Effect of polymerization conditions on the syndiotactic-specificity in radical polymerization of N-isopropylacrylamide and fractionation of the obtained polymer according to the stereoregularity

Radical polymerization of N-isopropylacrylamide (NIPAAm) was examined in the presence of hexamethylphosphoramide (HMPA). The addition of an excess amount of HMPA induced syndiotactic-specificity that gradually enhanced as the feed monomer was consumed. The syndiotacticity of the obtained poly(NIPAAm)s was improved by increasing the [HMPA]₀/[NIPAAm]₀ ratio to five and prolonging the polymerization time to 96 h (racemo=72%). It was also revealed that more stereoregulated poly(NIPAAm) could be fractionated by reprecipitating the resulting polymers from hexane-THF mixture. This result suggested that more stereoregulated poly(NIPAAm) showed a lower solubility than less stereoregulated poly(NIPAAm)s. Furthermore, unusual hysteresis was observed in transmittance analysis of an aqueous solution of the fractionated syndiotactic poly(NIPAAm).     

Direct synthesis of syndiotactic-rich poly(N-isopropylacrylamide) via radical polymerization of hydrogen-bond-complexed monomer

Radical polymerization of N-isopropylacrylamide (NIPAAm) in toluene was investigated in the presence of hexamethylphosphoramide (HMPA). We succeeded in directly preparing syndiotactic-rich poly(NIPAAm), the syndiotacticity of which (r=70%) is the highest among those of radically-prepared poly(NIPAAm)s so far reported, by lowering polymerization temperature to −60 °C in the presence of a two-fold amount of HMPA. The NMR analysis revealed that the induced syndiotactic-specificity was ascribed to 1:1 complex formation between NIPAAm and HMPA. Furthermore, thermodynamic analysis described that the induced syndiotactic-specificity was enthalpically achieved.     

Effect of a combination of hexamethylphosphoramide and alkyl alcohol on the stereospecificity of radical polymerization of N-isopropylacrylamide

Radical polymerization of N-isopropylacrylamide (NIPAAm) was investigated at low temperatures in the presence of both hexamethylphosphoramide (HMPA) and alkyl alcohols. Although HMPA and alkyl alcohols separately induced syndiotactic specificity in NIPAAm polymerization in toluene at low temperatures, a combination of HMPA and less bulky alkyl alcohols, such as methanol and ethanol, was found to induce isotactic specificity at −80 °C. NMR analysis of mixtures of NIPAAm, ethanol and HMPA suggested the formation of a 1:1:1 complex through O-H•••O=C and N-H•••O=P hydrogen bonding. It is believed that the steric effect of HMPA enhanced by cooperative hydrogen bonding was responsible for the combined effect of HMPA and alkyl alcohols in inducing isotactic specificity.     

Hydrogen-bond-assisted isotactic-specific radical polymerization of N-isopropylacrylamide with pyridine N-oxide

Radical polymerization of N-isopropylacrylamide (NIPAAm) in CHCl₃ at low temperatures in the presence of pyridine N-oxide (PNO) was investigated. An isotactic poly(NIPAAm) with meso diad content of 61% was successfully prepared at −60 °C in the presence of a two-fold amount of PNO. Thermodynamic analysis suggested that the isotactic-specificity was entropically induced, probably due to conformational fixation near the propagating chain-end through coordination by PNO.     

Hydrogen-bond-assisted stereocontrol in the radical polymerization of N-isopropylacrylamide with bidentate Lewis base

Radical polymerization of N-isopropylacrylamide (NIPAAm) in toluene was investigated in the presence of bidentate Lewis base such as diphosphonates. Isotacticity of the obtained poly(NIPAAm)s slightly increased at −80 °C, whereas syndiotactic-rich poly(NIPAAm)s were obtained at −40-0 °C. This result corresponded to the results observed in the presence of primary alkyl phosphates. NMR analysis revealed that NIPAAm monomer and tetraisopropyl methylenebisphosphonate formed mono-binding hydrogen-bond-assisted complex at 0 °C, but a chelate complex at −80 °C. Thus, it was concluded that the stereospecificity in NIPAAm polymerization strongly depended on the complexation mode of the added bidentate Lewis base.     

Metal-free isotactic-specific radical polymerization of N-alkylacrylamides with 3,5-dimethylpyridine N-oxide: The effect of the N-substituent and solvent on the isotactic specificity

Radical polymerization of N-methylacrylamide (NMAAm), N-n-propylacrylamide, N-isopropylacrylamide (NIPAAm) and N-benzylacrylamide was investigated in CHCl₃, CH₂Cl₂ and CH₃CN, in the presence of 3,5-dimethylpyridine N-oxide (35DMPNO) to examine the effects of the N-substituent and the solvent on the isotactic specificity induced by 35DMPNO. With addition of 35DMPNO to radical polymerization of N-alkylacrylamides in CHCl₃, isotactic specificity was significantly induced in NIPAAm polymerization but only slightly induced in NMAAm polymerization. Furthermore, mixed solvents of CH₃CN and halomethanes such as CHCl₃ and CH₂Cl₂ enhanced the ability of 35DMPNO to induce isotactic specificity, and poly(NIPAAm) with 74% meso dyad was obtained.     

Thermoresponsive surface prepared by atom transfer radical polymerization directly from poly(vinylidene fluoride) for control of cell adhesion and detachment

Thermoresponsive surface was prepared from commercial poly(vinylidene fluoride) (PVDF) films via surface‐initiated atom transfer radical polymerization. The direct initiation of the secondary fluorinated site of PVDF facilitated grafting of the N‐isopropylacrylamide (NIPAAm) monomer. The PVDF surfaces grafted with poly(N‐isopropylacrylamide) [P(NIPAAm)] were characterized by X‐ray photoelectron spectroscopy. Kinetics study revealed that the P(NIPAAm) chain growth from the PVDF surface was consistent with a “controlled” process. The temperature‐dependent swelling behavior of the surfaces in aqueous solution was studied by atomic force microscope. At 37°C [above the lower critical solution temperature (LCST, about 32°C) of NIPAAm], the seeded cells adhered and spread on the NIPAAm grafted PVDF surface. Below the LCST, the cells detached from the P(NIPAAm)‐grafted PVDF surface spontaneously. The thermoresponsive surfaces are potentially useful as stimuli‐responsive adhesion modifiers in the biomedical fields.© 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

A study of hydrogel thermal-dynamics using Fourier transform infrared spectrometer

A rapid and reliable method was presented for studying hydrogel dynamics/kinetics. Two temperature-sensitive hydrogels, poly-N-isopropylacrylamide (poly(NIPAAm)) and the copolymer of N,N-diethylacrylamide and sodium methacrylate (molar ratio=97:3, poly(NDEAAm-co-MAA)) were synthesized. The thermal-behaviors of the gels were studied through the absorbance intensities of both swollen water and gel frame components, and the peak positions of amide band along heating/cooling pathways under dynamic Fourier transform infrared (FTIR) probing. The results showed that the lower critical solution temperature (LCST) of poly(NIPAAm) is about 33-35 °C, which is consistent with reported value of ∼34 °C. Compared to poly(NIPAAm), poly(NDEAAm-co-MAA) has relatively continuous volume phase transition, starting at ∼35 °C and a better thermal-reversibility with similar swelling and deswelling profiles over a larger temperature range (10-80 °C for poly(NDEAAm-co-MAA) vs. 10-33 °C for poly(NIPAAm)). The H-bonding water along phase transition was also studied, showing a less reversibility of poly(NIPAAm) compared to poly(NDEAAm-co-MAA). In addition, FTIR spectrometer was also used to study the volume changes of poly(NDEAAm-co-MAA) under variations in environmental salinity.     

pH and temperature responsive porous membranes via an in situ bulk copolymerization approach

In the present study, an in situ approach to pH and temperature responsive membranes is developed. The membrane matrix is formed through bulk polymerization and crosslinking of liquid monomer 2-hydroxyethyl methacrylate (HEMA) while the membrane pores are formed by the templating of inorganic particles. The functional monomers methacrylic acid (MAA) and N-isopropylacrylamide (NIPAAm) are incorporated into membrane casting solution in order to confer membranes with pH and temperature responsive properties. The poly(HEMA/MAA) membranes exhibit a reversible pH-dependent water flux, while the poly(HEMA/NIPAAm) membranes exhibit a reversible temperature-dependent water flux. The flux of the poly(HEMA/MAA) membrane increased by 70% when pH was decreased from 10.0 to 2.0, while the flux poly(HEMA/NIPAAm) membrane increased by 150% when temperature was increased from 20 to 45 °C. The protein adsorption and antifouling performance of the poly(HEMA/MAA) and poly(HEMA/NIPAAm) membranes also exhibit pH and temperature responsive properties.     

Synthesis and characterization of biresponsive graft copolymer gels

Graft copolymer gels with different compositions were prepared by the radical polymerization of N-isopropylacrylamide (NIPAAm) and poly(2-vinylpyridine) (P2VP) macromonomers in dioxane with 1 mol% N,N′-methylenebisacrylamide (BIS) as the crosslinking agent. The graft copolymer gels were analyzed at different temperatures and pH values. They demonstrated the typical swelling behavior for poly(N-isopropylacrylamide) (PNIPAAm) gels with changing temperature. In addition to the temperature dependent measurements, the graft copolymer with a high P2VP content showed a pronounced swelling transition with changing pH value. By separating the temperature and the pH sensitive component, it was possible to obtain a gel which could be swelled independently in response to temperature and pH.     

Thermo‐ and pH‐responsive behaviors of graft copolymer and blend based on chitosan and N‐isopropylacrylamide

Thermo‐ and pH‐sensitive polymers were prepared by graft polymerization or blending of chitosan and poly(N‐isopropylacrylamide) (PNIPAAm). The graft copolymer and blend were characterized by Fourier transform‐infrared, thermogravimetric analysis, X‐ray diffraction measurements, and solubility test. The maximum grafting (%) of chitosan‐g‐(N‐isopropylacrylamide) (NIPAAm) was obtained at the 0.5 M NIPAAm monomer concentration, 2 × 10⁻³ M of ceric ammonium nitrate initiator and 2 h of reaction time at 25°C. The percentage of grafting (%) and the efficiency of grafting (%) gradually increased with the concentration of NIPAAm up to 0.5 M, and then decreased at above 0.5 M NIPAAm concentration due to the increase in the homopolymerization of NIPAAm. Both crosslinked chitosan‐g‐NIPAAm and chitosan/PNIPAAm blend reached an equilibrium state within 30 min. The equilibrium water content of all IPN samples dropped sharply at pH > 6 and temperature > 30°C. In the buffer solutions of various pH and temperature, the chitosan/PNIPAAm blend IPN has a somewhat higher swelling than that of the chitosan‐g‐NIPAAm IPN. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 78: 1381–1391, 2000     

Synthesis and characterization of polyrotaxanes comprising α-cyclodextrins and poly(ε-caprolactone) end-capped with poly(N-isopropylacrylamide)s

Biodegradable polyrotaxane (PR)-based triblock copolymers were synthesized via the atom transfer radical polymerization (ATRP) of N-isopropylacrylamide (NIPAAm) initiated with polypseudorotaxanes (PPRs) consisting of a distal 2-bromopropiomyl bromide end-capping poly(ε-caprolactone) (Br-PCL-Br) and a varying amount of α-cyclodextrins (α-CDs) in the presence of Cu(I)Br/PMDETA at 25 °C in aqueous solution. The copolymers were featured by relatively higher yields from 46.0% to 82.8% as compared with previous reports. Their structure was characterized in detail by using ¹H NMR, ¹³C CP/MAS NMR, GPC, WXRD, DSC and TGA analyses. When a feed molar ratio of NIPAAm to Br-PCL-Br was changed from 50 to 200, the degree of polymerization of PNIPAAm blocks attached to two ends of PPRs was in a range of 158–500. About one third of the added α-CDs were still entrapped on the central PCL chain after the ATRP process. Attaching PNIPAAm rendered the copolymers soluble in aqueous solution showing the thermo-responsibility as evidenced by turbidity measurements.     

Synthesis and characterization of a novel unsaturated polyester based on poly(trimethylene terephthalate)

Unsaturated aromatic polyesters were obtained by glycolysis of poly(trimethylene terephthalate) with cis-2-buten-1,4-diol followed by a solid-state polymerization. The glycolysis was performed in a batch mode as well as through a continuous process in a twin screw extruder. The degradation and subsequent rebuilding of the polymer chain during the course of reaction was followed by means of inherent and melt viscosity measurements, and ¹H NMR terminal group analysis of the intermediates and the final products. Structural investigations revealed that this new approach resulted in melt processible unsaturated polyesters with cross-linkable sites having similar characteristics to that of the virgin saturated polyester. Although the processing temperature for the different reaction steps was sufficiently high (180−260 °C), no thermally induced cross-linking of the incorporated unsaturated bonds could be evidenced indicating that the obtained products remained stable during the production stage. For comparison purposes, a commercial unsaturated polyester (Vestodur^©) was included in the investigations. UV irradiation of thin polyester films did not result in cross-linked products but in cis-trans isomerization of the incorporated bisoxybutenyl unit.     

Synthesis of NIPAAm-based polymer-grafted silica beads by surface-initiated ATRP using Me4Cyclam ligands and the thermo-responsive behaviors for lanthanide(III) ions

The applicability of atom transfer radical polymerization (ATRP) to the copolymerization of N-isopropylacrylamide (NIPAAm) with N-vinyl-2-pyrrolidone (NVP) was examined in CuCl/CuCl₂-catalyst system using tris[2-(dimethylamino)ethyl]amine (Me₆TREN) and 1,4,8,11-tetramethyl-1,4,8,11-tetraazacyclotetradecane (Me₄Cyclam) as ligands. In the Me₆TREN system, less reactive NVP not only does not quantitatively copolymerize but also interferes with homopolymerization of NIPAAm units. In contrast, the Me₄Cyclam system under heating was more active, although the controllability for polymer homogeneity is lower than Me₆TREN system. The application of active Me₄Cyclam system to surface-initiated ATRP has successfully prepared silica beads surface-modified with NIPAAm copolymers of NVP and 4-vinylpyridine (VPy). The thermo-responsive behavior of surface-grafted NIPAAm-based polymers was investigated for lanthanide trivalent ions (Ln(III)) in different pH solutions. In the weak acidic solutions of pH = 5.4–5.6, all the surface-grafted polymers including poly(NIPAAm) exhibited only adsorption behavior with regular selectivity (Eu³⁺ > Sm³⁺ > Nd³⁺ > Ce³⁺ > La³⁺) below the phase-transition temperatures. In the more acidic solution of pH = 2.9, the surface-grafted poly(NIPAAm) and NVP copolymers exhibited adsorption and desorption behaviors below and above the phase-transition temperatures, while VPy copolymers exhibited only adsorption independent of temperature change. Furthermore, the adsorption capacity of all the surface-grafted polymers was deteriorated by the lowering of pH. The observed desorption and the deterioration of adsorption capacity suggest the weakening of adsorption strength for Ln(III) in low pH solutions. In this study, a possible adsorption/desorption mechanism of Ln(III) on surface-grafted NIPAAm-based polymers is discussed.     

Convenient synthesis of poly(2,6-dihydroxy-1,5-naphthylene) by Cu(II)-amine catalyzed oxidative coupling polymerization

A convenient synthesis of regiocontrolled poly(2,6-dihydroxy-1,5-naphthylene) (PDHN) with high molecular weights by oxidative coupling polymerization of 2,6-dihydroxynaphthalene (2,6-DHN) has been developed. Polymerizations were conducted in 2-methoxyethanol in the presence of di-μ-hydroxo-bis[(N,N,N′,N′-tetramethylethylenediamine)copper (II)] chloride (CuCl(OH)TMEDA) as the catalyst under air at 25 °C. To determine the optimum conditions, the effects of the amounts of the catalysts and the solvents were investigated. In the presence of 5 mol% of the catalyst to the monomer in 2-methoxyethanol, polymerization proceeded smoothly, giving PDHN with a number average molecular weight (M_n) of 52,000. PDHN was converted to poly(2,6-dibutoxy-1,5-naphthylene) (PDBN) to improve the solubility. The structure of PDBN was characterized by ¹H and ¹³C NMR spectroscopy and was estimated to consist completely of the 1,5-linkage. The average refractive indices (n_AV) of the PDHN and PDBN films were 1.6003 and 1.5815, respectively, and the dielectric constants (ε) estimated from the refractive indices were 2.82 and 2.75, respectively.     

Synthesis and characterization of biodegradable polylactides and polylactide-block-poly(Z-lysine) copolymers

The reaction of (R,R)-trans-1,2-bis(2,4,6-triisopropylbenzenesulfonamidato)cyclohexane (^RRTBSC-H₂, 1) with MN[Si(CH₃)₃] in tetrahydrofuran (THF) produces [(^RRTBSC)₂M₄(THF)₄] (2: M = Li, 3: M = Na, 4: M = K). Experimental results show that all three complexes 2-4 are active toward the ring-opening polymerization of l-lactide and compound 2 efficiently catalyzes the polymerization of l-lactide in the presence of a variety of alcohols in a controlled fashion with very narrow polydispersity index. In addition, a variety of biodegradable poly(l-lactide)-block-poly(N_ξ-carbobenzyloxy-l-lysine) block copolymers with different ratios have also been synthesized using poly(l-lactide) containing amino chain end (PLLA-NH₂) as a macroinitiator.     

Highly crosslinked poly(glycidyl methacrylate-co-divinyl benzene) particles by precipitation polymerization

Stable and smooth surface poly(glycidyl metharylate-co-divinylbenzene) (GMA-co-DVB) microspheres composed of various concentrations of DVB from 20 to 90 mol% in acetonitrile medium were prepared without a significant coagulum by precipitation polymerization. The number-average diameter of the microspheres linearly increases from 2.63 to 3.34 μm and the particle size distribution becomes narrower by decreasing the uniformity from 1.10 to 1.02 with the DVB concentration from 20 to 90 mol%. The yield of polymerization increased from 28.9 to 79.7% with the DVB concentration as well. The FT-IR spectrum shows the characteristic peaks at 1725-1650 cm⁻¹ assigned to the confirmation of the polymerization between GMA and DVB. No glass transition temperature and the onset of the thermal degradation temperature at higher temperature indicate that the poly(GMA-co-DVB) is crosslinked; this is evidenced by the swelling ratio measurement relevant to the crosslinking density of the poly(GMA-co-DVB). The swelling test suggested that the poly(GMA-co-DVB) particles would be a core/shell type structure composing of a highly crosslinked DVB rich-phase in the core part and slightly crosslinked GMA rich-phase in the shell part.     

Monodisperse temperature-responsive hollow polymer microspheres: Synthesis, characterization and biological application

Temperature-responsive hollow poly(N-isopropylacrylamide) (PNIPAAm) microspheres were prepared by a two-stage distillation precipitation polymerization to afford a core-shell microspheres with subsequent removal of poly(methacrylic acid) (PMAA) core. PMAA@PNIPAAm core-shell microspheres were synthesized by the second-stage polymerization of NIPAAm in the presence of PMAA as core with N,N′-methylenebisacrylamide as crosslinker in acetonitrile, in which the hydrogen-bonding interaction between the carboxylic acid group of PMAA core and the amide group of NIPAAm as well as MBAAm played a key role to form the core-shell microspheres. The hollow PNIPAAm microspheres with different thicknesses, which were controlled by the monomer loading level and the crosslinking degree, were developed after the removal of PMAA core. The loading and controlled-release behavior of the drug on the hollow PNIPAAm microspheres was investigated with doxorubicin hydrochloride. The core-shell and hollow microspheres were characterized with transmission electron microscopy, scanning electron microscopy, dynamic light scattering, static light scattering, X-ray photoelectron spectroscopy, elemental analysis, and FT-IR spectra.     

Preparation of heterotactic-rich poly(methyl methacrylate) with narrow molecular weight distribution bytert-butyllithium/bis(2,6-di-tert-butylphenoxy)methylaluminum

Summary Polymerization of methyl methacrylate (MMA) withtert-butyllithium (t-C₄H₉Li) in toluene in the presence of aluminum alkoxides such as ethoxide,tert-butoxide and 2,6-di-tert-butylphenoxide, were examined at various Al/Li ratios. In the cases of ethoxide andtert-butoxide, predominantly isotactic polymers with broad molecular weight distribution were obtained. Combinations oft-C₄H₉Li and bis(2,6-ditert-butylphenoxy)methylaluminum [MeAl(ODBP)₂] were found to be an efficient initiating system for heterotactic polymerization of MMA, which gives PMMA rich in heterotactic triads up to 68% with narrow molecular weight distribution (Mw/Mn=1.09–1.17). End group analysis by¹H NMR indicated thatt-C₄H₉Li initiates the polymerization and MeAl(ODBP)₂ works as a stereospecific modifier. From stereosequence analysis of the heterotactic PMMA by¹³C NMR, it was found that the calculated pentad fractions from the first-order Markovian statistics (Pm/r=0.742, Pr/m=0.627) fitted the observed ones better than those from Bernoullian statistics. The glass transition temperature of the heterotactic PMMA was 13°C lower than that of syndiotactic PMMA, and the intrinsic viscosity in tetrahydrofuran was close to that of isotactic PMMA with a similar molecular weight but higher than that of syndiotactic PMMA.     

Synthesis and characterization of graft copolymers with poly(epichlorohydrin-co-ethylene oxide) as backbone by combination of ring-opening polymerization with living anionic polymerization

Series of graft copolymers with [Poly(epichlorohydrin-co-ethylene oxide)] [Poly(ECH-co-EO)] as backbone and polystyrene (PS), poly(isoprene) (PI) or their block copolymers as side chains were successfully synthesized by combination of ring-opening polymerization (ROP) with living anionic polymerization. The Poly(ECH-co-EO) with high molecular weight (M_n = 3.3 × 10⁴ g/mol) and low polydispersity index (PDI = 1.34) was firstly synthesized by ring-ROP using ethylene glycol potassium as initiator and triisobutylaluminium (i-Bu₃Al) as activator. Subsequently, by “grafting onto” strategy, the graft copolymers Poly(ECH-co-EO)-g-PI, Poly(ECH-co-EO)-g-PS and Poly(ECH-co-EO)-g-(PI-b-PS) were obtained using the coupling reaction between living PI⁻Li⁺, PS⁻Li⁺ or PS-b-PI⁻Li⁺ species capped with or without 1,1-diphenylethylene (DPE) agent and chloromethyl groups on poly(ECH-co-EO). By model experiment, the addition of DPE agent was confirmed to have an important effect on the grafting efficiency at room temperature. Finally, the target graft copolymers and intermediates were characterized by SEC, ¹H NMR, MALLS and FTIR in detail, and thermal behaviours of the graft copolymers were also investigated by DSC measurement.