Attempts to reduce NOx exhaust emissions by using reformulated biodiesel

Biodiesel is a renewable, domestically produced fuel that has been shown to reduce particulate, hydrocarbon, and carbon monoxide emissions from diesel engines. Under some conditions, however, biodiesel produced from certain feedstocks has been shown to cause an increase in nitrogen oxides (NO_x). This is of special concern in urban areas that are subject to strict environmental regulations. Although soy-based biodiesel may increase the emission of nitrogen oxides, it is the most easily accessible in North America. We investigated two routes to reformulate soy-based biodiesel in an effort to reduce nitrogen oxide emissions. In one of these, soy-oil methyl esters were modified by conversion of a proportion of the cis bonds in the fatty acid chains of its methyl esters to their trans isomers. In the other approach, polyol derivatives of soybean oil were transesterified to form soy methyl polyol fatty acid esters. The NO_x emissions of these modified biodiesels were then examined, using a Yanmar L100 single cylinder, four stroke, naturally aspirated, air cooled, direct injection diesel engine. Using either isomerized methyl oleate or isomerized soy biodiesel, at 20% blend level in petroleum diesel (‘B20’), nitrogen oxide emissions were elevated by between 1.5 and 3 percentage points relative to the combustion of a B20 blend of commercial biodiesel. Nitrogen oxide emissions were reduced in proportion to blend level during the combustion of polyol biodiesel, with a 20% blend in petrodiesel resulting in a reduction of about 4.5 percentage points relative to the emissions of a comparable blend of commercial soy biodiesel.     

Evaluation of partially hydrogenated methyl esters of soybean oil as biodiesel

Biodiesel, an alternative fuel derived from vegetable oils or animal fats, continues to undergo rapid worldwide growth. Specifications mandating biodiesel quality, most notably in Europe (EN 14214) and the USA (ASTM D6751), have emerged that limit feedstock choice in the production of biodiesel fuel. For instance, EN 14214 contains a specification for iodine value (IV; 120 g I₂/100 g maximum) that eliminates soybean oil as a potential feedstock, as it generally has an IV >120. Therefore, partially hydrogenated soybean oil methyl esters (PHSME; IV = 116) were evaluated as biodiesel by measuring a number of fuel properties, such as oxidative stability, low‐temperature performance, lubricity, kinematic viscosity, and specific gravity. Compared to soybean oil methyl esters (SME), PHSME were found to have superior oxidative stability, similar specific gravity, but inferior low‐temperature performance, kinematic viscosity, and lubricity. The kinematic viscosity and lubricity of PHSME, however, were within the prescribed US and European limits. There is no universal value for low‐temperature performance in biodiesel specifications, but PHSME have superior cold flow behavior when compared to other alternative feedstock fuels, such as palm oil, tallow and grease methyl esters. The production of PHSME from refined soybean oil would increase biodiesel production costs by US$ 0.04/L (US$ 0.15/gal) in comparison to SME. In summary, PHSME are within both the European and American standards for all properties measured in this study and deserve consideration as a potential biodiesel fuel.     

Exhaust emissions and fuel properties of partially hydrogenated soybean oil methyl esters blended with ultra low sulfur diesel fuel

Important fuel properties and emission characteristics of blends (20 vol.%) of soybean oil methyl esters (SME) and partially hydrogenated SME (PHSME) in ultra low sulfur diesel fuel (ULSD) were determined and compared with neat ULSD. The following changes were observed for B20 blends of SME and PHSME versus neat ULSD: improved lubricity, higher kinematic viscosity and cetane number, lower sulfur content, and inferior low-temperature properties and oxidative stability. With respect to exhaust emissions, B20 blends of PHSME and SME exhibited lower PM and CO emissions in comparison to those of neat ULSD. The PHSME blend also showed a significant reduction in THC emissions. Both SME and PHSME B20 blends yielded small increases in NO_x emissions. The reduction in double bond content of PHSME did not result in a statistically significant difference in NO_x emissions versus SME at the B20 blend level. The test engine consumed a greater amount of fuel operating on the SME and PHSME blends than on neat ULSD, but the increase was smaller for the PHSME blend.     

Biodiesel from safflower oil and its application in a diesel engine

Safflower seed oil was chemically treated by the transesterification reaction in methyl alcohol environment with sodium hydroxide (NaOH) to produce biodiesel. The produced biodiesel was blended with diesel fuel by 5% (B5), 20% (B20) and 50% (B50) volumetrically. Some of important physical and chemical fuel properties of blend fuels, pure biodiesel and diesel fuel were determined. Performance and emission tests were carried out on a single cylinder diesel engine to compare biodiesel blends with petroleum diesel fuel. Average performance reductions were found as 2.2%, 6.3% and 11.2% for B5, B20 and B50 fuels, respectively, in comparison to diesel fuel. These reductions are low and can be compensated by a slight increase in brake specific fuel consumption (Bsfc). For blends, Bsfcs were increased by 2.8%, 3.9% and 7.8% as average for B5, B20 and B50, respectively. Considerable reductions were recorded in PM and smoke emissions with the use of biodiesel. CO emissions also decreased for biodiesel blends while NO_x and HC emissions increased. But the increases in HC emissions can be neglected as they have very low amounts for all test fuels. It can be concluded that the use of safflower oil biodiesel has beneficial effects both in terms of emission reductions and alternative petroleum diesel fuel.     

Various strategies for reducing Nox emissions of biodiesel fuel used in conventional diesel engines: A review

Energy demand, decreasing fossil fuel reserves, and health-related issues about pollutants have led researchers to search for renewable alternative fuels to either partially or fully replace fossil fuels. Among many alternative fuels, biodiesel became one of the most popular choices due to similar properties to that of conventional diesel. Biodiesel produces slightly lower brake thermal efficiency compared to that of conventional biodiesel, but has an advantage of reduced emissions of CO₂, CO, HC, and smoke. However, biodiesel shows higher NOx emission which, when used in increased biodiesel market, may become a serious problem. Various strategies were attempted by different researcher to reduce NOx emissions. In this paper, various strategies, adapted for reducing NOx emissions of biodiesel fuel used in diesel engines for automobile applications, are reviewed and discussed. The strategies are grouped into three major groups, namely combustion treatments, exhaust after-treatments, and fuel treatments. Among various strategies discussed, fuel treatments, such as low temperature combustion, mixing fuel additives and reformulating fuel composition, reduce NOx emission without compromising other emission and performance characteristics and they seem to be promising for future biodiesel fuel.     

Diesel engine performance and emission characteristics of biodiesel produced by the peroxidation process

Biodiesel is an alternative fuel that is cleaner than petrodiesel. Biodiesel can be used directly as fuel for a diesel engine without having to modify the engine system. It has the major advantages of having high biodegradability, excellent lubricity and no sulfur content. In this study, the biodiesel produced by a transesterification technique was further reacted by using a peroxidation process. Four types of diesel fuel, biodiesel with and without an additional peroxidation process, a commercial biodiesel and ASTM No. 2D diesel were compared for their fuel properties, engine performance and emission characteristics. The experimental results show that the fuel consumption rate, brake thermal efficiency, equivalence ratio, and exhaust gas temperature increased while the bsfc, emission indices of CO₂, CO and NO_x decreased with an increase of engine speed. The three biodiesels showed a higher fuel consumption rate, bsfc, and brake thermal efficiency, while at the same time exhibited lower emission indices of CO and CO₂ as well as a lower exhaust gas temperature when compared to ASTM No. 2D diesel. Moreover, the biodiesel produced with the additional peroxidation process was found to have an oxygen content, weight proportion of saturated carbon bonds, fuel consumption rate, and bsfc that were higher than the biodiesel produced without the additional process; while at the same time the brake thermal efficiency, equivalence ratio, and emission indices of CO₂, CO and NO_x were found to be lower. In particular, biodiesel produced with the addition of the peroxidation process had the lowest equivalence ratio and emission indices of CO₂, CO and NO_x among all of the four test fuels. Therefore, the peroxidation process can be used to effectively improve the fuel properties and reduce emissions when biodiesel is used.     

Effects of emulsification variables on fuel properties of two- and three-phase biodiesel emulsions

Biodiesel has attractive fuel properties such as excellent biodegradability and lubricity, almost no emissions of sulfur oxides, PAH and n-PAH, reduced CO₂, PM and CO emission, superior combustion efficiency, etc. However, burning of biodiesel generally produces higher levels of NO_x emissions, primarily due to its high oxygen content. In this study, the emulsification technology has been considered to reduce the NO_x emission level of fossil fuel. Biodiesel, produced by means of transesterification reaction accompanied with a peroxidation process, was emulsified to form two-phase W/O and three-phase O/W/O emulsions. The effects of the emulsification variables such as hydrophilic lipophilic balance (HLB), and water content on the fuel properties and emulsion characteristics of W/O and O/W/O emulsions were investigated in this study. The experimental results show that the surfactant mixture with HLB = 13 produced the highest emulsification stability while HLB = 6 produced the lowest emulsification stability and the most significant extent of water–oil separation among the various HLB values for O/W/O biodiesel emulsion. The kinematic viscosity, specific gravity and carbon residual of the biodiesel emulsions were larger than those of the neat biodiesel. In addition, the W/O biodiesel emulsion was found to have a smaller mean droplet size, lower volumetric fraction of the dispersed phase than the O/W/O biodiesel emulsion, and the highest heating value among the test fuels, if the water content is deducted from the calculation of the heating value.     

The production of fatty acid isopropyl esters and their use as a diesel engine fuel

Biodiesel is an alternative fuel for diesel engines that consists of the monoalkyl esters of vegetable oils or animal fats. Currently, most biodiesel consists of methyl esters, which have poor cold-flow properties. Methyl esters of soybean oil will crystallize and plug fuel filters and lines at about 0°C. However, isopropyl esters have better cold-flow properties than methyl esters. This paper describes the production of isopropyl esters and their evaluation in a diesel engine. The effects of the alcohol amount, the catalyst amount, and two different catalysts on producing quality biodiesel were studied. Both sodium isopropoxide and potassium isopropoxide were found to be suitable for use in the transesterification process. A 20∶1 alcohol/TG molar ratio and a catalyst amount equal to 1% by weight (based on the TG amount) of sodium metal was the most cost-effective way to produce biodiesel fuel. The emissions from a diesel engine running on isopropyl esters made from soybean oil and yellow grease were investigated by comparing them with No. 2 diesel fuel and methyl esters. For nitrogen oxide emission, the difference between the biodiesel produced from soybean oil and yellow grease was greater than the difference between the methyl and isopropyl esters of both feedstocks. The other emissions from using isopropyl esters were about 50% lower in hydrocarbons, 10–20% lower in carbon monoxide, and 40% lower in smoke number when compared with No. 2 diesel fuel.     

Engine performance and emission characteristics of a three-phase emulsion of biodiesel produced by peroxidation

Biodiesel, which is produced from vegetable oils, animal fats or used cooking oils, can be used as an alternative fuel for diesel engines. The high oxygen content of biodiesel not only enhances its burning efficiency, but also generally promotes the formation of more nitrogen oxides (NO_x) during the burning process. Fuel emulsification and the use of NO_x inhibitor agents in fuel are considered to be effective in reducing NO_x emissions. In the study reported herein, soybean oil was used as raw oil to produce biodiesel by transesterification reaction accompanied by peroxidation to further improve the fuel properties of the biodiesel, which was water washed and distilled to remove un-reacted methanol, water, and other impurities. The biodiesel product was then emulsified with distilled water and emulsifying surfactant by a high-speed mechanical homogenizer to produce a three-phase oil-droplets-in-water-droplets-in-oil (i.e. O/W/O) biodiesel emulsion and an O/W/O emulsion that contained aqueous ammonia, which is a NO_x inhibitor agent. A four-stroke diesel engine, in combination with an eddy-current dynamometer, was used to investigate the engine performance and emission characteristics of the biodiesel, the O/W/O biodiesel emulsion, the O/W/O biodiesel emulsion that contained aqueous ammonia, and ASTM No. 2D diesel. The experimental results show that the O/W/O emulsion has the lowest carbon dioxide (CO₂) emissions, exhaust gas temperature, and heating value, and the largest brake specific fuel consumption, fuel consumption rate, and kinematic viscosity of the four tested fuels. The increase of engine speed causes the increase of equivalence ratio, exhaust gas temperature, CO₂ emissions, fuel consumption rate, and brake specific fuel consumption, but a decrease of NO_x emissions. Moreover, the existence of aqueous ammonia in the O/W/O biodiesel emulsion curtails NO_x formation, thus resulting in the lowest NO_x emissions among the four tested fuels in burning the O/W/O biodiesel emulsion that contained aqueous ammonia.     

Physical properties of oleochemical carbonates

Carbonates are a class of compounds that have recently found increasing interest in commercial applications owing to their physical properties and relatively straightforward synthesis. In this work, physical and fuel properties of five straight-chain C_17–39 and three branched C_17–33 oleochemical carbonates were investigated. These properties included cetane number (CN), low-temperature properties, (kinematic) viscosity, lubricity, and surface tension. The carbonates studied had CN ranging from 47 to 107 depending on carbon chain length and branching. For the same number of carbons, the CN of carbonates were lower than those of FA alkyl esters owing to interruption of the CH₂ chain by the carbonate moiety. Kinematic viscosities at 40°C ranged from 4.9 to 22.6 mm²/s whereas m.p. ranged from +3 to below −50°C depending on the carbonate structure. High-frequency reciprocating rig testing showed the neat carbonates to have acceptable lubricity that improved as chain length increased. Finally, the carbonate's ability to influence cold-flow properties in biodiesel (methyl soyate) and lubricity in low-lubricity ultra-low sulfur diesel were examined. The carbonates studied did not significantly affect cold flow or lubricity properties at concentrations up to 10,000 ppm (1 wt%). The properties of the carbonates resemble those of fatty alkyl esters with similar trends resulting from compound structure.     

Evaluation of formulation strategies to eliminate the biodiesel NOx effect

In this paper, we explore the efficacy of (1) reducing the iodine value of soy-derived biodiesel fuels through increasing the methyl oleate (methyl ester of oleic acid) content and (2) addition of cetane improvers, as strategies to combat the biodiesel NO_x effect: the increase in NO_x emissions observed in most studies of biodiesel and biodiesel blends. This is accomplished by spiking a conventional soy-derived biodiesel fuel with methyl oleate or with cetane improver. The impact on bulk modulus of compressibility, fuel injection timing, cetane number, combustion, and emissions were examined. The conventional B20 blend produced a NO_x increase of 3–5% relative to petroleum diesel, depending on injection timing. However, by using a B20 blend where the biodiesel portion contained 76% methyl oleate, the biodiesel NO_x effect was eliminated and a NO_x neutral blend was produced. The bulk modulus of petroleum diesel was measured to be 2% lower than B20, yielding a shift in fuel injection timing of 0.1–0.3 crank angle. The bulk modulus of the high methyl oleate B20 blend was measured to be 0.5% lower than B20, not enough to have a measurable impact on fuel injection timing. Increasing the methyl oleate portion of the biodiesel to 76% also had the effect of increasing the cetane number from 48.2 for conventional B20 to 50.4, but this effect is small compared to the increase to 53.5 achieved by adding 1000 ppm of 2-ethylhexyl nitrate (EHN) to B20. For the particular engine tested, NO_x emissions were found to be insensitive to ignition delay, maximum cylinder temperature, and maximum rate of heat release. The dominant effect on NO_x emissions was the timing of the combustion process, initiated by the start of injection, and propagated through the timing of maximum heat release rate and maximum temperature.     

Cetane numbers of branched and straight-chain fatty esters determined in an ignition quality tester

The cetane number, a widely used diesel fuel quality parameter related to the ignition delay time (and combustion quality) of a fuel, has been applied to alternative diesel fuels such as biodiesel and its components. In this work, the cetane numbers of 29 samples of straight-chain and branched C₁-C₄ esters as well as 2-ethylhexyl esters of various common fatty acids were determined. The cetane numbers of these esters are not significantly affected by branching in the alcohol moiety. Therefore, branched esters, which improve the cold-flow properties of biodiesel, can be employed without greatly influencing ignition properties compared to the more common methyl esters. Unsaturation in the fatty acid chain was again the most significant factor causing lower cetane numbers. Cetane numbers were determined in an ignition quality tester (IQT) which is a newly developed, automated rapid method using only small amounts of material. The IQT is as applicable to biodiesel and its components as previous cetane-testing methods.     

Biodiesel engine performance and emissions in low temperature combustion

Engine performance and emission comparisons were made between the use of soy, Canola and yellow grease derived B100 biodiesel fuels and an ultra-low sulphur diesel fuel in the high load engine operating conditions. Compared to the diesel fuel engine-out emissions of nitrogen oxides (NO_x), a high-cetane number (CN) biodiesel fuel produced comparable NO_x while the biodiesel with a CN similar to the diesel fuel produced relatively higher NO_x at a fixed start of injection. The soot, carbon monoxide and un-burnt hydrocarbon emissions were generally lower for the biodiesel-fuelled engine. Exhaust gas recirculation (EGR) was then extensively applied to initiate low temperature combustion (LTC) mode at medium and low load conditions. An intake throttling valve was implemented to increase the differential pressure between the intake and exhaust in order to increase and enhance the EGR. Simultaneous reduction of NO_x and soot was achieved when the ignition delay was prolonged by more than 50% from the case with 0% EGR at low load conditions. Furthermore, a preliminary ignition delay correlation under the influence of EGR at steady-state conditions was developed. The correlation considered the fuel CN and oxygen concentrations in the intake air and fuel. The research intends to achieve simultaneous reductions of NO_x and soot emissions in modern production diesel engines when biodiesel is applied.     

Biodiesel production from tall oil with synthesized Mn and Ni based additives: Effects of the additives on fuel consumption and emissions

In this study, biodiesel fuel and fuel additives were produced from crude tall oil that is a by-product in the pulp manufacturing by craft or sulphate pulping process. Fatty acids and resinic acids were obtained from crude tall oil by distillation method. Tall oil methyl ester (biodiesel) was produced from fatty acids. Resinic acids were reacted with NiO and MnO₂ stoichiometrically for production of metallic fuel additives. Each metallic fuel additive was added at the rate of 8 μmol/l and 12 μmol/l to make mixtures of 60% tall oil methyl ester/40% diesel fuel (TE60) for preparing test fuels. Metallic fuel additives improved properties of biodiesel fuels, such as pour point and viscosity values. Biodiesel fuels were tested in an unmodified direct injection diesel engine at full load condition. Specific fuel consumption of biodiesel fuels increased by 6.00%, however, in comparison with TE60, it showed trend of decreasing with adding of additives. Exhaust emission profile of biodiesel fuels improved. CO emissions and smoke opacity decreased up to 64.28% and 30.91% respectively. Low NO_x emission was also observed in general for the biodiesel fuels.     

Preparation of fatty acid methyl esters from hazelnut,high-oleic peanut and walnut oils and evaluation as biodiesel

Refined hazelnut, walnut and high-oleic peanut oils were converted into fatty acid methyl esters using catalytic sodium methoxide and evaluated as potential biodiesel fuels. These feedstocks were of interest due to their lipid production potentials (780–1780 L ha^?1 yr^?1) and suitability for marginal lands. Methyl oleate was the principal constituent identified in hazelnut (HME; 76.9%) and peanut (PME; 78.2%) oil methyl esters. Walnut oil methyl esters (WME) were comprised primarily of methyl esters of linoleic (60.7%), oleic (15.1%) and linolenic (12.8%) acids. PME exhibited excellent oxidative stability (IP 21.1 h; EN 14112) but poor cold flow properties (CP 17.8 °C) due to its comparatively high content of very-long chain fatty esters. WME provided low derived cetane number and oxidative stability (IP 2.9 h) data as a result of its high percentage of polyunsaturated fatty esters. HME yielded a satisfactory balance between all fuel properties when compared to the biodiesel standards ASTM D6751 and EN 14214 due to its high content of monounsaturated fatty esters. Also explored were the properties of blends of HME, PME and WME in ultra-low sulfur (<15 ppm) diesel (ULSD) fuel and comparison to petrodiesel standards ASTM D975, D7467 and EN 590. With increasing content of biodiesel, the oxidative stability, cold flow properties and calorific value of ULSD was negatively affected, whereas lubricity was markedly improved. Kinematic viscosity, specific gravity and surface tension were impacted to lesser extents by addition of biodiesel to ULSD. In summary, HME, PME and WME are suitable based on their fuel properties as biodiesel fuels and blend components in ULSD.     

Performance and emission study of waste anchovy fish biodiesel in a diesel engine

Waste anchovy fish oils transesterification was studied with the purpose of achieving the conditions for biodiesel usage in a single cylinder, direct injection compression ignition. With this purpose, the pure biodiesel produced from anchovy fish oil, biodiesel-diesel fuel blends of 25%:75% biodiesel-diesel (B25), 50%:50% biodiesel-diesel (B50), 75%:25% biodiesel-diesel (B75) and petroleum diesel fuels were used in the engine to specify how the engine performance and exhaust emission parameters changed. The fuel properties of test fuels were analyzed. Tests were performed at full load engine operation with variable speeds of 1000, 1500, 2000 and 2500 rpm engine speeds. As results of investigations on comparison of fuels with each other, there has been a decrease with 4.14% in fish oil methyl ester (FOME) and its blends' engine torque, averagely 5.16% reduction in engine power, while 4.96% increase in specific fuel consumption have been observed. On one hand there has been average reduction as 4.576%, 21.3%, 33.42% in CO₂, CO, HC, respectively; on the other hand, there has been increase as 9.63%, 29.37% and 7.54% in O₂, NO_x and exhaust gas temperature has been observed. It was also found that biodiesel from anchovy fish oil contains 37.93 wt.% saturated fatty acids which helps to improve cetane number and lower NO_x emissions. Besides, for biodiesel and its blends, average smoke opacity was reduces about 16% in comparison to D2. It can be concluded that waste anchovy fish obtained from biodiesel can be used as a substitute for petroleum diesel in diesel engines.     

Dependence of biodiesel fuel properties on the structure of fatty acid alkyl esters

Biodiesel, defined as the mono-alkyl esters of vegetable oils or animal fats, is an “alternative” diesel fuel that is becoming accepted in a steadily growing number of countries around the world. Since the source of biodiesel varies with the location and other sources such as recycled oils are continuously gaining interest, it is important to possess data on how the various fatty acid profiles of the different sources can influence biodiesel fuel properties. The properties of the various individual fatty esters that comprise biodiesel determine the overall fuel properties of the biodiesel fuel. In turn, the properties of the various fatty esters are determined by the structural features of the fatty acid and the alcohol moieties that comprise a fatty ester. Structural features that influence the physical and fuel properties of a fatty ester molecule are chain length, degree of unsaturation, and branching of the chain. Important fuel properties of biodiesel that are influenced by the fatty acid profile and, in turn, by the structural features of the various fatty esters are cetane number and ultimately exhaust emissions, heat of combustion, cold flow, oxidative stability, viscosity, and lubricity.     

Effects of NOx-inhibitor agent on fuel properties of three-phase biodiesel emulsions

Biodiesel is one of the more promising alternative clean fuels to fossil fuel, which can reduce the emissions of fossil fuel burning, and possibly resolve the energy crisis caused by the exhaustion of petroleum resources in the near future. The burning of biodiesel emits much less gaseous emissions and particulate matter primarily because of its dominant combustion efficiency. However, the high oxygen content in biodiesel not only promotes the burning process but also enhances NO_x formation when biodiesel is used as fuel. Biodiesel emulsion and the additive of NO_x-inhibitor agent are considered to reduce levels of NO_x emissions in this experimental study. The biodiesel was produced by transesterification reaction accompanied with peroxidation process. A three-phase biodiesel emulsion of oil-in water drops-in oil (O/W/O) and an O/W/O biodiesel emulsion containing aqueous ammonia were prepared afterwards. The effect of the existence of NO_x-inhibitor agent on the fuel properties and the emulsion characteristics of the O/W/O biodiesel emulsions were investigated. The experimental results show that the burning of the O/W/O biodiesel emulsion and the O/W/O biodiesel emulsion containing aqueous ammonia had larger fraction of fuel burnt and thus larger heat release than the neat biodiesel if water content is not considered for the calculation of heating value. The addition of aqueous ammonia within the dispersed phase of the O/W/O biodiesel emulsion appeared to deteriorate the emulsification characteristics. A smaller quantity of emulsion and greater kinematic viscosity were formed while a larger carbon residue and actual reaction-heat release also appeared for this O/W/O biodiesel emulsion. Aqueous ammonia in the O/W/O biodiesel emulsion produces a higher pH value as well. In addition, the number as well as the volumetric fraction of the dispersed water droplets is reduced for the O/W/O biodiesel emulsion that contains aqueous ammonia.     

Adiabatic flame temperature from biofuels and fossil fuels and derived effect on NOx emissions

There is currently a sustained interest in biofuels as they represent a potential alternative to petroleum derived fuels. Biofuels are likely to help decrease greenhouse gas emissions and the dependence on oil resources. Biodiesels are Fatty Acid Methyl Esters (FAMEs) that are mainly derived from vegetable oils; their compositions depend on the parent vegetables: rapeseed (“RME”), soybean (“SME”), sunflower, palm etc. A fraction of biodiesel has also an animal origin (“tallow”). A key factor for the use of biofuels in gas turbines is their emission indices (NOx, CO, VOC, and PM) in comparison with those of conventional “petroleum gasoils”. While biodiesels reduce carbon-containing pollutants, experimental data from diesel engines show a slight increase in NOx. The literature relating to gas turbines is very scarce. Two recent, independent field tests carried out in Europe (RME) and in the USA (SME) showed slightly lower NOx while a lab test on a microturbine showed the opposite effect. To clarify the NOx index of biodiesels in gas turbines, a study has been undertaken, taking gasoil and natural gas (NG) as reference fuels. In this study, a calculation of the flame temperature developed by the 3 classes of fuels has been performed and the effect of their respective compositions has been investigated. The five FAMEs studied were RME, SME and methyl esters of sunflower, palm and tallow; these are representative of most widespread vegetable and animal oil bases worldwide. The software THERGAS has been used to calculate the enthalpy and free energy properties of the fuels and GASEQ for the flame temperature (T_f), acknowledging the fact that “thermal NOx” represents the predominant form of NOx in gas turbines. To complete the approach to structural effects, we have modeled two NG compositions (rich and weak gases) and three types of gasoil using variable blends of eleven linear/branched/cyclic molecules. The results are consistent with the two recent field tests and show that the FAMEs lie close to petroleum gasoils and higher than NG in terms of NOx emission. The composition of the biodiesel and regular diesel fuel influences their combustion heat: methyl esters with double bonds see a slight increase of their T_f and their NOx index while that of gasoil is sensitive to the aromatic content.     

Flame temperature analysis of biodiesel blends and components

Meeting sustainable energy demand with minimum environmental impact is a major area of concern in the energy sector. Alternative fuels such as biodiesel, ethanol etc. have been quite promising for fulfilling both these aspects. While biodiesel reduces emissions of CO, life cycle CO₂, SO_x, volatile organic compounds (VOC) and particulate matter (PM) significantly, the propensity for the production of NO_x is an important problem that requires extensive research. NO_x emission from a direct-injection diesel engine is mainly due to formation of thermal NO that is described by Zeldovich mechanism. Thus, studying temperature profile during biodiesel combustion can provide useful insights to the formation and destruction of NO_x. The main objective of this work is to investigate the effect of component methyl esters of biodiesel on open air flame temperature distribution and the effect of blending biodiesel with diesel and oxygenates (ethanol and methyl acetate) on open air flames. This objective was achieved by obtaining thermocouple measurements and thermal infrared imaging of local flame temperatures of wick-generated open air flames. A relationship between blend proportions and relative flame temperatures were obtained. In general, it was found that blending oxygenates such as ethanol and methyl acetate into petroleum diesel tended to increase the flame temperature in comparison with straight diesel fuel. The analyses of relative flame temperatures of different components of biodiesel were performed to evaluate the effect of unsaturation level and the hydrocarbon chain length on the flame temperature. It was found that the saturated methyl esters resulted in greater flame temperatures in comparison to unsaturated methyl esters. It was also revealed that shorter chained fatty acid methyl esters lead to higher flame temperatures as compared to its longer chained counterparts.