reaction conditions. Internal oxidation has been found in Ni-20Nb and Ni-30Nb, external oxidation has been observed on Ni-34Nb. Platinum markers were located at the interface between the outer scale and inner scale. The decrease in corrosion rate with increasing Nb content may be attributed to the presence of increasing amounts of Ni-Nb double sulfides as well as to the presence of Nb₂O₅ in the inner region of the scale.     

The high-temperature corrosion behavior of Fe-Mo-Al alloys in H2/H2O/H2S mixed-gas environments

The corrosion behavior of 11 Fe-Mo-Al ternary alloys was studied over the temperature range 700–980°C in H₂/H₂O/H₂S mixed-gas environments. With the exception of Fe-10Mo-7Al, for which breakaway kinetics were observed at higher temperatures, all alloys followed the parabolic rate law, despite two-stage kinetics which were observed in some cases. A kinetics inversion was observed for alloys containing 7 wt.% Al between 700–800°C. The corrosion rates of Fe-20Mo and Fe-30Mo were found to be reduced by five orders of magnitude at all temperatures by the addition of 9.1 or higher wt.% aluminum. The scales formed on low-Al alloys (5 wt.% Al) were duplex, consisting of an outer layer of iron sulfide (with some dissolved Al) and a complex inner of Al_0.55Mo₂S₄, FeMo₂S₄, Fe_1.25Mo₆S_7.7, FeS, and uncorroded FeAl and Fe₃Mo₂. Platinum markers were always located at the interface between the inner and outer scales for the low-Al alloys, indicating that outer-scale growth was due mainly to outward diffusion of cations (Fe and Al), while the inner scale was formed primarily by the inward flux of sulfur anions. Alloys having intermediate Al contents (7 wt.%) formed scales that consisted of FeS and Al₂O₃. The amount of Al₂O₃ increased with increasing reaction temperature. The high-Al-content alloys (9.1 and 10 wt.%) formed only Al₂O₃ which was responsible for the reduction of the corrosion rates.     

High temperature oxidation of Ti−48%Al−2%W intermetallics

Powder metallurgically produced Ti-48% Al-2%W alloys were oxidized between 800 and 1050°C in air. The W-addition was quite effective in providing isothermal and cyclic oxidation resistance. The alloys oxidized parabolically up to 1050°C during isothermal oxidation, with small weight gains. The scales were adherent up to 900°C during cyclic oxidation. Oxide scales consisted primarily of an outer TiO₂ layer, an intermediate Al₂O₃ layer, and an inner (TiO₂+Al₂O₃) mixed layer. Tungsten was present below the intermediate Al₂O₃ layer. and also at the scale-matrix interface as W-enriched compounds. Below the oxide scale, a Ti₃Al zone containing some W and O existed.     

Effect of Ion Plating TiN on the Oxidation of Sputtered NiCrAlY-Coated Ti3Al-Nb in Air at 850-950°C

A single sputtered NiCrAlY coating and a complexcoating of inner ion-plated TiN and outer sputteredNiCrAlY were prepared on the intermetallic compoundTi₃Al-Nb. Their oxidation behavior wasexamined at 850, 900, and 950°C in air by thermalgravimetry combined with XRD, SEM, and EDAX. The resultsshowed that Ti₃Al-Nb followed approximatelyparabolic oxi dation, forming an outer thinAl₂O₃-rich scale and an inner TiO₂-rich layer doped withNb at the three temperatures. The TiO₂-richlayer doped with Nb dominated the oxidation reaction.The single NiCrAlY coating did not follow parabolicoxidation exactly at 850 and 950°C, but oxidizedapproximately in a parabolic manner, because theinstantaneous parabolic constants changed slightly withtime. Besides the Al₂O₃ scale,TiO₂ formed from the coating surface at the coating-substrate interface. Thedeterioration of the coating accelerated with increasingtemperature. The NiCrAlY-TiN coating showed two-stageparabolic oxidation at 850 and 900°C, and anapproximate parabolic oxidation at 950°C. The TiN layerwas effective as a barrier to inhibit coating-alloyinterdiffusion.     

Effects of Cr and Nb on the high temperature oxidation of TiAl

From isothermal and cyclic oxidation tests on thermomechanically treated Ti-51%Al, Ti-47%Al-4%Cr, and Ti-48%Al-2%Cr-2%Nb alloys at 800, 900, 1000°C in air, it was found that Ti-48%Al-2%Cr-2%Nb and Ti-47%Al-4%Cr had the best and the worst oxidation resistance, respectively. The oxide scales consisted primarily of TiO₂ and Al₂O₃, with and without a small amount of dissolved Cr and Nb ions, depending on the alloy composition. These ions were slightly enriched inside the inner oxide layer, and strongly enriched around the scale-matrix interface. The outer TiO₂-rich layer was formed by the outward diffusion of Ti ions, while the inner (TiO₂+Al₂O₃) mixed layer was formed by the inward transport of oxygen. The outward movement of Al ions formed the intermediated Al₂O₃-rich layer, above the prepared alloys.     

Oxidation behavior of Ti3AlC2 at 1000-1400 °C in air

The isothermal oxidation behavior of bulk Ti₃AlC₂ has been investigated at 1000-1400 °C in air for exposure times up to 20 h by means of TGA, XRD, SEM and EDS. It has been demonstrated that Ti₃AlC₂ has excellent oxidation resistance. The oxidation of Ti₃AlC₂ generally followed a parabolic rate law with parabolic rate constants, k_p that increased from 4.1×10⁻¹¹ to 1.7×10⁻⁸ kg² m⁻⁴ s⁻¹ as the temperature increased from 1000 to 1400 °C. The scales formed at temperatures below 1300 °C were dense, adherent, resistant to cyclic oxidation and layered. The inner layer of these scales formed at temperatures below 1300 °C was continuous α-Al₂O₃. The outer layer changed from rutile TiO₂ at temperatures below 1200 °C to a mixture of Al₂TiO₅ and TiO₂ at 1300 °C. In the samples oxidized at 1400 °C, the scale consisted of a mixture of Al₂TiO₅ and, predominantly, α-Al₂O₃, while the adhesion of the scales to the substrates was less than that at the lower temperatures. Effect of carbon monoxide at scale/substrate was involved in the formation of the continuous Al₂O₃ layers.     

Effect of Fe on the high temperature oxidation of TiAl alloys

An alloy of 51.23Ti−48.73Al−0.4Fe (at.%) was oxidized at 800, 900 and 1000°C in air to determine the effect of Fe on oxidation. The scales formed consisted of an outer TiO₂ layer, an intermediate Al₂O₃ layer, and an inner mixed (TiO₂ Al₂O₃) layer, typical of conventional TiAl alloys. A small amount of dissolved Fe ions was weakly segregated in the outer TiO₂ layer and also in the inner (TiO₂−Al₂O₃) mixed layer. Ti₂AIN and TiN were detected in the scale in some instances. A thin, oxygen-affected Ti₃Al sublayer formed at the oxide-substrate interface. The overall oxidation kinetics and the scale morphology were not affected by Fe-addition.     

The corrosion behavior of Fe-Nb-Al alloys in H2/H2O/H2S atmospheres

The corrosion behavior of eight Fe-Nb-Al ternary alloys was studied over the temperature range 700–980°C in H₂/H₂O/H₂S atmospheres. The corrosion kinetics followed the parabolic rate law for all alloys at all temperatures. The corrosion rates were reduced with increasing Nb content for Fe-x Nb -3Al alloys, the most pronounced reduction occurred as the Nb content increased from 30 to 40 wt.%. The corrosion rate of Fe-30Nb decreased by six orders of magnitude at 700°C and by five orders of magnitude at 800°C or above by the addition of 10 wt.% aluminum. The scales formed on low-Al alloys (3 wt.% Al) were duplex, consisting of an outer layer of iron sulfide (with Al dissolved near the outer-/inner-layer interface) and an inner complex layer of Fe_xNb₂S₄(FeNb₂S₄ or FeNb₃S₆), FeS, Nb₃S₄ (only detected for Nb contents of 30 wt.% or higher) and uncorroded Fe₂Nb. No oxides were detected on the low-Al alloys after corrosion at any temperature. Platinum markers were found to be located at the interface between the inner and outer scales for the low-Al alloys, suggesting that the outer scale grew by the outward transport of cations (Fe and Al) and the inner scale grew by the inward transport of sulfur. The scales formed on high-Al alloys (5 wt.% Al) were complex, consisting primarily of Nb₃S₄, Al₂O₃ and (Fe, Al)_xNb₂S₄, and minor amounts of (Fe, Al)S and uncorroded intermetallics (FeAl and Fe₂Nb). The formation of Nb₃S₄ and Al₂O₃ blocked the transport of iron through the inner scale, resulting in the significant reduction of the corrosion rates.     

High-temperature corrosion of Co-15Mo alloys containing ternary additions of Al in mixed-gas environments

The corrosion behavior of Co-15 at.% Mo alloys containing up to 20at.% Al in gaseous H ₂ -H ₂ O-H ₂ S mixtures was studied over the temperature range of 600–900°C. The corrosion kinetics of all alloys followed the parabolic rate law over the temperature range of interest. Corrosion resistance increased with increasing aluminum content. Complex scales formed on the alloys, consisting of an outer layer of cobalt sulfide and a heterophasic inner layer. Al ₂ O ₃ formed only at high temperatures in alloys having aluminum additions of 15at.% or more. The absence of Al ₂ O ₃ in some cases is due to the small volume fraction of the intermetallic phase CoAl in the alloys and the nature of the slow growth rate of Al ₂ O ₃.Improvement in corrosion resistance is attributed to the presence of a ternary sulfide, Al _0.55 Mo ₂ S ₄,and Al ₂ O ₃ in the inner layer.     

Reactive-element effect of electrodeposited Y2O3 oxide films on the oxidation of Fe−25Cr and Fe−25Cr−10Al alloys

Thin Y₂O₃ films were deposited by the electrochemical deposition-pyrolysis process on Fe–25Cr and Fe–25Cr–10Al alloys. The influence of the films on the oxidation behavior of the alloys was studied at 850°C and 1000°C. The results showed that Y₂O₃ films remarkably decreased the oxidation rate of Cr₂O₃-forming alloys and spallation of the scales, but they did not decrease the oxidation rate of the Al₂O₃-forming alloys, although they do reduce the spallation of Al₂O₃ scales. Y₂O₃ films remarkably change the morphology of the scales on both alloys, depending on the oxidation temperatures. These results show that the reactive-element effects of Y₂O₃ films on the Cr₂O₃ formers and Al₂O₃ formers are different.     

High temperature oxidation of thermomechanically treated Ti-47 Al−2Cr−2Nb

Thermomechanically treated Ti−47Al−2Cr−2Nb alloys were oxidized at 800°C, 900°C and 1000°C in air. Various heat treatments done to obtain duplex microstructure and stabilize microstructures did not affect the overall oxidation kinetics and the oxide morphology of the alloys. Alloys oxidized at similar rates formed oxide scales consisting primarily of an outer TiO₂ layer, an intermediate Al₂O₃ layer, and an inner (TiO₂+Al₂O₃) mixed layer. A small amount of dissolved Cr ion was preferentially segregated in the inner oxide layer. Niobium, however, was segregated in not only the inner, but also the outer oxide layer.     

The corrosion behavior of Fe-Al alloys in H2/H2S/H2O atmospheres at 700–900°C

The corrosion behavior of five Fe-Al binary alloys containing up to 40 at. % Al was studied over the temperature range of 700–900°C in a H₂/H₂S/H₂O mixture with varying sulfur partial pressures of 10^–7–10^–5 atm. and oxygen partial pressures of 10^–24–10^–2° atm. The corrosion kinetics followed the parabolic rate law in all cases, regardless of temperature and alloy composition. The parabolic rate constants decreased with increasing Al content. The scales formed on Fe-5 and –10 at.% Al were duplex, consisting of an outer layer of iron sulfide (FeS or Fe_1–xS) and an inner complex scale of FeAl₂S₄ and FeS. Alloys having intermediate Al contents (Fe-18 and –28 at.% Al) formed scales that consisted of mostly iron sulfide and Al₂O₃ as well as minor a amount of FeAl₂S₄. The amount of Al₂O₃ increased with increasing Al content. The Fe 40 at.% Al formed only Al₂O₃ at 700°C, while most Al₂O₃ and some FeS were detected at T800°C. The formation of Al₂O₃ was responsible for the reduction of the corrosion rates.