首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到18条相似文献,搜索用时 125 毫秒
1.
偏转磁芯铁氧体材料的磁滞损耗分析   总被引:5,自引:2,他引:3  
对偏转磁芯所采用的铁氧体材料的磁滞损耗特性进行了分析,得出了磁滞损耗功率与频率,磁通密度和温度的经验公式,对磁滞回线中涡流的影响进行分析,得出了在目前应用的偏转频率下,磁芯损耗中磁滞损耗占主要部分,根据经验公式,对计算磁否损耗的方法和计算温度分布中的应用进行了介绍。  相似文献   

2.
通过空间磁场和感应电压的测量,对偏转磁芯中的磁通密度分布进行了计算,并根据磁滞损耗的经验公式对Philips17英寸CMT的磁滞损耗进行了估测。该方法适用于降低能量损耗的偏转系统磁芯结构的优化和磁性材料的选择等。  相似文献   

3.
通过空间磁场和感应电压的测量 ,对自会聚偏转系统偏转磁芯中的二极场、六极场磁通密度的分布进行了计算 ,并根据磁滞损耗的经验公式对Philips 17英寸CMT的磁滞损耗进行了估测。该方法适用于估测高次谐波场对磁滞损耗的影响 ,降低能量损耗的偏转系统磁芯结构的优化 ,磁性材料的选择等。  相似文献   

4.
自会聚偏转系统中磁滞损耗的估测   总被引:1,自引:0,他引:1  
通过空间磁场和感应电压的测量,对自会聚偏转移系统偏转磁芯中的二极场、六极场磁通密度的分布进行了计算,并根据磁滞损耗的经验公式对Philips 17英寸CMT的磁滞损耗进行了估测。该方法适用于估测高次谐波场对磁滞损耗的影响,降低能量损耗的偏转系统磁芯结构的优化,磁性材料的选择等。  相似文献   

5.
偏转磁芯中磁滞损耗的估测   总被引:3,自引:1,他引:2  
通过空间磁场和感应电压的测量,对偏转磁芯中的磁通密度分布进行了教育处,并根据磁滞损耗的经验公式对Philips17英寸CMT的磁滞损耗进行了估测,该方法适用于降低能量损耗的偏转系统磁芯结构的优化和磁性材料的选择等。  相似文献   

6.
本文通过对偏转磁芯用的铁氧体材料的磁滞损耗特性的分析 ,提出了通过改变偏转磁芯外表面形状以减小磁滞损耗的方法。优化计算结果表明 ,对于Philips 17″CMT的 3C2材料 5mm壁厚的磁芯 ,改用椭圆外表面的磁芯后 ,磁滞损耗降低了 2 7 5 %。  相似文献   

7.
应用EMAS(Electronic MagneticFieldAnalysisSystem)和DUEMAS软件对偏转磁芯材料的磁导率对偏转系统的影响进行了计算分析。计算结果表明 ,当磁性材料的相对磁导率大于 30 0时 ,磁导率对偏转电流的影响小于 0 6 % ,对磁滞损耗的影响小于 1% ,因此在磁性材料的选择中不必过分要求高的磁导率 ,而应在降低磁滞损耗上努力。  相似文献   

8.
本通过对偏转磁芯用的铁氧体材料的磁滞损耗特性的分析,提出了通过改变偏转磁芯外表面形状以减小磁滞损耗的方法。优化计算结果表明,对于Philips 17″CMT的3C2材料5mm壁厚的磁芯,改用椭圆外表面的磁芯后,磁滞损耗降低了27.5%。  相似文献   

9.
应用EMAS和DUEMAS软件对偏转磁芯材料的磁导率对偏转系统的影响进行了计算分析。计算结果表明,当磁性材料的相对磁导率大于300时,磁导率对偏转电流的影响小于0.6%,对磁滞损耗的影响小于1%,因此在磁性材料的选择中不必过分要求高的磁导率,而应在降低磁滞损耗上努力。  相似文献   

10.
李发长  李一  柳学全  贾成厂  李楠  霍静  李金普 《功能材料》2012,43(18):2488-2491
研究了铁粉纯度和粒径对磷化铁粉软磁复合材料磁性能的影响。结果表明,铁粉经磷化后,表面成功包覆了完整均匀的磷酸盐绝缘层。铁粉纯度提高,软磁复合材料磁芯的密度和磁导率增大,同时磁滞损耗降低。铁粉粒度增大,磁芯密度和磁导率增加,中高频率下磁损耗明显增加,且频率越高越明显。  相似文献   

11.
在组合法计算彩色显像管偏转系统的基础上,对25英寸700线彩色显像管所用偏转线圈进行了优化设计。选取荧光屏光栅结点上的像差作为优化目标函数,选取线圈调制极上绕线密度的傅里叶展开系数作为优化参数,采用分步阻尼法优化设计出了25英寸700线彩色显像管用偏转线圈。根据实际的实验条件,绕制了25英寸700线彩色显像管用垂直偏转线圈,并与已有的25英寸同类彩色显像管所用偏转线圈进行了比较和分析。  相似文献   

12.
A ferromagnetic material can be levitated by the pinning effect of a field-cooled superconductor. This paper presents two methods for modeling this effect: 1) an approximate calculation to determine the relationship between attractive force and air gap at both room temperature and superconductive temperature (77 K) and 2) a novel way of modeling the pinning effect by a finite-element method (FEM). A comparison of analytical and FEM results with experimental results verifies the validity of the methods. The methods can be used to estimate the system's behavior when the cylindrical yoke is replaced by a ring yoke. The stiffness of the system will increase by 70% (to 5.3 N/mm) when a ring yoke with the same surface area is used instead of a cylindrical yoke.   相似文献   

13.
The baseline design for the SSC (Superconducting Super Collider) high energy booster (HEB) has dipole bending magnets with a 50-mm aperture. An analysis of the cryogenic heat load due to AC losses generated in the HEB ramp cycle is reported for this magnet. Included in this analysis are losses from superconductor hysteresis, yoke hysteresis, strand eddy currents, and cable eddy currents. The AC loss impact of 2.5 μm vs. 6 μm filament conductor is presented. A 60-mm aperture design is also investigated  相似文献   

14.
A three phase transformer test facility has been used for measuring the localized power loss and flux distribution within the core. The flux and loss distributions in the T-joint of a core with simple double overlap joints have been investigated. The flux density distribution was measured by an array of search coils wound on individual laminations, and the localized power loss was found by measuring the initial rate of temperature rise using miniature thermocouples. For measurements made in the range of flux densities from 1.1 to 1.6 T, the inner edges of the yoke and limb laminations were the highest loss areas, up to 30% higher than the mean core loss. These regions of high power loss were found to be due to a high third harmonic flux density component being present. The fundamental component of flux density tended to follow the rolling direction of both yoke and limb laminations; however, some deviation from the rolling direction was present in the case of other harmonics.  相似文献   

15.
In this work, the discharging process of the binary mixture composed of sphere and sphere-paired particles in a two-dimensional silo was studied. High-speed camera and self-developed particle tracking velocimetry (PTV) program were used to capture the flow behaviors of all particles. The key parameters of mixed flow, including coordination number, horizontal displacement and mechanical energy loss in the discharge process, were highlighted. It was found that the increase of sphere-paired particles can decrease the average coordination number of particles during the discharging process. The analysis about the loss of mechanical energy and the horizontal displacement of particles indicated that sphere-paired particles preferentially squeezed out sphere particles from fast flow field above the outlet. Moreover, an empirical formula was proposed to assess the influence of the proportion of sphere-paired particles on the discharge flow rate. Sphere-paired particles tended to hinder the discharging process, which was caused by the rotation around their centroids and the angular deflection close to angle of the hopper.  相似文献   

16.
以货车锻造钩尾框调质热处理为例, 采用实时测温技术测量加热和冷却过程中炉内不同位置和钩尾框不同部位处的温度,通过分析温度变化规律并结合试样的组织和力学性能结果,确定了锻造钩尾框批量生产的合理热处理工艺规范,验证了实时测温技术确定热处理工艺规范这种方法的可靠性和实用性.  相似文献   

17.
韩小雷  冯润平  季静  吴梓楠 《工程力学》2021,38(11):160-169
集中塑性铰模型常被用于基于构件的结构弹塑性分析,计算精度依赖于模型参数的选取,但经验公式难以表征构件受力特性与模型参数的复杂非线性关系。该研究收集低周往复加载RC梁试验数据。建立构件试验数据库,采用捏拢型(pinch Ibarra-Medina-Krawinkler,Pinch-IMK)本构建立基于深度学习的RC梁构件集中塑性铰模型参数预测模型。基于试验数据对三折线骨架特征点参数、本构滞回参数进行参数辨识,得到182组骨架特征点参数数据和91组滞回参数数据;以构件特征参数为输入,以骨架特征点参数、滞回参数为输出,建立Pinch-IMK集中塑性铰RC梁构件参数深度学习预测模型HDLM。将HDLM预测骨架特征点参数与截面分析及现有经验公式等方法的计算结果作对比,可见HDLM预测结果有更高的精度;将基于HDLM预测参数计算的滞回曲线与基于经验公式的IMK模型计算结果进行对比,可见HDLM预测滞回曲线更为准确,能够较好地表现RC梁的强度退化、刚度退化和捏拢效应。  相似文献   

18.
对内偏转彩色显像管技术进行了详细论述。分析了材料的真空放气特性对阴极寿命的影响。由于偏转线圈放在管内 ,不能用传统的管球与线圈装配程序进行装配。为了得到好的着屏和会聚质量 ,设计了特殊的装配步骤。给出了 14英寸和 2 1英寸电视机 (TVTs)用以及 2 1英寸彩色监视器 (CMTs)用内偏转管的分析测试结果。  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号