Optical and electrical properties of ZnO films prepared by URT-IP method

Optical and electrical properties were studied on thin polycrystalline ZnO films (200-nm thick) deposited on glass substrates at 200 °C by a DC-arc ion plating method (URamoto-Tanaka-type ion plating method). Effects of the oxygen flow rate (OFR) on film properties were examined. The resistivity of undoped films changed from 4.2×10⁻³ to 9.6×10⁻¹ Ω cm, corresponding to the carrier concentration of 1.0×10²⁰-1.2×10¹⁸ cm⁻³, depending on the increase in OFR from 0 to 40 sccm. The Hall mobility tends to be the maximum value of 28 cm² (V s)⁻¹ at OFR of 10 sccm. Photoluminescence (PL) spectra exhibited a dominant near-band-edge (NBE) emission together with weak PL bands at 2.2 and 3.2 eV. Intensity of NBE was maximum at OFR of 10 sccm. Intensity of the PL band at 2.2 eV increased with increase in OFR. As a result of Ga-doping, the resistivity decreased and the carrier concentration increased by one order of magnitude. The optical transmittance was more than 90% in 400-1200 nm. The ZnO:Ga (3 and 4 wt.% Ga-doped) thin films with the lowest resistivity of 2.6×10⁻⁴ Ω cm, the highest mobility of 25 cm² (V s)⁻¹, and the highest PL intensity were obtained at OFR of 10 sccm. Further increase of OFR led to the decrease in both mobility and PL intensity.     

Low resistivity transparent conducting CdO thin films deposited by DC reactive magnetron sputtering at room temperature

Transparent conducting cadmium oxide (CdO) films were deposited on PET (polyethylene terephthalate) substrate by DC reactive magnetron sputtering at room temperature. All the films deposited at room temperature were polycrystalline in rock-salt structure. Dependences of the physical properties of the CdO films on the oxygen partial pressure were systematically studied. The films deposited at low oxygen flow rate were (200) oriented, while the films deposited at an oxygen flow rate greater than 20 sccm were (111) oriented. The average grain size of the CdO films decreased as the oxygen flow rate increases as determined by XRD and SEM. The Hall effect measurement showed that CdO films have high concentration, low resistivity, and high mobility. Both the mobility and the concentration of the carrier decreased with the increase of the oxygen flow rate. A minimum sheet resistance of 36.1 Ω/□, or a lowest resistivity of 5.44 × 10^− 4 Ω cm (6.21 × 10²⁰/cm³, μ = 19.2 cm²/Vs) was obtained for films deposited at an oxygen flow rate of 10 sccm.     

Effects of growth variables on the properties of single crystalline ZnO thin film grown by inductively coupled plasma metal organic chemical vapor deposition

Single crystalline undoped and Ga-doped n-type zinc oxide (ZnO) films were grown on sapphire (Al₂O₃) substrates by inductively coupled plasma (ICP) metal organic chemical vapor deposition. Effects of growth variables on the structural, optical, and electrical properties of ZnO films have been studied in detail. Single crystal films with flat and smooth surfaces were reproducibly obtained, with application of sample bias and O₂ ICP. The best film properties were obtained at the growth condition of 650 °C, 400 W ICP power, − 94 V bias voltage, O/Zn (VI/II) ratio of 75. Single crystalline Ga doped n-ZnO films were also obtained, with free carrier concentration of about 1.5 × 10¹⁹/cm³ at 1 at.% Ga concentration.     

Optical and ferromagnetic characteristics of Mn doped ZnO thin films grown by filtered cathodic vacuum arc technique

Mn doped ZnO (ZnO:Mn) thin films with ~ 10 at.% of Mn were grown on quartz substrates by filtered cathodic vacuum arc (FCVA) technique at low substrate temperature (≤ 200 °C). The influence of substrate temperature and oxygen flow rate on the optical, electrical and magnetic properties of the ZnO:Mn thin films was studied. Both room temperature ferromagnetism and ultraviolet photoluminescence were observed in all films. A maximum saturation moment of 2.9 × 10⁻²⁴ A m²/Mn can be achieved for the films grown in an optimum condition. This suggests that the fabrication of high-quality ZnO:Mn films by FCVA technique has the potential to realize efficient magneto-optic devices operating at ultraviolet regime.     

Effect of the oxygen flow on the properties of ITO thin films deposited by ion beam assisted deposition (IBAD)

ITO films were deposited onto glass substrates by ion beam assisted deposition method. The oxygen ions were produced using a Kaufman ion source. The oxygen flow was varied from 20 until 60 sccm and the effect of the oxygen flow on properties of ITO films has been studied. The structural properties of the film were characterized by X-ray diffraction and atomic force microscopy. The optical properties were characterized by optical transmission measurements and the optical constants (refractive index n and extinction coefficient k) and film thickness have been obtained by fitting the transmittance using a semi-quantum model. The electrical properties were characterized by Hall effect measurements. It has been found that the ITO film with low electrical resistivity and high transmittance can be obtained with 40 sccm oxygen flow (the working pressure is about 2.3 × 10^− 2 Pa at this oxygen flow).     

Deposition of zirconium oxynitride films by reactive cathodic arc evaporation and investigation of physical properties

The area of metal oxynitrides is poorly explored, and understanding of the fundamental mechanism that explains structural, mechanical, electrical, and optical properties is still insufficient. Therefore, the purpose of the present investigation is to analyze structural, electrical, and optical properties of ZrN_xO_y films deposited by reactive cathodic arc evaporation.Depending on the oxygen flow, cubic ZrN:O, monoclinic ZrO₂:N, and tetragonal ZrO₂:N phases films were prepared. The sheet resistance and the optical transmittance very much depend on the oxygen flow. Optical transparent ZrN_xO_y films with transmittance of 86% at 650 nm, the sheet resistance 1.1 · 10³ Ω/sq, and the figure of merit 2 · 10^− 4 Ω^− 1 are deposited with the 60 sccm oxygen flow.     

Al-doped ZnO thin films deposited by reactive frequency magnetron sputtering: H2-induced property changes

Al-doped ZnO (AZO) transparent conductive thin films have been prepared by radio-frequency magnetron sputtering with a ceramic target (98 wt.% ZnO, 2 wt.% Al₂O₃) in different Ar + H₂ ambient at a substrate temperature of 200 °C. To investigate the influence of H₂-flow on the properties of AZO films, H₂-flow was changed during the growth process with a fixed Ar-flow of 60 sccm. The results indicate that H₂-flow has a considerable influence on the transparent conductive properties of AZO films. The low resistivity in the order of 10^− 4 Ω cm and the high average transmittance more than 92% in the visible range were obtained for the samples prepared in the optimal H₂-flow range from 0.4 sccm to 1.0 sccm. In addition, the influence of H₂-flow on the structure and composition of AZO films have also been studied.     

Advantages of using amorphous indium zinc oxide films for window layer in Cu(In,Ga)Se2 solar cells

The advantages of using indium zinc oxide (IZO) films instead of conventional Ga-doped zinc oxide (ZnO:Ga) films for Cu(In,Ga)Se₂ (CIGS) solar cells are described. The electrical properties of IZO are independent of film thickness. IZO films have higher mobility (30-40 cm²/Vs) and lower resistivity (4-5 × 10^− 4 Ω cm) compared to ZnO:Ga films deposited without intentional heating, because the number of grain boundaries in amorphous IZO films is small. The properties of a CIGS solar cell using IZO at the window layer were better than those obtained using a conventional ZnO:Ga at the window layer; moreover, the properties tended to be independent of thickness. These results indicate that use of IZO as a transparent conducting oxide layer is expected to increase the efficiency of CIGS solar cells.     

Nitrogen-doped p-type ZnO thin films and ZnO/ZnSe p-n heterojunctions grown on ZnSe substrate by radical beam gettering epitaxy

We investigate the p-type doping in ZnO prepared by the method of radical beam gettering epitaxy using NO gas as the oxygen source and nitrogen dopant. Secondary ion mass spectroscopy measurements demonstrate that N is incorporated into ZnO film in concentration of about 8 × 10¹⁸ cm^− 3. The hole concentration of the N-doped p-type ZnO films was between 1.4 × 10¹⁷ and 7.2 × 10¹⁷ cm^− 3, and the hole mobility was 0.9-1.2 cm²/Vs as demonstrated by Hall effect measurements. The emission peak of 3.312 eV is observed in the photoluminescence spectra at 4.2  of N-doped p-type ZnO films, probably neutral acceptor bound. The activation energy of the nitrogen acceptor was obtained by temperature-dependent Hall-effect measurement and equals about 145 meV. The p-n heterojunctions ZnO/ZnSe were grown on n-type ZnSe substrate and have a turn-on voltage of about 3.5 V.     

Carrier transport in polycrystalline transparent conductive oxides: A comparative study of zinc oxide and indium oxide

Highly doped indium-tin oxide films exhibit resistivities ρ as low as  1.2 × 10^− 4 Ω cm, while for ZnO films resistivities in the range of 2 to 4 × 10^− 4 Ω cm are reported. This difference is unexpected, if ionized impurity scattering would be dominant for carrier concentrations above 10²⁰ cm^− 3. By comparing the dependences of the effective Hall mobility on the carrier concentration of ZnO and ITO it is found that grain barriers limit the carrier mobility in ZnO for carrier concentrations as high as 2 × 10²⁰ cm^− 3, independently, if the films were grown on amorphous or single crystalline substrates. Depending on the deposition method, grain barrier trap densities between 10¹² and 3 × 10¹³ cm^− 2 were estimated for ZnO layers. Also, crystallographic defects seem to reduce the mobility for highly doped ZnO films. On the other hand, for ITO films such an influence of the grain barriers was not observed down to carrier concentrations of about 10¹⁸ cm^− 3. Thus the grain barrier trap densities of ZnO and ITO are significantly different, which seems to be connected with the defect chemistry of the two oxides and especially with the piezoelectricity of zinc oxide.     

Substrate temperature dependence of the properties of Ga-doped ZnO films deposited by DC reactive magnetron sputtering

Ga-doped zinc oxide (ZnO:Ga) transparent conductive films were deposited on glass substrates by DC reactive magnetron sputtering. The influence of substrate temperature on the structural, electrical, and optical properties of ZnO:Ga films was investigated. The X-ray diffraction (XRD) studies show that higher temperature helps to promote Ga substitution more easily. The film deposited at 350 °C has the optimal crystal quality. The morphology of the films is strongly related to the substrate temperature. The film deposited is dense and flat with a columnar structure in the cross-section morphology. The transmittance of the ZnO:Ga thin films is over 90%. The lowest resistivity of the ZnO:Ga film is 4.48×10⁻⁴ Ω cm, for a film which was deposited at the substrate temperature of 300 °C.     

Transparent conductive ZnO:B films deposited by magnetron sputtering

This paper focuses on the preparation of boron doped ZnO (ZnO:B) films prepared by nonreactive mid-frequency magnetron sputtering from ceramic target with 2 wt.% doping source. Adjusting power density, ZnO:B film with low resistivity (1.54 × 10^− 3 Ω cm) and high transparency (average transparency from 400 to 1100 nm over 85%) was obtained. Different deposition conditions were introduced as substrate fixed in the target center and hydrogen mediation. Hall mobility increased from 11 to above 26 cm²/V·s, while carrier concentration maintained almost the same, leading to low resistivity of 6.45 × 10^− 4 Ω cm. Transmission spectra of ZnO:B films grown at various growth conditions were determined using a UV-visible-NIR spectrophotometer. An obvious blue-shift of absorption edge was obtained while transmittances between 600 nm and 1100 nm remained almost the same. Optical band baps extracted from transmission spectra showed irregular enhancement due to the Burstein-Moss effect and band gap renormalization. Photoluminescence spectra also showed a gradual increase at UV emission peak due to free exciton transition near band gap. We contributed this enhancement in both optical band gap and UV photoluminescence emission to the lattice structure quality melioration.     

Thermally stable, highly conductive, and transparent Ga-doped ZnO thin films

Highly conductive and transparent films of Ga-doped ZnO (GZO) have been prepared by pulsed laser deposition using a ZnO target with Ga₂O₃ dopant of 3 wt.% in content added. Films with resistivity as low as 3.3 × 10^− 4 Ω cm and transmittance above 80% at the wavelength between 400 and 800 nm can be produced on glass substrate at room temperature. It is shown that a stable resistivity for use in oxidation ambient at high temperature can be attained for the films. The electrical and optical properties, as well as the thermal stability of resistivity, of GZO films were comparable to those of undoped ZnO films.     

Deposition of Na–N dual acceptor doped p-type ZnO thin films and fabrication of p-ZnO:(Na,N)/n-ZnO:Eu homojunction

Sodium and nitrogen dual acceptor doped p-type ZnO (ZnO:(Na, N)) films have been prepared by spray pyrolysis technique at a substrate temperature of 623 K. The ZnO:(Na, N) films are grown at a fixed N doping concentration of 2 at.% and varying the nominal Na doping concentration from 0 to 8 at.%. The XRD results show that all the ZnO:(Na, N) films exhibited (0 0 2) preferential orientation. The EDX and elemental mapping analysis shows the presence and distribution of Zn, O, Na and N in the deposited films. The Hall measurement results demonstrate that the Na–N dual acceptor doped ZnO films show excellent p-type conduction. The p-type ZnO:(Na, N) films with comparatively low resistivity of 5.60 × 10⁻² Ω cm and relatively high carrier concentration of 3.15 × 10¹⁸ cm⁻³ are obtained at 6 at.%. ZnO based homojunction is fabricated by depositing n-type layer (Eu doped ZnO) grown over the p-type layer ZnO:(Na, N). The current–voltage (I–V) characteristics measured from the two-layer structure show typical rectifying characteristics of p-n junction with a low turn on voltage of about 1.69 V. The ZnO:(Na, N) films exhibit a high transmittance (about >90%) and the average reflectance is 8.9% in the visible region. PL measurement shows near-band-edge (NBE) emission and deep-level (DL) emission in the ZnO:(Na, N) thin films.     

CuIn1 − xGaxSe2 photovoltaic devices for tandem solar cell application

CuIn_1 − xGa_xSe₂ (CIGS) solar cells show a good spectral response in a wide range of the solar spectrum and the bandgap of CIGS can be adjusted from 1.0 eV to 1.7 eV by increasing the gallium-to-indium ratio of the absorber. While the bandgaps of Ga-rich CIGS or CGS devices make them suitable for top or intermediate cells, the In rich CIGS or CIS devices are well suited to be used as bottom cells in tandem solar cells. The photocurrent can be adapted to the desired value for current matching in tandem cells by changing the composition of CIGS which influences the absorption characteristics. Therefore, CIGS layers with different [Ga]/[In + Ga] ratios were grown on Mo and ZnO:Al coated glass substrates. The grain size, composition of the layers, and morphology strongly depend on the Ga content. Layers with Ga rich composition exhibit smaller grain size and poor photovoltaic performance. The current densities of CIGS solar cells on ZnO:Al/glass varied from 29 mA cm^− 2 to 13 mA cm^− 2 depending on the Ga content, and 13.5% efficient cells were achieved using a low temperature process (450 °C). However, Ga-rich solar cells exhibit lower transmission than dye sensitized solar cells (DSC). Prospects of tandem solar cells combining a DSC with CIGS are presented.     

Effect of deposition distance and temperature on electrical, optical and structural properties of radio-frequency magnetron-sputtered gallium-doped zinc oxide

Films of gallium-doped zinc oxide (GZO) were deposited on glass substrates by radio-frequency magnetron sputtering using a ceramic target of Ga:ZnO (4 at.% Ga vs. Zn). Both the substrate temperature (T_s) and the target-substrate distance (d_ts) were varied and the effect on electrical, optical and structural properties of the resulting films were measured. The highest conductivity of 3200 S/cm was obtained at a deposition temperature of 250 °C, at a d_ts of 51 mm. This sample had the highest carrier concentration in this study, 9.6 × 10²⁰/cm³. Optical transmittance of all films was <90% in the visible range. The grain size of the film grown at d_ts = 51 mm was smaller than the grain size for films grown with a shorter d_ts; moreover, the films with d_ts = 51 mm exhibited the smoothest surface, with a root mean square surface roughness of 2.7 nm. Changes in T_s have a more pronounced effect on conductivity compared to changes in d_ts; however, variations in structure do not appear to be well-correlated with conductivity for samples in the 2000-3200 S/cm range. These results suggest that incorporation and activation of Ga is of key importance when attempting to obtain GZO films with conductivities greater than 2000 S/cm.     

Preparation of wide gap Cu(In,Ga)S2 films on ZnO coated substrates

We have prepared Cu(In,Ga)S₂ films at growth temperatures from 300 °C to 580 °C with a homogeneous gallium depth distribution (estimated band gap 1.67 eV) onto soda lime glass (SLG) substrates with one of three different kinds of back contact: Mo(1000 nm), ZnO(500 nm), and Mo(30 nm)/ZnO(500 nm), respectively. We have also investigated the depth profiles of Zn and Na (diffused from SLG) in Cu(In,Ga)S₂ films by secondary ion mass spectroscopy (SIMS). The efficiency of solar cells on Mo increases with increasing growth temperature. It is higher on Mo/ZnO than on ZnO, and increases from 350 °C to 450 °C, then decreases above 450 °C. It was observed by SIMS that the amount of Zn in Cu(In,Ga)S₂ on Mo/ZnO is lower than it is on ZnO up to 450 °C, and a large amount of Zn diffuses into absorbers over 450 °C, which contributes to decreasing efficiency. The amount of Na in the back contact increases with growth temperature. The depth distribution of Na in Cu(In,Ga)S₂ films on Mo is almost constant in the order of 10¹⁷-10¹⁸ cm^− 3, on ZnO and Mo/ZnO the Na concentration increases towards the surface and is in the range of 10¹⁵-10¹⁷ cm^− 3.     

Annealing effect on dielectric and leakage current characteristics of Mn-doped Ba0.6Sr0.4TiO3 thin films as gate insulators for low voltage ZnO thin film transistor

We report on the dielectric properties and leakage current characteristics of 3 mol% Mn-doped Ba_0.6Sr_0.4TiO₃ (BST) thin films post-annealed up to 600 °C following room temperature deposition. The suitability of 3 mol% Mn-doped BST films as gate insulators for low voltage ZnO thin film transistors (TFTs) is investigated. The dielectric constant of 3 mol% Mn-doped BST films increased from 24 at in-situ deposition up to 260 at an annealing temperature of 600 °C due to increased crystallinity and the formation of perovskite phase. The measured leakage current density of 3 mol% Mn-doped BST films remained on the order of 5 × 10^− 9 to 10^− 8 A/cm² without further reduction as the annealing temperature increased, thereby demonstrating significant improvement in the leakage current characteristics of in-situ grown Mn-doped BST films as compared to that (5 × 10^− 4 A/cm² at 5 V) of pure BST films. All room temperature processed ZnO-TFTs using a 3 mol% Mn-doped BST gate insulator exhibited a field effect mobility of 1.0 cm²/Vs and low voltage device performance of less than 7 V.     

Electrical and optical properties of Al-doped ZnO films deposited by hollow cathode gas flow sputtering

Al-doped ZnO (AZO) films were deposited on glass by hollow cathode gas flow sputtering using Zn-Al alloy targets. Sputtering power for all the depositions was fixed at 1500 W. Resistivities of 0.81-1.1 × 10^− 3 Ω cm were obtained for AZO films deposited at room temperature with an O₂ flow from 38 to 50 standard cubic centimetre/minute (SCCM), while static deposition rates were almost constant at 270-300 nm/min. On the other hand, lower resistivities of 5.2-6.4 × 10^− 4 Ω cm were obtained for AZO films deposited at 200 °C with an O₂ flow from 25 to 50 SCCM, while the static deposition rates were almost constant at 200-220 nm/min. Average transmittances in the visible light region were above 80% for both sets of films.     

Characterization of MgZnO films grown by plasma enhanced metal-organic chemical vapor deposition

MgZnO (magnesium-zinc-oxide) films were grown on (11-20) sapphire substrates and Zn-polar ZnO substrates by plasma enhanced metal-organic chemical vapor deposition (PE-MOCVD) employing microwave-excited plasma. Structural, electrical and optical properties were investigated by X-ray diffraction, atomic force microscope, Hall, transmittance and photoluminescence measurement. The c-axis lattice constant decreases proportionally to an increase in the Mg content of Mg_xZn_1 − xO films. Therefore, this indicates that Mg atoms can be substituted in the Zn sites. Mg contents in films on ZnO substrates increase up to 0.11. In addition, Ga doped ZnO films were grown on (11-20) sapphire substrates. The resistivity of the films on (11-20) sapphire is controlled between 1.2 × 10^− 3 Ω cm to 1 Ω cm by changing the process conditions. The overall results indicate the promising potential of this PE-MOCVD method for related (Zn, Mg)O films formation because of the reactivity of the radicals, such as oxygen radicals (O?).