炭黑对ASA/天然石墨复合材料的电磁屏蔽性能影响

通过熔融共混方法制备导电高分子复合材料丙烯腈-苯乙烯-丙烯酸酯共聚物(ASA)/天然石墨(NGR)/炭黑(CB),采用电磁屏蔽测量仪、四探针电阻率测量仪和动态热机械分析仪对复合材料的电性能和力学性能进行详细研究。结果表明,ASA/NGR复合材料的体积电阻率随着炭黑含量增加而增加;同时在30 MHz~1500 MHz范围内,复合材料的电磁屏蔽性能从28 dB提高到38 dB,符合商业要求。炭黑的加入大大改善了材料力学性能,弯曲强度从31 MPa增加到41 MPa;动态储能模量从4.6 GPa增加到14.5 GPa。     

Hybrid composites of ABS with carbonaceous fillers for electromagnetic shielding applications

This work evaluates the influence of two types of carbonaceous fillers, carbon black (CB) and carbon nanotubes (CNTs), on the electrical, electromagnetic, and rheological properties of composites based on poly(acrylonitrile‐co‐butadiene‐co‐styrene) (ABS) prepared by the melt mixing. Electrical conductivity, electromagnetic shielding efficiency (EMI SE) in the X‐band frequency range (8–12.4 GHz), and melt flow index (MFI) results showed that ABS/CNT composites exhibit higher electrical conductivity and EMI SE, but lower MFI when compared to ABS/CB composites. The electrical conductivity of the binary composites showed an increase of around 16 orders of magnitude, when compared to neat ABS, for both fillers. Binary composites with 5 and 15 wt % of filler showed an EMI SE of, respectively, ?44 and ?83 dB for ABS/CNT, and ?9 and ?34 dB for ABS/CB. MFI for binary composites with 5 wt % were 15.45 and 0.55 g/10 min for CB and CNT, respectively. Hybrid composites ABS/CNT.CB with 3 wt % total filler and fraction 50:50 and 75:25 showed good correlation between EMI SE and MFI. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46546.     

Electrical,rheological and electromagnetic interference shielding properties of thermoplastic polyurethane/carbon nanotube composites

Electrically conducting rubbery composites based on thermoplastic polyurethane (TPU) and carbon nanotubes (CNTs) were prepared through melt blending using a torque rheometer equipped with a mixing chamber. The electrical conductivity, morphology, rheological properties and electromagnetic interference shielding effectiveness (EMI SE) of the TPU/CNT composites were evaluated and also compared with those of carbon black (CB)‐filled TPU composites prepared under the same processing conditions. For both polymer systems, the insulator–conductor transition was very sharp and the electrical percolation threshold at room temperature was at CNT and CB contents of about 1.0 and 1.7 wt%, respectively. The EMI SE over the X‐band frequency range (8–12 GHz) for TPU/CNT and TPU/CB composites was investigated as a function of filler content. EMI SE and electrical conductivity increased with increasing amount of conductive filler, due to the formation of conductive pathways in the TPU matrix. TPU/CNT composites displayed higher electrical conductivity and EMI SE than TPU/CB composites with similar conductive filler content. EMI SE values found for TPU/CNT and TPU/CB composites containing 10 and 15 wt% conductive fillers, respectively, were in the range ?22 to ?20 dB, indicating that these composites are promising candidates for shielding applications. © 2013 Society of Chemical Industry     

Investigation of the electric conductivity and the electromagnetic interference shielding efficiency of SWCNTs/GNS/PAni nanocomposites

This work demonstrates the fabrications and characterizations of polyaniline (PAni) composites containing single-walled carbon nanotubes (SWCNTs), graphite nanosheets (GNS), or hybrid fillers (SWCNTs/GNS). The characterization of microstructure, examination of fracture surface morphologies, and measurement of electric conductivity and electromagnetic interference shielding efficiency (EMI SE) were performed. It was found that both the electric conductivity and the EMI SE increase with filler loading, and the nanocomposites filled with 1.0 wt.% SWCNTs/GNS possessed the highest electric conductivity of 16.2 S/cm and total EMI SE of 27.0 dB. The experimental results also show that absorption is the primary mechanism of EMI SE for all of the loadings and fillers.     

Electrical conductivity and electromagnetic interference shielding effectiveness of carbon black/sisal fiber/polyamide/polypropylene composites

The effects of hybrid fillers on the electrical conductivity and electromagnetic interference (EMI) shielding effectiveness (SE) of polyamide 6 (PA6)/polypropylene (PP) immiscible polymer blends were investigated. Carbon black (CB) and steam exploded sisal fiber (SF) were used as fillers. CB was coated on the surface of SF, and this was exploded by water steam to form carbon black modified sisal fiber (CBMSF). CB/SF/PA6/PP composites were prepared by melt compounding, and its electromagnetic SE was tested in low‐frequency and high‐frequency ranges. We observed that SF greatly contributed to the effective decrease in the percolation threshold of CB in the PA6/PP matrix and adsorbed carbon particles to form a conductive network. Furthermore, an appropriate CB/SF ratio was important for achieving the best shielding performance. The results indicate that CBMSF was suitable for use as electronic conductive fillers and the CB/SF/PA6/PP composites could be used for the purpose of EMI shielding. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42801.     

Modification of sisal fiber by in situ coating steam explosion and electromagnetic interference shielding effectiveness of sisal fiber/PP composites

The technology of steam explosion was adopted to modify sisal fiber (SF) material and two different carbon particles, expanded graphite and conductive carbon black (CCB), were in situ coated on the surface of SF during steam explosion process. The DC conductivity and electromagnetic interference shielding effectiveness (SE) of the modified SF/polypropylene (PP) composites were studied and the measurement of electromagnetic interference (EMI) SE was conducted in two frequency ranges of 400–1,000 MHz and 1–18 GHz. The experimental results showed that this novel coating technology could improve the SE of the modified SF/PP composites significantly, which has a strong dependence on the loadings of the expanded graphite modified sisal fiber (SF‐EG) and conductive carbon black modified sisal fiber (SF‐CCB). When the loadings of SF‐EG and SF‐CCB reached 50 wt%, the maximum values of the SE were 33 dB and 51 dB, respectively. For the modified SF/PP composites, the experimental EMI SE values are in good correlation with the theoretical calculation values in far field of electromagnetic radiation. POLYM. COMPOS., 35:1038–1043, 2014. © 2013 Society of Plastics Engineers     

Electrical conductivity and EMI shielding effectiveness of polyurethane foam–conductive filler composites

The morphological, electrical, and thermal properties of polyurethane foam (PUF)/single conductive filler composites and PUF/hybrid conductive filler composites were investigated. For the PUF/single conductive filler composites, the PUF/nickel‐coated carbon fiber (NCCF) composite showed higher electrical conductivity and electromagnetic interference shielding effectiveness (EMI SE) than did the PUF/multiwall carbon nanotube (MWCNT) and PUF/graphite composites; therefore, NCCF is the most effective filler among those tested in this study. For the PUF/hybrid conductive fillers PUF/NCCF (3.0 php)/MWCNT (3.0 php) composites, the values of electrical conductivity and EMI SE were determined to be 0.171 S/cm and 24.7 dB (decibel), respectively, which were the highest among the fillers investigated in this study. NCCF and MWCNT were the most effective primary and secondary fillers, and they had a synergistic effect on the electrical conductivity and EMI SE of the PUF/NCCF/MWCNT composites. From the results of thermal conductivity and cell size of the PUF/conductive filler composites, it is suggested that a reduction in cell size lowers the thermal conductivity of the PUF/conductive filler composites. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44373.     

Studies on processing parameters and thermal stability of ENCF/ABS composites for EMI shielding

Electroless nickel coated carbon fibers (ENCF) were blended with acrylonitrile-butadiene-styrene (ABS) to prepare composites for electromagnetic interference (EMI) shielding. The effects of processing parameters, such as additives, temperature, and fiber loading amount, on EMI shielding effectiveness (SE) were researched. The thermal stability of EMI SE of ENCF/ABS composites was tested by heat treating composites in a drying oven at 60°C, and SE was measured at an interval of one week to consider the degradation of SE. The best SE of ENCF/ABS composites could be reached was 44 dB at optimum processing parameters. The thermal stability of ENCF/ABS composites for EMI shielding was steady without obvious degradation after 60°C heat treatment for five weeks. © 1997 John Wiley & Sons, Inc.     

Electromagnetic interference properties of carbon nanofiber–reinforced acrylonitrile–styrene–acrylate/natural graphite composites

Acrylonitrile–styrene–acrylate/natural graphite/carbon nanofiber composites (ASA/NG/CNF) were prepared using a melting blending method. The effects of CNFs on the morphology, rheological properties, dynamical mechanical properties, electrical resistivity, and electromagnetic interference shielding effectiveness (EMI SE) were studied using a scanning electron microscope, a rotational rheometer, and dynamic mechanical analysis (DMA). The addition of CNFs changed the oriented and laminated structure of the ASA/NG composite. The flexural strength of the ASA composite reached a maximum at 6% CNF, and then it began to decrease. The addition of CNFs did not alter the glass‐transition temperature of ASA, but it largely increased the storage modulus of the composite in DMA tests. In the rheological measurements, the complex viscosity and storage modulus of the composite increased as CNF content increased, and the resistance to creep of the composites was significantly increased by the addition of CNFs. The electrical resistivity of the ASA composites decreased from 49.8 Ω cm to 2.3 Ω cm as the CNF content was increased from 0 to 12%. At the same time, the EMI properties of the composites rose from 15 dB to 30 dB in the frequency range 30–1500 MHz. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45455.     

Synergistic effects of carbon nanotubes and exfoliated graphite nanoplatelets for electromagnetic interference shielding and soundproofing

Polypropylene/carbon nanotube/exfoliated graphite nanoplatelet (PP/CNT/xGnP) composites have been fabricated to evaluate their electromagnetic interference shielding effectiveness (EMI SE) and soundproofing. An EMI SE of 36.5 dB at 1250 MHz was measured for the 80/10/10 wt % PP/CNT/xGnP composite; its sound transmission loss was more than 5 dB higher than that for pure PP at low frequencies (520–640 Hz). These results indicate simultaneous EMI SE and soundproofing. Transmission electron microscopy was used to study the microstructure and to probe synergetic effects between the CNTs and xGnPs. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 3947–3951, 2013     

Modeling for the electromagnetic properties and EMI shielding of Cf/mullite composites in the gigahertz range

The electromagnetic properties and EMI shielding effectiveness of C_f/mullite composites via the spark plasma sintering were intensively investigated in the gigahertz range (8.2–12.4 GHz). Experimental results have revealed excellent electromagnetic properties and a high value of EMI shielding effectiveness (nearly 40 dB) for C_f/mullite composites with 1.65 vol% carbon fillers at thickness of 2 mm. We quantitatively characterize the contributions of microstructural features to overall EMI shielding effectiveness using a micromechanics-based homogenization model. The EMI shielding effectiveness enhances with respect to the C_f volume concentration before the threshold. The increasing trend of EMI shielding effectiveness with respect to AC (alternating current) frequency can be attributed to enhanced conductivity at high gigahertz range. It is demonstrated that filler and frequency dependent interface effects are essential to obtain excellent electromagnetic properties of C_f/mullite composite. The present research can provide guidances for the design of ceramic-based composites applied in high-temperature EMI shielding devices.     

Shielding effectiveness of carbon‐filled polycarbonate composites

In this project, varying amounts of three different carbons [carbon black (CB), carbon nanotubes (CNT), and graphene nanoplatelets (GNP)] were added to polycarbonate (PC). The resulting single filler composites were tested for shielding effectiveness (SE). The effects of single fillers and combinations of two different carbon fillers were studied via a factorial design. At the highest single filler loadings, the following SE results were obtained at 800 MHz: 18.9 dB for 10 wt % CB/PC, 18.4 dB for 8 wt % CNT/PC, and 6.3 dB for 15 wt % GNP/PC. The highest SE value of 21.4 dB was measured for the 5 wt % CB/5 wt % CNT/PC composite and could be used in SE applications (typically > 20 dB is needed). Statistically significant equations were developed that could be used to predict the SE of composites containing these fillers. In addition, it was determined that the composite SE is higher than what would be expected from the additive effect of each single filler for the CB/GNP/PC composites. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42719.     

Electromagnetic interference shielding of graphite/acrylonitrile butadiene styrene composites

Dispersion of graphite within the acrylonitrile butadiene styrene matrix demonstrates enhanced electromagnetic interference shielding of composites through the use of tumble mixing technique. A shielding effectiveness of 60 dB with 15 wt % of graphite has been achieved. D shore hardness data revealed a little decrease in hardness of composites with rise in graphite content. DC conductivity measurements revealed a fairly low percolation threshold at 3 wt % of graphite. The conductivity exhibited by 15 wt % composite is 1.66 × 10⁻¹ S/cm. These composites are fit for use as an effective and convenient EMI shielding material because of easy processing, better hardness, light weight, and, reasonable shielding efficiency. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

The effects of MWCNT length on the mechanical,crystallization and electromagnetic interference shielding effectiveness of PP/MWCNT composites

The length of multi-walled carbon nanotubes (MWCNT) has an important influence on the properties of polymer/MWCNT composites. This study aims to examine the influence of the length of MWCNT on the mechanical properties, distribution, melting and crystallization behavior, and electromagnetic interference shielding effectiveness (EMI SE) of PP/MWCNT composites. The test results show that MWCNT of a short length contribute to better mechanical properties and have a better dispersion in the matrix. MWCNT also serve as a nucleating agent for PP, thereby increasing the crystallization temperature (T_c). In particular, short MWCNT provide PP/MWCNT composites with a greater degree of cyrstallinity. The conjunction of 8 wt% long MWCNT in PP/MWCNT composites results in an optimal electrical resistivity of 65.02 Ω-cm, and an average EMI SE of ?29.47 dB. The polymer/MWCNT composites have properties that can be adjusted by using different lengths of MWCNT, which is advantageous for application in diverse products.     

Effect of titanate coupling agent on electromagnetic interference shielding effectiveness and mechanical properties of PC–ABS–NCF composite

Nickel-coated carbon fibers (NCF) treated with a coupling agent (CA) have been used for preparing composites of polycarbonate (PC) and acrylonitrile—butadiene—styrene (ABS) (90/10%) by melt blending. These composites have been evaluated for electromagnetic interference shielding effectiveness (EMI SE), mechanical properties, dispersion, and adhesion of the polymer to a filler using the scanning electron microscope (SEM). There is an improvement in the EMI SE, tensile strength, and impact strength of the composite when the carbon fiber is coupled with titanate CA. In loading NCF in composite, the optimum concentration of the CA Lica 38 used is about 2.0 phf combined with 1.5 phf calcium stearate (Ca.st.) (on the weight percentage of fillers); the composite can reach an SE of 50 dB by the coaxial transmission line test method.     

Fabrication of novel polyaniline/flowerlike copper monosulfide composites with enhanced electromagnetic interference shielding effectiveness

Novel polyaniline (PANI)/flowerlike CuS composites with improved electromagnetic interference (EMI) shielding effectiveness (SE) were prepared through the in situ polymerization of PANI into the flowerlike CuS microspheres. X‐ray diffraction, scanning electron microscopy, Fourier transform infrared spectroscopy, ultraviolet–visible optical absorption spectroscopy, thermogravimetric analysis, electrical conductivity testing, and EMI SE testing were used to characterize the as‐obtained products. The results reveal that the flowerlike CuS was uniformly coated by a PANI shell. Most importantly, compared with the original CuS and pure PANI, the novel PANI/flowerlike CuS composites exhibited a remarkably enhanced SE. With a thickness of 3 mm, the optimal EMI SE of the PANI–CuS composites reached ?45.2 dB at 2.78 GHz, and an improved shielding efficiency below ?18 dB was also obtained over the frequency range from 300 kHz to 3 GHz. This suggested that these novel PANI/flowerlike CuS composites have promising applications in the field of shielding materials. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134 , 45232.     

Highly filled multilayer thermoplastic/graphene conducting composite structures with high strength and thermal stability for electromagnetic interference shielding applications

Polyvinyl chloride (PVC)/graphene and poly(methyl methacrylate) (PMMA)/graphene nanocomposites were made by solution casting technique with graphene weight fractions of 1, 5, 10, 15, and 20%. Multilayer structures of the composites were made by hot compression technique to study their electromagnetic interference shielding effectiveness (EMI SE). Tensile strength, hardness, and storage modulus of the nanocomposites were studied in relation with graphene weight fraction. There has been a substantial increase in the electrical conductivity and EMI SE of the composites with 15–20% filler loading. Differential thermal analysis of the composites shows improved thermal stability with an increase in graphene loading. PMMA/graphene composites have better thermal stability, whereas PVC/graphene composites have superior mechanical properties. About 2 mm thick multilayer structures of PMMA/graphene and PVC/graphene composites show a maximum EMI SE of 21 dB and 31 dB, respectively, in the X band at 20 wt % graphene loading. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47792.     

Effects of carbon fiber modification with multiwall CNT on the electrical conductivity and EMI shielding effectiveness of polycarbonate/carbon fiber/CNT composites

The effect of carbon fiber (CF) modification with multiwall carbon nanotube (CNT) on the electrical, mechanical, and rheological properties of the polycarbonate (PC)/CF/CNT composite was investigated. The CF and multiwall CNT (MWCNT) were treated with sulfuric acid and nitric acid (3:1 wt %) mixture, to modify the CF with the CNT. For the PC with acid-treated CNT (a-CNT) modified acid-treated CF (a-CF) (PC/a-CF/a-CNT) composite, the electrical conductivity, and the electromagnetic interference shielding effectiveness (EMI SE) showed the highest values, compared with those of the PC/a-CF and PC/a-CF/CNT composites. The EMI SE of the PC/a-CF (10 wt %)/a-CNT (0.5 wt %) composite was found to be 26 (dB at the frequency of 10.0 GHz, and the EMI SE was increased by 91.2%, compared to that of the PC/a-CF composite at the same amount of total filler content. Among the composites studied in this work, the PC/a-CF/a-CNT composite also showed the highest values of relative permittivity (ε_r) and dielectric loss factor. The above results suggest that the CF modification with the a-CNT significantly affected the electrical conductivity and EMI SE of the composite, and the hybrid fillers of the a-CNT and a-CF resulted in good electrical pathways in the PC/a-CF/a-CNT composite. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47302.     

Microwave dielectric properties and EMI shielding effectiveness of poly(styrene‐b‐styrene‐ butadiene‐styrene) copolymer filled with PAni.Dodecylbenzenesulfonic acid and carbon black

Conducting composites of polyaniline doped with dodecylbenzenesulfonic acid (PAni.DBSA), carbon black (CB) and poly(styrene‐b‐styrene‐butadiene‐b‐styrene) (STF) as supporting matrix were prepared by in situ polymerization. The influence of components and composition (% w/w) on the electromagnetic properties (dielectric constant ε′ and the dielectric loss ε″) and electromagnetic interference shielding effectiveness (EMI‐SE) of the materials were evaluated with a waveguide, using a microwave network analyzer from 8.2 to 12.4 GHz (X‐band). It was found that CB presence generates adverse effects on PAni.DBSA yield during synthesis, as it can be seen by X‐ray diffraction and TGA analyses. The type of PAni.DBSA formed modifies the composites properties. Dielectric constant, loss factor, and EMI shielding increase with conductive filler loading. Both the fillers, individually and in combination, increase the properties; however, the effect is not additive in nature. POLYM. ENG. SCI., 52:2041–2048, 2012. © 2012 Society of Plastics Engineers     

Substantially improving mechanical property of double percolated poly(phenylene sulfide)/poly(arylenesulfide sulfone)/graphene nanoplates composites with superior electromagnetic interference shielding performance

The electrical conductivity and electromagnetic interference (EMI) shielding effectiveness (SE) can be conspicuously enhanced at low conductive filler contents with the formation of segregated structure in the conductive polymer composites (CPCs). Nevertheless, poor interface adhesion of segregated composites results in poor mechanical properties due to the selective distribution of conductive fillers. In this work, a flexible approach was applied to fabricate the poly(phenylene sulfide)/poly(arylene sulfide sulfone)/graphene nanoplates (GNPs) composite with a unique double percolated structure. This composite exhibits an outstanding EMI SE of 38.8 dB with only 3 wt % GNPs, which is comparable to that of the conventional segregated structure counterpart. What is more, the tensile strength and Young's modulus of double percolated composites with 3 wt % GNPs are remarkably improved by ~892 and ~274% compared to conventional segregated structure, achieving 37.7 and 1788.3 MPa, respectively. This work provides a valuable method for producing CPCs with high EMI shielding performances and outstanding mechanical properties. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 137, 48709.