首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 62 毫秒
1.
马广斌  朱正吼  夏小鸽 《材料导报》2006,20(Z2):196-197
采用高能球磨法制备了纳米Al2O3p/Cu复合材料粉体,复合粉体经过压制、烧结和挤压后成为铜复合材料,采用X射线衍射(XRD)、扫描电镜(SEM)、能谱仪(EDS)、电导仪等测试方法,研究了球磨后的复合粉体和复合材料显微结构、电导率和硬度.实验证明,粉体经过2h以上球磨后,Al2O3相逐渐消失,复合粉体为纳米晶结构,晶粒直径66~87nm.随着Al2O3粉体含量增加,铜复合材料的电导率显著下降.烧结后挤压有利于复合材料导电性能的提高.当Al2O3粉体含量1wt%、球磨6h时,烧结后重新挤压的复合材料试样电导率IACS 76%、硬度HB 83.8.  相似文献   

2.
《材料导报》2004,18(Z3)
设计并采用热压烧结的方法成功制备了TiCp/W和ZrCp/W两个系列碳化物颗粒增强钨基新型复合材料,并对其组织结构、室温力学性能及高温力学性能进行了系统研究.结果表明,复合材料体系的组元间有很好的热力学相容性和化学相容性;在异相界面处发生了W原子向TiC和ZrC晶格的扩散,分别形成了(Ti,W)C和(Zr,W)C固溶体,促进了两相界面结合和复合材料的致密化.碳化物颗粒的加入强烈阻碍了W晶粒的长大,并显著提高了复合材料的室温和高温力学性能.复合材料的抗弯强度和抗拉强度均随着试验温度的升高先增大后减小,在800~1400℃C时出现峰值,而抗压强度则随着温度的升高而单调下降.室温强化机制是细晶强化和第二相弥散强化,高温强化机理有:位错强化、细晶强化、界面强化及碳化物颗粒的弥散强化.  相似文献   

3.
TiCP/W及ZrCP/W复合材料的组织结构与性能   总被引:3,自引:0,他引:3  
周玉  王玉金  宋桂明 《材料导报》2004,18(8):97-101
设计并采用热压烧结的方法成功制备了TiCp/W和ZrCp/W两个系列碳化物颗粒增强钨基新型复合材料,并对其组织结构、室温力学性能及高温力学性能进行了系统研究.结果表明,复合材料体系的组元间有很好的热力学相容性和化学相容性;在异相界面处发生了W原子向TiC和ZrC晶格的扩散,分别形成了(Ti,W)C和(Zr,W)C固溶体,促进了两相界面结合和复合材料的致密化.碳化物颗粒的加入强烈阻碍了W晶粒的长大,并显著提高了复合材料的室温和高温力学性能.复合材料的抗弯强度和抗拉强度均随着试验温度的升高先增大后减小,在800~1400℃时出现峰值,而抗压强度则随着温度的升高而单调下降.室温强化机制是细晶强化和第二相弥散强化,高温强化机理有:位错强化、细晶强化、界面强化及碳化物颗粒的弥散强化.  相似文献   

4.
采用高能球磨法制备了不同质量分数碳纳米管(CNTs)与Al-5%Mg(质量分数)粉末的复合粉末,用热压烧结工艺制备了CNTs/Al-5%Mg复合材料。结果表明:高能球磨法可以将CNTs均匀的分散到基体中,并与其产生良好结合;CNTs具有细化复合粉末晶粒尺寸的作用,当CNTs含量为3%时,复合粉末的平均晶粒尺寸达到最小值为63.6nm,继续增加CNTs的含量,复合粉末平均晶粒尺寸增大;当CNTs含量为2%时,复合材料的抗拉强度和硬度达到最大值,与基体材料相比分别提高了42.39%和36.5%;CNTs/Al-5%Mg复合材料的强化机制为细晶强化和载荷传递。  相似文献   

5.
采用机械合金化-热压烧结法,制备TiC-CoCrFeNi复合材料,研究球磨时间对材料微观组织及力学性能的影响。结果表明:Co,Cr,Fe和Ni粉体在球磨10h后形成fcc结构的单相固溶体。经1200℃/1h热压烧结后,烧结体中生成TiC和Cr7C3结构的碳化物,并弥散分布于CoCrFeNi固溶体中。球磨时间显著改变了烧结体中碳化物的数量和尺寸,进而影响材料的力学性能。在球磨10h时,烧结体中纳米级TiC相急剧增多,此时复合材料的硬度(671HV)和屈服强度(1440MPa)达到最大值。  相似文献   

6.
本研究采用真空热压烧结技术, 在1600℃下制备了WC-TiC-TaC硬质合金材料, 研究了TiC含量对其微观组织及力学性能的影响。结果表明, 随着TiC含量的增多, 硬质合金材料的晶粒显著增大。当TiC的含量从10wt% 增加到25wt%时, 硬质合金材料的硬度逐渐增大, 最高可达19.81 GPa, 这是由于TiC的硬度高于基体WC的硬度; 与此同时, 硬质合金材料的抗弯强度和断裂韧度逐渐减小。当TiC的含量为10wt%时, 材料的抗弯强度有最大值, 其值为1147.24 MPa, 这是由于在材料内部形成了均匀、细小的晶粒组织; 在此含量下, 复合材料的增韧机理为细晶增韧、裂纹偏转、裂纹分支、裂纹桥接和韧窝增韧, 其断裂韧度有最大值, 为14.60 MPa·m1/2。  相似文献   

7.
为了细化TiC/Al基复合材料中的增强颗粒,进一步提高TiC颗粒对基体的强化效果,在锻铝6A02基体中加入适量Mo元素,用原位合成的方法制备TiC/Al基复合材料.对制备得到的铸态和轧制态材料进行了显微组织观察、拉伸和磨损实验.结果表明,TiC颗粒可以作为异质形核核心起到细化基体组织的作用.TiC颗粒的引入提高了材料在室温和高温的抗拉强度和屈服强度,同时改善了材料的耐磨损性能,且随着载荷的增加,耐磨性能的提高越明显.当加入质量分数1.0%的Mo时,可改善基体对TiC颗粒的润湿性,细化TiC颗粒的尺寸(0.5μm),使TiC颗粒分布更为均匀,材料的力学性能和磨损性能得到提高.然而,过高的Mo含量将导致在组织中出现粗大的脆性Al5Mo相,同时使材料的力学性能和磨损性能有所降低.  相似文献   

8.
采用原位合成法制备TiC/Al(7075)复合材料,研究原位TiC颗粒的存在形式、分布状态及不同原位TiC颗粒含量对TiC/Al(7075)复合材料的微观组织及力学性能的影响。结果显示,TiC颗粒多以近球形团聚态存在于7075铝基体中,颗粒团大小约为1μm。当原位TiC颗粒质量分数小于6%时,原位TiC颗粒分布较为均匀,随着颗粒含量的增加,TiC/Al(7075)复合材料的铸态组织由蔷薇状组织逐渐转变为等轴晶组织,晶粒尺寸也随着原位TiC颗粒含量的增加而减小。当原位TiC颗粒的质量分数大于6%时,组织中出现气孔。复合材料的硬度和抗冲击韧性测试表明,TiC/Al(7075)复合材料的硬度随TiC颗粒含量的增加而增加,最高硬度达HB 108,冲击韧性在颗粒质量分数为6%时达到最佳,较基体提升31.55%。  相似文献   

9.
采用高能球磨结合真空热压的手段制备了W-10%(质量分数)TiC复合材料。采用扫描电镜、透射电镜和x射线衍射等对复合粉体及复合材料进行表征。结果表明,通过高能球磨得到了粒径均匀,平均粒径约为100nm的纳米复合粉体,粉体经过1700℃真空热压烧结后致密度达到99.1%,并且保持细晶结构(平均晶粒尺寸为0.8gm)。热压和高能球磨导致的机械活化以及引入的Fe、Ni等杂质是复合材料低温烧结达到高致密度的重要原因。  相似文献   

10.
本研究采用真空热压烧结技术,在1600℃下制备了WC-TiC-TaC硬质合金材料,研究了TiC含量对其微观组织及力学性能的影响。结果表明,随着TiC含量的增多,硬质合金材料的晶粒显著增大。当TiC的含量从10wt%增加到25wt%时,硬质合金材料的硬度逐渐增大,最高可达19.81 GPa,这是由于TiC的硬度高于基体WC的硬度;与此同时,硬质合金材料的抗弯强度和断裂韧度逐渐减小。当TiC的含量为10wt%时,材料的抗弯强度有最大值,其值为1147.24 MPa,这是由于在材料内部形成了均匀、细小的晶粒组织;在此含量下,复合材料的增韧机理为细晶增韧、裂纹偏转、裂纹分支、裂纹桥接和韧窝增韧,其断裂韧度有最大值,为14.60 MPa·m~(1/2)。  相似文献   

11.
In this paper, we present a new method for inserting several triangulated surfaces into an existing tetrahedral mesh generated by the meccano method. The result is a conformal mesh where each inserted surface is approximated by a set of faces of the final tetrahedral mesh. First, the tetrahedral mesh is refined around the inserted surfaces to capture their geometric features. Second, each immersed surface is approximated by a set of faces from the tetrahedral mesh. Third, following a novel approach, the nodes of the approximated surfaces are mapped to the corresponding immersed surface. Fourth, we untangle and smooth the mesh by optimizing a regularized shape distortion measure for tetrahedral elements in which we move all the nodes of the mesh, restricting the movement of the edge and surface nodes along the corresponding entity they belong to. The refining process allows approximating the immersed surface for any initial meccano tetrahedral mesh. Moreover, the proposed projection method avoids computational expensive geometric projections. Finally, the applied simultaneous untangling and smoothing process delivers a high‐quality mesh and ensures that the immersed surfaces are interpolated. Several examples are presented to assess the properties of the proposed method.  相似文献   

12.
13.
Standards are the basis for production enterprises to organize production, ex-factory inspection, trade (delivery) and technical exchanges, product certification, quality arbitration and supervision.……  相似文献   

14.
A flow calorimeter for enthalpy increment measurements on condensed gases is presented. A better knowledge of the properties of the liquefied natural gas is needed, and therefore a liquid loop has been designed for our flow calorimeter. The fluid loop in the calorimeter is designed in order to avoid the two-phase region, since two phases would give compositional disturbances in the measurements. The avoidance of the two-phase region is made possible by increasing the pressure of the test fluid after the measurement section, then heating the fluid at super-critical pressure past the critical point. Finally, the fluid is throttled to the low-pressure gas state at the inlet condition of the compressor that circulates the fluid. To perform the pressure increase, a new cryogenic pump has been designed. To evaluate the new equipment, measurements were taken on liquid ethane over the temperature range 146–256 K at pressure between 0.9 and 5.1 MPa.  相似文献   

15.
On November 30, 2007, the China Association for Standardization (CAS) held a press conference at Beijing Diaoyutai State Guest House. Leaders from the China Household Electric Appliance Research Institute, the China Household Electric Appliance Association, and the China Consumers' Association attended and made speeches.……  相似文献   

16.
Zusammenfassung Bei der Gestaltung von Ernteprozessen — beispielsweise des Prozesses Mähdrusch, Körnertransport und -abnahme — als transportverbundene Fließarbeitsverfahren mit mindestens zwei verschiedenen Arbeitsmitteln gibt es einen großen Optimierungsspielraum. Solche Prozesse sind mehrstufige Bedienungsprozesse mit gemischter Anordnung der Bedienungseinrichtungen. Außerdem besitzen sie stark ausgeprägte räumliche Aspekte. Es wird vor allem gezeigt, welche Merkmale solcher Prozesse in Simulationsmodellen abgebildet sein müssen, welche Zielgrößen in Abhängigkeit von welchen Einflußgrößen unter Berücksichtigung welcher Prozeßbedingungen ermittelt werden sollten und wie der Bewertungsprozeß zur Ermittlung der gewünschten Informationen gestaltet werden muß.  相似文献   

17.
In the present study a high‐boron high speed steel (HSS) roll material was designed. Many expensive alloy elements have been substituted by cheap boron alloy, and high‐boron high speed steel roll has been manufactured by centrifugal casting method. The microstructures, mechanical properties and wear resistance of centrifugal casting high‐boron high speed steel roll have been investigated by optical microscopy (OM), scanning electron microscopy (SEM), and X‐ray diffraction (XRD) analysis, hardness test, impact test and wear test. The results indicated that the solidification microstructures of high‐boron high speed steel roll consisted of M2(B,C), (W,Mo)2(B,C), M3(B,C), M23(B,C)6 type borocarbides and martensite, a small amount of retained austenite. Borocarbides were continuously distributed over the grain boundary. After quenching from 1050 °C, local broken network appeared in partial borocarbides, and fine secondary borocarbide precipitated from the matrix. After tempering from 525 °C, the amount of precipitated borocarbide increased significantly. After heat treatment, the hardness of high‐boron high speed steel roll excelled 60 HRC, and its impact toughness excelled 8.0 J/cm2. The single groove steel rolling amount of high‐boron high speed steel rolls increases by 500% than that of bainite cast iron roll, when the rolls are used in K1 mill housing of bar mill.  相似文献   

18.
The definition of the thixotropy is a decrease in viscosity with time in shear and a subsequent recovery of viscosity after the shear deformation is removed.We ...  相似文献   

19.
Several researches have been reported about the characteristic of β-Ga2O3 nanowires which was synthesized on nickel oxide particle. But indeed, recent researches about synthesis of β-Ga2O3 nanowires on oxide-assisted transition metal are limited to nickel or cobalt oxide catalyst. In this work, Gallium oxide (β-Ga2O3 ) nanowires were synthesized by a simple thermal evaporation method from gallium powder in the range of 700 - 1000℃ using the iron, nickel, copper, cobalt and zinc oxide as a catalyst, respectively. The β-Ga2O3 nanowires with single crystalline without defects were successfully synthesized at the reaction temperature of 850, 900 and 950℃ in all the catalysts. But optimum experimental condition in synthesis of nanowires varied with the kind of catalyst. As increasing synthesis temperature,the morphology of gallium oxide nanowires changed from nanowires to nanorods, and its diameter increased. From these results, we could be proposed that the growth mechanism of β-Ga2O3 nanowires was changed with synthesis temperature of nanowires. Microstructure and morphology of Synthesized nanowire was characterized by HR-TEM, FE-SEM, EDX and XRD.  相似文献   

20.
正Responding to ISO’s appeal for survey for the to-be-developed ISO Strategy Plan for 2016-2020,SAC hosted a special workshop over the needs and comments of various fi elds on June 8 in Beijing.The workshop was attended by ISO President-elect and Ansteel General Manager Zhang Xiaogang,SAC Vice-Administrator Yu Xinli,and 30 experts from  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号