应力对Ag颗粒增强SnCu基复合钎料蠕变性能的影响

使用搭接面积为1mm2的单搭接钎焊接头,研究了恒定温度下应力对Ag颗粒增强SnCu基复合钎料钎焊接头蠕变寿命的影响,结果表明:Ag颗粒增强SnCu基复合钎料的蠕变抗力优于99.3Sn0.7Cu基体钎料;随着应力的增大,复合钎料及其基体钎料钎焊接头的蠕变寿命均呈下降趋势,且应力对复合钎料钎焊接头蠕变寿命的影响比基体钎料明显.     

温度对Cu颗粒增强复合钎料蠕变性能的影响

蠕变性能是影响钎焊接头可靠性的重要指标之一.采用搭接面积为1 mm2的单搭接钎焊接头,在恒定载荷下,测定了Cu颗粒增强锡铅基复合钎料钎焊接头的蠕变寿命,分析并讨论了温度对该复合钎料蠕变寿命的影响.结果表明:Cu颗粒增强的锡铅基复合钎料的蠕变抗力优于传统63Sn37Pb共晶钎料;钎焊接头蠕变寿命随温度的升高而降低,并且温度对复合钎料钎焊接头蠕变寿命的影响较传统63Sn37Pb钎料明显.     

Ag颗粒含量对SnCu基复合钎料性能的影响

利用颗粒增强原理研制了新型Ag颗粒增强SnCu基复合钎料,研究了Ag颗粒不同含量对复合钎料性能影响.结果表明:当Ag含量(体积分数)为5%时,复合钎料铺展面积最大,润湿角最小,钎焊接头蠕变寿命最长,比基体钎料提高23倍.     

纳米结构强化无铅焊点的力学性能

新型的无铅钎料不仅要具备含铅钎料的工艺性能,更重要的是要有更高的力学性能,特别是焊接接头的抗蠕变能力。将纳米级多面齐聚倍半硅氧烷(Polyhedral oligomeric silsesquioxanes,POSS)颗粒作为增强相添加到基体钎料中,能够有效地改善Sn-3. 5Ag基复合钎料的性能。研究了不同种类POSS增强颗粒对Sn-3. 5Ag钎料显微组织和力学性能的影响,确定出POSS增强颗粒复合钎料的最佳配比,并对最佳配比复合钎料在不同温度不同载荷条件下的蠕变寿命进行了研究。结果表明：POSS颗粒质量分数小于2%时,可以抑制基板界面处初晶金属间化合物的生长;复合钎料的抗剪切强度明显提高;低温时,最大蠕变寿命明显改善。     

新型纳米结构颗粒增强无铅复合钎料性能

为了解决传统复合钎料制备中强化颗粒容易粗化的问题,提高无铅复合钎料的性能,选用共晶Sn-3.5Ag、Sn-3.0Ag-0.5Cu钎料作为基体,3种不同类型具有纳米结构的有机-无机笼型硅氧烷齐聚物(POSS) 颗粒作为增强相而制成复合钎料。研究了复合钎料的铺展性能、钎焊接头的力学性能和抗蠕变性能。结果表明,复合钎料的润湿性能均优于基体钎料的润湿性能,复合钎料钎焊接头的剪切强度和蠕变断裂寿命均明显提高。在相同条件下,Sn-Ag-Cu基复合钎料钎焊接头的性能优于Sn-Ag基复合钎料钎焊接头。      

SiC陶瓷与Ti合金的(Ag-Cu-Ti) -W复合钎焊接头组织结构研究

研究了在Ag,Cu,Ti粉末中加入W粉连接钛合金和SiC陶瓷的接头组织结构和接头状况.结果表明W颗粒均匀分布在钎缝的Ag相中,且未与Ag-Cu-Ti合金基体发生冶金反应,W颗粒的大小和形状基本上与加入前的粉末相当.在较低的钎焊温度和较短的钎焊时间下,能形成组织结构均匀、连接良好的复合接头,钎缝内Cu-Ti相较少,钎缝与钛合金界面形成了多层Ti含量呈梯度变化的Cu-Ti扩散反应层组成的扩散带.W的加入降低了接头热应力.而较高的钎焊温度和较长的钎焊时间,容易在近缝区的陶瓷中产生裂纹.由于扩散进入钎缝Ti量的增多,使得钎缝内形成很多长条形CuTi相组织,提高了与钎缝相邻的Cu-Ti扩散反应层的Ti浓度,并且钎缝内钛合金界面附近形成了没有W相的带状区域.     

耐高温瞬时液相连接无铅钎焊接头的时效稳定性

通过瞬时液相(TLP)连接的互连工艺,采用Sn4.7Ag1.7Cu+Ag复合钎料,制备Sn4.7Ag1.7Cu+Ag复合钎料/Cu接头.采用SEM观察恒温时效过程中接头的组织,结合EDS对比不同工艺下试样接头组织,并对接头性能进行对比分析.结果表明:随着Ag颗粒含量的增加,Sn4.7Ag1.7Cu+Ag/Cu接头耐高温(300℃)服役性能随之提高;Ag含量为25％(质量分数)时接头在高于基体钎料熔点(217℃)83℃下服役15天未断裂,且抗拉强度为25.74 MPa,达到了低温焊接、高温服役的目的;与Sn4.7Ag1.7Cu/Cu接头相比,随着时效的进行,Sn4.7Ag1.7Cu+Ag复合钎料/Cu接头焊缝组织中残余的Ag颗粒不断溶解,并在接头界面附近产生大量Ag3 Sn化合物,而大量的块状Ag3 Sn化合物可以有效抑制焊缝中Sn元素向Cu基板扩散,达到抑制Cu3 Sn层生长的目的;在200℃服役温度条件下,随着时效的进行,Sn4.7Ag1.7Cu+Ag复合钎料/Cu接头力学性能先下降后上升,然后再下降并趋于稳定,且力学性能稳定性比Sn4.7Ag1.7Cu/Cu接头要好.     

高体积比SiCp/6063Al复合材料的铝基钎料制备及钎焊工艺研究

采用快速甩带技术制备了(Al-10Si-20Cu-0.05Ce)-1Ti(质量分数/％)急冷箔状钎料,并对60％体积分数的SiCp/6063Al复合材料进行真空钎焊实验,然后对钎料及接头的显微组织与性能进行测定和分析.结果表明,急冷钎料的微观组织细小、成分均匀,厚80～90μm,主要包含Al、CuAl2、Si和Al2Ti等相.当升高钎焊温度(T/℃)或延长保温时间(t/min),SiCp/钎料界面的润湿性改善,6063Al基体/钎料间互扩散和溶解作用增强,接头连接质量逐渐提高.当T=590℃、t=30 min时,接头抗剪强度达到112.6MPa;当T=590℃、t=50 min时,少量小尺寸SiCp因液态钎料排挤而分散于钎缝,因加工硬化而使接头强度递增7.3％.然而,当T≥595℃、t≥60 min时,SiCp偏聚于钎缝,导致接头组织恶化,且剪切断裂以脆性断裂为主.综合考虑钎焊成本与接头强度使用要求,确定最佳钎焊工艺为590℃、30 min.     

等温时效对新型Sn-Ag基复合钎料显微组织和力学性能的影响

研究了等温时效对Sn-3.5Ag共晶钎料及其复合钎料的力学性能和显微组织变化的影响。为了弥补传统复合钎料制备和服役中强化颗粒容易粗化的问题, 制备了不同种类最佳配比的具有纳米结构的有机无机笼型硅氧烷齐聚物(POSS)颗粒增强的Sn-Ag基复合钎料。对钎焊接头在不同温度（125、150、175℃）下进行时效,通过SEM和EDAX分析了钎料与基板间金属间化合物层(IMC)的生长情况。结果表明, 经过不同温度时效,复合钎料钎焊接头界面处金属间化合物的生长速率比Sn3.5Ag共晶钎料慢, 复合钎料的IMC生长的激活能分别为80、97和77kJ/mol,均高于Sn3.5Ag共晶钎料。经过150℃时效1000h后,复合钎料钎焊接头的剪切强度分别下降了22%、13%和18%,下降幅度相当或明显小于Sn-3.5Ag钎料钎焊接头。      

电子束钎焊接头组织分析

采用自主开发的电子束钎焊系统,对不锈钢毛细管板结构进行钎焊,通过电子探针显微分析仪研究了不同电子束钎焊规范下BNi-2钎料与管壁基体界面合金元素的分布,分析了钎料和界面区各相的化学组成.研究表明:在加速电压60kV,束流6.5 mA,加热时间37 s,扫描幅值O.5的电子束钎焊规范下,管板接头质量满足技术规范要求;随着电子束输入功率或功率密度增大,钎料和管壁的相互扩散作用增强,导致过渡层厚度增加,毛细管壁显著减薄;母材和钎料中合金元素的相互扩散导致过渡层的形成,过渡层主要由硼化铬、硼化镍和镍的固溶体组成.     

Creep property of composite solders reinforced by nano-sized particles

In the present work the creep properties of Sn37Pb and Sn0.7Cu based composite solders with nano-sized metallic Cu, Ag and nano-sized oxide Al₂O₃, TiO₂ reinforcement particles have been studied. First, a series of volume percentages of reinforcements were selected for optimizing the content of particles. Then, the composite solder with optimum volume fraction of the reinforcement particles, corresponding to maximum creep rupture life, is selected for investigating the effect of applied stress level and test temperature on creep rupture life of the composite solder joints. In the creep rupture life test, small single-lap tensile-shear joints were adopted. The results indicate that all the composite solders have improved creep resistance, comparing to the eutectic Sn37Pb solder and the Sn0.7Cu lead-free solder. The creep rupture life of the composite solder joints is first increased with the increase in the volume fraction of reinforcement in the composite solders. Then, the creep rupture life is decreased, as the reinforcement content exceeds a certain value. The creep rupture life of the solder joints is decreased with the increase of applied stress and testing temperature. Moreover, the reinforced efficiency of nano-sized Ag particles is the best in all the tested nano-sized reinforcements for the Sn37Pb based and Sn0.7Cu based composite solders, when the particles contents are in their own optimum content.     

Study on creep characterization of nano-sized Ag particle-reinforced Sn–Pb composte solder joints

In the present work, the creep strain of solder joints is measured using a stepped load creep test on a single specimen. Based on the experimental results, the constitutive model on the steady-state creep strain is established by applying a linear curve fitting for the nano-sized Ag particle-reinforced Sn37Pb based composite solder joint and the Sn37Pb solder joint, respectively. It is indicated that the activation energy of the Ag particle-reinforced Sn37Pb based composite solder joints is higher than that of Sn37Pb solder joints. It is expected that the creep resistance of the Ag particle-reinforced Sn37Pb based composite solder joints is superior to that of Sn37Pb solder.     

Creep behavior in Cu and Ag particle-reinforced composite and eutectic Sn-3.5Ag and Sn-4.0Ag-0.5Cu non-composite solder joints

Creep properties were determined for small, geometrically realistic Pb-free solder joints. Solder joints were prepared with eutectic Sn-3.5Ag and Sn-4.0Ag-0.5Cu solder alloys. Composite solder joints were made using the eutectic Sn-3.5Ag alloy as the matrix with 15 vol % of mechanically added 6 m size Cu and 4 m size Ag reinforcing particles. Creep tests were conducted on these joints at 25 °C, 65 °C and 105 °C representing homologous temperatures ranging from 0.61 to 0.78. Qualitative and quantitative evaluations of creep behavior were obtained from the distortion of excimer laser-induced surface ablation markings on the solder joint. Various creep parameters, such as global and localized creep strain, variation of creep strain and strain-rate, activation energy for creep, and the onset of tertiary creep were determined. General findings in this study revealed that the creep resistance in composite solder joints is significantly improved with Cu particle reinforcements. In contrast, the improvement in the creep properties of Ag particle-reinforced composite solder joints was far less even though highly uniform deformation in the joint was observed. The strain noted at the onset of tertiary creep for Cu and Ag reinforced composite solder joints was typically lower compared to non-composite solder joints. The activation energies for creep were similar for all the solder materials investigated in this study. © 2001 Kluwer Academic Publishers     

Effects of Ag particles content on properties of Sn0.7Cu solder

To improve properties of Sn0.7Cu solder, method of particles reinforced was employed. Effects of Ag particle contents (1, 3, 5, 7.5, and 10 vol.%) on spreadability, microstructure, shear strength and creep rupture life of Sn0.7Cu solders have been studied. The experimental results indicate that intermetallic compound (IMC) grows, Shear strength is increased and grains are fined with the increasing of Ag particles. When content of Ag particles is more than 5 vol.%, growth rate of IMC is increased significantly. When the content of Ag is 5 vol.%, the composite solder presents best spreadability and excellent creep rupture property which have maximum spreading area, minimum wetting angle and longest creep rupture life (about 22 times as long as that of Sn0.7Cu solder).     

Microstructural Evolution on the T91 Dissimilar Metal Joints during Creep Rupture Tests

T91 steel is one of the new materials presently employed in power plant pipe components. The creep rupture strength and microstructure of the T91+10CrMo910 and T91+13CrMo44 welded joints were analyzed during creep rupture tests. Creep transgranular ductile rupture occurred at the 10CrMo910 matrix in the T91+10CrMo910 welded joints and creep intergranular brittle rupture occurred at the 13CrMo44 HAZ in the T91+13CrMo44 joints. Microhardness measurements showed high hardness at the heat affected zone (HAZ) of T91 and a sharply drop at the 13CrMo44 HAZ during creep rupture. The metallographic tests showed that no obvious microstructure degradation was observed in the 10CrMo910 HAZ and matrix, while creep cracks appeared at the 13CrMo44 HAZ. T91 steel had relatively high creep resistant strength in the welded joints tested. Recovery occurred in the T91 HAZ with the growth of subgrain size and the decrease of dislocation density during creep. It was concluded that the dissimilar joints of T91 and low alloy h