Hydrogen storage performance of 5LiBH4 + Mg2FeH6 composite system

The hydrogen storage properties of 5LiBH₄ + Mg₂FeH₆ reactive hydride composites for reversible hydrogen storage were investigated by comparing with the 2LiBH₄ + MgH₂ composite in the present work. The dehydrogenation pathway and reaction mechanism of 5LiBH₄ + Mg₂FeH₆ composite were also investigated and elucidated. The self-decomposition of Mg₂FeH₆ leads to the in situ formation of Mg and Fe particles on the surface of LiBH₄, resulting in a well dispersion between different reacting phases. The formation of FeB is observed during the dehydrogenation of 5LiBH₄ + Mg₂FeH₆ composite, which might supplies nucleation sites of MgB₂ during the dehydrogenation process, but is not an ascendant catalyst for the self-decomposition of LiBH₄. And FeB can also transform to the LiBH₄ and Fe by reacting with LiH and H₂ during the rehydrogenation process. The dehydrogenation capacity for 5LiBH₄ + Mg₂FeH₆ composite still gets to 6.5 wt% even after four cycles. The X-ray diffraction analyses reveal the phase transitions during the hydriding and dehydriding cycle. The formed FeB in the composite maintains a nanostructure after four hydriding-dehydriding cycles. The loss of hydrogen storage capacity and de-/rehydrogenation kinetics can be attributed to the incomplete generation of Mg₂FeH₆ during the rehydrogenation process.     

Enhanced dehydrogenation and rehydrogenation properties of LiBH4 catalyzed by graphene

The investigation of thermally induced dehydrogenation of LiBH₄ reveals that LiBH₄ doped with the graphene catalysts shows superior dehydrogenation and rehydrogenation performance to that of Vulcan XC-72, carbon nanotube and BP2000 doped LiBH₄. For doping with 20 wt.% graphene, thermal dehydrogenation of LiBH₄ is found to start at ca. 230 °C and a total weight loss of 11.4 wt.% can be obtained below 700 °C. With increased loading of graphene within a LiBH₄ sample, the onset dehydrogenation temperature and the two main desorption peaks from LiBH₄ are found to decrease while the hydrogen release amount is found to increase. Moreover, variation of the equilibrium pressure obtained from isotherms measured at 350–450 °C indicate the dehydrogenation enthalpy is reduced from 74 kJ mol⁻¹ H₂ for pure LiBH₄ to ca. 40 kJ mol⁻¹ H₂ for 20 wt.% graphene doped LiBH₄. Importantly, the reversible dehydrogenation/rehydrogenation process was achieved under 3 MPa H₂ at 400 °C for 10 h, with a capacity of ca. 4.0 wt.% in the tenth cycle. Especially, LiBH₄ is reformed and new species, Li₂B₁₀H₁₀, is detected after the rehydrogenation process.     

The milled LiBH4/h-BN composites exhibiting unexpected hydrogen storage kinetics and reversibility

The effect of nanoscale h-BN addition by milling on the de-/re-hydrogenation of LiBH₄ was investigated. With the increasing h-BN ratio, the milled LiBH₄/h-BN composites showed lower dehydrogenation temperature. For the LiBH₄-3BN composite (mole ratio 1:3), the on-set dehydrogenation temperature was reduced from 290 °C for the milled pure LiBH₄ down to 175 °C, and the initial dehydrogenation capacity could reach 3.1 wt.% (equivalent to 13.7 wt.% of the component LiBH₄) within ～2 h at 400 °C. Under moderate rehydrogenation conditions of 400 °C and 10 MPa H₂ pressure, the 2nd and 3th cyclic dehydrogenation capacity of LiBH₄-3BN composite almost remained unchanged, indicating remarkably improved rehydrogenation reversibility in comparison to milled pure LiBH₄. FTIR analysis reveals specific interaction between h-BN and LiBH₄ probably originating from the polar mechanism between polarizable B–H bond and B–N bond, which should be responsible for the enhanced dehydrogenation kinetics and reversibility. This work demonstrates the specific catalytic role of nanoscale h-BN and its potential for reversible hydrogen storage by compositing with high-capacity borohydrides.     

Rehydrogenation and cycle studies of LiBH4–CaH2 composite

Rehydrogenation behavior of 6LiBH₄ + CaH₂ composite with NbF₅ has been studied between 350 and 500 °C after dehydrogenation at 450 °C. The composite exhibits the best rehydrogenation feature at 450 °C in terms of the overall rehydrogenation rate and the amount of absorbed hydrogen. It is found that about 9 wt% hydrogen is absorbed at 450 °C for 12 h. Up to 10 dehydrogenation–hydrogenation cycles have been carried out for the composite. It is demonstrated that 6LiBH₄ + CaH₂ with 15 wt% NbF₅ maintains a reversible hydrogen storage capacity of about 6 wt% at 450 °C after a slight degradation between the 1st and 5th cycles. The addition of NbF₅ seems to improve the cycle properties by retarding microstructural coarsening during cycles.     

Combined effects of hydrogen back-pressure and NbF5 addition on the dehydrogenation and rehydrogenation kinetics of the LiBH4–MgH2 composite system

It is well known that the dehydrogenation pathway of the LiBH₄–MgH₂ composite system is highly reliant on whether decomposition is performed under vacuum or a hydrogen back-pressure. In this work, the effects of hydrogen back-pressure and NbF₅ addition on the dehydrogenation kinetics of the LiBH₄–MgH₂ system are studied under either vacuum or hydrogen back-pressure, as well as the subsequent rehydrogenation and cycling. For the pristine sample, faster desorption kinetics was obtained under vacuum, but the performance is compromised by slow absorption kinetics. In contrast, hydrogen back-pressure remarkably promotes the absorption kinetics and increases the reversible hydrogen storage capacity, but with the penalty of much slower desorption kinetics. These drawbacks were overcome after doping with NbF₅, with which the dehydrogenation and rehydrogenation kinetics was significantly improved. In particular, the enhanced kinetics was observed to persist well, even after 9 cycles, in the case of the NbF₅ doped sample under hydrogen back-pressure, as well as the suppression of forming Li₂B₁₂H₁₂. Furthermore, the mechanism that is behind these effects of NbF₅ additive on the reversible dehydrogenation reaction of the LiBH₄–MgH₂ system is discussed.     

Dehydrogenation and rehydrogenation of a 0.62LiBH4-0.38NaBH4 mixture with nano-sized Ni

The dehydrogenation reaction pathway of a 0.91 (0.62LiBH₄-0.38NaBH₄)-0.09Ni mixture in the temperature range of 25–650 °C in flowing Ar and the cycling stability in H₂ are presented. No H₂ is released immediately after melting at 225 °C. The major dehydrogenation occurs above 350 °C. Adding nano-sized Ni reduces the dehydrogenation peak temperatures by 20–25 °C, leading to three decomposition steps where Ni₄B₃ and Li_1.2Ni_2.5B₂ are found in the major dehydrogenation products for the 1^st and the 3^rd step; whilst the Ni-free mixture decomposes through a two-step decomposition pathway. A total of 8.1 wt% of hydrogen release from the 0.91 (0.62LiBH₄-0.38NaBH₄)-0.09Ni mixture is achieved at 650 °C in Ar. This mixture has a poor hydrogen cycling stability as its reversible hydrogen content decreases from 5.1 wt% to 1.1 wt% and 0.6 wt% during three complete desorption-absorption-cycles. However, the addition of nano-sized Ni facilitates the reformation of LiBH₄.     

Hydrogen sorption,kinetics, reversibility,and reaction mechanisms of MgH2-xLiBH4 doped with activated carbon nanofibers for reversible hydrogen storage based laboratory powder and tank scales

De/rehydrogenation kinetics and reversibility of MgH₂ are improved by doping with activated carbon nanofibers (ACNF) and compositing with LiBH₄. Via doping with 5 wt % ACNF, hydrogen absorption of Mg to MgH₂ (T = 320 °C and p(H₂) = 50 bar) increases from 0.3 to 4.5 wt % H₂. Significant reduction of onset dehydrogenation temperature of MgH₂ to 340 °C (ΔT = 70 °C as compared with pristine MgH₂) together with 6.8–8.2 wt % H₂ can be obtained by compositing Mg-5 wt. % ACNF with LiBH₄ (LiBH₄:Mg mole ratios of 0.5:1, 1:1, and 2:1). During dehydrogenation of Mg-rich composites (0.5:1 and 1:1 mol ratios), the formation of MgB₂ and Mg_0.816Li_0.184 implying the reaction between LiBH₄ and MgH₂ favors kinetic properties and reversibility, while the composite with 2:1 mol ratio shows individual dehydrogenation of LiBH₄ and MgH₂. For up-scaling to hydrogen storage tank (～120 times greater sample weight than laboratory scale) of the most suitable composite (1:1 mol ratio), de/rehydrogenation kinetics and hydrogen content released at all positions of the tank are comparable and approach to those from laboratory scale. Due to high purity (100%) and temperature of hydrogen gas from hydride tank, the performance of single proton exchange membrane fuel cell enhances up to 30% with respect to the results from compressed gas tank.     

Remarkable irreversible and reversible dehydrogenation of LiBH4 by doping with nanosized cobalt metalloid compounds

Nanosized cobalt sulfide and cobalt boride were synthesized and doped into LiBH₄ to improve the dehydrogenation properties of this important candidate for hydrogen storage. With respect to CoS_x doping, the dehydrogenation temperature (peak temperature observed by mass spectrometry) of pristine LiBH₄ can be reduced from 440 °C to 175 °C with a maximum capacity of 6.7 wt% at 50% doping. Unfortunately, B₂H₆ is liberated and the process is not reversible because the CoS_x dopant reacts with LiBH₄ to form more stable compounds. By changing CoS_x to CoB_x, a reversible dehydrogenation was realized with greatly improved reversibility. The dehydrogenation temperature was reduced to 350 °C with a maximum capacity of 8.4 wt% at 50% doping amount. It is very significant that CoB_x is stable and the release of B₂H₆ is eliminated. A reversible hydrogen desorption of about 5.3 wt% can be achieved with a LiBH₄ + 50% CoB_x mixture under a mild rehydrogenation condition of 400 °C at 10 MPa H₂. It is obvious that CoS_x acts as a reactant even though the dehydrogenation is greatly enhanced, while CoB_x behaves as a catalyst significantly promoting the dehydrogenation and reversibility of LiBH₄.     

Reversible hydrogen sorption and kinetics of hydrogen storage tank based on MgH2 modified by TiF4 and activated carbon

By doping with 5 wt % TiF₄ and activated carbon (AC), onset and main dehydrogenation temperatures of MgH₂ significantly reduce (ΔT = 138 and 109 °C, respectively) with hydrogen capacity of 4.4 wt % H₂. Up-scaling to storage tank begins with packing volume and sample weight of 28.8 mL and ～14.5 g, respectively, and continues to 92.6 mL and ～60.5–67 g, respectively. Detailed hydrogen sorption mechanisms and kinetics of the tank tightly packed with four beds of MgH₂TiF₄-AC (～60.5 g) are investigated. De/rehydrogenation mechanisms are detected by three temperature sensors located at different positions along the tank radius, while hydrogen permeability is benefited by stainless steel mesh sheets and tube inserted in the hydride beds. Fast desorption kinetics of MgH₂TiF₄-AC tank at ～275–283 °C, approaching to onset dehydrogenation temperature of the powder sample (272 °C) suggests comparable performances of laboratory and tank scales. Hydrogen desorption (T = 300 °C and P(H₂) = 1 bar) and absorption (T = 250 °C and P(H₂) = 10–15 bar) of MgH₂TiF₄-AC tank provide gravimetric and volumetric capacities during the 1^st-2nd cycles of 4.46 wt % H₂ and 28 gH₂/L, respectively, while those during the 3^rd-15th cycles are up to 3.62 wt % H₂ and 23 gH₂/L, respectively. Due to homogeneous heat transfer along the tank radius, de/rehydrogenation kinetics superior at the tank center and degrading forward the tank wall can be due to poor hydrogen permeability. Particle sintering and/or agglomeration upon cycling yield deficient hydrogen content reproduced.     

Reversible hydrogen storage in LiBH4/Ca(AlH4)2 systems

To improve the hydrogen storage property of LiBH₄, the LiBH₄/Ca(AlH₄)₂ reactive systems with various ratios were constructed, and their de-/hydrogenation properties as well as the reaction mechanisms were investigated experimentally. It was found that the sample with the LiBH₄ to Ca(AlH₄)₂ molar ratio of 6:1 exhibits the best comprehensive hydrogen storage properties, desorbing hydrogen completely (8.2 wt.%) within 35 min at 450 °C and reversibly absorbing 4.5 wt.% of hydrogen at 450 °C under a hydrogen pressure as low as 4.0 MPa. During the first dehydrogenation process of the LiBH₄/Ca(AlH₄)₂ systems, the CaH₂ and Al particles were in situ precipitated via the self-decomposition of Ca(AlH₄)₂, and then reacted with LiBH₄ to form CaB₆, AlB₂ and LiH. Whereafter, the sample can cycle between LiBH₄ + Ca(BH₄)₂ + Al in the hydrogenated state and CaB₆ + AlB₂ + LiH in the dehydrogenated state.     

Enhanced hydrogen storage properties of LiBH4 modified by NbF5

In this work, the hydriding–dehydriding properties of the LiBH₄–NbF₅ mixtures were investigated. It was found that the dehydrogenation and reversibility properties of LiBH₄ were significantly improved by NbF₅. Temperature-programed dehydrogenation (TPD) showed that 5LiBH₄–NbF₅ sample started releasing hydrogen from as low as 60 °C, and 4 wt.% hydrogen could be obtained below 255 °C. Meanwhile, ∼7 wt.% H₂ could be reached at 400 °C in 20LiBH₄–NbF₅ sample, whereas pristine LiBH₄ only released ∼0.7 wt.% H₂. In addition, reversibility measurement demonstrated that over 4.4 wt.% H₂ could still be released even during the fifth dehydrogenation in 20LiBH₄–NbF₅ sample. The experimental results suggested that a new borohydride possibly formed during ball milling the LiBH₄–NbF₅ mixtures might be the source of the active effect of NbF₅ on LiBH₄.     

Enhanced hydrogen storage properties of LiBH4-MgH2 composite by the catalytic effect of MoCl3

Though LiBH₄-MgH₂ system exhibits an excellent hydrogen storage property, it still presents high decomposition temperature over 350 °C and sluggish hydrogen absorption/desorption kinetics. In order to improve the hydrogen storage properties, the influence of MoCl₃ as an additive on the hydrogenation and dehydrogenation properties of LiBH₄-MgH₂ system is investigated. The reversible hydrogen storage performance is significantly improved, which leads to a capacity of about 7 wt.% hydrogen at 300 °C. XRD analysis reveals that the metallic Mo is formed by the reaction between LiBH₄ and MoCl₃, which is highly dispersed in the sample and results in improved dehydrogenation and hydrogenation performance of LiBH₄-MgH₂ system. From Kissinger plot, the activation energy for hydrogen desorption of LiBH₄-MgH₂ system with additive MoCl₃ is estimated to be ∼43 kJ mol⁻¹ H₂, 10 kJ mol⁻¹ lower than that for the pure LiBH₄-MgH₂ system indicating that the kinetics of LiBH₄-MgH₂ composite is significantly improved by the introduction of Mo.     

Enhanced hydrogen desorption from the Co-catalyzed LiBH4–Mg(BH4)2 eutectic composite

Co-based catalyst can significantly improve the dehydrogenation kinetics of the eutectic composite of LiBH₄–Mg(BH₄)₂ (1/1 M ratio). The onset hydrogen desorption temperature of the composite is at about 155 °C, which is ca. 245, 110 or 27 °C lower than that of LiBH₄, Mg(BH₄)₂ or pristine LiBH₄–Mg(BH₄)₂, respectively. Upon holding the samples at 270 °C, the Co catalyzed composite can release hydrogen at a rate 1.6 times faster than that of the pristine one. Electron Paramagnetic Resonance (EPR) characterization evidenced that Co was in a reduced state of Co⁺ which may serve as the functional species in catalyzing the dehydrogenation of the composite.     

Enhanced dehydrogenation properties of LiBH4 compositing with hydrogenated magnesium-rare earth compounds

LiBH₄ is regarded as a promising hydrogen storage material due to its high hydrogen density. In this study, the dehydrogenation properties of LiBH₄ were remarkably enhanced by doping hydrogenated Mg₃RE compounds (RE denotes La, Ce, Nd rare earth metals), which are composed of nanostructured MgH₂ and REH_2+x (denoted as H − Mg₃RE). For the LiBH₄ + H − Mg₃La mixture, the component LiBH₄ desorbed 6 wt.% hydrogen even at a relatively low temperature of 340 °C, far lower than the desorption temperature of pure LiBH₄ or the 2LiBH₄ + MgH₂ system. This kinetic improvement is attributed to the hydrogen exchange mechanism between the H − Mg₃La and LiBH₄, in the sense that the decomposition of MgH₂ and LaH_2+x catalyzed the dehydrogenation of LiBH₄ through hydrogen exchange effect rather than mutual chemical reaction requiring higher temperature and hydrogen pressure. However, prior to fast hydrogen release, the hydrogen exchange effect suppressed the dehydriding of MgH₂ and elevated its desorption temperature. It is expected to strengthen the hydrogen exchange effect by compositing the LiBH₄ with other nanosized metal hydrides and to obtain better dehydrogenation properties.     

Hydrogen generation from the ball milled composites of sodium and lithium borohydride (NaBH4/LiBH4) and magnesium hydroxide (Mg(OH)2) without and with the nanometric nickel (Ni) additive

The composites of (NaBH₄+2Mg(OH)₂) and (LiBH₄+2Mg(OH)₂) without and with nanometric Ni (n-Ni) added as a potential catalyst were synthesized by high energy ball milling. The ball milled NaBH₄-based composite desorbs hydrogen in one exothermic reaction in contrast to its LiBH₄-based counterpart which dehydrogenates in two reactions: an exothermic and endothermic. The NaBH₄-based composite starts desorbing hydrogen at 240 °C. Its ball milled LiBH₄-based counterpart starts desorbing at 200 °C. The latter initially desorbs hydrogen rapidly but then the rate of desorption suddenly decelerates. The estimated apparent activation energy for the NaBH₄-based composite without and with n-Ni is equal to 152 ± 2.2 and 157 ± 0.9 kJ/mol, respectively. In contrast, the apparent activation energy for the initial rapid dehydrogenation for the LiBH₄-based composite is very low being equal to 47 ± 2 and 38 ± 9 kJ/mol for the composite without and with the n-Ni additive, respectively. XRD phase studies after volumetric isothermal dehydrogenation tests show the presence of NaBO₂ and MgO for the NaBH₄-based composite. For the LiBH₄-based composite phases such as MgO, Li₃BO₃, MgB₂, MgB₆ are the products of the first exothermic reaction which has a theoretical H₂ capacity of 8.1 wt.%. However, for reasons which are not quite clear, the first reaction never goes to full completion even at 300 °C desorbing ∼4.5 wt.% H₂ at this temperature. The products of the second endothermic reaction for the LiBH₄-based composite are MgO, MgB₆, B and LiMgBO₃ and the reaction has a theoretical H₂ capacity of 2.26 wt.%. The effect of the addition of 5 wt.% nanometric Ni on the dehydrogenation behavior of both the NaBH₄-and LiBH₄-based composites is rather negligible. The n-Ni additive may not be the optimal catalyst for these hydride composite systems although more tests are required since only one n-Ni content was examined.     

Small hydrogen storage tank filled with 2LiBH4MgH2 nanoconfined in activated carbon: Reaction mechanisms and performances

De/rehydrogenation performances and reaction pathways of nanoconfined 2LiBH₄MgH₂ into activated carbon (AC) packed in small hydrogen storage tank are proposed for the first time. Total and material storage capacities upon five hydrogen release and uptake cycles are 3.56–4.55 and 2.03–3.28 wt % H₂, respectively. Inferior hydrogen content to theoretical capacity (material capacity of 5.7 wt % H₂) is due to partial dehydrogenation during sample preparation and incomplete decomposition of LiBH₄ as well as the formation of thermally stable Li₂B₁₂H₁₂ upon cycling. Two-step dehydrogenation of MgH₂ and LiBH₄ to produce Mg and MgB₂+LiH, respectively is found at all positions in the tank. For rehydrogenation, reversibility of MgH₂ and LiBH₄ proceeds via different reaction mechanisms. Although isothermal condition (T_set = 350 °C) and controlled pressure range (e.g., 30–40 bar H₂ for hydrogenation) are applied, temperature gradient inside the tank and poor hydrogen diffusion through hydride bed, especially in the sample bulk are detected. This results in alteration of de/rehydrogenation pathways of hydrides at different positions in the tank. Thus, further development of hydrogen storage tank based 2LiBH₄MgH₂ nanoconfined in AC includes the improvement of thermal conductivity of materials and temperature control system as well as hydrogen permeability.     

Effect of Al on the hydrogen storage properties of Mg(BH4)2

The various Mg–B–Al–H systems composed of Mg(BH₄)₂ and different Al-sources (metallic Al, LiAlH₄ and its decomposition products) have been investigated as potential hydrogen storage materials. The role of Al was studied on the dehydrogenation and the rehydrogenation of the systems. The results indicate that the different Al-sources exhibit a similar improving effect on the dehydrogenation properties of Mg(BH₄)₂. Taking the Mg(BH₄)₂ + LiAlH₄ system as an example, at first LiAlH₄ rapidly decomposes into LiH and Al, then Mg(BH₄)₂ decomposes into MgH₂ and B, finally the MgH₂ reacts with Al, LiH and B, which forms Mg₃Al₂ and MgAlB₄. The system starts to desorb H₂ at 140 °C and desorbs 3.6 wt.% H₂ below 300 °C, while individual Mg(BH₄)₂ starts to desorb H₂ at 250 °C and desorbs only 1.3 wt.% H₂ below 300 °C. The isothermal desorption kinetics of the Mg–B–Al–H systems is about 40% faster than that of Mg(BH₄)₂ at the hydrogen desorption ratio of 90%. In addition, the Mg–B–Al–H systems show partial reversibility at moderate temperature and pressure. For Al-added system, the product of rehydrogenation is MgH₂, while for LiAlH₄-added system the product is composed of LiBH₄ and MgH₂.     

Hydrogen storage behavior of 2LiBH4/MgH2 composites improved by the catalysis of CoNiB nanoparticles

2LiBH₄/MgH₂ system is a representative and promising reactive hydride composite for hydrogen storage. However, the high desorption temperature and sluggish desorption kinetics hamper its practical application. In our present report, we successfully introduce CoNiB nanoparticles as catalysts to improve the dehydrogenation performances of the 2LiBH₄/MgH₂ composite. The sample with CoNiB additives shows a significant desorption property. Temperature programmed desorption (TPD) measurement demonstrates that the peak decomposition temperatures of MgH₂ and LiBH₄ are lowered to be 315 °C and 417 °C for the CoNiB-doped 2LiBH₄/MgH₂. Isothermal dehydrogenation analysis demonstrates that approximately 10.2 wt% hydrogen can be released within 360 min at 400 °C. In addition, this study gives a preliminary evidence for understanding the CoNiB catalytic mechanism of 2LiBH₄/MgH₂     

Hydrogen storage performance of LiBH4+1/2MgH2 composites improved by Ce-based additives

LiBH₄+1/2MgH₂ is a promising reactive hydride composite for hydrogen storage. In the present study, three Ce-based additives were used as catalysts to enhance the hydrogen storage performance of LiBH₄+1/2MgH₂ composites. The composites with Ce additives demonstrated significantly improved dehydrogenation kinetics and cyclic stability compared with the pure composite. X-ray diffraction and scanning electron microscopy analyses clearly revealed the phase transitions and morphological evolution during the hydriding-dehydriding cycling. The composites with Ce-based additives displayed stable nanostructures, in contrast to the rapid microstructural deterioration in the uncatalyzed composite. The CeB₆ formed in the composites had a particle size of 10 nm after five cycles. It may act as the nucleus for MgB₂ formation during dehydrogenation and thus account for the structural and performance stability of the composites upon cycling.