One-pot synthesis of poly(methacrylic acid)-b-poly(2,2,2-trifluoroethyl methacrylate) diblock copolymers via RAFT polymerization

In this work, the reversible addition-fragmentation chain transfer (RAFT) polymerization was utilized to synthesize the amphiphilic diblock copolymers of poly(methacrylic acid)-b-poly(2,2,2-trifluoroethyl methacrylate) (PMAA-b-PTFEMA) via one-pot two-step reaction protocol. The controlled radical polymerization of MAA monomer was first carried out in pure water by using 4-cyanopentanoic acid dithiobenzoate (CADB) as chain transfer agent. Subsequently, the as-synthesized PMAA homopolymers with dithiobenzoate end-groups were employed as macro-CTA and chain-extended in situ with the hydrophobic TFEMA monomer. The reactions were carried out in 1,4-dioxane/water medium. Both the polymerization of PMAA and PTFEMA blocks showed the well controllability on the molecular weighs and distributions. It was found that the amphiphilic diblock copolymers formed the stable spherical particles via the polymerization-induced self-assembly. Meanwhile, the effect of various parameters, such as the concentration ratio of TFEMA monomer over PMAA macro-CTA, the solvent condition (different ratio of 1,4-dixane/water), and the pH, on the RAFT polymerization of TFEMA monomer were investigated in detail. Their kinetic results suggested that the propagation of TFEMA monomer on the macro-CTA was performed at the particle/water interfaces. The concentration of chain transfer agents at the interfaces determined the polymerization rate. Finally, the stability of the fluorinated polymer dispersions was also evaluated in this work.     

pH- and temperature-responsive amphiphilic diblock copolymers of 4-vinylpyridine and oligoethyleneglycol methacrylate synthesized by RAFT polymerization

Diblock copolymers of 4-vinylpyridine (4VP) and oligoethyleneglycol methyl ether methacrylate (OEGMA) were synthesized for the first time using RAFT polymerization technique as potential drug delivery systems. Effects of the number of ethylene glycol units in OEGMA, chain length of hydrophobic P4VP block, pH, concentration and temperature on the solution behavior of the copolymers were investigated comprehensively. Copolymer chains formed micelles at pH values higher than 5 whereas unimeric polymers were observed to exist below pH 5, owing to the repulsion between positively charged P4VP blocks. The size of the micelles was dependent on the relative length of blocks, P4VP and POEGMA. Thermo-responsive properties of copolymers were investigated depending on the pH and length of P4VP block. The increase in the length of P4VP block decreased the LCST substantially at pH 7. At pH 3, LCST of copolymers shifted to higher temperatures due to the increased interaction of copolymers with water through positively charged P4VP block.     

One-step synthesis of poly(2-oxazoline)-based amphiphilic block copolymers using a dual initiator for RAFT polymerization and CROP

A range of poly(2-oxazoline) (POx)-based amphiphilic block copolymers were synthesized using 4-cyano-4-(dodecylthiocarbonothioylthio)pentyl-4-methylbenzenesulfonate (CDPS) as a dual initiator for reversible addition-fragmentation chain transfer (RAFT) polymerization and cationic ring-opening polymerization (CROP) in a one-step procedure. Methyl (meth)acrylate, butyl (meth)acrylate, tert-butyl (meth)acrylate, and N-isopropylacrylamide were polymerized for the hydrophobic block, and 2-methyl-2-oxazoline and 2-ethyl-2-oxazoline were used as the hydrophilic block. RAFT polymerization and CROP proceeded independently in a controlled manner and resulted in amphiphilic block copolymers with a narrow molecular weight distribution. CDPS was found to be a useful dual initiator for the one-step synthesis of POx-based amphiphilic block copolymers via a combination of RAFT polymerization and CROP.     

Synthesis and pH-dependent micellization of 2-(diisopropylamino)ethyl methacrylate based amphiphilic diblock copolymers via RAFT polymerization

The polymerization of 2-(diisopropylamino)ethyl methacrylate (DPA) by RAFT mechanism in the presence of 4-cyanopentanoic acid dithiobenzoate in 1,4-dioxane was studied. The DPA homopolymer was employed as a macro chain transfer agent to synthesize pH-sensitive amphiphilic block copolymers using poly(ethylene glycol) methyl ether methacrylate (PEGMA) as the hydrophilic block. ¹H NMR and GPC measurements confirmed the successful synthesis of these copolymers. Potentiometric titrations and fluorescence experiments proved that the copolymers underwent a sharp transition from unimers to micelles at a pH of ∼6.7 in phosphate buffered saline solutions. It was found that the hydrophilic/hydrophobic balance of these block copolymers had no apparent effect on their pH-induced micellization behaviors. The DLS investigation revealed that the micelles have a mean hydrodynamic diameter below 60 nm with a narrow size distribution.     

Controlled/living RAFT polymerization of N‐phenyl maleimide and synthesis of its block copolymers

The controlled/living radical polymerization of N‐phenyl maleimide (NPMI) was achieved using 2,2′‐azobisisobutyronitrile as the initiator and 2‐cyanopropyl‐2‐yl dithiobenzoate as the reversible addition‐fragmentation chain transfer agent at 75°C in dichloroethane/ethylene carbonate (60/40, w/w) mixed solvent. The block copolymers of polystyrene‐b‐polyNPMI and poly(n‐butyl methacrylate)‐b‐polyNPMI were successfully prepared by chain extension from dithiobenzoate‐terminated polystyrene and poly (n‐butyl methacrylate) to NPMI, respectively. The obtained NPMI‐based (co)polymers were characterized by gel permeation chromatography and ¹H‐NMR spectroscopy. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Synthesis of structured nanoparticles of styrene/butadiene block copolymers via RAFT seeded emulsion polymerization

The structured nanoparticles of styrene (St) and butadiene (Bd) block copolymers were prepared by RAFT seeded emulsion polymerization of butadiene. It was confirmed that the block copolymers of PSt-b-P(St-co-Bd) was formed with controlled molecular weight and rather low PDI at low composition of the P(St-co-Bd) segment. With more incorporation of butadiene, the branching reaction of polybutadiene became obvious, leading to higher PDI and positive deviation of M_n from the theoretical predication. At the gel point, the composition of the P(St-co-Bd) segment was estimated to be 0.72. After this, the gel fraction increased quickly. The morphology of structured nanoparticles could be largely tuned simply by the copolymer composition. With the composition of the P(St-co-Bd) segment increased from 0.37 to 0.92, the morphology within the structured particles changed from the polybutadiene domains-in-polystyrene matrix, perforated concentric-spherical layer, concentric-spherical multi-layers, bi-continuous, to broken layers of polystyrene in polybutadiene matrix. It was found that the morphology of the block copolymer within nanoparticles was dependent on d/L values, which was in excellent agreement with the theoretical prediction.     

Synthesis and characterization of biodegradable and biocompatible amphiphilic block copolymers bearing pendant amino acid residues

Polylactide (PLA)-based biodegradable and biocompatible amphiphilic block copolymers bearing pendant amino acid residues were synthesized through a relatively easy and efficient way. The composition and structure of these copolymers were characterized by gel permeation chromatography (GPC) and ¹H nuclear magnetic resonance (¹H NMR) spectroscopy. The self-assembly behavior of the copolymers was investigated by fluorescence (FL), dynamic light scattering (DLS), and transmission electron microscope (TEM). It was shown that aggregates less than 100 nm in average size were formed by these copolymers, which changed from micelles to vesicles with the variation of the block length. In addition, the in vitro cytotoxicity of these copolymers was determined and compared with that of PEO-b-PLA in the presence of Bel-7402 cells. The result suggested that the block copolymers PAGE/cys-b-PLA exhibited better biocompatibility. Therefore, these PLA-based copolymers are expected to find promising applications in drug delivery or tissue engineering.     

Synthesis and self-assembly behaviors of three-armed amphiphilic block copolymers via RAFT polymerization

The novel trifunctional reversible addition-fragmentation chain transfer (RAFT) agent, tris(1-phenylethyl) 1,3,5-triazine-2,4,6-triyl trithiocarbonate (TTA), was synthesized and used to prepare the three-armed polystyrene (PS₃) via RAFT polymerization of styrene (St) in bulk with thermal initiation. The polymerization kinetic plot was first order and the molecular weights of polymers increased with the monomer conversions with narrow molecular weight distributions (M_w/M_n ≤ 1.23). The number of arms of the star PS was analyzed by gel permeation chromatography (GPC), ultraviolet visible (UV-vis) and fluorescence spectra. Furthermore, poly(styrene-b-N-isopropylacrylamide)₃ (PS-b-PNIPAAM)₃, the three-armed amphiphilic thermosensitive block copolymer, with controlled molecular weight and well-defined structure was also successfully prepared via RAFT chain extension method using the three-armed PS obtained as the macro-RAFT agent and N-isopropylacrylamide as the second monomer. The copolymers obtained were characterized by GPC and ¹H nuclear magnetic resonance (NMR) spectra. The self-assembly behaviors of the three-armed amphiphilic block copolymers (PS-b-PNIPAAM)₃ in mixed solution (DMF/CH₃OH) were also investigated by high performance particle sizer (HPPS) and transmission electron microscopy (TEM). Interestingly, the lower critical solution temperature (LCST) of aqueous solutions of the three-armed amphiphilic block copolymers (PS-b-PNIPAAM)₃ decreased with the increase of relative length of PS in the block copolymers.     

Poly(N-tert-butyl acrylamide-b-N-acryloylmorpholine) amphiphilic block copolymers via RAFT polymerization: Synthesis, purification and characterization

Amphiphilic block copolymers consisting of two poly(acrylamide) derivative blocks have been synthesized via the reversible addition fragmentation chain transfer (RAFT) polymerization process with a hydrophobic block, poly(N-tert-butyl acrylamide), poly(TBAm), and a non-ionic hydrophilic one, poly(N-acryloylmorpholine), poly(NAM). Both polymerization orders, poly(TBAm-b-NAM) and poly(NAM-b-TBAm), were compared in terms of conversion and control over molecular weights (MW). Purification of the block copolymers was carried out via several methods in order to optimize their subsequent characterization. ¹H NMR analysis resulted in an accurate determination of the second block MW whereas determination of the CMC by the pendant drop method confirmed the ability of the poly(TBAm-b-NAM) block copolymers to self-assemble into micelles in aqueous phase.     

Synthesis of poly(trioctylammonium p-styrenesulfonate) homopolymers and block copolymers by RAFT polymerization

A method to prepare sulfonated polystyrene-containing block copolymers has been investigated by neutralizing styrene sulfonic acid with trioctylamine to produce the hydrophobic monomer trioctylammonium p-styrenesulfonate (SS-TOA). This monomer was polymerized by reversible addition fragmentation chain transfer (RAFT) polymerization to produce PSS-TOA homopolymers. A PSS-TOA homopolymer was then used as a macro-RAFT agent for the polymerization of styrene to prepare poly(trioctylammonium p-styrenesulfonate)-block-poly(styrene) (PSS-TOA-b-PS). These block copolymers could be ion-exchanged to produce either the hydrophilic sodium salt form of PSS or a hydrophobic quaternary ammonium salt. This approach will be useful for preparing PSS-containing block copolymers with a range of hydrophobic blocks for applications such as ion-exchange membranes.     

The amphiphilic block copolymers of 2-(dimethylamino)ethyl methacrylate and methyl methacrylate: Synthesis by atom transfer radical polymerization and solution properties

Amphiphilic di- and tri-block copolymers of poly(methyl methacrylate) (PMMA) and poly(2-dimethylamino)ethyl methacrylate (PDMAEMA) have been synthesized by atom transfer radical polymerization (ATRP) at ambient temperature (35 °C) in the environment-friendly solvent, aqueous ethanol (water 16 vol%) using CuCl/o-phenanthroline as the catalyst. The PDMAEMA blocks are contaminated with ethyl methacrylate (EMA) residues to the extent of 1-2 mol% of DMAEMA depending on the length of the PDMAEMA block. The EMA forms through the autocatalyzed ethanolysis of the DMAEMA monomer and undergoes random copolymerization with the latter. The rate of ethanolysis is unexpectedly greater in the aqueous ethanol than in neat ethanol, which has been attributed to the higher polarity of the former than of the latter. In contrast to the ethanolysis no hydrolysis of DMAEMA in the aqueous ethanol medium could be detected for 133 h. The block copolymers form micelles in water. Their solubility and CMC in neutral water have been studied. Dynamic light scattering (DLS) studies reveal that for a fixed degree of polymerization (DP) of the PMMA block the hydrodynamic diameter of the micelles in methanolic water (water 95 vol%) increases at a faster rate with the DP of the PDMAEMA block when it is much greater than that of the PMMA block compared to when it is less than or close to that of the latter.     

Controlled synthesis of vinyl-functionalized homopolymers and block copolymers by RAFT polymerization of vinyl methacrylate

Reversible addition-fragmentation chain transfer (RAFT) polymerization of an asymmetrical divinyl monomer, vinyl methacrylate (VMA), was investigated under various conditions. RAFT polymerization of VMA using a dithioester-type chain transfer agent (CTA) under suitable conditions afforded soluble polymers with a high content of pendant vinyl ester side chains in sufficient yields (>70%). The monomer concentration, the nature of the CTA, and the CTA/initiator ratio were found to affect the polymerization reaction and the structure of the resulting polymers; this behavior is attributed to the relative propensities for intermolecular propagating/cross-linking reactions and intramolecular cyclization. A kinetic study of the RAFT polymerization of VMA with the dithioester-type CTA 1 suggested that the propagation reaction of the methacryloyl group proceeded predominantly with a certain level of intramolecular cyclization during the early stage of the polymerization and intermolecular cross-linking during the final stage of the polymerization. Block copolymers with one segment featuring pendant vinyl functionality were synthesized by RAFT polymerization of VMA using poly(methyl methacrylate) as a macro-chain transfer agent (macro-CTA).     

Synthesis and characterization of pH/temperature-sensitive block copolymers via atom transfer radical polymerization

In order to prepare well-defined pH-sensitive block copolymers with a narrow molecular weight distribution (MWD), we synthesized a pH-sensitive block copolymer via atom transfer radical polymerization (ATRP) of sulfamethazine methacrylate monomer (SM) and amphiphilic diblock copolymers by the ring-opening polymerization of d,l-lactide/?-caprolactone (LA/CL), and their sol-gel phase transition was investigated. SM, which is a derivative of sulfonamide, was used as a pH responsive moiety, while PCLA-PEG-PCLA was used as a biodegradable, as well as a temperature sensitive one, amphiphilic triblock copolymer. The pentablock copolymer, OSM-PCLA-PEG-PCLA-OSM, was synthesized using Br-PCLA-PEG-PCLA-Br as an ATRP macroinitiator. The number average molecular weights of SM were controlled by adjusting the monomer/initiator feed ratio. The macroinitiator was synthesized by the coupling of 2-bromoisobutyryl bromide with PCLA-PEG-PCLA in the presence of triethyl amine catalyst in dichloromethane. The resultant block copolymer shows a narrow polydispersity. The block copolymer solution shows a sol-gel transition in response to a slight pH change in the range of 7.2-8.0. Gel permeation chromatography (GPC) and NMR were used for the characterization of the polymers that were synthesized.     

New self-assembling biocompatible-biodegradable amphiphilic block copolymers

New biodegradable-biocompatible amphiphilic block copolymers were prepared in good yields by SnOct₂ catalyzed ring opening polymerization of ε-caprolactone initiated by monomethoxy-terminated poly(ethylene glycol) (MPEG). Coupling of the AB copolymers with hexamethylene diisocyanate afforded ABA (formally ABBA) block copolymers. Both AB and ABA copolymers were thoroughly characterized by IR and NMR spectroscopy, size exclusion chromatography, TGA and DSC thermal analysis. In particular, DSC measurements evidenced that the copolymer hydrophilic-lipophilic balance appreciably affected the state of adsorbed water. Polarized optical microscopy of bulk materials and pyrene fluorescence emission of polymer water solutions highlighted the copolymer tendency to phase separation and self-organization, respectively. Most of the prepared materials formed micelles in water and the copolymer structure appreciably affected their critical micellar concentration. In vitro cytocompatibility tests confirmed the low toxicity of the prepared polymeric materials which enhances their potential for biomedical applications.     

Facile preparation of amphiphilic oxyethylene-oxypropylene block copolymers by selective triazine coupling

A novel synthetic route for preparing high molecular weight poly(oxyalkylene) block copolymers has been developed by using 2,4,6-trichloro-1,3,5-triazine (cyanuric chloride, cc) as the coupling core. The coupling reaction involves the selective substitutions of oligo(oxyalkylene)-amines onto three chlorides of the triazine ring in a stepwise manner at 0, 25 and 130 °C. By judiciously selecting the starting amines and reaction conditions, one can tailor the copolymer structures with different block configurations (tri-block, multi-block, random and alternating block). The prepared copolymers can have a high molecular weight, up to 25,600 g/mol (GPC polydispersity=1.48), and also high thermal stability due to the presence of triazine functionalities. The copolymers with hydrophilic and hydrophobic oligo(oxyalkylene) blocks are of versatile properties in solubility (water soluble or water insoluble) and morphology (crystalline or amorphous). With a specific structure of alternating oligo(oxyethylene)/oligo(oxypropylene) blocks (2000 g/mol each block), the copolymer exhibits the property of self-association. It reduces the interfacial tension of toluene/water as low as 0.5 dyne/cm at the critical micelle concentration of 0.01 wt%.     

Water-assisted formation of honeycomb structured porous films

Honeycomb structured porous materials were formed using four different casting variations of the water droplet templating method. The film quality of the materials generated from these casting techniques (airflow, cold stage, casting on water, and emulsion methods) was investigated by altering the polymer architecture and composition. Linear, star, and comb polystyrene as well as an amphiphilic diblock copolymer comprised of polystyrene-block-poly(dimethylacrylamide) (PS-b-PDMA) were previously synthesized and cast into films via these techniques. While irregular pore distributions were observed for linear polystyrene films generated by every technique screened, increasing the architectural complexity of the polymer yielded more regular films for a broad range of casting conditions for each of the techniques. With the exception of linear polystyrene, the airflow casting technique was shown to be the only technique capable of generating regular porous films for all of the polymeric materials.     

Synthesis of novel random and block copolymers of tert-butyldimethylsilyl methacrylate and methyl methacrylate by RAFT polymerization

Hydrophobic-hydrolysable copolymers consisting of methyl methacrylate (MMA) and tert-butyldimethylsilyl methacrylate (TBDMSMA) have been synthesized for the first time by Reversible Addition-Fragmentation chain Transfer (RAFT) polymerization technique using cumyl dithiobenzoate (CDB) and cyanoisopropyl dithiobenzoate (CPDB) as chain transfer agents (CTAs). The monomer reactivity ratios for TBDMSMA (r₁ = 1.40 ± 0.03) and MMA (r₂ = 1.08 ± 0.03) have been determined using a non-linear least-squares fitting method. Well-defined random copolymers PMMA-co-PTBDMSMA have been prepared. Then, the versatility of the RAFT process to synthesize silylated block copolymers with controlled molecular weights and low polydispersities has been demonstrated using two strategies: the synthesis of PMMA-SC(S)Ph or PTBDMSMA-SC(S)Ph as macro-chain transfer agent (macro-CTA) for use in a two step method or an one-pot method which consists in the successive addition of the two monomers. Diblock copolymers with narrow molecular weight distributions (PDI < 1.2) were obtained from the one-pot method with number-average molecular weight values within the range 10,000-22,000 g mol⁻¹.     

Synthesis of thermoresponsive block and graft copolymers via the combination of living cationic polymerization and RAFT polymerization using a vinyl ether-type RAFT agent

A novel vinyl ether-type RAFT agent, benzyl 2-(vinyloxy)ethyl carbonotrithioate (BVCT) was synthesized for various block copolymers via the combination of living cationic polymerization of vinyl ethers and reversible addition−fragmentation chain transfer (RAFT) polymerization. The novel BVCT–trifluoroacetic acid adduct play an important role to produce well-defined block copolymers, which is both as a cationogen under EtAlCl₂ initiation system in the presence of ethyl acetate for living cationic polymerization and a RAFT agent for blocks by RAFT polymerization. The resulting polymer, poly(vinyl ether)s, by living cationic polymerization had a high number average α-end functionality (≥0.9) as determined by both ¹H NMR and MALDI-TOF-MS spectrometry. In addition, this poly(vinyl ether)s worked well as a macromolecular chain transfer agent for RAFT polymerization. The RAFT polymerization of radically polymerizable monomers was conducted in toluene using 2,2′-azobis(isobutyronitrile) at 70 °C. For example, a double thermoresponsive block copolymer (MOVE₆₁-b-NIPAM₁₅₀) consisting of 2-methoxyethyl vinyl ether (MOVE) and N-isopropylacrylamide (NIPAM) was prepared via the combination of living cationic polymerization and RAFT polymerization. The block copolymer reversibly formed and deformed micellar assemblies above the phase separation temperature (T_ps) of poly(NIPAM) block in water. This BVCT is not only functioned as an initiator, but also acted as a monomer. When BVCT was copolymerized with MOVE by living cationic polymerization, followed by graft copolymerization with NIPAM via RAFT polymerization, well-defined graft copolymers (MOVE_n-co-BVCT_m)-g-NIPAM_x (n = 62–73, m = 1–9, x = 19–214) were successfully obtained. However, no micelle formed in water above T_ps of poly(NIPAM) graft chain unlike the case of block copolymers.     

基于RAFT聚合策略合成功能化聚烯烃嵌段聚合物的研究进展

首先介绍了可逆加成-断裂链转移聚合（RAFT）的聚合机理及其常用的RAFT试剂,并与其它两种活性可控自由基聚合[氮氧化合物媒介的自由基聚合（NMP）和原子转移自由基聚合（ATRP）]进行了简单的优缺点对比。其次,介绍了近些年在基于RAFT聚合制备功能化聚烯烃嵌段聚合物研究中取得的进展,重点综述了制备功能化聚烯烃嵌段聚合物时所采用的6种方法,包括①烯烃配位聚合与RAFT聚合相结合;②阴离子聚合与RAFT聚合相结合;③阳离子聚合与RAFT聚合相结合;④Click反应与RAFT聚合相结合;⑤开环聚合与RAFT聚合相结合;⑥叶立德活性聚合与RAFT聚合相结合。最后,对基于RAFT聚合策略设计合成功能化聚烯烃嵌段聚合物的研究前景与实际应用进行了展望。     

Synthesis of POSS-containing fluorosilicone block copolymers via RAFT polymerization for application as non-wetting coating materials

By using a polydimethylsiloxane (PDMS) macro-chain transfer agent with trithiocarbonate groups at both ends, fluorosilicone block copolymers containing polyhedral oligomeric silsesquioxane (POSS) were synthesized via reversible addition–fragmentation chain transfer (RAFT) polymerization. Acryloisobutyl POSS (APOSS) and 2,2,3,4,4,4-hexafluorobutyl acrylate (HFBA) were sequentially introduced into the copolymers. The obtained triblock copolymers PDMS-b-(PAPOSS)₂ exhibited a low polydispersity index (PDI) of less than 1.42 in the first 6 h of polymerization, but the PDI value became broader later because of the steric hindrance of the POSS macromer. The POSS-containing fluorosilicone pentablock copolymers with a PDI of about 2.0, which were prepared by the further RAFT polymerization of HFBA, showed clear microphase separation. The average roughness values of the copolymer films were enhanced by introducing POSS, and a certain POSS content led to a significant decrease of the receding contact angle. Measurements of water contact angles and ice shear strengths demonstrated that the non-wetting properties of the copolymer films were improved by the incorporation of both POSS and fluorine blocks. The block copolymers combine the advantages of POSS, PDMS and fluoropolymers, and can be potentially applied as non-wetting coating materials for anti-icing or anti-frosting.