Enhanced sensing performance of flexible strain sensors prepared from biaxially stretched carbon nanotubes/polydimethylsiloxane nanocomposites

Flexible strain sensors from biaxially stretched carbon nanotubes (CNTs)/polydimethylsiloxane (PDMS) nanocomposites are fabricated in this study. It is shown that biaxial stretching promotes the homogeneous distribution and alignment of CNTs in the stretching plane, improving the sensing performance of the strain sensors. The optimized stretching ratios (SRs) of CNT/PDMS nanocomposites are determined. Compared to an unstretched CNT/PDMS-1.0 sensor (gauge factor [GF] value = 0.73, detectable range from 0 to 60%), the 1.5 wt% CNT/PDMS-1.5 sensor (SR = 1.5) exhibits enhanced strain sensitivity (GF = 2.8), a wider detectable range (0–370%) and better performance stability. The GF values of CNT/PDMS-2.0 and CNT/PDMS-2.5 sensors with SRs of 2.0 and 2.5, respectively, were 1.18 and 1.06, respectively, due to more significant conductive network reconstruction in the process of applying strain, leading to a decreasing GF. The possibility of sensors in the application of wearable electronic components is also demonstrated. The sensor shows a clear and stable signal output when different strain modes are applied, such as tensile, compressive, bending, and twisting.     

Strengthening and toughening of thermoplastic polyolefin elastomer using polypropylene‐grafted multiwalled carbon nanotubes

In this article, it is demonstrated that simultaneously strengthened and toughened nanocomposites based on polypropylene/EPDM thermoplastic elastomer (TPO) matrix can be achieved through enhanced adhesion between MWNTs and polymer matrix by using PP grafted multiwalled carbon nanotubes (MWNTs). To improve the interface between filler and matrix, MWNTs were treated with acid, or covalently linked to polypropylene. The chemical and morphological transformation of the modified MWNTs, and its effect on the morphology and mechanical properties of the composites are investigated. The strengthening and toughening mechanism is discussed regarding the structural property relationship. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Preparation,structure and properties of thermoplastic olefin nanocomposites containing functionalized carbon nanotubes

The morphology and properties of multiwalled carbon nanotube modified polypropylene (PP)/ethylene–octene copolymer blends were studied. Polypropylene chains are covalently grafted onto the surface of carbon nanotubes (CNTs) in order to improve their interaction with the polymer matrix. It is observed that functionalization of CNTs improves their dispersion and increases the interfacial bonding between CNTs and polymer matrix. The functionalized CNTs are selectively distributed in the continuous polypropylene phase. The size of the dispersed elastomer phase decreases after the addition of CNTs. Functionalized CNTs act as a nucleating agent and increase the crystallinity of the polypropylene. More importantly, an important increase in impact strength, stiffness and toughness can be achieved through introducing functionalized CNTs. Copyright © 2011 Society of Chemical Industry     

Poly(trimethylene terephthalate‐block‐tetramethylene oxide) elastomer/single‐walled carbon nanotubes nanocomposites: Synthesis,structure, and properties

Nanocomposites based on poly(trimethylene terephthalate)‐block‐poly(tetramethylene oxide) (PTT‐PTMO)‐segmented copolymer and COOH‐functionalized single‐walled carbon nanotubes (SWCNTs) were prepared by in situ polymerization method. The obtained nanocomposites were characterized by thermogravimetric analysis, scanning electron microscopy, differential scanning calorimetry (DSC), DMTA, wide‐angle x‐ray scattering (WAXS), small‐angle X‐ray scattering, and tensile testing. The nanocomposites with low SWCNTs loading (<0.5 wt %) shows uniform dispersion of CNT in polymer matrix. As the SWCNTs loading in the nanocomposites increase, the significant improvement of thermo‐oxidative stability was observed. It was found that the nanocomposites have slightly higher degree of crystallinity (determined by DSC and WAXS) of poly(trimethylene terephthalate) (PTT) hard phase than neat PTT‐PTMO copolymer. The melting point of PTT hard phase and glass transition temperature of poly(tetramethylene oxide)‐rich phase were not affected by the presence of CNTs in polymer matrix. The SWCNTs played a role as nucleating agent in PTT‐PTMO matrix, which led to increase in the crystallization rate. Tensile tests showed that the tensile strength of the nanocomposites with 0.05–0.3 wt % loading of SWCNTs have improved tensile strength in comparison to the neat PTT‐PTMO copolymer without reduction elongation at break. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Effect of carbon nanotubes functionalization on properties of their nanocomposites with polycarbonate/poly(acrylonitrile-butadiene-styrene) matrix

In this work, a comparative study evaluating the influence of different functionalization of carbon nanotubes on the properties of nanocomposites with polymeric matrix was performed. A 50/50 wt% polycarbonate (PC)/poly(acrylonitrile-butadiene-styrene) (ABS) blend was used as polymeric matrix of the nanocomposites. The comparison was made between nanocomposites reinforced with covalently functionalized multiwall carbon nanotubes (MWCNTf) and MWCNTf/nanoclay hybrid functionalization. The effect on the mechanical and morphological properties of the nanocomposites was evaluated through tensile and Izod impact tests and scanning electron microscopy and transmission electron microscopy (TEM) analyses. The thermal characterization of PC/ABS blends and nanocomposites was performed by differential scanning calorimetry (DSC). Results showed that both methods of functionalization of MWCNTs increased the stiffness and impact resistance of the nanocomposites. TEM micrographs indicated the preferred location of the reinforcements in the SAN phase of ABS. Results from DSC indicated an increase in the thermal resistance of the nanocomposites.     

Electrical, mechanical, and glass transition behavior of polycarbonate-based nanocomposites with different multi-walled carbon nanotubes

Five commercially available multi-walled carbon nanotubes (MWNTs), with different characteristics, were melt mixed with polycarbonate (PC) in a twin-screw micro compounder to obtain nanocomposites containing 0.25-3.0 wt.% MWNT. The electrical properties of the composites were assessed using bulk electrical conductivity measurements, the mechanical properties of the composites were evaluated using tensile tests and dynamic mechanical analysis (DMA), and the thermal properties of the composites were investigated using differential scanning calorimetry (DSC). Electrical percolation thresholds (p_cs) were observed between 0.28 wt.% and 0.60 wt.%, which are comparable with other well-dispersed melt mixed materials. Based on measurements of diameter and length distributions of unprocessed tubes it was found that nanotubes with high aspect ratios exhibited lower p_cs, although one sample did show higher p_c than expected (based on aspect ratio) which was attributed to poorer dispersion achieved during mixing. The stress-strain behavior of the composites is only slightly altered with CNT addition; however, the strain at break is decreased even at low loadings. DMA tests suggest the formation of a combined polymer-CNT continuous network evidenced by measurable storage moduli at temperatures above the glass transition temperature (T_g), consistent with a mild reinforcement effect. The composites showed lower glass transition temperatures than that of pure PC. Lowering of the height of the tanδ peak from DMA and reductions in the heat capacity change at the glass transition from DSC indicate that MWNTs reduced the amount of polymer material that participates in the glass transition of the composites, consistent with immobilization of polymer at the nanotube interface.     

Polypropylene/multiwall carbon nanotubes nanocomposites: Nanoindentation,dynamic mechanical,and electrical properties

Polypropylene (PP)/Multiwall carbon nanotubes (MWCNTs) nanocomposites were fabricated via melt compounding that utilizes a corotating twin‐screw extruder. Two commercially available MWCNTs, Baytubes C150P and C70P, were incorporated into PP matrix at concentration of 3 wt %. The nanocomposites samples were analyzed using scanning electron microscopy, dynamic mechanical analysis (DMA), nanoindentation test, and picoammeter. It was found that both MWCNTs types were well distributed and dispersed in the PP matrix and no agglomeration of MWCNTs was observed. The DMA analysis results showed that the incorporation of MWCNTs enhanced the storage modulus and thermal stability of the PP matrix. Whereas, nanoindentation creep results showed that the creep rate and displacement of the PP/MWCNTs nanocomposites was lower than the neat PP, in which C70P < C150P < PP. The reduction of creep rate and creep displacement was associated to the improvement of creep resistance. There were also improvements on hardness and stiffness of the nanocomposites. Additionally, the electrical resistivity of the neat PP decreased with the incorporation of MWCNTs. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45293.     

Flexible conductive poly(styrene‐butadiene‐styrene)/carbon nanotubes nanocomposites: Self‐assembly and broadband electrical behavior

Flexible conductive nanocomposites with the ability of self‐assembly into well‐ordered structures are promising multifunctional materials for energy conversion and storage devices. In this work, flexible nanocomposites based on multi‐walled carbon nanotubes (MWCNTs) and poly(styrene‐butadiene‐styrene) (SBS) were obtained by solution casting, followed by a post‐annealing treatment, during 7 days at 110 °C, to enable the self‐organization of the SBS. The impact of the MWCNTs on the self‐assembly was studied by atomic force microscopy and Small angle X‐rays scattering, and the conductivity of these nanocomposites was analyzed over the broadband frequency range, that is, 10^?1–10⁶ Hz. The results revealed that the lower MWCNTs loadings (～0.2 v %) were the most suitable to achieve a conductive network through the SBS, maintaining self‐assembled domains. These domains include hexagonally packed cylinders and alternating lamellae. Furthermore, at loadings above 1 v %, the impact of further MWCNTs addition on the conductivity was marginal over the whole frequency range and the self‐assembly tendency was progressively reduced. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46650.     

Viscoelasticity and thermal stability of poly(arylene ether nitrile) nanocomposites with various functionalized carbon nanotubes

Poly(arylene ether nitrile) (PEN) nanocomposites containing various functionalized multi‐walled carbon nanotubes (MWCNTs) were prepared through a solution‐casting method. The as‐prepared PEN nanocomposites were investigated using parallel‐plate rheometry and thermogravimetric analysis, aimed at examining the effect of surface functionalization on the dispersion of MWCNTs from the viscoelastic and thermal properties. The linear viscoelasticy results indicated that 4‐aminophenoxyphthalonitrile‐grafted MWCNTs presented better dispersion in the PEN matrix than purified and carboxylic MWCNTs because the corresponding composite showed the lowest rheological percolation threshold, which was further confirmed from scanning electron microscopy, dissolution experiments and solution rheological experiments. The thermogravimetric analysis results revealed that the presence of 4‐aminophenoxyphthalonitrile‐grafted and carboxylic MWCNTs retarded the depolymerization compared with purified MWCNTs, showing a marked increase in the temperature corresponding to a loss of 5 wt% (increased by 14–22 °C) and maximum rate of decomposition (increased by 4–8 °C). Both the state of dispersion and the surface functionalization of MWCNTs are very important to the thermal stability of the PEN matrix. Copyright © 2011 Society of Chemical Industry     

Multi-component nanocomposites of epoxy/silsesquioxane reinforced with carbon fibers and carbon nanotubes processed by resin transfer molding

ABSTRACT

In this work, an epoxy resin modified by silsesquioxane oligomers was used to produce multi-component nanocomposites reinforced with carbon fiber (CF) and multi-walled carbon nanotubes (CNT) by resin transfer molding (RTM). The combination of sonication process with the incorporation of silsesquioxane domains (i.e. increasing the degree of crosslinking of the epoxy matrix), improved the mechanical strength of the hybrid matrix and hybrid/CF/CNT nanocomposites. The multi-component nanocomposites produced by RTM presented Young modulus of 35 ± 8 GPa, tensile strength of 303 ± 41 MPa and impact strength of 1.0 ± 0.3 kJ m^?1. The results showed a significant increase in the tensile strength and impact resistance of the epoxy matrix by the incorporation of silsesquioxanes and sonication before curing of the matrices, showing the promising potential of this multi-component nanocomposite for pipelines and other structural applications.     

Morphology and mechanical property changes in compatibilized high density polyethylene/polyamide 6 nanocomposites induced by carbon nanotubes

Addition of carbon nanotubes to immiscible polymer blends with co‐continuous morphology features to improve the electrical conductivity has attracted much attention in recent years; however, less attention has been paid to the effect of carbon nanotubes on the morphology and corresponding physical properties of immiscible polymer blends with typical sea‐island morphology. In this work, therefore, functionalized multiwalled carbon nanotubes (FMWCNTs) were introduced into an immiscible high density polyethylene/polyamide 6 (HDPE/PA6) blend which was compatibilized by maleic anhydride grafted HDPE (HDPE‐MA). The distribution of FMWCNTs and the phase morphologies of the nanocomposites were characterized using scanning electron microscopy and transmission electron microscopy. The crystallization and melting behaviors of the components were analyzed by differential scanning calorimetry, which is thought to be favorable for an understanding of the distribution of FMWCNTs. It is interesting to observe that the morphology of PA6 particles is very dependent on the method of preparation of the nanocomposites. Correspondingly, FMWCNTs exhibit an apparent reinforcement effect and/or an excellent toughening effect for the compatibilized HDPE/PA6 blend, depending upon their distribution state and the variation of PA6 morphology. This work proves that FMWCNTs have a potential application in further improving the mechanical properties of compatibilized immiscible polymer blends. Copyright © 2012 Society of Chemical Industry     

Influence of carbon nanotubes with different functional groups on the morphology and properties of PPO/PA6 blends

Carbon nanotubes with different functional groups were prepared and then incorporated into the poly(2,6‐dimethyl‐1,4‐phenylene oxide)/polyamide 6 (PPO/PA6) blend via melt blending. The influence of different carbon nanotubes on the morphology and properties of the blend was studied. The results show that addition of pristine CNTs, CNTs‐OH, CNTs‐NH₂ leads to the evolution of the phase structure of PPO/PA6 (mass ratio: 60/40) blend from sea‐island to cocontinuous, whereas incorporation of CNTs‐COOH does not change the blend morphology due to serious aggregation of the carbon nanotubes. Incorporating different CNTs into PPO/PA6 blend increases the tensile modulus and storage modulus of the blends, whereas decreases slightly the tensile strength. At the same time, the glass transition temperatures (T_g) of PA6 and PPO are enhanced. ΔT_g, the gap between the T_g of PA6 and PPO, decreases with the addition of carbon nanotubes due to the stronger interaction of carbon nanotubes with PA6 than PPO. A similar tendency was found in the storage modulus (G′) and complex viscosity (η*) of the composites. The dispersion state of different carbon nanotubes and their interaction with polymer components are different, which causes the different confinement effect to the macromolecular chains. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

TPU/PLA nanocomposites with improved mechanical and shape memory properties fabricated via phase morphology control and incorporation of multi-walled carbon nanotubes nanofillers

Shape memory polymer nanocomposites based on thermoplastic polyurethane (TPU)/polylactic acid (PLA) blends filled with pristine multi-walled carbon nanotubes (MWCNTs) and modified MWCNTs─COOH were fabricated by direct melt blending technique and investigated for its morphology, mechanical, thermal, electrical, and shape memory properties. Morphological characterizations by using transmission electron microscope (TEM) and field emission scanning electron microscope (FESEM) revealed better dispersion of MWCNTs─COOH in the polymer blend, which is attributed to the improved interfacial interactions between the polymer blends and MWCNTs-COOH. Loading of the MWCNTs-COOH in the TPU/PLA blends resulted in the significant improvements in the mechanical properties such as tensile strength and elastic modulus and these effects are more pronounced on increasing the MWCNTs─COOH loading amount, when compared to the pristine MWCNTs filled system. Thermal analysis showed that the glass transition temperature of the blends increases slightly with increasing loading of both pristine and modified MWCNTs in the system. The resistance of nanocomposites decreased from 2 × 10¹² Ω to 3.2 × 10¹⁰ Ω after adding 3% MWCNTs─COOH. The shape memory performance tests showed that the enhancement of shape recovery by 252% could be achieved at 3% MWCNTs loading, when compared to that of TPU/PLA blends.