Sliding Wear Behavior of HVOF-sprayed Cr3C2–NiCr/CeO2 Composite Coatings at Elevated Temperature up to 800 °C

Four types of Cr₃C₂–NiCr coatings containing different fractions of CeO₂ additive were deposited using high velocity oxy-fuel spraying. Hardness tester, X-ray diffractometer, contact surface profiler, and scanning electron microscope equipped with energy dispersive spectrometer were employed to characterize the microhardness, phase composition, surface roughness, and microstructure of as-sprayed coatings. At the same time, the friction and wear behavior of the as-sprayed coatings sliding against Si₃N₄ ball at room temperature and elevated temperature of 400 or 800 °C under unlubricated condition was evaluated using an oscillating friction and wear tester. The worn surfaces of the composite coatings and Si₃N₄ counterpart balls were analyzed by means of scanning electron microscopy, X-ray diffraction, and three dimensional non-contact surface profiler. The friction and wear mechanisms of the coatings with and without CeO₂ additive were comparatively discussed. Results show that the composite coatings doped with CeO₂ had better wear-resistance than that without CeO₂, and the coating containing 4 wt% CeO₂ showed the best wear-resistant property. The improved wear-resistant properties of the composite coatings doped with CeO₂ were attributed to the refined microstructure and improved mechanical properties induced by CeO₂.     

Effect of Aramid Pulp and Lapinas Fiber on the Friction and Wear Behavior of NBR Powder–Modified Phenolic Resin Composite

Short fiber reinforcement plays a definite role in governing the performance of a composite through the improvement of different material properties. The present investigation deals with the effect of aramid pulp and lapinas fiber on the friction and wear characteristics of a composite made from phenolic resin modified by powdered acrylonitrile butadiene rubber (NBR) on a pin-on-disc tribometer. Four composites, containing 10, 20, 30, and 40 wt% of aramid pulp with respect to phenolic resin content, were prepared. Another four composites, containing 50, 100, 200, and 300 wt% of lapinas fiber with respect to phenolic resin content, were also made. It was found that the two different fibers have distinctly different contributions to the friction and wear properties of the composites. It was also found that the incorporation of aramid pulp enhances friction stability of the composites much better than that of lapinas fiber. The change in surface morphology of these composites was studied by scanning electron microscopy (SEM) before and after the friction test. SEM images of friction samples containing aramid pulp corroborated the occurrence of wear through an adhesive wear mechanism, whereas the lapinas fiber–containing composites showed an abrasive wear mechanism.     

Role of Third Bodies in Friction and Wear of Cold-Sprayed Ti and Ti–TiC Composite Coatings

Titanium (Ti) and Ti-based alloy wear performance is often poor unless coating or lubricants are used. An alternative is to use hard phase reinforcement. Cold spray is a relatively new method to deposit composite coatings, where here we report the deposition of a Ti–TiC coating and its sliding wear behavior. Mixtures of mechanically blended Ti–TiC with various TiC content were injected into a de Laval nozzle and sprayed onto substrates. Two composite coatings and a pure Ti coating are reported here, where the as-sprayed compositions of the composites were 13.8 and 33.4 vol% TiC. Reciprocating dry sliding wear was performed using a custom-built in situ tribometer. All tests were conducted with a sliding speed of 3 mm/s and at a normal load of 0.5 N. Using a transparent sapphire hemisphere of 6.25 mm as counterface, dynamic behavior of third bodies was directly observed. It was found that adhesive transfer of Ti was the primary wear mechanism for the Ti coating, with oxidative and abrasive wear also occurring for longer sliding cycles. The superior wear resistance of the composite coatings compared to Ti was related to dual function of TiC particles, where they reinforced the Ti matrix and facilitated the formation of a stable and protective tribofilms. The tribofilms contained carbonaceous material that provided easier shear and lower friction. The formation of these tribofilms was highly dependent on the TiC particles, which contained excess carbon compared to the equilibrium composition. Higher TiC content was more effective in quickly developing and sustaining the tribofilms.     

Friction and Wear Phenomena of Vegetable Oil–Based Lubricants with Additives at Severe Sliding Wear Conditions

The tribological responses of palm oil and soybean oil, combined with two commercial antiwear additives (zinc dialkyl dithiophosphate and boron compound), were investigated at a lubricant temperature of 100°C and under severe contact conditions in a reciprocating sliding contact. The friction coefficient of palm oil with zinc dialkyl dithiophosphate was closest to the commercial mineral engine oil, with a 2% difference. The soybean oil with zinc dialkyl dithiophosphate produced a 57% improvement in wear resistance compared to its pure oil state. The existence of boron nitride in vegetable oils was only responsive in reduction of wear rather than friction. The response of commercial antiwear additives with vegetable oils showed a potential for the future improvement in the performance of vegetable oils.     

Ionic Liquids as Lubricants of Titanium–Steel Contact. Part 2: Friction, Wear and Surface Interactions at High Temperature

The tribological behaviour and surface interactions of titanium sliding against AISI 52100 steel have been studied at 200 and 300 °C in the presence of two commercial imidazolium room temperature ionic liquid (ILs): 1-octyl-3-methylimidazolium tetrafluoroborate (L108) and 1-hexyl-3-methylimidazolium hexafluorophosphate (LP106). L108 presents the higher thermal stability but gives higher friction coefficients and wear rates than LP106, with long running-in periods and high friction values, both at 200 and 300 °C. Friction and wear rates for LP106 are lower and decrease as the temperature increases from 25 to 200 °C. At 200 °C, LP106 shows a constant friction coefficient, without running-in, produces a mild wear on titanium and no surface damage on steel. LP106 fails at 300 °C, close to its degradation temperature, due to tribochemical decomposition through partial dissociation of the hexafluorophosphate anion, with formation of a phosphorus-rich layer on the steel ball, while the titanium wear track surface is heterogeneous, showing regions with the presence of fluoride and others with the presence of phosphate. When the steel ball is substituted for a ruby sphere under the same conditions at 300 °C, a low friction coefficient and mild wear is observed, due to the higher stability of the LP106 lubricant at the ruby–titanium interface. The friction coefficients, wear mechanisms and surface interactions have been studied by means of friction-distance records, SEM, EDX and XPS.     

Dry Sliding Wear Behavior of Titanium–(TiB+TiC) in situ Composite Developed by Spark Plasma Sintering

The present study provides insight into the dry sliding wear behavior of Ti-(TiB+TiC) in situ composite. The composite was developed from a Ti-B₄C powder mixture in three different proportions. The evolution of the morphology and in situ phase formation were characterized using optical microscopy, X-ray diffraction, scanning electron microscopy (SEM), and energy-dispersive spectroscopy (EDS). The sintered Ti-(TiB+TiC) composite showed an improved hardness and wear resistance with increasing TiB and TiC particulates. The friction and wear characteristics of the Ti-(TiB+TiC) composite were investigated using a pin-on-disc tester and were evaluated using SEM and EDS.     

Tribological Properties and Wear Mechanisms of NiCr–Al2O3–SrSO4–Ag Self-Lubricating Composites at Elevated Temperatures

NiCr–Al₂O₃–SrSO₄–Ag self-lubricating composites were prepared by powder metallurgy method and the tribological properties of composites were evaluated by a ball-on-disk tribometer against alumina ball at wide temperature range from the room temperature to 1,000 °C in air. The linear coefficient of thermal expansion was evaluated for investigation of thermal stability of composites. The tribo-chemical reaction films formed on the rubbing surfaces and their effects on the tribological properties of composites at different temperatures were addressed according to the surface characterization by SEM, XRD, and XPS. The results show that the NiCr–Al₂O₃ composite with addition of 10 wt% SrSO₄ and 10 wt% Ag exhibits satisfying friction and wear properties over the entire temperature range from room temperature to 1,000 °C. The composition of the tribo-layers on the worn surfaces of the composites is varied at different temperatures. The synergistic lubricating effect of SrAl₄O₇, Ag, and NiCr₂O₄ lubricating films formed on worn surfaces were identified to reduce the friction coefficient and wear rate from room temperature to 800 °C. Meanwhile, at 1,000 °C, the SrCrO₄ and NiAl₂O₄ was formed on the worn surfaces during sliding process, combining with the NiCr₂O₄, Al₂O₃, Cr₂O₃, Ag, and Ag₂O, which play an important role in the formation of a continuous lubricating film on the sliding surface.     

Friction and Wear Properties of ZrO2�CAl2O3 Composite with Three Layered Structure Under Water Lubrication

Zirconia?CAlumina (ZrO₂?CAl₂O₃) composite with three layered structure was prepared, and its friction and wear properties under water lubrication were investigated. The results indicate that the layered composite exhibited better tribological properties comparing with ZrO₂?CAl₂O₃ mono-layered composite at same tested conditions. Good combination of toughness and strength as well as subsequently excellent friction and wear properties were mainly contributed to the residual stress of the layered composite, which caused by thermal mismatch of sintering between layers through special design of compositions and structure. Friction coefficient and wear rate of the layered composite decreased with increment of load and/or velocity. The change of tribological properties was also relative to wear mechanisms, micro-cutting, and abrasive wear were main mechanisms at lower load and/or lower velocity but fatigue wear caused by plastic deformation became dominant at higher load and/or higher velocity.     

Formation of Laminar Structure Under Unlubricated Friction of Cu–SiO2 Composite

A laminar-structured tribolayer on the worn surface of Cu?CSiO₂ composite in sliding against 1045 steel is observed by etching the longitudinal sections. In morphology, the tribolayer consists of many subunits with different lengths and heights. The subunits are curved or parallel to the contact surface at different depths from bulk to the worn surface. In microstructure, the tribolayer is unconsolidated after etching, and fine Cu grains, as well as few fractured SiO₂ particles, are observed. The main formation mechanism of the laminar-structured tribolayer is grain boundary sliding. Shear localization with large plastic strain is a prerequisite for the formation of laminar structure. The generation and accumulation of frictional heating promote the plastic deformation and decrease the activation energy for grain boundary sliding. The etching effect is contributed to the presentation of the laminar structure.     

Influence of Polyfluo-Wax on the Friction and Wear Behavior of Polyimide/Epoxy Resin–Molybdenum Disulfide Bonded Solid Lubricant Coating

Polyimide/Epoxy resin–molybdenum disulfide bonded solid lubricant coatings (denoted as PI/EP-MoS₂) were prepared. The influence of polyfluo-wax (denoted as PFW) on the microhardness and friction and wear behavior of as-prepared PI/EP-MoS₂ lubricant coating was measured using a microhardness tester and a reciprocating ball-on-disc tribometer, respectively. The worn surfaces of the lubricant coatings were observed with a scanning electron microscope, and their wear rate was determined with a Micro XAM surface mapping microscope. Moreover, the transfer films formed on the counterpart steel ball surfaces were analyzed by X-ray photoelectron spectroscopy. Results indicate that the incorporation of a proper content of PFW filler is effective at improving the antifriction performance of the PI/EP-MoS₂ lubricant coating while maintaining better wear resistance. Moreover, the friction coefficient of the lubricant coating decreases with increasing content of PFW from 2 to 10%, and the one with a filler content over 6% PFW has a steady friction coefficient of 0.07. The improvement in the antifriction performance of the lubricant coating with the incorporation of the PFW filler is attributed to the excellent lubricity of homogeneously distributed PFW.     

Dry Reciprocating Sliding Friction and Wear Response of WC–Ni Cemented Carbides

A number of WC–Ni based cemented carbide grades with distinctive binder contents were tested with the goal to evaluate their dry reciprocating sliding friction and wear behaviour against WC–6 wt.%Co cemented carbide using a Plint TE77 tribometer and distinctive normal contact loads. The generated wear tracks were analysed by scanning electron microscopy and quantified volumetrically using surface scanning topography. The experimental results revealed one WC–Ni grade with superior wear performance.     

The Elevated Temperature Wear Analysis of Laser Surface–Hardened EN25 Steel Using Response Surface Methodology

The wear behavior of as-received and laser-hardened EN25 low-alloy steel is performed in dry sliding condition using a pin-on-disc-type machine. A response surface methodology–based Box-Behnken design is used to design the experimental matrix by reducing the number of experimental conditions and to develop mathematical models between the key process parameters. The process parameters considered are applied load, temperature, and sliding distance and the responses are wear rate and coefficient of friction. Analysis of variance is used to analyze the developed model. Laser surface–hardened samples exhibit a lower wear rate (0.099 × 10³to 0.490 × 10³mm³/m) and coefficient of friction (0.080 to 0.245 μ) compared to as-received samples.     

Tribological Behavior of WC-12Co Air Plasma–Sprayed Coating at Elevated Temperatures

The friction and wear performance of WC-12Co air plasma–sprayed (APS) coating at temperatures of 25–650°C under loads of 8 and 28 N in at atmospheric environment have been studied by a ball-on-disc tribometer. The effect of temperature and load on the tribological behavior of WC-Co coating was investigated. The results show that under a load of 8 N, the wear volume of the coating increases at 250°C due to the coating splat delamination and then it gradually decreases at 350–500°C. The friction could promote the formation of double oxide (CoWO₄), which is beneficial to reduce friction and wear. At higher temperatures, the wear volume increases again due to the removal of oxides. Under a load of 28 N, the wear volume of the coating increases enormously at 250°C due to the serious splat delamination. At 350°C, the load promotes double oxide formation, resulting in an early decrease in the coefficient of friction and a rapid reduction in wear volume. Although the wear volume decreases at 350–500°C, it is 10-fold higher than that under a load of 8 N. Above 500°C, the differences of the wear volumes of coatings under the two loads become less obvious, and similar trends also appear for the coefficients of friction. The synergistic effect between the load and temperature on the friction and wear mechanism of WC-12Co APS coating is discussed.     

The Friction and Wear Properties of Ti–Al–Nb Intermetallics by Plasma Surface Alloying

Both plasma chromizing and carburization following plasma chromizing (duplex treatment) for Ti–Al–Nb alloy were performed, respectively, and the microstructure, dynamic ultra-microhardness, and elastic modulus of the alloying layer were determined. Using silicon nitride (Si₃N₄) balls as the counterface materials, dry sliding friction tests on the substrate, the chromized layer, and the duplex-treated layer were completed by ball-on-disk tribometer at room temperature. The results indicated that the duplex-treated layer was mainly composed of Cr₂₃C₆, Cr₂Nb, pure chromium, and carbon phases, while the chromized layer consisted of Al₈Cr₅ and Cr₂Nb phases. The ultra-microhardness of the duplex-treated layer was higher than that of the chromized layer, whereas the elastic modulus of the duplex-treated layer was lower than that of the chromized layer. The friction coefficient of the duplex-treated layer was about three times lower than that of the chromized layer, while the wear rate was one order of magnitude lower than that of the chromized layer.     

Wear Behavior of (TiB2–TiC)–Ni/TiAl/Ti Gradient Materials Prepared by the FAPAS Process

(TiB₂–TiC)–Ni/TiAl/Ti functionally gradient materials were prepared by field-activated pressure-assisted synthesis processes. (TiB₂–TiC)–Ni composite ceramic, the top layer of the functional gradient materials, was prepared in situ by the combustion synthesis process using Ti and B₄C powders as raw materials. Scanning electron microscope (SEM) images of the ceramic layer revealed that the TiB₂ and TiC particles in the composite were fine and homogeneously dispersed in the Ni matrix. The friction and wear properties of the (TiB₂–TiC)–Ni ceramic were evaluated by sliding against a GCr15 disk at temperatures from ambient up to 400 °C. The experimental results showed that the friction coefficient of the (TiB₂–TiC)–Ni ceramic decreased with the increasing testing temperature, load, and sliding speed. However, the loss rate decreased at higher temperature and increased at higher load and higher sliding speed. The wear mechanisms of (TiB₂–TiC)–Ni ceramic mainly depend upon thermal oxidation at higher temperature, load, and sliding speed. The worn topography and phase component of the worn surfaces were analyzed using SEM, energy dispersive spectroscopy, and X-ray diffraction. The oxide films of Fe₂O₃, TiO₂, and B₂O₃ formed during the friction process play an important role in lubrication, which results in a smaller friction coefficient.     

Wear of the Counterbody at the Research Friction on Carbon Coating–Orientant in Lubricant Environments

The profile wear scars on steel balls are analyzed upon their friction in lubricant against steel coated with monocrystalline carbon doped by tungsten. Bond of ball wear with the lubricant composition and the range of test loads has been established.     

The Microstructure and Wear Characteristics of Cu–Fe Matrix Friction Material with Addition of SiC

The Cu–Fe matrix continuous braking friction materials using SiC as abrasive were fabricated by powder metallurgy technique, and the effect of content and size of SiC were investigated. The tribological properties of friction materials sliding against AISI 1045 steel ring were carried out on a block-on-ring tester at different loads and sliding speeds. The strengthening effect of nano-SiC (55 nm) was superior to that of micro-SiC (70 μm) of the tribological properties for friction materials. The friction coefficients of friction materials increased with increasing nano-SiC content. However, the wear rates decreased with increasing nano-SiC content and then increased when the content of nano-SiC particle exceeded 10 wt%. The specimen contained 10% nano-SiC had the best tribological properties at different testing conditions.     

Advanced Tribometer for In Situ Studies of Friction, Wear, and Contact Condition—Advanced Tribometer for Friction and Wear Studies

An advanced ball-on-disk tribometer was developed for in situ studies of friction, wear, and contact condition during sliding. Kinetic friction force, contact resistance (R _c), acoustic emission (AE), ball position perpendicular () to the plane of the disk (ball and disk wear), and disk surface reflectance (disk wear) were all measured simultaneously during sliding experiments. Metal (440C steel) balls were slid against ceramic (n-doped polysilicon) wafers at light load (10g) and short test duration (2.5min). Significant changes in measured parameters were observed as sliding progressed. These changes are discussed, and when considered together provide new insights into friction and wear mechanisms not readily obtainable from more standard tribometers. The effects of disk run-out (effective surface waviness) on and R _c were also investigated. Friction and R _c were periodic with a period equal to the period of disk rotation. The behavior was complex, but generally going up a hill increased and decreased R _c, with the opposite behavior going down a hill. We established a critical link between low-frequency friction oscillations (LFFO) and the nature of the contact between sliding surfaces (R _c measurement). The geometric ratchet mechanism was ruled out as a cause of LFFO, as the surface slope was too small to explain the large friction oscillations. Coating the balls and wafers with lower friction materials resulted in negligible LFFO, which makes it unlikely that LFFO were simply a result of an oscillating normal force created by dynamic effects. LFFO likely have their origins in the complex nature of the contact between rubbing surfaces.     

Hysteresis Behavior in the Stick–Slip Mode at the Boundary Friction

A tribological system is considered that consists of two atomically smooth solid surfaces separated by an ultrathin lubricant film. A thermodynamic model based on the Landau theory of phase transitions is built that describes the behavior of this system in the boundary friction mode. The free energy density for an ultrathin lubricant film is given in the form of expansion in series in terms of the powers of order parameter that is reduced to the shear modulus of the lubricant. The kinetics of the system is studied on the basis of a model describing first-order phase transitions between kinetic modes of friction. It is shown that in the presence of spring between the external drive and block the width of temperature hysteresis increases versus fixed coupling.