A 4.69-W/mm output power density InAlN/GaN HEMT grown on sapphire substrate

We report high performance InAlN/GaN HEMTs grown on sapphire substrates.The lattice-matched InAlN/GaN HEMT sample showed a high 2DEG mobility of 1210 cm²/（V·s） under a sheet density of 2.6×10¹³ cm^-2.Large signal load-pull measurements for a（2×100μm）×0.25μm device have been conducted with a drain voltage of 24 V at 10 GHz.The presented results confirm the high performances reachable by InAlN-based technology with an output power density of 4.69 W/mm,a linear gain of 11.8 dB and a peak power-added efficiency of 48%.This is the first report of high performance InAlN/GaN HEMTs in mainland China.     

RF and microwave characteristics of a 10 nm thick InGaN-channel gate recessed HEMT

A new depletion-mode gate recessed AlGaN/InGaN/GaN-high electron mobility transistor(HEMT)with 10 nm thickness of InGaN-channel is proposed.A growth of AlGaN over GaN leads to the formation of twodimensional electron gas(2DEG)at the heterointerface.High 2DEG density(ns)is achieved at the heterointerface due to a strain induced piezoelectric effect between AlGaN and GaN layers.The electrons are confined in the InGaN-channel without spilling over into the buffer layer,which also reduces the buffer leakage current.From the input transfer characteristics the threshold voltage is obtained as 4:5 V and the device conducts a current of 2 A/mm at a drain voltage of 10 V.The device also shows a maximum output current density of 1.8 A/mm at Vds of 3 V.The microwave characteristics like transconductance,cut-off frequency,max frequency of oscillation and Mason’s Unilateral Gain of the device are studied by AC small-signal analysis using a two-port network.The stability and power performance of the device are analyzed by the Smith chart and polar plots respectively.To our knowledge this proposed InGaN-channel HEMT structure is the first of its kind.     

Performance analysis of 20 nm gate-length In0.2Al0.8N/GaN HEMT with Cu-gate having a remarkable high ION/IOFF ratio

Abstract： We propose a new structure of InxAll-xN/GaN high electron mobility transistor （HEMT） with gate length of 20 nm. The threshold voltage of this HEMT is achieved as -0.472 V. In this device the InA1N barrier layer is intentionally n-doped to boost the ION/IOFF ratio. The InAlN layer acts as donor barrier layer for this HEMT which exhibits an ION = 10-4.3 A and a very low IOFF = 10-14.4 A resulting in an ION/IoFF ratio of 1010.1. We compared our obtained results with the conventional InAlN/GaN HEMT device having undoped barrier and found that the proposed device has almost l0s times better ION/IOFF ratio. Further, the mobility analysis in GaN channel of this proposed HEMT structure along with DC analysis, C-V and conductance characteristics by using small-signal analysis are also presented in this paper. Moreover, the shifts in threshold voltage by DIBL effect and gate leakage current in the proposed HEMT are also discussed. InAlN was chosen as the most preferred barrier layer as a replacement of AlGaN for its excellent thermal conductivity and very good scalability.     

A high-performance enhancement-mode AIGaN/GaN HEMT

An enhancement-mode AlGaN/GaN HEMT with a threshold voltage of 0.35 V was fabricated by fluorine plasma treatment.The enhancement-mode device demonstrates high-performance DC characteristics with a saturation current density of 667 mA/mm at a gate bias of 4 V and a peak transconductance of 201 mS/mm at a gate bias of 0.8 V. The current-gain cut-off frequency and the maximum oscillation frequency of the enhancement-mode device with a gate length of 1μm are 10.3 GHz and 12.5 GHz,respectively,which is compa...     

蓝宝石衬底上输出功率密度为4.69W/mm的InAlN/GaN HEMT

We report high performance InAlN/GaN HEMTs grown on sapphire substrates. The lattice-matched InAlN/GaN HEMT sample showed a high 2DEG mobility of 1210 cm²/(V·s) under a sheet density of 2.6 × 10¹³ cm^-2. Large signal load-pull measurements for a (2 × 100 μm) × 0.25 μm device have been conducted with a drain voltage of 24 V at 10 GHz. The presented results confirm the high performances reachable by InAlN-based technology with an output power density of 4.69 W/mm, a linear gain of 11.8 dB and a peak power-added efficiency of 48%. This is the first report of high performance InAlN/GaN HEMTs in mainland China.     

基于氟等离子体表面处理技术的AlGaN/GaN HEMT器件栅正向泄漏电流研究

The gate forward leakage current in AlGaN/GaN high electron mobility transistors(HEMTs) is investigated. It is shown that the current which originated from the forward biased Schottky-gate contributed to the gate forward leakage current.Therefore,a fluorine-plasma surface treatment is presented to induce the negative ions into the AlGaN layer which results in a higher metal-semiconductor barrier.Consequently,the gate forward leakage current shrinks.Experimental results confirm that the gate forward leakage current is decreased by one order magnitude lower than that of HEMT device without plasma treatment.In addition,the DC characteristics of the HEMT device with plasma treatment have been studied.     

DC and RF characteristics of enhancement-mode InAIN/GaN HEMT with fluorine treatment

We report an enhancement-mode InA1N/GaN HEMT using a fluorine plasma treatment. The threshold voltage was measured to be ＋0.86 V by linear extrapolation from the transfer characteristics. The transconductance is 0 mS/mm at Vc, s = 0 V and VDS = 5 V, which shows a truly normal-offstate. The gate leakage current density of the enhancement-mode device shows two orders of magnitude lower than that of the depletion-mode device. The transfer characteristics of the E-mode InA1N/GaN HEMT at room temperature and high temperature are reported. The current gain cut-off frequency （fT） and the maximum oscillation frequency （fmax） of the enhancement-mode device with a gate length of 0.3 #m were 29.4 GHz and 37.6 GHz respectively, which is comparable with the depletion-mode device. A classical 16 elements small-signal model was deduced to describe the parasitic and the intrinsic parameters of the device.     

Field plated 0.15μm GaN HEMTs for millimeter-wave application

SiN dielectrically-defined 0.15μm field plated GaN HEMTs for millimeter-wave application have been presented.The AlGaN/GaN hetero-structure epitaxial material for HEMTs fabrication was grown on a 3-inch SiC substrate with an Fe doped GaN buffer layer by metal-organic chemical deposition.Electron beam lithography was used to define both the gate footprint and the cap of the gate with an integrated field plate.Gate recessing was performed to control the threshold voltage of the devices.The fabricated GaN HEMTs exhibited a unit current gain cut-off frequency of 39 GHz and a maximum frequency of oscillation of 63 GHz.Load-pull measurements carried out at 35 GHz showed a power density of 4 W/mm with associated power gain and power added efficiency of 5.3 dB and 35%,respectively,for a 0.15 mm gate width device operated at a 24 V drain bias.The developed 0.15μm gate length GaN HEMT technology is suitable for Ka band applications and is ready for millimeter-wave power MMICs development.     

RF-MBE Grown AlGaN/GaN HEMT Structure with High Al Content

A Si doped AlGaN/GaN HEMT structure with high Al content (x=43%) in the barrier layer is grown on sapphire substrate by RF-MBE.The structural and electrical properties of the heterostructure are investigated by the triple axis Xray diffraction and Van der PauwHall measurement,respectively.The observed prominent Bragg peaks of the GaN and AlGaN and the Hall results show that the structure is of high quality with smooth interface.The high 2DEG mobility in excess of 1260cm2／（V·s） is achieved with an electron density of 1.429e13cm－2 at 297K,corresponding to a sheet-densitymobility product of 1.8e16V－1·s－1.Devices based on the structure are fabricated and characterized.Better DC characteristics,maximum drain current of 1.0A/mm and extrinsic transconductance of 218mS/mm are obtained when compared with HEMTs fabricated using structures with lower Al mole fraction in the AlGaN barrier layer.The results suggest that the high Al content in the AlGaN barrier layer is promising in improving material electrical properties and device performance.     

槽栅MOSHEMT研制与特性分析

An A1GaN/GaN recessed-gate MOSHEMT was fabricated on a sapphire substrate. The device, which has a gate length of 1μm and a source-drain distance of 4μm, exhibits a maximum drain current density of 684mA/mrn at Vgs = 4V with an extrinsic transconductance of 219 mS/mm. This is 24.3% higher than the transconductance of conventional A1GaN/GaN HEMTs. The cut-off frequency and the maximum frequency of oscillation are 9.2 GHz and 14.1 GHz, respectively. Furthermore, the gate leakage current is two orders of magnitude lower than for the conventional Schottky contact device.     

Resolution Enhancement Technology:Integrated Process Solutions using OPC

DUV lithography, using the 248 nm wavelength, is a viable manufacturing option for devices with features at 130 nm and less. Given the low kl value of the lithography, integrated process development is a necessary method for achieving acceptable process latitude. The application of assist features for rule based OPC requires the simultaneous optimization of the mask, illumination optics and the resist.Described in this paper are the details involved in optimizing each of these aspects for line and space imaging.A reference pitch is first chosen to determine how the optics will be set. The ideal sigma setting is determined by a simple geometrically derived expression. The inner and outer machine settings are determined, in turn,with the simulation of a figure of merit. The maximum value of the response surface of this FOM occurs at the optimal sigma settings. Experimental confirmation of this is shown in the paper.Assist features are used to modify the aerial image of the more isolated images on the mask. The effect that the diffraction of the scattering bars (SBs) has on the image intensity distribution is explained. Rules for determining the size and placement of SBs are also given.Resist is optimized for use with off-axis illumination and assist features. A general explanation of the material' s effect is discussed along with the affect on the through-pitch bias. The paper culminates with the showing of the lithographic results from the fully optimized system.     

Cost-effective test solutions for smart card and other integrated flash applications

From its emergence in the late 1980s as a lower cost alternative to early EEPROM technologies, flash memory has evolved to higher densities and speedsand rapidly growing acceptance in mobile applications.In the process, flash memory devices have placed increased test requirements on manufacturers. Today, as flash device test grows in importance in China, manufacturers face growing pressure for reduced cost-oftest, increased throughput and greater return on investment for test equipment. At the same time, the move to integrated flash packages for contactless smart card applications adds a significant further challenge to manufacturers seeking rapid, low-cost test.     

Theoretical analysis of the relationship between the Brillouin gain coefficient and the strain in the optical-fiber sensors

The relation between the power of the Brillouin signal and the strain is one of the bases of the distributed fiber sensors of temperature and strain. The coefficient of the Bfillouin gain can be changed by the temperature and the strain that will affect the power of the Brillouin scattering. The relation between the change of the Brillouin gain coefficient and the strain is thought to be linear by many researchers. However, it is not always linear based on the theoretical analysis and numerical simulation. Therefore, errors will be caused if the relation between the change of the Brillouin gain coefficient and the strain is regarded as to be linear approximately for measuring the temperature and the strain. For this reason, the influence of the parameters on the Brillouin gain coefficient is proposed through theoretical analysis and numerical simulation.     

An improved parallel thinning algorithm with two subiterations

The parallel thinning algorithm with two subiterations is improved in this paper. By analyzing the notions of connected components and passes, a conclusion is drawn that the number of passes and the number of eight-connected components are equal. Then the expression of the number of eight-connected components is obtained which replaces the old one in the algorithm. And a reserving condition is proposed by experiments, which alleviates the excess deletion where a diagonal line and a beeline intersect. The experimental results demonstrate that the thinned curve is almost located in the middle of the original curve connectivelv with single pixel width and the processing speed is high.     

Novel fiber-optical interferometer with miniaturized probe for in-hole measurements

Today, micro-system technology and the development of new MEMS （Micro-Electro-Mechanical Systems） are emerging rapidly. In order for this development to become a success in the long run, measurement systems have to ensure product quality. Most often, MEMS have to be tested by means of functionality or destructive tests. One reason for this is that there are no suitable systems or sensing probes available which can be used for the measurement of quasi inaccessible features like small holes or cavities. We present a measurement system that could be used for these kinds of measurements. The system combines a fiber optical, miniaturized sensing probe with low-coherence interferometry, so that absolute distance measurements with nanometer accuracy are possible.     

Study of waveguide coupling efficiency in hybrid silicon lasers

This paper presents a new method to increase the waveguide coupling efficiency in hybrid silicon lasers. We find that the propagation constant of the InGaAsP emitting layer can be equal to that of the Si resonant layer through improving the design size of the InP waveguide. The coupling power achieves 42% of the total power in the hybrid lasers when the thickness of the bonding layer is 100 nm. Our result is very close to 50% of the total power reported by Intel when the thickness of the thin bonding layer is less than 5 nm. Therefore, our invariable coupling power technique is simpler than Intel＇s.     

Teleportation of an arbitrary unknown N-qubit entangled state under the controlling of M controllers

A new quantum protocol to teleport an arbitrary unknown N-qubit entangled state from a sender to a fixed receiver under M controllers(M < N) is proposed. The quantum resources required are M non-maximally entangled Greenberger-Home-Zeilinger (GHZ) state and N-M non-maximally entangled Einstein-Podolsky-Rosen (EPR) pairs. The sender performs N generalized Bell-state measurements on the 2N particles. Controllers take M single-particle measurement along x-axis, and the receiver needs to introduce one auxiliary two-level particle to extract quantum information probabilistically with the fidelity unit if controllers cooperate with it.     

A rigorous proof of MIMO channel capacity’s increase with antenna number

It is well known that adding more antennas at the transmitter or at the receiver may offer larger channel capacity in the multiple-input multiple-output（MIMO） communication systems. In this letter, a simple proof is presented for the fact that the channel capacity increases with an increase in the number of receiving antennas. The proof is based on the famous capacity formula of Foschini and Gans with matrix theory.     

Diode-end-pumped Nd:YVO4/LBO lasers with 4.2W continuous-wave output at 457 nm

A continuous-wave (CW) 457 nm blue laser operating at the power of 4.2 W is demonstrated by using a fiber coupled laser diode module pumped Nd: YVO4 and using LBO as the intra-cavity SHG crystal With the optimization of laser cavity and crystal parameters, the laser operates at a very high efficiency. When the pumping power is about 31 W, the output at 457nm reaches 4.2 W, and the optical to optical conversion efficiency is about 13.5% accordingly. The stability of the out putpower is better than 1.2% for 8 h continuously working.     

Call for Papers

正Wireless Body-area Networks The last decade has witnessed the convergence of three giant worlds:electronics,computer science and telecommunications.The next decade should follow this convergence in most of our activities with the generalization of sensor networks.In particular with the progress in medicine,people live longer and the aging of population will push the development of wireless personal networks