Effects of organic nucleating agents and zinc oxide nanoparticles on isotactic polypropylene crystallization

Organic nucleating agents and inorganic nanoparticles, as well as their hybrid composites, affect the crystallization temperature and morphology of the monoclinic α-form of isotactic polypropylene (iPP). Techniques such as differential scanning calorimetry, hot-stage optical microscopy with cross polars, wide angle X-ray diffraction, and transmission electron microscopy were employed. Nanoparticles of zinc oxide function as efficient supports for 1,3,5-benzene tricarboxylic-(N-2-methylcyclohexyl)triamine because the temperature at which the maximum rate of iPP crystallization occurs during 10 °C/min cooling from the molten state increases from 111 °C for the pure polymer to 125 °C at low concentrations of this hybrid nucleating agent. In the absence of zinc oxide, 0.06 wt% of this aliphatic triamine recrystallizes near 165 °C and increases the crystallization temperature of iPP by 7 °C, relative to the pure polymer. Fluorinated aromatic triamines, such as 1,3,5-benzene tricaboxylic-(N-4-fluorophenyl)triamine, are weak nucleating agents that reduce spherulite size in isotactic polypropylene but only increase the crystallization temperature marginally when the polymer is cooled from the molten state. Both micro- and nanoparticles of zinc oxide reduce spherulite size in isotactic polypropylene, but smaller spherulites are observed when the inorganic nanoparticles exhibit dimensions on the order of 40-150 nm relative to micron-size particles. In contrast, 0.06 wt% of the aliphatic triamine in iPP yields a distorted birefringent texture under cross polars that is not spherulitic. Non-spherulitic birefringent textures in iPP are also observed when the aliphatic triamine nucleating agent is coated onto micro- or nanoparticles of zinc oxide. This study demonstrates that the nonisothermal crystallization temperature of isotactic polypropylene increases by an additional 7 °C when an aliphatic triamine is distributed efficiently within the polymeric matrix by coating this nucleating agent onto zinc oxide nanoparticles.     

Influence of a particulate nucleating agent on the quiescent and flow-induced crystallization of isotactic polypropylene

Flow induced crystallization of commercial isotactic polypropylene (iPP) and its blends with sodium 2,2′-methylene bis-(4,6-di-tert-butylphenyl) phosphate (also known as NA11) is studied by means of in-situ time resolved small-angle X-ray scattering (SAXS). The isothermal crystallization at 145 °C (i.e. well below melting temperature of polymer) is performed after the application of steady shear to probe the anisotropic structure formation. In order to separate the influence of shear rate and shear time on polymer crystallization, four different shear conditions (60 s⁻¹ for 1 s, 30 s⁻¹ for 2 s, 15 s⁻¹ for 4 s and 6 s⁻¹ for 10 s) are applied while maintaining the same imposed strain in the polymer melt. Further the effect of different concentration of nucleating agent on the crystallization kinetics of iPP is examined both under quiescent and shear flow conditions. For instance, under quiescent condition, the crystallization half-time (τ_1/2) decreases with the increasing concentration of nucleating agent in the polymer. Under shear flow conditions, our observations are as follows: In the case of neat iPP, τ_1/2 decreases significantly at higher shear rates (≥30 s⁻¹). Compared to the neat iPP, for the same concentration of NA11 in the NA11/iPP blends differences in τ_1/2 with the increase in applied shear rates are significantly smaller. In other words, the crystallization kinetics is dominated by the amount of nucleating agent in the NA11/iPP blends as opposed to shear rates in the neat iPP. The present study shows that the critical value of shear rate required for chain orientation in the molten polymer is lower in the presence of the nucleating agent compared to neat iPP. The self-nucleation process investigated with the aid of differential scanning calorimetry (DSC), indicates that the nucleating efficiency of NA11 on iPP is around 60%.     

Effect of chain disentanglement on melt crystallization behavior of isotactic polypropylene

Isotactic polypropylene (iPP) with “disentangled” chains was generated through crystallization of iPP from its mineral oil solution. TGA test assured complete removal of mineral oil from iPP precipitates. Time sweep rheological measurements showed the modulus build-up with time indicating the formation of “disentangled” chains in iPP after the sample disentanglement treatment. The “disentangled” chains could preserve for a certain time before completely re-entangled during melting. Crystallization kinetics of iPP with “disentangled” chains was studied by using polarized optical microscope. The growth rate of spherulites in “disentangled” iPP was faster than that in the entangled one.     

Polymer blends based on polyolefin elastomer and polypropylene

A new family of homogeneous polyolefin polymers that exhibit unique molecular and rheological properties designated polyolefin elastomers (POEs) are characterized by a narrow molecular weight and high degrees of comonomer distribution. Because these copolymers are often elastomeric in nature, one of the uses for these materials is as impact properties improver for brittle polymers such as polypropylene at low temperatures. In this work a study was carried out about the effectiveness of the polyethylene elastomer (POE) as an impact modifier for polypropylene in relation to the traditional modifier EPDM. In this study the flow properties of of the POE/PP and EPDM/PP blends were also evaluated. The blends were analyzed by solid-state ¹³C nuclear magnetic resonance (¹³C-NMR) spectroscopy, scanning electron microscopy (SEM), and differential scanning calorimetry (DSC). The results showed that PEE/PP and EPDM/PP blends present a similar crystalline behavior, which resulted in a similar mechanical performance of the blends, on the composition analyzed. It was also verified that the POE/PP blend presents lower torque values than the EPDM/PP blend, which indicates a better processability when POE is used as an impact modifier. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 66: 2005–2014, 1997     

Effects of high molecular weight species on shear-induced orientation and crystallization of isotactic polypropylene

In situ rheo-SAXS (small-angle X-ray scattering) and—rheo-WAXD (wide-angle X-ray diffraction) techniques were used to investigate the role of high molecular weight species on the evolution of oriented microstructure in isotactic polypropylene (iPP) melt under shear flow. The two iPP samples, designated as PP-A and PP-B, respectively, had the same number-average (M_n) but different weight-average (M_w) and Z-average (M_z) molecular weights. Molecular weight distribution (MWD) of PP-A and PP-B was such that for MW<10⁵ the MWD curves overlapped; whereas in the high MW tail region, the amount of high molecular weight species was higher in PP-B than PP-A. Both samples were subjected to an identical shear condition (rate=60 s⁻¹, duration=5 s, T=155 °C). In situ 2D SAXS and WAXD images allowed the tracking of shear-induced oriented structures in the melt. It was found that the shish structures evolved much earlier, and the degree of crystal orientation and oriented crystal fractions were higher in PP-B than PP-A. Moreover, PP-B exhibited faster crystallization kinetics than PP-A. These results, along with the predictions of double reptation models of chain motion and experimental studies of chain conformation dynamics in dilute solutions under flow, suggest the following: When a polymer melt that consists of entangled chains of different lengths is deformed, the chain segments aligned with the flow eigenvector can undergo the abrupt coil-stretch-like transition, while other segments would remain in the coiled state. Since, flow-induced orientation decays much more slowly for long chains than for short chains, oriented high molecular weight species play a prominent role in formation of the stretched sections, where shish originates. Our experimental results are strong evidence of the hypothesis that even a small increase in the concentration of high molecular weight species causes a significant increase in the the formation, stability and concentration of the flow-induced oriented microstructure.     

Role of multi-wall carbon nanotube network in composites to crystallization of isotactic polypropylene matrix

The composites (iPP/CNTs) made of isotactic polypropylene (iPP) and multi-wall carbon nanotubes (CNTs) were prepared by solution blending. To improve compatibility between CNTs and iPP and to enhance dispersion of CNTs in iPP matrix, CNTs were chemically modified by grafting alkyl chains. The chemically modified CNTs had about 6 wt% grafted alkyl chains. Rheological measurements indicated that CNTs caused gelation in iPP/CNTs due to CNT network formation and the critical gelation CNT concentration was about 7.4 wt%, which was considered to be high due to the low CNT aspect ratio in this study. Crystallization behaviors of iPP/CNTs were studied by using optical microscopy (OM) and differential scanning calorimetry (DSC). Radial growth rates of spherulites during isothermal crystallization of iPP/CNTs with CNT concentrations less than 2.0 wt% measured by using OM showed decreasing trends with increasing CNT concentration. Avrami analysis of the exothermic heat flow curves during isothermal crystallization of iPP/CNTs measured by DSC indicated that crystallization rates were accelerated when CNT concentrations were lower than the critical gelation concentration, because CNTs mainly functioned as nucleating agents for crystallization, while crystallization rates did not change obviously when CNT concentrations were higher than the critical gelation concentration, because CNT network could form and mainly functioned to provide restriction to mobility and diffusion of iPP chains to crystal growth fronts.     

Effect of nucleating agent addition on crystallization of isotactic polypropylene

The isothermal and nonisothermal crystallization kinetics of nonnucleated and nucleated isotactic polypropylene (iPP) were investigated by DSC and a polarized light microscope with a hot stage. Dibenzylidene sorbitol (DBS) was used as a nucleating agent. It was found that the crystallization rate increased with the addition of DBS. The influence of DBS on fold surface energy, σ_e, was examined by the Hoffman and Lauritzen nucleation theory. It showed that σ_e decreased with the addition of DBS, suggesting that DBS is an effective nucleating agent for iPP. Ozawa's theory was used to study the nonisothermal crystallization. It was found that the crystallization temperature for the nucleated iPP was higher than that for nonnucleated iPP. The addition of DBS reduced the Ozawa exponent, suggesting a change in spherulite morphology. The cooling crystallization function has a negative exponent on the crystallization temperature. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 69: 2089–2095, 1998     

Rheologically determined negative influence of increasing nucleating agent content on the crystallization of isotactic polypropylene

Dibenzylidene sorbitol (DBS) exists in the form of fibril and usually acts as an effective nucleating agent to facilitate crystallization of polyolefin during manufacturing. In this research, the isothermal crystallization of isotactic polypropylene (iPP) containing different amounts of DBS was followed by dynamic rheometry, and described upon a viewpoint of viscoelastic property evolution. Since the adopted temperatures within the entire sample preparation and characterization process were below the melting point of DBS, the DBS additives played a role of only solid nucleating agent, thus the possible effect of a changed miscibility between iPP and DBS on the viscoelastic properties as change of temperature could be ignored. Although saturation of nucleating iPP was observed at 0.1% DBS concentration, a negative influence with further increasing DBS content on the crystallization of iPP was determined for the first time via time sweep of G′ upon a single angular frequency and application of “inverse quenching” protocol within a wide range of angular frequency. Even more, a largely increased G′ and viscosity were observed in the melt as decreasing the temperature of iPP containing 0.1% DBS, suggesting a strong quasi-solid like behavior before iPP crystallization. A complement for well understanding the crystallization of iPP containing nucleating agent was discussed based on the formation of the DBS fibrils' network, the interfacial tension between crystalline/amorphous phase, and the consistency of crystallizing lamellae. Our study demonstrates clearly that the crystalline characteristic upon saturation of heterogeneous nucleating is difficult to be detected by traditional means, but could be followed reasonably by rheological measurements which is much sensitive to the microstructural changes.     

Rheological study of polypropylene copolymer/polyolefinic elastomer blends

Blends of polypropylene copolymer (PP‐cp) and a polyolefinic elastomer (POE) were prepared by a melt‐blending process at 210°C and 60 rpm using a counterrotating twin‐screw extruder. The POE content was varied up to 25%. The shear viscosity over a wide range of shear rate was measured. All blend compositions showed well‐defined zero shear viscosity and shear thinning behavior. The melt viscosity values were between those of the principal components in all cases. Rheology of blends shows different behavior up to concentrations of POE corresponding to the tough–brittle transition. The linear viscoelastic properties (G′, G″, η*, η′, η″) were used to check the miscibility of the two components in the melt state. All blend compositions showed a good degree of miscibility over the range of POE concentrations studied. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 665–671, 2002; DOI 10.1002/app.10376     

Morphology, reorganization and stability of mesomorphic nanocrystals in isotactic polypropylene

The morphology and thermodynamic stability of crystals of isotactic polypropylene (iPP) were analyzed as a function of the path of crystallization by atomic force microscopy (AFM) and differential scanning calorimetry (DSC). Samples were melt-crystallized at different rates of cooling using a “controlled rapid cooling technique”, and subsequently annealed at elevated temperature. Mesomorphic equi-axed domains with a size less than 20 nm were obtained by fast cooling from the melt at a rate larger about 100 K s⁻¹. These domains stabilize on heating by growing in chain direction and cross-chain direction, to reach a maximum size of about 40-50 nm at a temperature of 433 K, with the quasi-globular shape preserved. Annealing at 433 K additionally triggers formation of different types of lamellae. It is suggested that these lamellae either develop by coalescence of nodules, or by recrystallization from the melt. The transition from the disordered mesomorphic structure, evident at ambient temperature after fast crystallization, to monoclinic structure on heating at about 340 K occurs at local scale within existing crystals, and cannot be linked to complete melting of mesomorphic domains and recrystallization of the melt. The temperature of melting of initial mesomorphic domains, after reorganization at elevated temperature, is identical to the temperature of melting of rather perfect lamellae, obtained by initial slow melt-crystallization, followed by annealing. The close-to-identical temperatures of melting of these crystals of largely different shapes are confirmed by model calculations, using the Gibbs-Thomson equation. Modeling of the melting temperature reveals that nodular crystals, stabilized by annealing at high temperature, exhibit a similar fold-surface as lamellar crystals.     

Interplay between crystallization behaviors and extensional deformation of isotactic polypropylene and its blend with poly(ethylene-co-octene)

Comparison investigation of the interaction between crystallization behaviors and extensional deformation of both isotactic polypropylene (iPP) and its blend with poly(ethylene-co-octene) (iPP/PEOc) was carried out in this study. The samples of iPP and the iPP/PEOc (80/20, wt.%) blend were prepared by changing the cooling rate during nonisothermal crystallization. Tensile testing showed that with the decrease of cooling rate, the progressive destruction of ductility of the two samples was resulted from the more perfect crystallites formed in the cooling process. The influence of cooling rate on the tensile properties is more prominent for pure iPP than for the iPP/PEOc blend. The crystalline structure was proven to be partially destroyed under the extensional deformation, and such crystalline structure destruction was in close association with the deformation of the specimens. The oriented noncrystalline molecular chains could easily be reorganized into more perfect crystals in postheating runs. The original crystalline structure has been found, to some extent, to determine the extensional deformation and the final crystallization behavior.     

Synergistic gelation of solutions of isotactic polypropylene and bis-(3,4-dimethyl benzylidene) sorbitol and its use in gel-processing

We report the synergistic, rapid gelation of solutions of isotactic polypropylene (i-PP) and the nucleating agent 1,3:2,4-bis-(3,4-dimethyl benzylidene) sorbitol (DMDBS) in decalin. Cooling to room temperature of a solution comprising, for instance, 3.0 wt% of a moderately high molecular weight i-PP (M_v=1.3×10⁶ g/mol) and as little as 0.0075 wt% DMDBS (0.25 wt% based on the polymer) resulted in the fast formation of highly ductile gels. In reference experiments without DMDBS, often ‘mud-cracked’, brittle polymer films were obtained, and decaline solutions of DMDBS alone at the above concentration did not form macroscopically coherent gels. In the present work we employed this useful occurrence for gel-processing/drawing of i-PP, yielding material with Young's moduli of 35 GPa, tensile strengths of approximately 1 GPa and melting temperatures measured for constrained samples as high as 228 °C.     

成核剂对聚丙烯力学性能与结晶行为的影响

研究了两种类型的成核剂对国产共聚聚丙烯的结晶形态以及拉伸强度、冲击强度的影响。结果表明:加入TMB-5型成核剂,聚丙烯的冲击强度有一定程度改善,w(TMB-5)为0.1%时,改性聚丙烯的缺口冲击强度达到最大;TMX-2型成核剂可改善聚丙烯的拉伸性能,但抗冲击性能降低较大;TMB-5型成核剂可显著地改变聚丙烯的结晶行为,诱导聚丙烯在结晶过程中主要形成β晶;TMX-2型成核剂可诱导聚丙烯在结晶过程中主要生成α晶,与纯PP相比,α晶的形成能力增强。     

Shish-kebab-like cylindrulite structures resulted from periodical shear-induced crystallization of isotactic polypropylene

In this study, isotactic polypropylene (iPP) samples were prepared by conventional injection molding (CIM) and pressure vibration injection molding (PVIM), in which a periodical shear field was imposed on the iPP melt during the cooling solidification. The distribution of supermolecular structures of samples was investigated by Polarized Light Microscopy (PLM) and Scanning Electron Microscopy (SEM). Results show that the through-the thickness-morphology of sample prepared by CIM features a typical skin-core structure, as a result of general shear-induced crystallization. This structure can be divided into three layers, including a skin layer in which the shish-kebab structure was found, a transition region with deformed spherulite structure and a core layer with spherulitic structure. However, the morphology of the sample prepared by PVIM, as a result of periodical shear-induced crystallization, features a richer and fascinating supermolecular structure and can not be roughly divided into three layers. A region full of shish-kebab-like cylindrulite structures was found between the transition region and the core layer, which is rare to be seen in conventional injection molding. Based on their various core structures, two kinds of shish-kebab-like cylindrulites were defined: one is multi-fibril-core cylindrulite of which core is an assembly of multiple fibrils, and the other is single-fibril-core cylindrulite of which the core just contains a single fibril. Based on the investigated results, a schematic illustration is proposed to depict the through-the thickness-distribution of supermolecular structure of iPP sample prepared by PVIM. The mechanism of the formation of the two kinds of shish-kebab-like cylindrulite structures is also depicted by a schematic illustration, and it was discussed in terms of periodical shear-induced crystallization.     

Effect of different nucleating agent ratios on the crystallization and properties of MAS glass ceramics

The effects of different kinds of nucleating agents on crystallization, microstructure and performances of Magnesium Aluminosilicate (MgO-Al₂O₃-SiO₂, MAS) glass-ceramics which were fabricated by melting method in this study. Also, this paper systematically investigated the mechanism of glass stability, crystallization kinetics and element distribution of MAS glass-ceramics. Herein, we used three kinds of nucleating agents, which was TiO₂, ZrO₂ and composite nucleating agent (TiO₂/ZrO₂). The results showed after the doping of nucleating agent, the content of α-cordierite was increased, the stability and crystallization kinetics of glass was changed, the precipitated crystal phase was finer and more compact. Wherein, the sample with composite nucleating agents (TiO₂, ZrO₂) has the best performance due to the highest contents of α - cordierite, uniform distribution of elements without agglomeration in the crystal phase and the most compact structure, whose Vickers hardness and bending strength can reach 9.70 GPa and 312 MPa, respectively.     

Effects of EPDM and wollastonite on structure of isotactic polypropylene blends and composites

Polypropylene blends and composites with 5, 10, and 15 vol % of EPDM and 2, 4, and 6 vol % of untreated and treated wollastonite filler were examined by applying different techniques. Elastomeric ethylene/propylene/diene terpolymer (EPDM) component and wollastonite influenced the crystallization process of isotactic polypropylene (iPP) matrix in different ways. The nucleation of hexagonal β‐iPP, the increase of overall degree of crystallinity, and crystallite size of iPP were more strongly affected by wollastonite than the addition of EPDM was. Both ingredients also differently influenced the orientation of α‐form crystals in iPP matrix. Wollastonite increased the number of a*‐axis‐oriented α‐iPP lamellae plan parallel to the sample surface, whereas the addition of EPDM reoriented the lamellae. The orientation parameters of ternary composites exhibited intermediate values between those for binary systems because of the effects of both components. EPDM elastomer considerably affected well‐developed spherulitization of iPP, increasing the spherulite size. Contrary to EPDM, because of nucleating ability or crystal habit, wollastonite caused significantly smaller iPP spherulites. Small spherulites in ternary iPP/EPDM/wollastonite composites indicated that the wollastonite filler (even in smallest amounts) exclusively determined the morphology of ternary composites. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 91: 4072–4081, 2004     

Influence of structural organization on tensile properties in mesomorphic isotactic polypropylene

The effects of annealing on the structure and mechanical properties of mesomorphic isotactic polypropylene have been investigated using wide-angle and small-angle X-ray scattering and rheo-optics in addition to tensile tests. Young's modulus of mesomorphic phase was estimated to be 5 GPa using Takayanagi model. The α-crystallitic iPP prepared by annealing the quenched mesomorphic iPP was transparent because of the absence of spherulitic structure. It was found that the mechanical yielding of α-crystallitic iPP is dominated by the plastic flow of crystalline structural units whereas the yield process of α-spherulitic iPP quenched at 80 °C is caused by the fracture or fragmentation of crystalline structural units.     

Primary nucleation behaviour in isotactic polypropylene/ethylene-propylene random copolymer blends

Primary nucleation of spherulites in blends of isotactic polypropylene (iPP) with ethylene-propylene random copolymer (EPM) has been investigated using optical microscopy. The number of spherulites generally increases with increasing EPM content. It is shown that this increase is caused by migration of heterogeneous nuclei across interface boundaries from EPM to iPP during melt-mixing. The migration was observed in the blends with the nucleating agent initially added to EPM before blending with iPP. It is suggested that the interfacial free energy difference between nuclei and the molten components of the blend is responsible for the migration of nuclei. It is also shown that self-seeded nucleation becomes damped in the blends due to partial solubility of the components and that the degradation of the blends during melt-annealing depresses the primary nucleation.     

Rheological properties,crystallization, and morphology of compatibilized blends of isotactic polypropylene and polyamide

Blends of isotactic polypropylene (iPP) with the polyamide nylon-6 (N6), prepared by extrusion, were studied with a composition of up to 30% by weight polyamide. In the case of a 70/30 iPP/N6 blend, the influence of a compatibilizing agent based on polypropylene functionalized with maleic anhydride (PP-g-MA), with compositions of 1, 3, 5, and 10% by weight in polypropylene, was followed. The influence of the concentration of N6 and the compatibilizing agent on the rheological and thermal properties, and the morphology of the blends, was analyzed by monitoring the melt viscosity at different shear rates, differential scanning calorimetry, and polarized light microscopy. Vibrational spectroscopy was used to characterize the blends and to study the effect of the compatibilizing agent. The viscosity—composition curves for the iPP/N6 blends, in the composition and shear rate ranges analyzed, show a negative deviation from the additive rule, while the opposite trend is observed for the blends compatibilized with PP-g-MA. Important variations in the spectroscopic behavior was observed between compatibilized and noncompatibilized blends, which varied as a function of the compatibilizing agent concentration. The crystallization rates of iPP in the iPP/N6 blends, under both dynamic and isothermal conditions, are much greater than are those observed for pure iPP and are directly related to the nucleating activity of the polyamide. This effect is much smaller in the presence of the compatibilizing agent. The isothermal crystallization of the polyamide N6 in compatibilized blends is affected by the presence of iPP, reducing the crystallization rate due to the diluent effect of the polypropylene. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 65: 2665–2677, 1997     

Crystallization and morphology of reactor-made blends of isotactic polypropylene and ethylene-propylene rubber

The crystallization and morphology of reactor-made blends of isotactic polypropylene (PP) with a large content of ethylene-propylene rubber (EPR) (i.e., > 50%) were investigated. In the blends, PP was found to form spherulites during the crystallization process, with the growth rate constant under isothermal conditions. For crystallization temperatures in the range of 118–152°C, the birefringence of the spherulites varied from negative to positive by decreasing crystallization temperature, while homopolypropylene (homo-PP), the same as used in the blends as a matrix, showed negative spherulites in the whole temperature range investigated (118–152°C). Both the spherulite growth rate and the overall crystallization rate were slower for the blends than for homo-PP. The density of the crystallization nuclei was lower in the blends than in the homo-PP. It was concluded that a large amount of EPR content in the reactor-made blends of PP retards and hinders the crystallization of the matrix. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 66: 1007–1014, 1997