Numerical Rate Equation Modeling of a ${sim {hbox {2.1}}-}mu{hbox {m}}-{rm Tm}^{3+}/{rm Ho}^{3+}$ Co-Doped Tellurite Fiber Laser

Judd–Ofelt analysis is performed on measurements of bulk samples of ${rm Tm}^{3+}$ - and ${rm Ho}^{3+}$ -doped tellurite glass from which the host-dependent Judd–Ofelt intensity parameters are extracted. These have then been used to calculate the radiative rates and branching ratios in this particular material system. A rate-equation approach is then used to model an experimentally realized ${sim {hbox {2.1}}},mu{hbox {m}},{rm Tm}^{3+}/{rm Ho}^{3+}$ codoped tellurite fiber laser and extract values of the energy transfer and upconversion rate parameters in ${rm TeO}_{2}-{rm ZnO}-{rm Na}_{2}{rm O}$ (TZN) glass. Excellent agreement is found between simulated and experimental data, which indicates the validity of the approach.      

Performance Improvement of N-Type $hbox{TiO}_{x}$ Active-Channel TFTs Grown by Low-Temperature Plasma-Enhanced ALD

We report on performance improvement of $n$-type oxide–semiconductor thin-film transistors (TFTs) based on $hbox{TiO}_{x}$ active channels grown at 250 $^{circ}hbox{C}$ by plasma-enhanced atomic layer deposition. TFTs with as-grown $hbox{TiO}_{x}$ films exhibited the saturation mobility $(mu_{rm sat})$ as high as 3.2 $hbox{cm}^{2}/hbox{V}cdothbox{s}$ but suffered from the low on–off ratio $(I_{rm ON}/I_{rm OFF})$ of $hbox{2.0} times hbox{10}^{2}$. $hbox{N}_{2}hbox{O}$ plasma treatment was then attempted to improve $I_{rm ON}/I_{rm OFF}$. Upon treatment, the $hbox{TiO}_{x}$ TFTs exhibited $I_{rm ON}/I_{rm OFF}$ of $hbox{4.7} times hbox{10}^{5}$ and $mu_{rm sat}$ of 1.64 $hbox{cm}^{2}/hbox{V}cdothbox{s}$, showing a much improved performance balance and, thus, demonstrating their potentials for a wide variety of applications such as backplane technology in active-matrix displays and radio-frequency identification tags.      

2 MHz AO $Q$ -switched ${rm TEM}_{00}$ Grazing Incidence Laser With 3 at.% Neodymium Doped Nd:YVO$_{4}$

We present a detailed experimental and theoretical study of the ultrahigh repetition rate AO $Q$ -switched ${rm TEM}_{00}$ grazing incidence laser. Up to 2.1 MHz $Q$-switching with ${rm TEM}_{00}$ output of 8.6 W and 2.2 MHz $Q$ -switching with multimode output of 10 W were achieved by using an acousto-optics $Q$ -switched grazing-incidence laser with optimum grazing-incidence angle and cavity configuration. The crystal was 3 at.% neodymium doped Nd:YVO$_{4}$ slab. The pulse duration at 2 MHz repetition rate was about 31 ns. The instabilities of pulse energy at 2 MHz repetition rate were less than ${pm}6.7hbox{%}$ with ${rm TEM}_{00}$ operation and ${pm}3.3hbox{%}$ with multimode operation respectively. The modeling of high repetition rate $Q$-switched operation is presented based on the rate equation, and with the solution of the modeling, higher pump power, smaller section area of laser mode, and larger stimulated emission cross section of the gain medium are beneficial to the $Q$-switched operation with ultrahigh repetition rate, which is in consistent with the experimental results.      

Compact Variable ${rm TE}$-${rm TM}$ Polarization Splitter Based on Simplified Coherent Coupling in Lithium Niobate

A compact-sized electrically tunable ${rm TE}$- ${rm TM}$ mode splitter composed of a mode converter and an asymmetric Y-branch structure is presented. The asymmetric Y-branch consists of a straight and a bent waveguides to split two polarization modes based on the mode-sorting effect. To shorten the device length, a simplified coherently coupled-bending structure is utilized for the bent waveguide. Experimental results show that the device length is reduced about 52%, extinction ratios of both ${rm TE}$ and ${rm TM}$ modes are higher than 25 dB, yet the applied voltage is not significantly increased.      

Impacts of $hbox{N}_{2}$ and $hbox{NH}_{3}$ Plasma Surface Treatments on High-Performance LTPS-TFT With High-$kappa$ Gate Dielectric

Low-temperature polycrystalline-silicon thin-film transistors (LTPS-TFTs) with high- $kappa$ gate dielectrics and plasma surface treatments are demonstrated for the first time. Significant field-effect mobility $mu_{rm FE}$ improvements of $sim$86.0% and 112.5% are observed for LTPS-TFTs with $hbox{HfO}_{2}$ gate dielectric after $hbox{N}_{2}$ and $ hbox{NH}_{3}$ plasma surface treatments, respectively. In addition, the $hbox{N}_{2}$ and $ hbox{NH}_{3}$ plasma surface treatments can also reduce surface roughness scattering to enhance the field-effect mobility $mu_{rm FE}$ at high gate bias voltage $V_{G}$, resulting in 217.0% and 219.6% improvements in driving current, respectively. As a result, high-performance LTPS-TFT with low threshold voltage $V_{rm TH} sim hbox{0.33} hbox{V}$, excellent subthreshold swing S.S. $sim$0.156 V/decade, and high field-effect mobility $mu_{rm FE} sim hbox{62.02} hbox{cm}^{2}/hbox{V} cdot hbox{s}$ would be suitable for the application of system-on-panel.      

1580-V–40-$hbox{m}Omegacdot hbox{cm}^{2}$ Double-RESURF MOSFETs on 4H-SiC $(hbox{000}bar{hbox{1}})$

Double-reduced-surface-field (RESURF) MOSFETs with $hbox{N}_{2}hbox{O}$ -grown oxides have been fabricated on the 4H-SiC $(hbox{000} bar{hbox{1}})$ face. The double-RESURF structure is effective in reducing the drift resistance, as well as in increasing the breakdown voltage. In addition, by utilizing the 4H-SiC $(hbox{000}bar{hbox{1}})$ face, the channel mobility can be increased to over 30 $hbox{cm}^{2}/hbox{V}cdothbox{s}$, and hence, the channel resistance is decreased. As a result, the fabricated MOSFETs on 4H-SiC $( hbox{000}bar{hbox{1}})$ have demonstrated a high breakdown voltage $(V_{B})$ of 1580 V and a low on-resistance $(R_{rm ON})$ of 40 $hbox{m}Omega cdothbox{cm}^{2}$. The figure-of-merit $(V_{B}^{2}/R_{rm ON})$ of the fabricated device has reached 62 $hbox{MW/cm}^{2}$, which is the highest value among any lateral MOSFETs and is more than ten times higher than the “Si limit.”      

The Electrical and Interfacial Properties of Metal-High-$kappa$ Oxide-Semiconductor Field-Effect Transistors With $hbox{LaAlO}_{3}$ Gate Dielectric

$hbox{LaAlO}_{3}$ is a promising candidate for gate dielectric of future VLSI devices. In this letter, n-channel metal–oxide–semiconductor field-effect transistors with $hbox{LaAlO}_{3}$ gate dielectric were fabricated, and the electron mobility degradation mechanisms were studied. The leakage current density is $hbox{7.6} times hbox{10}^{-5} hbox{A/cm}^{2}$ at $-!$ 1 V. The dielectric constant is 17.5. The surface-recombination velocity, the minority-carrier lifetime, and the effective capture cross section of surface states were extracted from gated-diode measurement. The rate of threshold voltage change with temperature $(Delta V_{T} / Delta T)$ from 11 K to 400 K is $-!$ 1.51 mV/K, and the electron mobility limited by surface roughness is proportional to $E_{rm eff}^{-0.66}$.      

Extraction of the Effective Mobility of $ hbox{In}_{0.53}hbox{Ga}_{0.47}hbox{As}$ MOSFETs

The extraction of the effective mobility on $hbox{In}_{0.53} hbox{Ga}_{0.47}hbox{As}$ metal–oxide–semiconductor field-effect transistors (MOSFETs) is studied and shown to be greater than 3600 $hbox{cm}^{2}/hbox{V} cdot hbox{s}$. The removal of $C_{rm it}$ response in the split $C$–$V$ measurement of these devices is crucial to the accurate analysis of these devices. Low-temperature split $C$–$V$ can be used to freeze out the $D_{rm it}$ response to the ac signal but maintain its effect on the free carrier density through the substrate potential. Simulations that match this low-temperature data can then be “warmed up” to room temperature and an accurate measure of $Q_{rm inv}$ is achieved. These results confirm the fundamental performance advantages of $hbox{In}_{0.53}hbox{Ga}_{0.47}hbox{As}$ MOSFETs.      

A Center-Offset Polycrystalline-Silicon Thin-Film Transistor With ${rm n}^{+}$ Amorphous-Silicon Contacts

We have studied a bottom-gate polycrystalline-silicon thin-film transistor (poly-Si TFT) with amorphous-silicon (a-Si) ${rm n}^{+}$ contacts and center-offset gated structure, where intrinsic poly-Si is used in the center-offset region. The fabrication process is compatible with the conventional a-Si TFT with addition of thermal annealing for crystallization of a-Si. The bottom-gate poly-Si TFT with a 5-$muhbox{m}$ offset length exhibited a field-effect mobility of 18.3 $hbox{cm}^{2}/hbox{V} cdot hbox{s}$ and minimum OFF-state current of $hbox{2.79} times hbox{10}^{-12} hbox{A}/muhbox{m}$ at $V_{rm ds} = hbox{5} hbox{V}$. The leakage currents are two orders of magnitude lower than those of a nonoffset TFT with mobility drop from 23.8 to 18.3 $hbox{cm}^{2}/ hbox{V} cdot hbox{s}$.      

Electrical Properties of $hbox{Bi}_{5}hbox{Nb}_{3} hbox{O}_{15}$ Thin Film Grown on $hbox{TiN}/hbox{SiO}_{2}/ hbox{Si}$ at Room Temperature for Metal–Insulator–Metal Capacitors

Buckling was observed in $hbox{Bi}_{5}hbox{Nb}_{3}hbox{O}_{15}$ (BiNbO) films grown on $hbox{TiN}/hbox{SiO}_{2}/hbox{Si}$ at 300 $^{circ}hbox{C}$ but not in films grown at room temperature and annealed at 350 $^{circ}hbox{C}$. The 45-nm-thick films showed a high capacitance density and a low dissipation factor of 8.81 $hbox{fF}/muhbox{m}^{2}$ and 0.97% at 100 kHz, respectively, with a low leakage current density of 3.46 $hbox{nA}/hbox{cm}^{2}$ at 2 V. The quadratic and linear voltage coefficients of capacitance of this film were 846 $hbox{ppm}/hbox{V}^{2}$ and 137 ppm/V, respectively, with a low temperature coefficient of capacitance of 226 $hbox{ppm}/^{circ}hbox{C}$ at 100 kHz. This suggests that a BiNbO film grown on a $hbox{TiN}/ hbox{SiO}_{2}/hbox{Si}$ substrate is a good candidate material for high-performance metal–insulator–metal capacitors.      

High-Density and Low-Leakage-Current MIM Capacitor Using Stacked $hbox{TiO}_{2}/hbox{ZrO}_{2}$ Insulators

We have fabricated high-$kappa hbox{Ni}/hbox{TiO}_{2}/hbox{ZrO}_{2}/ hbox{TiN}$ metal–insulator–metal (MIM) capacitors. A low leakage current of $hbox{8} times hbox{10}^{-8} hbox{A/cm}^{2}$ at 125 $^{circ}hbox{C}$ was obtained with a high 38- $hbox{fF}/muhbox{m}^{2}$ capacitance density and better than the $hbox{ZrO}_{2}$ MIM capacitors. The excellent device performance is due to the lower electric field in 9.5-nm-thick $hbox{TiO}_{2}/ hbox{ZrO}_{2}$ devices to decrease the leakage current and to a higher $kappa$ value of 58 for $ hbox{TiO}_{2}$ as compared with that of $hbox{ZrO}_{2}$ to preserve the high capacitance density.      

Effective Modulation of Quadratic Voltage Coefficient of Capacitance in MIM Capacitors Using $hbox{Sm}_{2}hbox{O}_{3}/hbox{SiO}_{2}$ Dielectric Stack

We report the first demonstration of metal–insulator–metal (MIM) capacitors with $hbox{Sm}_{2}hbox{O}_{3}/hbox{SiO}_{2}$ stacked dielectrics for precision analog circuit applications. By using the “canceling effect” of the positive quadratic voltage coefficient of capacitance (VCC) of $hbox{Sm}_{2}hbox{O}_{3}$ and the negative quadratic VCC of $hbox{SiO}_{2}$, MIM capacitors with capacitance density exceeding 7.3 $hbox{fF}/muhbox{m}^{2}$ , quadratic VCC of around $-hbox{50} hbox{ppm/V}^{2}$ , and leakage current density of $hbox{1} times hbox{10}^{-7} hbox{A/cm}^{2}$ at $+$3.3 V are successfully demonstrated. The obtained capacitance density and quadratic VCC satisfy the technical requirements specified in the International Technology Roadmap for Semiconductors through the year 2013 for MIM capacitors to be used in precision analog circuit applications.      

Low Turn-On Voltage and High-Current $hbox{InP}/ hbox{In}_{0.37}hbox{Ga}_{0.63}hbox{As}_{0.89}hbox{Sb}_{0.11}/hbox{In}_{0.53}hbox{Ga}_{0.47}hbox{As}$ Double Heterojunction Bipolar Transistors

We report on the dc and microwave characteristics of an $ hbox{InP/In}_{0.37}hbox{Ga}_{0.63}hbox{As}_{0.89}hbox{Sb}_{0.11}/hbox{In}_{0.53}hbox{Ga}_{0.47}hbox{As}$ double heterojunction bipolar transistor grown by solid-source molecular beam epitaxy. The pseudomorphic $hbox{In}_{0.37}hbox{Ga}_{0.63}hbox{As}_{0.89}hbox{Sb}_{0.11}$ base reduces the conduction band offset $Delta E_{C}$ at the emitter/base junction and the base band gap, which leads to a very low $V_{rm BE}$ turn-on voltage of 0.35 V at 1 $hbox{A/cm}^{2}$ . A current gain of 125 and a peak $f_{T}$ of 238 GHz have been obtained on the devices with an emitter size of $hbox{1}times hbox{10} muhbox{m}^{2}$, suggesting that a high collector average velocity and a high current capability are achieved due to the type-II lineup at the InGaAsSb/InGaAs base/collector junction.      

Experimental Demonstration of Deeply-Etched SiO$_{2}$ Ridge Optical Waveguides and Devices

Deeply-etched ${hbox{SiO}}_{2}$ optical ridge waveguides are fabricated and characterized. A detailed discussion of the fabrication process (especially for the deep etching process) is presented. The measured propagation losses for the fabricated waveguides with different core widths range from $0.33sim {hbox {0.81}}~{hbox {dB}}/{hbox {mm}}$. The loss is mainly caused by the scattering due to the sidewall roughness. The losses in bending sections are also characterized, which show the possibility of realizing a small bending radius (several tens of microns). 1 $,times {rm N}$ ( ${rm N}=2$, 4, 8) multimode interference couplers based on the deeply-etched ${hbox{SiO}}_{2}$ ridge waveguide are also fabricated and show fairly good performances.      

Electrical Properties of $hbox{Ga}_{2}hbox{O}_{3}/ hbox{GaAs}$ Interfaces and GdGaO Dielectrics in GaAs-Based MOSFETs

Electrical properties of $hbox{Ga}_{2}hbox{O}_{3}/hbox{GaAs}$ interfaces with GdGaO cap dielectrics used in recent enhancement-mode GaAs-based NMOSFETs which perform in line with theoretical model predictions are presented. Capacitors with GdGaO thickness ranging from 3.0 to 18 nm ($hbox{0.9} leq hbox{EOT} leq hbox{3.9} hbox{nm}$) have been characterized by capacitance–voltage measurements. Midgap interface state density $D_{rm it}$, effective workfunction $phi_{m}$, fixed charge $Q_{f}$, dielectric constant $kappa$, and low field leakage current density are $hbox{2} times hbox{10}^{11} hbox{cm}^{-2} cdot hbox{eV}^{-1}$, 4.93 eV, $-hbox{8.9} times hbox{10}^{11} hbox{cm}^{-2}$, 19.5, and $hbox{10}^{-9}{-} hbox{10}^{-8} hbox{A/cm}^{2}$, respectively. The presence of interfacial Gd was confirmed to dramatically degrade electrical interface properties. The data illuminate the intimate interplay between heterostructure and interface engineering to achieve optimum MOSFET operation.      

A 10-kV Monolithic Darlington Transistor With $beta_{ rm forced}$ of 336 in 4H-SiC

4H-SiC bipolar Darlington transistors with a record-high current gain have been demonstrated. The dc forced current gain was measured up to 336 at 200 $hbox{W/cm}^{2}$ ( $J_{C} = hbox{35} hbox{A/cm}^{2}$ at $V_{rm CE} = hbox{5.7} hbox{V}$) at room temperature. The current gain exhibits a negative temperature coefficient and remains as high as 135 at 200 $^{circ}hbox{C}$. The specific on-resistance is 140 $hbox{m}Omegacdothbox{cm}^{2}$ at room temperature and increases at elevated temperatures. An open-emitter breakdown voltage $(BV_{rm CBO})$ of 10 kV was achieved at a leakage current density of $≪hbox{1} hbox{mA/cm}^{2}$. The device exhibits an open-base breakdown voltage $(BV_{rm CEO})$ of 9.5 kV. The high current gain of SiC Darlington transistors can significantly reduce the gate-drive power consumption with the same forward-voltage drop as that of 10-kV SiC bipolar junction transistors, thus making the device attractive for high-power high-temperature applications.      

Positive Bias Temperature Instability (PBTI) Characteristics of Contact-Etch-Stop-Layer-Induced Local-Tensile-Strained $hbox{HfO}_{2}$ nMOSFET

The positive bias temperature instability (PBTI) characteristics of contact-etch-stop-layer (CESL)-strained $hbox{HfO}_{2}$ nMOSFET are thoroughly investigated. For the first time, the effects of CESL on an $hbox{HfO}_{2}$ dielectric are investigated for PBTI characteristics. A roughly 50% reduction of $V_{rm TH}$ shift can be achieved for the 300-nm CESL $hbox{HfO}_{2}$ nMOSFET after 1000-s PBTI stressing without obvious $ hbox{HfO}_{2}/hbox{Si}$ interface degradation, as demonstrated by the negligible charge pumping current increase ($≪$ 4%). In addition, the $hbox{HfO}_{2}$ film of CESL devices has a deeper trapping level (0.83 eV), indicating that most of the shallow traps (0.75 eV) in as-deposited $ hbox{HfO}_{2}$ film can be eliminated for CESL devices.      

A 2–40 GHz Active Balun Using 0.13 $mu{rm m}$ CMOS Process

A 2 to 40 GHz broadband active balun using 0.13 $mu{rm m}$ CMOS technology is presented in this letter. Using two-stage differential amplified pairs, the active balun can achieve a wideband performance with the gain compensation technique. This active balun exhibits a measured small signal gain of ${0} pm{1}~{rm dB}$, with the amplitude imbalances below 0.5 dB and the phase differences of ${180} pm {10} ^{circ}$ from 2 to 40 GHz. The core active balun has a low power consumption of 40 mW, and a compact area of 0.8 mm $times,$ 0.7 mm. This proposed balun achieved the highest operation frequency, the widest bandwidth, and the smallest size among all the reported active baluns.      

$hbox{TiN/ZrO}_{2}$/Ti/Al Metal–Insulator–Metal Capacitors With Subnanometer CET Using ALD-Deposited $hbox{ZrO}_{2}$ for DRAM Applications

We provide the first report of the structural and electrical properties of $hbox{TiN/ZrO}_{2}$/Ti/Al metal–insulator–metal capacitor structures, where the $hbox{ZrO}_{2}$ thin film (7–8 nm) is deposited by ALD using the new zirconium precursor ZrD-04, also known as Bis(methylcyclopentadienyl) methoxymethyl. Measured capacitance–voltage ($C$– $V$) and current–voltage ( $I$–$V$) characteristics are reported for premetallization rapid thermal annealing (RTP) in $hbox{N}_{2}$ for 60 s at 400 $^{circ}hbox{C}$, 500 $^{circ}hbox{C}$, or 600 $^{ circ}hbox{C}$. For the RTP at 400 $^{circ}hbox{C}$ , we find very low leakage current densities on the order of nanoamperes per square centimeter at a gate voltage of 1 V and low capacitance equivalent thickness values of $sim$ 0.9 nm at a gate voltage of 0 V. The dielectric constant of $ hbox{ZrO}_{2}$ is 31 $pm$ 2 after RTP treatment at 400 $^{circ}hbox{C}$.      

A Comparative NBTI Study of $hbox{HfO}_{2}$, $hbox{HfSiO}_{x}$, and SiON p-MOSFETs Using UF-OTF $I_{rm DLIN}$ Technique

The time, temperature, and oxide-field dependence of negative-bias temperature instability is studied in $hbox{HfO}_{2}/hbox{TiN}$, $ hbox{HfSiO}_{x}/hbox{TiN}$, and SiON/poly-Si p-MOSFETs using ultrafast on-the-fly $I_{rm DLIN}$ technique capable of providing measured degradation from very short (approximately microseconds) to long stress time. Similar to rapid thermal nitrided oxide (RTNO) SiON, $hbox{HfO}_{2}$ devices show very high temperature-independent degradation at short (submilliseconds) stress time, not observed for plasma nitrided oxide (PNO) SiON and $hbox{HfSiO}_{x}$ devices. $hbox{HfSiO}_{x}$ shows lower overall degradation, higher long-time power-law exponent, field acceleration, and temperature activation as compared to $hbox{HfO}_{2}$, which are similar to the differences between PNO and RTNO SiON devices, respectively. The difference between $ hbox{HfSiO}_{x}$ and $hbox{HfO}_{2}$ can be attributed to differences in N density in the $hbox{SiO}_{2}$ IL of these devices.