Zr微合金化HSLA钢粗晶热影响区的组织和性能

用焊接热模拟法研究了Zr处理对 (%):≤ 0.18C-1.2～1.6Mn低合金高强度(HSLA)钢焊接粗晶热影响区(CGHAZ)组织和性能的影响。试验结果表明,Zr含量在0.01%～0.03%时,经过30～100kJ/cm线能量焊接热模拟后,CGHAZ的强度、塑性和-50℃冲击韧性都高于没有经过Zr处理的试验钢;Zr钢显微硬度(HV10)177～251,具有优良的焊接性。焊接线能量相同时,没有经过Zr处理试验钢CGHAZ的晶粒比Zr处理钢粗大;焊接线能量为 30kJ/cm时 ,各试验钢CGHAZ的组织以贝氏体为主 ,随着焊接线能量提高 ,CGHAZ中出现针状铁素体和少量珠光体。     

含Mg夹杂物对低合金高强度钢CGHAZ韧性的影响

摘要：采用Ca、Mg处理工艺研究不同夹杂物粒子对200kJ/cm大线能量焊接低合金高强度钢CGHAZ冲击韧性的影响,对各个试样CGHAZ的显微组织,晶粒尺寸和冲击功进行观察和分析。试验结果表明,在低合金高强度钢CGHAZ中,Mg处理钢的冲击性能明显高于Ca处理钢,主要原因是含Mg夹杂物粒子析出能力比含Ca夹杂物粒子强,在焊接过程中,含Mg夹杂物粒子对CGHAZ组织的钉扎作用更加显著;同时提高针状铁素体的含量,延长裂纹扩展路径,提高断裂时吸收的能量,使样品韧性得到提升。     

大线能量焊接用钢CGHAZ冲击韧性内在机理分析

针状铁素体(AF)一直被认为是提升大线能量焊接用钢粗晶热影响区(CGHAZ)韧性最有效的组织之一,但在一些试验中,有时即使发现CGHAZ中有大量AF组织,韧性也并不好。为了研究大线能量焊接用钢CGHAZ中不同类型组织及夹杂物对其冲击韧性的影响作用,从CGHAZ冲击试验出发,借鉴前人研究经验,对影响CGHAZ韧性的主要因素进行深入分析。结果显示,CGHAZ中微米级夹杂物容易成为裂纹萌生点,而晶内位错效应、冲击触发的体积效应等可以抑制裂纹传播,CGHAZ中析出的少量纳米级碳氮化物可以提升AF形核能力,增强CGHAZ韧性和强度,但当析出粒子过多时,会降低CGHAZ韧性。     

600 MPa级高能量输入焊接压力钢管用钢的研制

经过系列技术攻关,改进了武钢专用钢板冶炼及连铸过程中一些工艺,形成了一套自主操作技术模式,生产的微合金化低合金高强钢中杂质含量显著降低,钢板性能稳定性明显提高.利用武钢新改进的冶炼技术研制了一种600 MPa级低焊接裂纹敏感性高能量输入焊接水电站压力钢管用钢,研究了该钢的力学性能、微观组织结构以及焊接粗晶热影响区(CGHAZ)的组织特征及力学性能.结果表明,研制的新钢种集高强度、高韧性、优异的焊接性能于一体,且能承受大线能量焊接,焊前不预热,焊后不热处理.CGHAZ中弥散分布的复合氧化物夹杂促使针状铁素体的形成,提高了CGHAZ的力学性能.     

合金元素对大线能量焊接用钢组织性能的影响

为阐明钢中常用合金元素对大线能量焊接热影响区粗晶区(CGHAZ)的影响规律,设计了不同合金质量分数的试验钢,并进行氧化物冶金工艺处理,考察了各试验钢模拟焊接CGHAZ冲击韧性和组织特征。结果表明,低碳高锰有利于韧性的改善,但存在合适的碳质量分数范围,极低碳时需抑制晶界铁素体生成;添加质量分数为0.01%的铌时可保持较高的CGHAZ韧性,但过量的铌促进贝氏体生成而导致韧性恶化;添加质量分数为0.05%的钒时能提高基体强度并保持优良CGHAZ韧性,更高质量分数时因碳化物大量析出导致韧性下降;在一定范围内提高镍和铜质量分数可综合改善钢板强度和CGHAZ韧性;铬和钼的添加可抑制晶界转变产物,促进微细针状铁素体组织生成,但在试验钢成分下较多的M/A使得CGHAZ韧性未得到有效改善。     

600 MPa水电钢不同焊接热输入下焊接性能分析

采用埋弧焊,通过改变焊接工艺参数对600 MPa水电钢进行单面焊双面成型对接,运用金相显微镜、透射电镜观察了焊接接头的微观组织,并测试了焊接接头的力学性能。结果表明:接头焊缝组织为针状铁素体+先共析铁素体,随着焊接线能量的提高,先共析铁素体含量逐渐增加;热影响区组织为板条贝氏体+粒状贝氏体,随着线能量的提高,晶粒长大。焊接线能量为25~35 k J/cm,钢的强度、低温冲击性能具有较高的富余量。JH610CFD钢的最佳焊接线能量为≤35 k J/cm。     

不同冷速下钛微合金化Q345B钢的HAZ组织及性能

焊接热影响区(HAZ)的微观组织很大程度上决定了钢材焊接处的力学性能。为了掌握含钛微合金钢Q345B在不同焊接线能量下热影响区的微观组织及性能演变规律,采用Gleeble 3500热模拟试验机,对含钛微合金钢Q345B焊接过程中热影响区的组织演变进行模拟试验研究,分析了冷却速率对热影响区的微观组织及冲击韧性的影响。结果表明,大线能量焊接低冷速下热影响区组织以粒状贝氏体为主,t8/5为120 s时,析出针状铁素体,针状铁素体的出现有利于焊接热影响区冲击韧性的提升。     

桥梁钢Q420qD焊接热影响区组织性能研究

桥梁钢Q420q要求同时具有优异的强韧性和良好的可焊性,焊接热影响区(HAZ)的显微组织和性能直接影响构件焊接接头质量。20 mm厚度控轧控冷型Q420qD钢板在不进行焊前预热和焊后热处理条件下进行焊接试验,并针对其焊接热影响区的组织和性能展开分析研究。结果表明:当焊接线能量为15 kJ/cm时,焊接接头的力学性能达到国家标准;焊接接头各区域断口均由韧窝组成,呈现韧性断裂形貌;-20℃冲击功≥279 J,超过国家标准要求值;焊接接头区域未出现明显的软化、硬化现象;焊缝显微组织以针状铁素体为主,能有效阻碍裂纹扩展;熔合线显微组织包含粒状贝氏体、侧板条铁素体、针状铁素体和多边形铁素体;粗晶区的显微组织为粒状贝氏体、板条贝氏体、针状铁素体及少量多边形铁素体的混合组织;细晶区的显微组织为大量多边形铁素体、珠光体及少量渗碳体。     

高性能耐火耐候建筑用钢焊接性能研究

对武钢研制的高性能耐火耐候建筑用钢WGJ510C2的焊接性能，包括最高硬度、斜Y坡口、手弧焊焊接接头力学性能和不同线能量下模拟焊接热影响区（CGHAZ）的组织结构进行了研究，试验结果表明，该钢具有低的冷纹敏感性，其焊接性能优良，并能承受大线能量焊接。     

细晶组织耐候钢热影响区粗晶区的组织和性能

 采用焊接热模拟技术研究了焊接热循环对细晶组织09CuPCrNi钢热影响区粗晶区 (CGHAZ)显微组织和性能的影响。结果表明,在800~500 ℃冷却时间t8/5≤8 s时,该钢CGHAZ组织为贝氏体和少量马氏体。随着t8/5延长,在原奥氏体晶界上逐渐析出先共析铁素体,当t8/5＞18 s时,显微组织由大量铁素体和珠光体组成,且原奥氏体晶粒明显粗化,先共析铁素体含量增加。在-20 ℃和0 ℃下,t8/5对冲击吸收功影响较小,在-40 ℃时,随着t8/5延长,冲击吸收功下降显著,而且随着t8/5延长,CGHAZ硬度逐渐下降,但硬度值均高于母材,焊接热影响区相对于母材未出现软化倾向。     

低成本高焊接性能船板钢EH36的开发

工业化试制了3种厚度规格(20,26和36mm)的新型低成本高焊接性能船板钢EH36。试制钢板的显微组织由多边形铁素体和针状铁素体构成,其力学性能满足EH36级别船板要求并具有优异的低温韧性。采用焊接热模拟评价了钢板的焊接性能,当热输入由30kJ/cm升高至160kJ/cm时,粗晶区原奥氏体晶粒尺寸逐渐增大,其组织也逐渐由粒状贝氏体向晶界铁素体+晶内针状铁素体+晶内多边形铁素体转变,维氏硬度逐渐下降,低温韧性优异。得益于TiN粒子对奥氏体晶粒长大的抑制作用,微量B元素对先共析铁素体转变的抑制作用以及BN粒子对晶内铁素体形核的促进作用,焊接粗晶区获得了有利于韧性的细化组织,保证了粗晶区具有优异的低温韧性。双丝埋弧焊试验也验证了钢板具有优异的焊接性能。     

The significant impact of Ti content on microstructure–toughness relationship in the simulated coarse-grained heated-affected zone of high-strength low-alloy steels

This study aims to investigate the influence of Ti addition on microstructure and toughness in the simulated coarse-grained heated-affected zone (CGHAZ) of high-strength low-alloy steels. The steels with low and high Ti content respectively were subjected to 100?kJ/cm heat input welding thermal cycle. The results indicated that the second-phase particles were mainly oxide covered with MnS and fine (Ti,Nb)N precipitate in low-Ti steel, which were modified to the oxide surrounded by TiN and coarse (Ti,Nb)N precipitate in high-Ti steel. Compared with low-Ti steels, the coarser precipitates induced larger austenite grain in CGHAZ of high-Ti steel. Moreover, the wrapping of TiN decreases the ability of inclusion to promote the nucleation of acicular ferrite, resulting in lower fraction of acicular ferrite in CGHAZ of high-Ti steel. Content of martensite-austenite constituent increased in CGHAZ of high-Ti steel. They were all responsible for the degeneration in toughness in CGHAZ of high-Ti steel.     

Toughness improvement by Zr addition in the simulated coarse-grained heat-affected zone of high-strength low-alloy steels

The effect of Zr addition on the microstructure and impact toughness in the coarse-grained heat-affected zone (CGHAZ) of high-strength low-alloy steels subjected to 100?kJ?cm^-1 heat input was investigated. The second- phase particles were mainly Al–Ti complex oxides and (Ti,Nb)N precipitates in Zr-free steel, whereas lots of finer Zr–Al–Ti complex oxides and (Al,Ti,Nb)N precipitates were formed in Zr-bearing steel because of Zr addition. These finer oxides and precipitates effectively restricted the austenite grain growth by pinning effect during welding thermal cycle, and smaller and more uniform prior austenite grains were obtained in CGHAZ of Zr-bearing steel. Furthermore, more acicular ferrite grains nucleated on Zr–Al–Ti complex oxides, inducing formation of fine-grained microstructure in CGHAZ of Zr-bearing steel. The toughness improvement in CGHAZ of Zr-bearing steel with dimple fracture surface was attributed to the grain refinement by pinning effect and acicular ferrite formation.     

�����������Ӵ���EH40��������ͷ��֯������

Electro-slag welding with heat input of 530kJ/cm was applied to 60mm thick shipbuilding plate EH40, and microstructure and mechanical properties of the weld joint were characterized. Different regions such as heat affected zone, fusion zone, weld metal and base metal are found across the weld joint by microstructure analysis. A narrow coarse grain heat affected zone consisting of acicular ferrite, polygonal ferrite and grain boundary ferrite is found, width of which is less than 1mm. Acicular ferrite (?? 10??m) and grain boundary ferrite is observed at weld metal, while fusion zone have a complex structure of acicular ferrite, grain boundary ferrite and ferrite side plate. Mechanical property tests show that the absorbed energy of WM, FL and CGHAZ at -20?? during Charpy impact test is more than 60J, no evident softening phenomenon occurred at heat affected zone, and other properties met the requirement.     

Effect of Magnesium on Inclusion Formation in Ti-Killed Steels and Microstructurai Evolution in Welding Induced Coarse-Grained Heat Affected Zone

Effects of Mg on the chemical component and size distribution of Ti-bearing inclusions favored grain refinement of the welding induced coarse-grained heat affected zone (CGHAZ),with enhanced impact toughness in Ti-killed steels,which were examined based on experimental observations and thermodynamic calculations.The results indicated that the chemical constituents of the inclusions gradually varied from the Ti-O+Ti-Mg-O compound oxide to the Ti-Mg-O+ MgO compound oxide and the single-phase MgO,as the Mg content increased from 0.002 3% to 0.006%.A trace addition of Mg (approximately 0.002 %) led to the refinement of Ti-bearing inclusions by creating the Ti-Mg-O compound oxide and provided favorable size distribution of the inclusions for acicular ferrite transformation with a high nucleation rate in the CGHAZ,and a high volume fraction of acicular ferrite was obtained in the CGHAZ with enhanced impact toughness.Otherwise,a high content of Mg (approximately 0.006%) produced a single-phase MgO,which was impotent to nucleate an acicular ferrite,and a microstructure comprised of a ferrite side plate and a grain boundary ferrite developed in the CGHAZ.The experimental results were confirmed by thermodynamic calculations.     

Effect of Magnesium on Inclusion Formation in TiKilled Steels and Microstructural Evolution in Welding Induced CoarseGrained Heat Affected Zone

 Effects of Mg on the chemical component and size distribution of Ti bearing inclusions favored grain refinement of the welding induced coarse grained heat affected zone (CGHAZ), with enhanced impact toughness in Ti killed steels, which were examined based on experimental observations and thermodynamic calculations. The results indicated that the chemical constituents of the inclusions gradually varied from the Ti O+Ti Mg O compound oxide to the Ti Mg O+MgO compound oxide and the single phase MgO, as the Mg content increased from 0002 3% to 0006%. A trace addition of Mg (approximately 0002%) led to the refinement of Ti bearing inclusions by creating the Ti Mg O compound oxide and provided favorable size distribution of the inclusions for acicular ferrite transformation with a high nucleation rate in the CGHAZ, and a high volume fraction of acicular ferrite was obtained in the CGHAZ with enhanced impact toughness. Otherwise, a high content of Mg (approximately 0006%) produced a single phase MgO, which was impotent to nucleate an acicular ferrite, and a microstructure comprised of a ferrite side plate and a grain boundary ferrite developed in the CGHAZ. The experimental results were confirmed by thermodynamic calculations.     

钛稀土复合处理对C--Mn钢粗晶热影响区组织及韧性的影响

利用Gleeble-1500D热模拟机进行焊接热影响区热循环模拟实验,研究了在焊接热输入为65 kJ·cm-1时稀土单独处理和钛稀土复合处理对C-Mn钢粗晶热影响区组织及冲击韧性的影响,并利用扫描电镜观察和分析了实验钢中的夹杂物和冲击断口形貌,利用光镜观察了热循环模拟后实验钢中的微观组织.实验结果表明:稀土单独处理和钛稀土复合处理的试样微观组织分别主要是晶界铁素体+块状铁素体+针状铁素体和晶界铁素体+晶内针状铁素体.经稀土单独处理的试样中夹杂物为La₂O₂S+锰铝硅酸盐+MnS复合夹杂;钛稀土复合处理的试样中的夹杂主要是La₂O₂S+TiO_x+锰铝硅酸盐+MnS复合夹杂.钛稀土复合处理钢中的复合夹杂更细小,有利于形成细小的晶内针状铁素体.钛稀土复合处理极大地改善了实验钢的焊接热影响区低温冲击韧性,比稀土单独处理对试样的冲击性能提升效果更好.      

超低碳微合金X100管线钢CO2焊焊接接头的组织和性能

 采用CO2焊接方法焊接X100管线钢,分析了不同焊接工艺下焊接接头组织和性能的变化特征。随着焊接热输入的增加,焊接接头的屈服强度和抗拉强度降低,焊缝和热影响区处的冲击吸收功呈现先增大后减小的变化趋势,而焊缝组织均以针状铁素体（AF）为主。焊接热输入为1.17 kJ/mm时,粗晶区的显微组织主要是贝氏体铁素体（BF）,强韧匹配性最为优异;当热输入增加至1.91 kJ/mm时,粗晶区的组织除了BF外,还出现了粒状贝氏体（GB）,强韧水平明显降低。综合考虑,可将1.17 kJ/mm作为X100管线钢CO2焊接时的最佳热输入。