A functional 41-stage ring oscillator using scaled FinFET devices with 25-nm gate lengths and 10-nm fin widths applicable for the 45-nm CMOS node

In this letter, we have fabricated a functional FinFET ring oscillator with a physical gate length of 25 nm and a fin width of 10 nm, the smallest ever reported. We demonstrate that these narrow (W/sub fin/ = 10 nm) and tall (H/sub fin/ = 60 - 80 nm) fins can be reliably etched with controlled profiles and that they are required to keep the short-channel effects under control, resulting in drain-induced barrier leakage characteristics of 45 mV/V at V/sub dd/ = 1 V and L/sub g/ = 25 nm for the nFET. For these ultrathin (10 nm) fins, we have succeeded in properly setting the V/sub T/ at 0.2 V without the use of metal gates. In addition to ring oscillators, we also have obtained excellent pFET FinFET devices at wider fin widths (W/sub fin/ = 65 nm) with I/sub dsat/ = 380 /spl mu/A//spl mu/m at I/sub off/ = 60 nA//spl mu/m and V/sub dd/ = -1.2 V.     

Narrow-stripe distributed reflector lasers with first-order vertical grating and distributed Bragg reflectors

Narrow-stripe 1.55-/spl mu/m wavelength distributed reflector lasers consisting of both distributed Bragg reflectors and vertical grating of the first Bragg order were fabricated. A low threshold current I/sub th/ of 2.8 mA, a differential quantum efficiency /spl eta//sub d/ of 28% from the front facet, and a submode suppression ratio of 44 dB were obtained for structures with a stripe width of 1.3 /spl mu/m and a cavity length of 150 /spl mu/m.     

SODEL FET: novel channel and source/drain profile engineering schemes by selective Si epitaxial growth technology

In this paper, novel channel and source/drain profile engineering schemes are proposed for sub-50-nm bulk CMOS applications. This device, referred to as the silicon-on-depletion layer FET (SODEL FET), has the depletion layer beneath the channel region, which works as an insulator like a buried oxide in a silicon-on-insulator MOSFET. Thanks to this channel structure, junction capacitance (C/sub j/) has been reduced in SODEL FET, i.e., C/sub j/ (area) was /spl sim/0.73 fF//spl mu/m/sup 2/ both in SODEL nFET and pFET at Vbias =0.0 V. The body effect coefficient /spl gamma/ is also reduced to less than 0.02 V/sup 1/2/. Nevertheless, current drives of 886 /spl mu/A//spl mu/m (I/sub off/=15 nA//spl mu/m) in nFET and -320 /spl mu/A//spl mu/m (I/sub off/=10 nA//spl mu/m) in pFET have been achieved in 70-nm gate length SODEL CMOS with |V/sub dd/|=1.2 V. New circuit design schemes are also proposed for high-performance and low-power CMOS applications using the combination of SODEL FETs and bulk FETs on the same chip for 90-nm-node generation and beyond.     

A technique to improve the drive current of high-voltage I/O transistors in digital CMOS technologies

By combining a 0.12-/spl mu/m-long 1.2-V thin-oxide transistor with a 0.22-/spl mu/m-long 3.3-V thick-oxide transistor in a 0.13-/spl mu/m CMOS process, a composite MOS transistor structure with a drawn gate length of 0.34 /spl mu/m is realized. Measurements show that at V/sub GS/=1.2 V and V/sub DS/=3.3 V, the composite transistor has more than two times the drain current of the minimum channel length (0.34 /spl mu/m) 3.3-V thick-oxide transistor, while having the same breakdown voltage (V/sub BK/) as the thick-oxide transistor. Exploiting these, it should be possible to implement 3.3-V I/O transistors with better combination of drive current, threshold voltage (V/sub T/) and breakdown voltage in conventional CMOS technologies without adding any process modifications.     

Experimental evidence for nonlucky electron model effect in 0.15-/spl mu/m NMOSFETs

It is shown that in 0.15-/spl mu/m NMOSFETs the device lifetime under channel hot-carrier (CHC) stress is lower than that under drain avalanche hot-carrier (DAHC) stress and therefore the hot-carrier stress-induced device degradation in 0.15-/spl mu/m NMOSFETs cannot be explained in the framework of the lucky electron model (LEM). Our investigation suggests that such a "non-LEM effect" may be due to increased interface state generation by the movement of the maximum impact ionization site from the lightly doped drain (LDD) diffusion region to the boundary of the bulk and LDD region beneath the gate oxide. This paper provides experimental evidence for the non-LEM effect by comparing the degradation characteristics and the maximum impact ionization sites as a function of gate oxide thickness and gate length.     

Reliability investigation of 0.07-/spl mu/m InGaAs-InAlAs-InP HEMT MMICs with pseudomorphic In/sub 0.75/Ga/sub 0.25/As channel

The authors have investigated the reliability performance of G-band (183 GHz) monolithic microwave integrated circuit (MMIC) amplifiers fabricated using 0.07-/spl mu/m T-gate InGaAs-InAlAs-InP HEMTs with pseudomorphic In/sub 0.75/Ga/sub 0.25/As channel on 3-in wafers. Life test was performed at two temperatures (T/sub 1/ = 200 /spl deg/C and T/sub 2/ = 215 /spl deg/C), and the amplifiers were stressed at V/sub ds/ of 1 V and I/sub ds/ of 250 mA/mm in a N/sub 2/ ambient. The activation energy is as high as 1.7 eV, achieving a projected median-time-to-failure (MTTF) /spl ap/ 2 /spl times/ 10/sup 6/ h at a junction temperature of 125 /spl deg/C. MTTF was determined by 2-temperature constant current stress using /spl Delta/G/sub mp/ = -20% as the failure criteria. The difference of reliability performance between 0.07-/spl mu/m InGaAs-InAlAs-InP HEMT MMICs with pseudomorphic In/sub 0.75/Ga/sub 0.25/As channel and 0.1-/spl mu/m InGaAs-InAlAs-InP HEMT MMICs with In/sub 0.6/Ga/sub 0.4/As channel is also discussed. The achieved high-reliability result demonstrates a robust 0.07-/spl mu/m pseudomorphic InGaAs-InAlAs-InP HEMT MMICs production technology for G-band applications.     

Characterization of CMOS Devices for VLSI

CMOS bulk and SOS technologies are discussed for VLSI with emphasis on static and dynamic characteristics of two-input NAND gates. Olpthnum performance (minimum figure of merit FM= f/sub pd/P/sub d/) is obtained for a CMOS/SOS two-input NAND gate (FO = 2, C/sub L/ = 22 fF) with an electrical channel length L = 0.75 /spl mu/m, channel width W= 5.0 /spl mu/m, and oxide thickness X/sub O/ = 450 /spl Aring/with V/sub DD/ = 3.0 V, to yield t/sub pd/ = 400 ps and P/sub d/ = 250 /spl mu/W (t/sub pd/P/sub d/ = 100 fJ) at room temperature. Bulk technology performs within a factor of 2 of SOS for t/sub pd/ and P/sub d/. CMOS technologies offer subnanosecond propagation delays, similar to ECL bipolar, at the low submilliwatt power levels of CMOS. An analytical expression for t/sub pd/ describes the performance of two-input NAND gates in terms of device modeling and fabrication parameters. Such an expression provides a hierarchal modeling approach to characterize mini-cells for VLSI.     

2 V-operated InGaP-AlGaAs-InGaAs enhancement-mode pseudomorphic HEMT

A low-voltage single power supply enhancement-mode InGaP-AlGaAs-InGaAs pseudomorphic high-electron mobility transistor (PHEMT) is reported for the first time. The fabricated 0.5/spl times/160 /spl mu/m/sup 2/ device shows low knee voltage of 0.3 V, drain-source current (I/sub DS/) of 375 mA/mm and maximum transconductance of 550 mS/mm when drain-source voltage (V/sub DS/) was 2.5 V. High-frequency performance was also achieved; the cut-off frequency(F/sub t/) is 60 GHz and maximum oscillation frequency(F/sub max/) is 128 GHz. The noise figure of the 160-/spl mu/m gate width device at 17 GHz was measured to be 1.02 dB with 10.12 dB associated gain. The E-mode InGaP-AlGaAs-InGaAs PHEMT exhibits a high output power density of 453 mW/mm with a high linear gain of 30.5 dB at 2.4 GHz. The E-mode PHEMT can also achieve a high maximum power added efficiency (PAE) of 70%, when tuned for maximum PAE.     

Diamond FET using high-quality polycrystalline diamond with f/sub T/ of 45 GHz and f/sub max/ of 120 GHz

Using high-quality polycrystalline chemical-vapor-deposited diamond films with large grains (/spl sim/100 /spl mu/m), field effect transistors (FETs) with gate lengths of 0.1 /spl mu/m were fabricated. From the RF characteristics, the maximum transition frequency f/sub T/ and the maximum frequency of oscillation f/sub max/ were /spl sim/ 45 and /spl sim/ 120 GHz, respectively. The f/sub T/ and f/sub max/ values are much higher than the highest values for single-crystalline diamond FETs. The dc characteristics of the FET showed a drain-current density I/sub DS/ of 550 mA/mm at gate-source voltage V/sub GS/ of -3.5 V and a maximum transconductance g/sub m/ of 143 mS/mm at drain voltage V/sub DS/ of -8 V. These results indicate that the high-quality polycrystalline diamond film, whose maximum size is 4 in at present, is a most promising substrate for diamond electronic devices.     

The impact of uniform strain applied via bonding onto plastic substrate on MOSFET performance

For the first time, this letter presents a novel post-backend strain applying technique and the study of its impact on MOSFET device performance. By bonding the Si wafer after transistor fabrication onto a plastic substrate (a conventional packaging material FR-4), a biaxial-tensile strain (/spl sim/0.026%) was achieved globally and uniformly across the wafer due to the shrinkage of the bonded adhesive. A drain-current improvement (average /spl Delta/I/sub d//I/sub d//spl sim/10%) for n-MOSFETs uniformly across the 8-in wafer is observed, independent of the gate dimensions (L/sub g//spl sim/55 nm -0.530 /spl mu/m/W /spl sim/2-20 /spl mu/m). The p-MOSFETs also exhibited I/sub d/-improvement by /spl sim/7% under the same biaxial-tensile strain. The strain impact on overall device characteristics was also studied, including increased gate-induced drain leakage and short-channel effects.     

DC and RF characteristics of E-mode Ga/sub 0.51/In/sub 0.49/P-In/sub 0.15/Ga/sub 0.85/As pseudomorphic HEMTs

The DC and RF characteristics of Ga/sub 0.49/In/sub 0.51/P-In/sub 0.15/Ga/sub 0.85/As enhancement- mode pseudomorphic HEMTs (pHEMTs) are reported for the first time. The transistor has a gate length of 0.8 /spl mu/m and a gate width of 200 /spl mu/m. It is found that the device can be operated with gate voltage up to 1.6 V, which corresponds to a high drain-source current (I/sub DS/) of 340 mA/mm when the drain-source voltage (V/sub DS/) is 4.0 V. The measured maximum transconductance, current gain cut-off frequency, and maximum oscillation frequency are 255.2 mS/mm, 20.6 GHz, and 40 GHz, respectively. When this device is operated at 1.9 GHz under class-AB bias condition, a 14.7-dBm (148.6 mW/mm) saturated power with a power-added efficiency of 50% is achieved when the drain voltage is 3.5 V. The measured F/sub min/ is 0.74 dB under I/sub DS/=15 mA and V/sub DS/=2 V.     

High performance 35 nm gate length CMOS with NO oxynitride gate dielectric and Ni salicide

The 35 nm gate length CMOS devices with oxynitride gate dielectric and Ni salicide have been fabricated to study the feasibility of higher performance operation. Nitrogen concentration in gate oxynitride was optimized to reduce gate current I/sub g/ and to prevent boron penetration in the pFET. The thermal budget in the middle of the line (MOL) process was reduced enough to realize shallower junction depth in the S/D extension regions and to suppress gate poly-Si depletion. Finally, the current drives of 676 /spl mu/A//spl mu/m in nFET and 272 /spl mu/A//spl mu/m in pFET at V/sub dd/=0.85 V (at I/sub off/=100 nA//spl mu/m) were achieved and they are the best values for 35 nm gate length CMOS reported to date.     

High-speed scaled-down self-aligned SEG SiGe HBTs

A scaled-down self-aligned selective-epitaxial-growth (SEG) SiGe HBT, structurally optimized for an emitter scaled down toward 100 nm, was developed. This SiGe HBT features a funnel-shaped emitter electrode and a narrow separation between the emitter and base electrodes. The first feature is effective for suppressing the increase of the emitter resistance, while the second one reduces the base resistance of the scaled-down emitter. The good current-voltage performance - a current gain of 500 for the SiGe HBT with an emitter area of 0.11 /spl times/ 0.34 /spl mu/m and V/sub BE/ standard deviation of less than 0.8 mV for emitter width down to about 0.13 /spl mu/m - demonstrates the applicability of this SiGe HBT with a narrow emitter. This SiGe HBT demonstrated high-speed operation: an emitter-coupled logic (ECL) gate delay of 4.8 ps and a maximum operating frequency of 81 GHz for a static frequency divider.     

InGaAs-InP mesa DHBTs with simultaneously high f/sub /spl tau// and f/sub max/ and low C/sub cb//I/sub c/ ratio

We report an InP-InGaAs-InP double heterojunction bipolar transistor (DHBT), fabricated using a conventional triple mesa structure, exhibiting a 370-GHz f/sub /spl tau// and 459-GHz f/sub max/, which is to our knowledge the highest f/sub /spl tau// reported for a mesa InP DHBT-as well as the highest simultaneous f/sub /spl tau// and f/sub max/ for any mesa HBT. The collector semiconductor was undercut to reduce the base-collector capacitance, producing a C/sub cb//I/sub c/ ratio of 0.28 ps/V at V/sub cb/=0.5 V. The V/sub BR,CEO/ is 5.6 V and the devices fail thermally only at >18 mW//spl mu/m/sup 2/, allowing dc bias from J/sub e/=4.8 mA//spl mu/m/sup 2/ at V/sub ce/=3.9 V to J/sub e/=12.5 mA//spl mu/m/sup 2/ at V/sub ce/=1.5 V. The device employs a 30 nm carbon-doped InGaAs base with graded base doping, and an InGaAs-InAlAs superlattice grade in the base-collector junction that contributes to a total depleted collector thickness of 150 nm.     

Monolithically integrated InGaAs-AlGaInAs Mach-Zehnder Interferometer optical switch using quantum-well intermixing

A highly efficient monolithically integrated Mach-Zehnder interferometer (MZI) optical switch based on a 1.5-/spl mu/m InGaAs-AlGaInAs multiple-quantum-well structure is reported. The device was fabricated by integrating phase shifter sections with bandgap-shifted low-loss waveguides obtained by a single step sputtered SiO/sub 2/-annealing quantum-well intermixing technique. Evaluation of the refractive index change induced by current injection (plasma, band-filling, band-shrinkage effects) and applied electric field (quantum confined Stark effect) based on the MZI was investigated. A device with an active length of 400 /spl mu/m in one of the MZI arms had an extinction ratio /spl ges/20 dB with a half-wavelength current (I/sub /spl pi//) and half-wavelength voltage V/sub /spl pi// as low as 3.2 mA and 3.5 V (1.9 V in push-pull configuration), respectively.     

SOI technology for radio-frequency integrated-circuit applications

This paper presents a silicon-on-insulator (SOI) integration technology, including structures and processes of OFF-gate power nMOSFETs, conventional lightly doped drain (LDD) nMOSFETs, and spiral inductors for radio frequency integrated circuit (RFIC) applications. In order to improve the performance of these integrated devices, body contact under the source (to suppress floating-body effects) and salicide (to reduce series resistance) techniques were developed for transistors; additionally, locally thickened oxide (to suppress substrate coupling) and ultra-thick aluminum up to 6 /spl mu/m (to reduce spiral resistance) were also implemented for spiral inductors on high-resistivity SOI substrate. All these approaches are fully compatible with the conventional CMOS processes, demonstrating devices with excellent performance in this paper: 0.25-/spl mu/m gate-length offset-gate power nMOSFET with breakdown voltage (BV/sub DS/) /spl sim/ 22.0 V, cutoff frequency (f/sub T/)/spl sim/15.2 GHz, and maximal oscillation frequency (f/sub max/)/spl sim/8.7 GHz; 0.25-/spl mu/m gate-length LDD nMOSFET with saturation current (I/sub DS/)/spl sim/390 /spl mu/A//spl mu/m, saturation transconductance (g/sub m/)/spl sim/197 /spl mu/S//spl mu/m, cutoff frequency /spl sim/ 25.6 GHz, and maximal oscillation frequency /spl sim/ 31.4 GHz; 2/5/9/10-nH inductors with maximal quality factors (Q/sub max/) 16.3/13.1/8.95/8.59 and self-resonance frequencies (f/sub sr/) 17.2/17.7/6.5/5.8 GHz, respectively. These devices are potentially feasible for RFIC applications.     

Electrical characteristics of 8-/spl Aring/ EOT HfO/sub 2//TaN low thermal-budget n-channel FETs with solid-phase epitaxially regrown junctions

The authors demonstrate high-performing n-channel transistors with a HfO/sub 2//TaN gate stack and a low thermal-budget process using solid-phase epitaxial regrowth of the source and drain junctions. The thinnest devices have an equivalent oxide thickness (EOT) of 8 /spl Aring/, a leakage current of 1.5 A/cm/sup 2/ at V/sub G/=1 V, a peak mobility of 190 cm/sup 2//V/spl middot/s, and a drive-current of 815 /spl mu/A//spl mu/m at an off-state current of 0.1 /spl mu/A//spl mu/m for V/sub DD/=1.2 V. Identical gate stacks processed with a 1000-/spl deg/C spike anneal have a higher peak mobility at 275 cm/sup 2//V/spl middot/s, but a 5-/spl Aring/ higher EOT and a reduced drive current at 610 /spl mu/A//spl mu/m. The observed performance improvement for the low thermal-budget devices is shown to be mostly related to the lower EOT. The time-to-breakdown measurements indicate a maximum operating voltage of 1.6 V (1.2 V at 125 /spl deg/C) for a ten-year lifetime, whereas positive-bias temperature-instability measurements indicate a sufficient lifetime for operating voltages below 0.75 V.     

Analysis of the gate-source/drain capacitance behavior of a narrow-channel FD SOI NMOS device considering the 3-D fringing capacitances using 3-D simulation

This paper reports an analysis of the gate-source/drain capacitance behavior of a narrow-channel fully depleted (FD) silicon-on-insulator (SOI) NMOS device considering the three-dimensional (3-D) fringing capacitances. Based on the 3-D simulation results, when the width of the FD SOI NMOS device is scaled down to 0.05 /spl mu/m, the inner-sidewall-oxide fringing capacitance (C/sub FIS/), due to the fringing electric field at the edge of the mesa-isolated structure of the FD SOI NMOS device biased at V/sub G/=0.3 V and V/sub D/=1 V, is the second largest contributor to the gate-source capacitance (C/sub GS/). Thus, when using nanometer CMOS devices with a channel width smaller than 0.1 /spl mu/m, C/sub FIS/ cannot be overlooked for modeling gate-source/drain capacitance (C/sub GS//C/sub GD/).     

Demonstration of 1789 V, 6.68 m/spl Omega/ /spl middot/ cm/sup 2/ 4H-SiC merged-PiN-Schottky diodes

The design, fabrication and characterisation of a high performance 4H-SiC diode of 1789 V-6.6 A with a low differential specific-on resistance (R/sub SP/spl I.bar/ON/) of 6.68 m/spl Omega/ /spl middot/ cm/sup 2/, based on a 10.3 /spl mu/m 4H-SiC blocking layer doped to 6.6/spl times/10/sup 15/ cm/sup -3/, is reported. The corresponding figure-of-merit of V/sub B//sup 2//R/sub SP/spl I.bar/ON/ for this diode is 479 MW/cm/sup 2/, which substantially surpasses previous records for all other MPS diodes.     

A Micropower CMOS-Instrumentation Amplifier

A CMOS switched capacitor instrumentation amplifier is presented. Offset is reduced by an auto-zero technique and effects due to charge injection are attenuated by a special amplifier configuration. The circuit which is realized in a 4-/spl mu/m double poly process has an offset (/spl tau/) of 370 /spl mu/V, an rms input referred integrated noise (0.5 -f/sub c//2) of 79 /spl mu/V, and consumes only 21 /spl mu/W (f/sub c/ = 8 kHz, V/sub DD/ = 3 V).