Synthesis of carboxylic acid functionalized nanoparticles by reversible addition-fragmentation chain transfer (RAFT) miniemulsion polymerization of styrene

In this study, an addition-fragmentation chain transfer agent bearing carboxylic acid, 4-toluic acid dithiobenzoate (TADB), was used to synthesize carboxylic acid functionalized PS nanospheres via the miniemulsion polymerization. In addition, non-functionalized RAFT agent, benzyl dithiobenzoate (BDB), was also used to compare the surface properties of the PS nanoparticles. For the TADB system, the rate of polymerization was approximately two-fold faster than the BDB system, while the molecular weights and PDI of PS remain intact.With increasing the molar ratio of [TADB]/[AIBN] from 0 to 3.0, the average particle diameter is substantially increased from 90 to 126 nm. The absolute value of zeta potential and conductivity also correspondingly increase from 49.1 mV and 3.47 mS/cm to 53.9 mV and 4.21 mS/cm, respectively. The results indicate that the surface of PS nanospheres could be functionalized by means of a carboxylic acid group on the RAFT agent and the stability of the PS miniemulsion latex could be significantly improved.     

双硫酯作为链转移剂的苯乙烯本体聚合研究

研究了二硫代苯甲酸苄基酯（BDB）、二硫代苯甲酸苯乙基酯（PEDB）及二硫代苯甲酸异丙苯基酯（CDB）三种RAFT试剂作为链转移剂的苯乙烯本体聚合。动力学研究表明,当BDB及PEDB浓度和偶氮二异丁腈（AIBN）浓度同时增大时,AIBN浓度提高所导致的聚合反应速率提高起主导作用：当CDB和AIBN浓度同时提高时,CDB浓度提高所导致的聚合速率降低作用影响更显著。对CDB体系,随转化率提高分子量分布变宽。对BDB体系,当其浓度较高时,随转化率提高分子量分布变窄;当其浓度较低时,不利于实现可控,活性聚合,反应后期分子量分布变宽。动力学和GPC分析均表明以BDB为链转移剂时苯乙烯本体聚合的可控性最好。在同时考虑链转移剂和引发剂作用的基础上,提出了修正的聚合物分子量预测模型,该模型可有效预测以双硫酯为链转移剂的苯乙烯RAFT聚合体系的分子量。     

Calorimetric study on the influence of the nature of the RAFT agent and the initiator in ab initio aqueous heterophase polymerization

Experimental results regarding reaction rate profiles and final latex and polymer properties are presented for combinations of four different RAFT agents [benzyl dithioacetate (BDA), benzyl dithiobenzoate (BDB), 1-phenyl ethyl dithiobenzoate (PhEDB), and cumyl dithiobenzoate (CDB)] and three types of initiators [potassium peroxodisulfate (KPS), 4,4′-azobis (4-cyanopentanoic acid) (ACPA), and poly(ethylene glycol)-azo-initiator (PEGA200)]. It was found out that at given type of RAFT agent the type of initiator has a strong influence on the reaction rate profiles as well as on both the molecular properties of the polymers and the colloidal properties of the latexes. Among the RAFT agents tested BDA is the most efficient one regarding the control of chain growth.     

RAFT polymerization of styrene mediated by naphthalene-containing RAFT agents and optical properties of the polymers

In this paper, we designed and synthesized five novel reversible addition–fragmentation chain transfer (RAFT) agents bearing naphthyl moieties in the Z or R groups, including 3,4,5-trimethoxy-benzyl dithio-2-naphthalenoate (TOBDN), 4-nitrobenzyl dithio-2-naphthalenoate (NBDN), 1-menaphthyl 4-cyanodithiobenzoate (NCDB), 1-menaphthyl dithiobenzoate (NDB) and 1-menaphthyl dithio-2-naphthalenoate (NDN). The RAFT polymerizations of styrene mediated by these RAFT agents with AIBN as the initiator at 80 °C were conducted and evaluated. Except for NCDB, the RAFT agents showed good control over the polymerization at different RAFT agent concentrations: the M_n,GPC increased linearly with the monomer conversion, and the PDIs of the polymers were relatively low (PDI = 1.20–1.50). The structure of RAFT agents bearing three different R groups with naphthyl as the Z group showed less effects on the polymerization rate, while those bearing different Z groups with 1-menaphthyl as the R group presented significant effects on the polymerization rates. The polymerization rate with phenyl as the Z group was higher than that with 2-naphthyl as the Z group, and it decreased significantly when using 4-cycno phenyl as the Z group. Retardation effects were observed with all the RAFT agents. ¹H NMR spectra and chain extension results confirmed that most of the polymer chains were “living”. Ultraviolet (UV) absorption of naphthyl moieties at the R group showed blue shifts compared with those of naphthyl at the Z group. The UV absorption intensity of PS was uniformly lower than that of the corresponding RAFT agent, while the fluorescence intensity of PS was higher than that of the corresponding RAFT agent.     

Synthesis of well-defined poly( n -vinylpyrrolidone)/n-TiO 2 nanocomposites by xanthate-mediated radical polymerization

For the first time formation of well-defined poly n-vinylpyrrolidone/n-TiO2 nanocomposite by xanthate-mediated radical polymerization was accomplished. The synthesis of polymer nanocomposite materials has been intensively studied due to their extraordinary properties and wide-spread potential applications. For this purpose, first 2‐propionic acid-O-ethyl xanthate, as a RAFT agent, was synthesized by the reaction of 2-bromopropionic acid with potassium O-ethyl xanthate with acetone as the solvent. A carboxylic group in the RAFT agent was attached to the n-TiO2 surface by metalation reaction. Then, RAFT polymerization of n-vinylpyrrolidone (NVP) was subsequently conducted to graft poly(n-vinylpyrrolidone) (PNVP) onto the exterior surface of n-TiO2 nanoparticles, forming a novel core–shell nanostructure with a mesoporous core and a polymeric nanoshell. The viscosimetry data and 1H NMR spectra were used to calculate the molecular weight of the polymer. The obtained results showed a good agreement withthe methods used. A significant enhancement in the stability of the composites was obtained as demonstrated by the TGA results. The SEM and TEM results showed that the polymer was formed on the surface of the particles. The XRD pattern of the nanoparticles of n-TiO2 presented the amorphous structure of the crystal morphology of the composites. The FTIR and UV–visible spectroscopy results proved that the PNVP chains were grafted onto the n-TiO2 nanoparticles by surface RAFT polymerization.     

A new selenium-based RAFT agent for surface-initiated RAFT polymerization of 4-vinylpyridine

A new selenium-based reversible addition-fragmentation chain transfer (RAFT) agent, 4-cyanopentanoic acid diselenobenzoate (RAFT-Se), was synthesized and utilized in the surface-initiated RAFT polymerization of 4-vinylpyridine (4VP) on silicon substrate. The results indicate that the RAFT-Se can control the surface-initiated RAFT polymerization, as evidenced by the number-average molecular weight that increase linearly with monomer conversion, molecular weights that agreed well with the predicted values, and the relatively low polydispersity indexes. The surface-initiated RAFT polymerization with the RAFT-Se was the same polymerization mechanism as its analog, 4-cyanopentanoic acid dithiobenzoate (RAFT-S). The grafting density of the poly(4-vinylpyridine) brushes prepared in the presence of RAFT-Se (σ_RAFT-Se) and RAFT-S (σ_RAFT-S) was estimated to be about 0.51 and 0.66 chains/nm², respectively. In addition, the end of polymer chains on silicon substrate contains selenium element which may be useful in biosensor applications.     

Using dilatometry in the reversible addition fragmentation transfer polymerization of N-(S)-(−)-α-methylbenzyl methacryloylamine

Optically active polymers were prepared using reversible addition-fragmentation chain transfer polymerization (RAFT) of N-(S)-α-methylbenzylmethacryloylamine (N-(S)-α-MBMA), a functional optically active monomer. RAFT polymerizations were carried out at 70 °C in ethanol using AIBN as a thermal initiator and benzyl or (1-phenyl)ethyl dithiobenzoate (BDB and PEDB, respectively) as the RAFT agents. The kinetic study was performed by dilatometry. Plots of conversion vs time indicated that the polymerizations followed first order kinetics. ¹H NMR, IR, and UV–vis spectrophotometric studies confirmed the presence of thiocarbonylthio moieties (−SCS-) in the polymer chains. The molecular weight distributions (MWDs) were moderately narrow with polydispersity indices between 1.3 and 1.6, which indicated that the control of the reaction was not completely achievement using BDB or PEDB as RAFT agents. The optical activity [α]_D²⁵ measurements of synthesized polymers by RAFT did not show a noticeably linear increase dependence with respect to molecular weight, as was previously reported for another controlled free radical polymerization (CRP) system.     

Comparison of RAFT polymerization of methyl methacrylate in conventional emulsion and miniemulsion systems

In this study, we have conducted the reversible addition-fragmentation chain transfer (RAFT) polymerization of methyl methacrylate (MMA) in two heterogeneous systems, i.e. conventional emulsion and miniemulsion, with identical reaction conditions. The main objective is to compare the living character in both systems according to the nucleation mechanism, the latex stability, the particle sizes and particle size distributions of latexes, the molecular weights and molecular weight distributions (or polydispersity index, PDI) of PMMA, and the kinetics of the RAFT polymerization. The RAFT agent used in both systems was 2-cyanoprop-2-yl dithiobenzoate (CPDB). The effects of an oil-soluble initiator 2,2′-azobisisobutyronitrile (AIBN) and a water-soluble initiator kalium persulfate (KPS) on the RAFT/emulsion and RAFT/miniemulsion polymerizations were investigated. Methyl-β-cyclodextrin (Me-β-CD) was used as a solubilizer. The average molecular weights and molecular weight distributions (PDIs) of dried PMMA samples were characterized by gel permeation chromatography (GPC). The experimental results showed that the RAFT/miniemulsion polymerization of MMA exhibited better living character than that of RAFT/emulsion polymerization under the conditions of our experiment. The PDI of PMMA in RAFT/miniemulsion polymerization was decreased with the addition of Me-β-CD. However, Me-β-CD did not have influence on the PDI of PMMA prepared in RAFT/emulsion polymerization.     

Soap-free emulsion polymerization of styrene using poly(methacrylic acid) macro-RAFT agent

A well-defined poly(methacrylic acid) (PMAA) macro-RAFT agent has been synthesized by the bulk polymerization using 4-toluic acid dithiobenzoate as a RAFT agent and successfully employed as a reactive emulsifier in the soap-free emulsion polymerization of styrene, leading to a formation of stable latex. The amphiphilic block copolymer, prepared from the in situ micelle formation, contains a hydrophilic PMAA block and a hydrophobic PS block, via styrene monomer transfer reaction to the dithioester function in PMAA macro-RAFT agent during the nucleation step. The chemical structure of the synthesized PS with the PMAA macro-RAFT agent was confirmed using FTIR and NMR. In addition, it was confirmed that the macro-RAFT agent is present on the particle surface via the ESCA measurement. The reaction mechanism was proposed that the stable spherical particles enlarged by the aggregation of small particles, which were also produced by the chemical or physical bonding between the tiny small particles. The results indicate that the PMAA macro-RAFT agent is used as emulsifier for the formation of PS particles and block copolymer [P(S-b-MAA)] in situ.     

Versatile method via reversible addition‐fragmentation transfer polymerization for synthesis of poly styrene/ZnO–nanocomposite

Reversible addition‐fragmentation chain transfer (RAFT) polymerization enables the synthesis of controlled architectures for a wide‐variety of polymers with defined end and pendant functionalities using mild conditions. A simple synthetic route for the preparation of polystyrene (PS)/ZnO nanocomposite with well‐defined structure is demonstrated. ZnO nanoparticles were synthesized by homogeneous precipitation. To reduce the aggregation among ZnO nanoparticles, an effective surface modification method was proposed by grafting polystyrene onto the ZnO particles. The surface of ZnO nanoparticles was firstly treated with a 4‐cyano‐4‐[(4‐methoxyphenyl carbon thiol) solfanylvaleric acid] coupling RAFT agent in the presence of THF as a solvent at 65°C. A carboxylic group in raft agent attached to ZnO nanoparticles by the esterification reaction with the hydroxyl groups on the ZnO particle surface. Then, RAFT polymerization of styrene was subsequently conducted to graft PS onto the exterior surface of ZnO nanoparticles by new RAFT agent 4‐cyano‐4‐[(4‐methoxyphenyl carbon thiol) solfanylvaleric acid]. The obtained nanocomposite was characterized by Fourier transform infrared spectroscopy (FT‐IR), thermo gravimetric (TGA), transmission electron microscopy (TEM), and X‐ray powder diffraction (XRD). POLYM. ENG. SCI., 56:187–195, 2016. © 2015 Society of Plastics Engineers     

Low protein fouling polypropylene membrane prepared by photoinduced reversible addition‐fragmentation chain transfer polymerization

In this study, 2‐hydroxyethyl methacrylate and N‐isopropyl acrylamide was block grafted onto the polypropylene macroporous membrane surface by photo‐induced reversible addition‐fragmentation chain transfer (RAFT) radical polymerization with benzyl dithiobenzoate as the RAFT agent. The degree of grafting of poly(2‐hydroxyethyl methacrylate) on the membrane surface increased with UV irradiation time and decreased with the chain transfer agent concentration increasing. The poly(2‐hydroxyethyl methacrylate)‐ grafted membranes were used as macro chain transfer agent for the further block graft copolymerization of N‐isopropyl acrylamide in the presence of free radical initiator. The degree of grafting of poly(N‐isopropyl acrylamide) increased with reaction time. Furthermore, the poly(2‐hydroxyethyl methacrylate)‐ grafted membrane with a degree of grafting of 0.48% (wt) showed the highest relative pure water flux and the best antifouling characteristics of protein dispersion. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Novel Malachite Green- and Rhodamine B-labeled cationic chain transfer agents for RAFT polymerization

Two novel cationic RAFT agents have been synthesized, one labeled with a Malachite Green (MG) dye and another with a Rhodamine B (RhoB) dye. MG-labeled dithiobenzoate (MGEDBA) was prepared in a straightforward manner after synthesis of MG-ethylammonium chloride that reacted with a precursor dithiobenzoate bearing an activated ester function. However, the analogous reaction with RhoB amino derivative led to a mixture of dithiobenzoate and thioamide derivatives. An alternative approach yielded the RhoB-labeled RAFT agent (RhoBEDBA) with complete conversion. The purification of these dye-labeled RAFT agents was very challenging because of their dual nature (aromatic and ionic). Both MGEDBA and RhoBEDBA were efficient RAFT chain transfer agents to control the polymerization of N,N-dimethylacrylamide (DMA). The resulting α-end-labeled MG- and RhoB-PDMA samples presented low dispersities (?<1.2) and both chain-ends were preserved. Finally, we showed that the attachment of RhoB and MG to the PDMA polymer chain-end did not influence the photophysical properties of these dyes. Therefore, these new dye-labeled RAFT agents can be used to prepare various labeled polymers and especially water-soluble ones, to study their conformation and dynamics in solution or at interfaces using fluorescence methods, or as labeled probes for imaging and/or diagnosis purposes.     

Controlled synthesis of vinyl-functionalized homopolymers and block copolymers by RAFT polymerization of vinyl methacrylate

Reversible addition-fragmentation chain transfer (RAFT) polymerization of an asymmetrical divinyl monomer, vinyl methacrylate (VMA), was investigated under various conditions. RAFT polymerization of VMA using a dithioester-type chain transfer agent (CTA) under suitable conditions afforded soluble polymers with a high content of pendant vinyl ester side chains in sufficient yields (>70%). The monomer concentration, the nature of the CTA, and the CTA/initiator ratio were found to affect the polymerization reaction and the structure of the resulting polymers; this behavior is attributed to the relative propensities for intermolecular propagating/cross-linking reactions and intramolecular cyclization. A kinetic study of the RAFT polymerization of VMA with the dithioester-type CTA 1 suggested that the propagation reaction of the methacryloyl group proceeded predominantly with a certain level of intramolecular cyclization during the early stage of the polymerization and intermolecular cross-linking during the final stage of the polymerization. Block copolymers with one segment featuring pendant vinyl functionality were synthesized by RAFT polymerization of VMA using poly(methyl methacrylate) as a macro-chain transfer agent (macro-CTA).     

Synthesis of hybrid TiO2 nanoparticles with well-defined poly(methyl methacrylate) and poly(tert-butyldimethylsilyl methacrylate) via the RAFT process

Surface of titania nanoparticles (TiO₂) was modified by a coupling agent as 3-(trimethoxysilyl)propyl methacrylate (MPS) to form TiO₂-MPS polymerizable particles. Methyl methacrylate (MMA) and tert-butyldimethylsilyl methacrylate (MASi) were radically polymerized through the immobilized vinyl bond on the surface in the presence of the reversible addition-fragmentation chain transfer (RAFT) agent 2-cyanoprop-2-yl dithiobenzoate using 2,2′-azobisisobutylnitrile (AIBN) as an initiator. FTIR spectroscopy confirmed the presence of the coupling molecule and the methacrylate groups on the surface. Thermogravimetric analysis and elemental analysis revealed a surface coverage of the coupling molecule of 2.0 wt%. TGA measurements showed that grafted PMMA and PMASi were accounted for 10% and 4.8% of the particle mass, respectively. ¹H NMR and SEC were used to verify the livingness of the polymerization. Transmission electron microscopy (TEM) was used to study the morphology of the particles before and after the surface grafting.     

Effect of stabilizer concentration and controller structure and composition on polymerization rate and molecular weight development in RAFT polymerization of styrene in supercritical carbon dioxide

An experimental study on the reversible addition-fragmentation chain transfer (RAFT) polymerization of styrene in supercritical carbon dioxide is presented. A 38 mL, high-pressure view cell with two frontal and two lateral sapphire windows was used as reactor. Poly(styrene-block-dimethylsiloxane) was used as stabilizer. The performance as RAFT controllers of S-thiobenzoyl thioglycolic acid, methyl naphthalene dithiobenzoate, 4-methyl allyl dithiobenzoate, and benzyl-N,N-dimethyldithiocarbamate was compared. The effect of stabilizer concentration and controller structure and concentration on polymerization rate and molecular weight development was analyzed. Good performance was obtained with the first three controllers, although simultaneous high polymerization rates and low polydispersities were not possible with either of them. The performance of the fourth RAFT controller was poor.     

Grafting modification of ramie fibers with poly(2,2,2-trifluoroethyl methacrylate) via reversible addition–fragmentation chain transfer (RAFT) polymerization in supercritical carbon dioxide

Reversible addition–fragmentation chain transfer (RAFT) polymerization was used to control the grafting of 2,2,2-trifluoroethyl methacrylate (TFEMA) with ramie fibers in supercritical carbon dioxide (scCO₂). The hydroxyl groups of the ramie fibers were converted to 2-dithiobenzoyl isobutyrate as the RAFT chain transfer agent (cellulose-CTA). Then, the subsequent grafting with TFEMA was mediated by RAFT polymerization in the presence of 2-(ethoxycarbonyl)prop-2-yl dithiobenzoate (ECPDB) as the free RAFT chain transfer agent (free CTA). The modified ramie fibers were highly hydrophobic with water contact angles of up to 149°. Size exclusion chromatography showed narrow polydispersity (PDI = 1.28) of the grafted poly(TFEMA) chains. This grafting polymerization process is a novel and environmentally friendly approach for the preparation of functional grafted copolymers utilizing ramie fiber biomass.     

Preparation of star polymers based on polystyrene or poly(styrene-b-N-isopropyl acrylamide) and divinylbenzene via reversible addition-fragmentation chain transfer polymerization

Star polymers based on styrene/divinyl benzene (St/DVB) and PSt-b-poly(N-isopropyl acrylamide) (NIPAAM)/DVB have been successively prepared by ‘arm-first’ method via reversible addition-fragmentation chain transfer (RAFT) polymerization. The linear macro RAFT agent PSt-SC(S)Ph was prepared by RAFT polymerization of St using benzyl dithiobenzoate and AIBN as RAFT agent and initiator. Successive RAFT polymerization of NIPAAM with PSt-SC(S)Ph as macro RAFT agent to afford diblock copolymer, PSt-b-PNIPAAM-SC(S)Ph. The coupling reactions of PSt-SC(S)Ph or PSt-b-PNIPAAM-SC(S)Ph in the presence of DVB produced the star copolymers, C(PSt)_n or C(PSt-b-PNIPAAM)_n. The molar ratio of DVB/PSt-SC(S)Ph and polymerization time influenced the yields, molecular weight and distribution of the star-shaped polymers, which was characterized by ¹H NMR and IR spectra, GPC measurements as well as DLS.     

Surface‐initiated atom transfer radical polymerization (ATRP) of styrene from silica nanoparticles under UV irradiation

Diethyldithiocarbamyl‐modified silica nanoparticles were prepared and used as macroinitiator for the surface‐initiated atom transfer radical polymerization (SI‐ATRP) of styrene under UV irradiation. Well‐defined polymer chains were grown from the nanoparticle surfaces to yield particles composed of a silica core and a well‐defined, densely grafted outer PS layer with a mass ratio of styrene to silica, or percentage grafting, of 276.3% after an UV irradiation time of 5 h. Copyright © 2004 Society of Chemical Industry     

Synthesis of graphene-polystyrene nanocomposites via RAFT polymerization

Synthesis of graphene-polymer nanocomposites is of current interest due to their exceptionally physical and chemical properties. However, the ability to produce conductive inks/coatings retaining the properties of the graphene is still a major challenge. In this study, functionalized polydopamine-coated reduced graphene oxide (PDA/RGO) was reacted with a RAFT agent, 2-(dodecylthiocarbonothioylthio)-2-methylpropionic acid (DDMAT), to form macro-RAFT agents via an esterification reaction. The chemistry and kinetics of RAFT living/controlled polymerization of styrene was examined from the surface of these macro-RAFT agents to form polystyrene-grafted PDA/RGO (PS-g-PDA/RGO). By examination of the kinetics and GPC traces of the free and grafted polymer, living/controlled polymerization was confirmed. To examine the utility of this approach, the synthesized PS-g-PDA/RGO samples containing different amounts of grafted PS were employed in the preparation of graphene-PS nanocomposites by mixing them with commercial PS. Graphene was found to be well distributed in the PS matrix by this approach, increasing the decomposition temperature range. This research provides an efficient route towards the design and development of value-added functional graphene-PS composites.     

Preparation of well‐defined block copolymer having one polystyrene segment and another poly(styrene‐alt‐maleic anhydride) segment with RAFT polymerization

Block copolymers, polystyrene‐b‐poly(styrene‐co‐maleic anhydride), have been prepared by reversible addition‐fragmentation chain transfer (RAFT) polymerization technique using three different approaches: 1‐phenylethyl phenyldithioacetate (PEPDTA) directly as RAFT agent, mediated polystyrene (PS) block as the macromolecular PS‐RAFT agent and mediated poly(styrene‐maleic anhydride) (SMA) block with alternating sequence as the macromolecular SMA‐RAFT agent. Copolymers synthesized in the one‐step method using PEPDTA as RAFT agent possess one PS block and one SMA block with gradient structure. When the macromolecular RAFT agents are employed, copolymers with one PS block and one alternating SMA block can be produced. However, block copolymers with narrow molecular weight distribution (MWD) can only be obtained using the PS‐RAFT agent. The MWD deviates considerably from the typical RAFT polymerization system when the SMA is used as the RAFT agent. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011