Implementation of photovoltaic water pumping system with MPPT controls

To increase the output efficiency of a photovoltaic (PV) system, it is important to apply an efficient maximum power point tracking (MPPT) technique. This paper describes the analysis, the design and the experimental implementation of the tracking methods for a stand-alone PV system, using two approaches. The first one is the constant voltage (CV) MPPT method based on the optimum voltage, which was deduced experimentally, and considered as a reference value to extract the optimum power. The second one is the increment conductance (Inc-Cond) MPPT method based on the calculation of the power derivative extracted by the installation. The output controller can adjust the duty ratio to the optimum value. This optimum duty ratio is the input of a DC/DC boost converter which feeds a set of Moto-pump via a DC/AC inverter. This paper presents the details of the two approaches implemented, based on the system performance characteristics. Contributions are made in several aspects of the system, including converter design, system simulation, controller programming, and experimental setup. The MPPT control algorithms implemented extract the maximum power point (MPP), with satisfactory performance and without steady-state oscillation. MATLAB/Simulink and dSpace DS1104 are used to conduct studies and implement algorithms. The two proposed methods have been validated by implementing the performance of the PV pumping systems installed on the roof of the research laboratory in INSAT Tunisia. Experimental results verify the feasibility and the improved functionality of the system.     

A maximum power point tracking control strategy with variable weather parameters for photovoltaic systems with DC bus

In photovoltaic (PV) system, the most commonly used DC/DC converter is the basic buck or boost circuit to implement the maximum point power tracking (MPPT) due to their simple structure and low cost while there are some MPPT constraint conditions. By contrast, the conventional buck/boost DC/DC converter without MPPT constraint condition is seldom used because of its high cost or poor performance. To keep the advantages of these three DC/DC converters while overcoming their shortcomings, in this paper, the constraint conditions of capturing the maximum power point (MPP) of PV systems with direct-current (DC) bus are found out. Then, on the basis of this work, a MPPT control strategy with variable weather parameters is proposed. In this strategy, a new buck/boost DC/DC converter is proposed, which not only avoids the MPPT constraint conditions of basic buck or boost DC/DC converter but also overcomes the shortcomings of conventional buck/boost DC/DC converter. Finally, lots of simulated experiments verify the accuracy of MPPT constraint conditions, test the feasibility and availability of proposed MPPT control strategy, analyze the MPPT performance of proposed PV system and compare the output transient-state performance with conventional perturb and observe (P&O) method.     

Maximum power tracking for photovoltaic power system: Development and experimental comparison of two algorithms

This work presents an experimental comparison of two algorithms developed in order to maximize the output power from a photovoltaic (PV) system for the same given set of conditions. The maximum power point tracking (MPPT) methods proposed in this study are two extended algorithms: Perturb and Observe and Incremental Conductance. The numerical modelling of the PV system shows the MPPT interest and then the extended MPPT algorithms are highlighted. In this paper, a PV system based on a boost converter as MPPT device is considered. A programmable DC electronic load is fed by two identical PV systems in which the MPPT control converter algorithms are different. This experimental platform operates under the same conditions such as changing solar radiation and cell temperature. The experimental results obtained with a dSPACE controller board show the MPPT energy efficiency of the proposed algorithms.     

An integrated simulation model for PEM fuel cell power systems with a buck DC-DC converter

Fuel cell powered systems generally have a high current and a low voltage. Therefore, the output voltage of the fuel cell must be stepped-down using a DC-DC buck converter. However, since the fuel cell and converter have different dynamics, they must be suitably coordinated in order to satisfy the demanded load. Accordingly, this study commences by constructing a MATLAB/Simulink model of a proton exchange membrane fuel cell (PEMFC) system comprising a PEMFC stack, an air/fuel supply system, and a temperature control system. The validity of the PEMFC model is demonstrated by comparing the simulation results obtained for the polarzation curves of a single fuel cell with the corresponding experimental curves. A model is then constructed of the DC-DC buck converter used to step-down the PEMFC output voltage. In addition, a sliding mode control (SMC) scheme is proposed for the DC-DC buck converter which guarantees a low and stable output voltage given transient variations in the output voltage of the PEMFC. Finally, a model is constructed of a DC-AC inverter with a pulse width modulated (PWM) control scheme which enables the PEMFC stack to supply the grid or power AC applications directly. Overall, the combined PEMFC/DC-DC buck converter/DC-AC inverter model provides a powerful and versatile tool for the design and development of a wide range of PEMFC power systems.     

Adaptive fuzzy control with an optimization by using genetic algorithms for grid connected a hybrid photovoltaic–hydrogen generation system

The integration of significant amounts of renewable-storage hybrid power generation systems to the electric grid poses a unique set of challenges to utilities and system operators. This article deals with the designing methodology of an intelligent control based grid-connected a hybrid system composed of renewable energy source (RES) and storage system (SS). RES is a photovoltaic (PV) source and SS is a process of hydrogen transformation system (H₂TS) which composed of alkaline water electrolysis (AWE) for decomposition water by using the PV power, a tank used for gas storage and a proton exchange membrane (PEM) fuel cell (FC) to transform the H₂ to the electrical energy. The interconnection of the grid with the power generation system (PGS) is ensured through using a DC/AC hysteresis converter and it can synchronize current with the grid voltage among an independent control of active (P) and reactive (Q) power through a possibility of the Q compensation. In the proposed system, three algorithms are applied; two used inside generation and the third is used inside the grid. Perturb and observe (P&O) maximum power point tracking (MPPT) control algorithm always finds optimal power in the PV generator. A simple cascade controls loop of DC-DC boost converter and operate the FC generator to ensure maximum power and to regulate the DC Bus voltage. In addition, adaptive fuzzy logic control (FLC) unit is developed to control the DC/AC inverter, with adopting an off-line optimization based on genetic algorithms (GAs) applauded for tune different issues as scaling factors of the FLC and PIDs gains of the PV and the H₂TS control loops. Simulated results prove a big success of the proposed controls of the grid connected the hybrid PV-H₂TS with good performance.     

局部阴影条件下基于改进电导增量法的光伏系统最大功率跟踪方法

在局部阴影的情况下,由于串联式光伏组件的输出特性不同而产生多个极值点,使得传统的最大功率追踪（maximum power point tracking, MPPT）方法陷入局部极值点而失效。文中提出一种针对两级并网光伏系统的改进电导增量法以适应光伏阵列在局部阴影下的多峰值最大功率跟踪,通过分析最大功率点电压的变化范围,设定最大功率电压搜索范围以提高搜索效率,并通过DC/DC Boost变换器占空比实现输入电压控制,保证算法不陷入局部极值点。最后利用仿真实验验证了该算法在有、无阴影情况下均能准确地跟踪光伏方阵最大功率,有效提高了光伏阵列输出效率。     

Power quality improvement of solar photovoltaic transformer-less grid-connected system with maximum power point tracking control

This paper presents a transformer-less single-stage grid-connected solar photovoltaic (PV) system with active reactive power control. In the absence of active input power, grid-tied voltage source converter (VSC) is operated in the reactive power generation mode, which powers control circuitry and maintains regulated DC voltage. Control scheme has been implemented so that the grid-connected converter continuously serves local load. A data-based maximum power point tracking (MPPT) has been implemented at maximum power which performs power quality control by reducing total harmonic distortion (THD) in grid-injected current under varying environmental conditions. Standards (IEEE-519/1547) stipulates that current with THD greater than 5% cannot be injected into the grid by any distributed generation (DG) source. MPPT tracks actual variable DC link voltage while deriving maximum power from PV array and maintains DC link voltage constant by changing the converter modulation index. Simulation results with the PV model and MPPT technique validations demonstrate effectiveness of the proposed system.     

Optimal energy control of a PV-fuel cell hybrid system

This paper deals with a real time implementation of a fuzzy logic-based power management of a small scale generation hybrid power system. The system consists of a photovoltaic array and a fuel cell stack, supported by a single-phase grid that supplies a stand-alone AC load. The proposed supervisory algorithm guaranties the system to switch smart between two operation modes, according to the load demand, the gas level and the PV availability. Obviously, the PV side DC–DC converter is controlled to track permanently the maximum power point by using a fuzzy logic MPPT method; whereas, the fuel cell stack and the grid converters are tuned to cover the remaining power, or alternatively, injecting the exceeding power to the utility. Besides, to feed the AC load with a pure sine wave, a Back stepping algorithm is proposed to control the front-end single-phase inverter. To test the effectiveness of the proposed algorithms, experimental results obtained with a given load profile are presented and commented.     

Power quality investigation of a solar PV transformer-less grid-connected system fed DVR

This paper presents a single stage transformer-less grid-connected solar photovoltaic (PV) system with an active and reactive power control. In the absence of active input power, the grid-tied voltage source converter (VSC) is operated in a reactive power generation mode, which powers the control circuitry, and maintains a regulated DC voltage to the VSC. A data-based maximum power point tracking (MPPT) control scheme which performs power quality control at a maximum power by reducing the total harmonic distortion (THD) in grid injected current as per IEEE-519/1547 standards is implemented. A proportional-integral (PI) controller based dynamic voltage restorer (DVR) control scheme is implemented which controls the grid side converter during single-phase to ground fault. The analysis includes the grid current THD along with the corresponding variation of the active and reactive power during the fault condition. The MPPT tracks the actual variable DC link voltage while deriving the maximum power from the solar PV array, and maintains the DC link voltage constant by changing the modulation index of the VSC. Simulation results using Matlab/Simulink are presented to demonstrate the feasibility and validations of the proposed novel MPPT and DVR control systems under different environmental conditions.     

Modeling and simulation of three phase multilevel inverter for grid connected photovoltaic systems

This paper presents a control for a three phase five-level neutral clamped inverter (NPC) for grid connected PV system. The maximum power point tracking (MPPT) is capable of extracting maximum power from the PV array connected to each DC link voltage level. The MPPT algorithm is solved by fuzzy logic controller. The fuzzy MPPT is integrated with the inverter so that a DC–DC converter is not needed and the output shows accurate and fast response. A digital PI current control algorithm is used to remain the current injected into the grid sinusoidal and to achieve high dynamic performance with low total harmonic distortion (THD). The validity of the system is verified through MATLAB/Simulink and the results are compared with three phase three-level grid connected NPC inverter in terms of THD.     

Modeling,control and power management of hybrid photovoltaic fuel cells with battery bank supplying electric vehicle

In this paper, modeling, control and power management (PM) of hybrid Photovoltaic Fuel cell/Battery bank system supplying electric vehicle is presented. The HPS is used to produce energy without interruption. It consists of a photovoltaic generator (PV), a proton exchange membrane fuel cell (PEMFC), and a battery bank supplying an electric vehicle of 3 kW. In our work, PV and PEMFC systems work in parallel via DC/DC converter and the battery bank is used to store the excess of energy. The mathematical model topology and it power management of HPS with battery bank system supplying electric vehicle (EV) are the significant contribution of this paper. Obtained results under Matlab/Simulink and some experimental ones are presented and discussed.     

Maximum power point tracking of a proton exchange membrane fuel cell system using PSO-PID controller

Fuel cells output power depends on the operating conditions, including cell temperature, oxygen partial pressure, hydrogen partial pressure, and membrane water content. In each particular condition, there is only one unique operating point for a fuel cell system with the maximum output. Thus, a maximum power point tracking (MPPT) controller is needed to increase the efficiency of the fuel cell systems. In this paper an efficient method based on the particle swarm optimization (PSO) and PID controller (PSO-PID) is proposed for MPPT of the proton exchange membrane (PEM) fuel cells. The closed loop system includes the PEM fuel cell, boost converter, battery and PSO-PID controller. PSO-PID controller adjusts the operating point of the PEM fuel cell to the maximum power by tuning of the boost converter duty cycle. To demonstrate the performance of the proposed algorithm, simulation results are compared with perturb and observe (P&O) and sliding mode (SM) algorithms under different operating conditions. PSO algorithm with fast convergence, high accuracy and very low power fluctuations tracks the maximum power point of the fuel cell system.     

Modeling,control and simulation of a photovoltaic /hydrogen/ supercapacitor hybrid power generation system for grid-connected applications

Hybrid renewable energy systems (HRES) should be designed appropriately with an adequate combination of different renewable sources and various energy storage methods to overcome the problem of intermittency of renewable energy resources. Focusing on the inevitable impact on the grid caused by strong randomicity and apparent intermittency of photovoltaic (PV) generation system, modeling and control strategy of pure green and grid-friendly hybrid power generation system based on hydrogen energy storage and supercapacitor (SC) is proposed in this paper. Aiming at smoothing grid-connected power fluctuations of PV and meeting load demand, the alkaline electrolyzer (AE) and proton exchange membrane fuel cell (PEMFC) and SC are connected to DC bus of photovoltaic grid-connected generation system. Through coordinated control and power management of PV, AE, PEMFC and SC, hybrid power generation system friendliness and active grid-connection are realized. The validity and correctness of modeling and control strategies referred in this paper are verified through simulation results based on PSCAD/EMTDC software platform.     

Highly efficient maximum power point tracking using DC–DC coupled inductor single-ended primary inductance converter for photovoltaic power systems

Solar photovoltaics (PVs) have nonlinear voltage–current characteristics, with a distinct maximum power point (MPP) depending on factors such as solar irradiance and operating temperature. To extract maximum power from the PV array at any environmental condition, DC–DC converters are usually used as MPP trackers. This paper presents the performance analysis of a coupled inductor single-ended primary inductance converter for maximum power point tracking (MPPT) in a PV system. A detailed model of the system has been designed and developed in MATLAB/Simulink. The performance evaluation has been conducted on the basis of stability, current ripple reduction and efficiency at different operating conditions. Simulation results show considerable ripple reduction in the input and output currents of the converter. Both the MPPT and converter efficiencies are significantly improved. The obtained simulation results validate the effectiveness and suitability of the converter model in MPPT and show reasonable agreement with the theoretical analysis.     

A maximum power point tracking for photovoltaic-SPE system using a maximum current controller

Processes to produce hydrogen from solar photovoltaic (PV)-powered water electrolysis using solid polymer electrolysis (SPE) are reported. An alternative control of maximum power point tracking (MPPT) in the PV-SPE system based on the maximum current searching methods has been designed and implemented.Based on the characteristics of voltage–current and theoretical analysis of SPE, it can be shown that the tracking of the maximum current output of DC–DC converter in SPE side will track the MPPT of photovoltaic panel simultaneously.This method uses a proportional integrator controller to control the duty factor of DC–DC converter with pulse-width modulator (PWM).The MPPT performance and hydrogen production performance of this method have been evaluated and discussed based on the results of the experiment.     

ΔD法实现光伏系统最大功率点跟踪

在光伏系统中,光照强度、环境温度和负载变化等将会影响光伏系统的功率输出,因此光伏系统最大功率点跟踪(MPPT)是光伏系统研究的一个重要环节。文章在对比当前几种MPPT算法的基础上,通过改进扰动观察法得到了一种改变变换器开关频率占空比(D)来获得光伏系统最大输出功率的方案。利用MATLAB对光伏系统进行了不同工作条件下的仿真,证明其是可行的。同时,在一个实际光伏应用系统中进行占空比微增(ΔD)法最大功率点跟踪的应用试验。     

High-efficiency grid-connected photovoltaic module integrated converter system with high-speed communication interfaces for small-scale distribution power generation

This paper presents a high-efficiency grid-connected photovoltaic (PV) module integrated converter (MIC) system with reduced PV current variation. The proposed PV MIC system consists of a high-efficiency step-up DC-DC converter and a single-phase full-bridge DC-AC inverter. An active-clamping flyback converter with a voltage-doubler rectifier is proposed for the step-up DC-DC converter. The proposed step-up DC-DC converter reduces the switching losses by eliminating the reverse-recovery current of the output rectifying diodes. To reduce the PV current variation introduced by the grid-connected inverter, a PV current variation reduction method is also suggested. The suggested PV current variation reduction method reduces the PV current variation without any additional components. Moreover, for centralized power control of distributed PV MIC systems, a PV power control scheme with both a central control level and a local control level is presented. The central PV power control level controls the whole power production by sending out reference power signals to each individual PV MIC system. The proposed step-up DC-DC converter achieves a high-efficiency of 97.5% at 260 W output power to generate the DC-link voltage of 350 V from the PV voltage of 36.1 V. The PV MIC system including the DC-DC converter and the DC-AC inverter achieves a high-efficiency of 95% with the PV current ripple less than 3% variation of the rated PV current.     

Grid connected fuel cell and PV hybrid power generating system design with Matlab Simulink

Renewable energy sources have been taken the place of the traditional energy sources and especially rapidly developments of photovoltaic (PV) technology and fuel cell (FC) technology have been put forward these renewable energy sources (RES) in all other RES. PV systems have been started to be used widely in domestic applications connected to electrical grid and grid connected PV power generating systems have become widespread all around the world. On the other hand, fuel cell power generating systems have been used to support the PV generating so hybrid generation systems consist of PV and fuel cell technology are investigated for power generating. In this study, a grid connected fuel cell and PV hybrid power generating system was developed with Matlab Simulink. 160 Wp solar module was developed based on solar module temperature and solar irradiation by using real data sheet of a commercial PV module and then by using these modules 800 Wp PV generator was obtained. Output current and voltage of PV system was used for input of DC/DC boost converter and its output was used for the input of the inverter. PV system was connected to the grid and designed 5 kW solid oxide fuel cell (SOFC) system was used for supporting the DC bus of the hybrid power generating system. All results obtained from the simulated hybrid power system were explained in the paper. Proposed model was designed as modular so designing and simulating grid connected SOFC and PV systems can be developed easily thanks to flexible design.     

How fuzzy logic can improve PEM fuel cell MPPT performances?

This paper addresses the development of new variable step size fuzzy based MPPT controller. In this study, the fuzzy logic approach is firstly used to auto-scale the variable step size of the Incremental Conductance (IC) MPPT controller. Secondly, the proposed variable step size fuzzy based MPPT controller is used to track the output power of the PEM fuel cell system composed of 7 kW fuel cell supplying a 50Ω resistive load via a DC-DC boost converter controlled using the proposed MPPT. The proposed variable step size fuzzy-based MPPT controller is compared to the conventional fixed step size IC, the variable step size IC and the fuzzy scaled variable step size IC MPPTs using the implemented Matlab/Simulink PEM Fuel Cell power system model. Comparative simulation results between the four studied MPPTs show better performances for the proposed fuzzy based variable step size MPPT in term of: response time reduction between 3.6% and 82.35%; overshoot reduction between 34.55% and 100%; and ripple reduction between 70.93% and 100%, improving as consequence the fuel cell lifetime affected by high current ripple.     

基于Matlab/Simulink的三相光伏发电并网系统的仿真

根据光伏阵列的输出伏安特性,建立了光伏阵列通用仿真模型,并在此基础上提出了一种自适应占空比干扰观察法,建立了以Boost电路为核心的仿真模型,通过控制Boost DC-DC变换器实现了光伏阵列的最大功率点追踪（MPPT）,提高了光伏阵列的利用效率。对于三相光伏发电并网系统的研究,本文主要从PQ控制原理入手,在dq坐标系下建立了仿真模型,通过仿真得出PQ控制下的三相光伏发电并网运行特性,证明了仿真模型的正确性和有效性。