Defluoridation of drinking water by Mg/Al hydrotalcite-like compounds and their calcined products

Fluorosis, developed in the population who depends on water with high concentrations of fluoride for their daily drinking usage, is one of the most frequently occurring endemic diseases. To search for effective defluoridation agents, we studied F⁻ adsorption by synthetic Mg/Al–CO₃ hydrotalcite-like compounds (HT) and their calcined products (HTC). The adsorption experiments were carried out as a function of time, pH, and the adsorbate concentration. The affecting factors to fluoride sorption were found to be solution pH and the crystallinity of the HT. The results from our adsorption experiments indicated that F⁻ uptake by HTC was much stronger than their precursors HT. It was further observed that the maximal adsorption takes place within the first 15 min. HTs and HTCs exhibit a reversed trend in F⁻ uptake with regard to temperature of the hydrothermal treatment to HT. At any specific initial F⁻ concentration, the removal efficiency of F⁻ increases with the temperature for HTC, but decreases for HT. The removal efficiency is inversely related to the initial fluoride concentration for HTC obtained from HT synthesized at 130 °C (HTC130, the most efficient adsorbent seen in this study). The adsorption isotherm at pH 7 for HTC130 was linear and did not follow Langmuir equation; the K value (slope of the line) was calculated to be 0.46 L/g. HTC130 was shown to be able to bring F⁻ concentration from 5 mg/L down to less than 1 mg/L in aqueous solution, suggesting that this material may be a possible candidate for F⁻ removal.     

测试——聚乙烯亚胺改性磁性膨润土对Pb2+和Cu2+的吸附性能(测试稿件)

在磁性膨润土(MBent)表面接枝聚乙烯亚胺(PEI)制备了聚乙烯亚胺改性磁性膨润土(PEI/KH560/MBent),采用FTIR、VSM、XRD、TGA、EA、SEM和EDS对其进行了表征,考察了其对水溶液中Pb_²⁺和Cu_²⁺的吸附性能。结果表明,聚乙烯亚胺已成功接枝于磁性膨润土表面,并有效提高其对Pb_²⁺和Cu_²⁺吸附量；溶液初始pH对吸附量影响较大,随着pH的增大,吸附量增加。在pH=5,溶液初始质量浓度为300 mg/L,PEI/KH560/MBent对Pb_²⁺和Cu_²⁺吸附量分别为96.21和61.08 mg/g；吸附过程符合准二级动力学模型,吸附行为符合Langmuir吸附等温模型。热力学研究表明,吸附为自发吸热过程。经过5次循环利用后,其吸附容量仍保持初始的60%以上,表明PEI/KH560/MBent具有一定的重复利用性。     

Application of graphene-based adsorbents in the treatment of dye-contaminated wastewater; kinetic and isotherm studies

The adsorption of methylene blue (MB) on graphene-based adsorbents was tested through the batch experimental method. Two types of graphene-based adsorbents as graphene oxide (GO) and reduced graphene oxide (RGO) were compared to investigate the best adsorbent for MB removal. So that optimizing the MB removal for the selected type of graphene-based adsorbent, the diverse experimental factors, as pH (2–10), contact time (0–1440 min), adsorbent dosage (0.5–2 g/L), and initial MB concentration (25–400 mg/L) were analyzed. The conclusions indicated that the MB removal rised with an increase in the initial concentration of the MB and so rises in the amount of adsorbent used and initial pH. Maximum dye removal was calculated as 99.11% at optimal conditions after 240 min. Adsorption data were compiled by the Langmuir isotherm (R²: 0.999) and pseudo-second-order kinetic models (R²: 0.999). The Langmuir isotherm model accepted that the homogeneous surface of the GO adsorbent covering with a single layer. And the adsorption energy was calculated as 9.38 kJ mol⁻¹ according to the D-R model indicating the chemical adsorption occurred. The results show that GO could be utilized for the treatment of dye-contaminated aqueous solutions effectively.     

Removal and recovery of phosphate ions from aqueous solutions by amine functionalized epichlorohydrin-grafted cellulose

A novel cellulose grafted epichlorohydrin functionalized polyethylenimine (Cell-g-E/PEI) graft copolymer was synthesized using cellulose, epichlorohydrin and polyethylenimine in the presence of azetobis isobutyro nitrile (AIBN) as the initiator and N,N′-Methylene bisacrylamide (MBA) as the crosslinking agent. The graft copolymer, Cell-g-E/PEI was characterized using TGA/DTG, XRD, FTIR, and SEM-EDS to evaluate the structural and morphological characteristics of the graft copolymer. The effectiveness of the Cell-g-E/PEI, as adsorbent for the removal and recovery of phosphate ions from aqueous media was studied. The effects of pH, contact time, and initial sorbate concentration were studied to optimize the conditions for maximum adsorption. The adsorption process, which was pH dependent, shows maximum removal (> 99.0%) at pH 4.5. Kinetic study showed that 180 min of contact at 100 mg/L could adsorb about 99.6% of phosphate onto Cell-g-E/PEI. A pseudo-second-order kinetic model described successfully the kinetics of sorption of phosphate. Adsorption equilibrium data were correlated with the Langmuir, Freundlich and Redlich–Peterson isotherm models. The best fit was obtained with Freundlich model. Desorption of phosphate was studied by using 0.1 M HCl. Adsorption/desorption for more than six cycles showed the possibility of repeated use of this graft copolymer for the removal and recovery of phosphate from aqueous solutions.     

Adsorption of platinum(IV) from an aqueous solution with magnetic cellulose functionalized with thiol and amine as a nano‐active adsorbent

In this study, magnetic cellulose was prepared and then functionalized by the grafting of glycidyl methacrylate and reaction with thiourea/amine [to produce grafted magnetic cellulose with thiol/amine (GMC–N/S)]. Thus, GMC–N/S as a nano‐active adsorbent was investigated for the adsorption of Pt(IV) in a batch system. A response surface methodology was used to study the effects of four independent variables [Pt(IV) concentration, temperature, pH of the solution, and adsorbent dose] and to optimize the process conditions for the maximum adsorption of platinum(IV) from aqueous solutions by GMC–N/S. A high coefficient of determination (R² = 98.46) implied the adsorption of Pt(IV) onto the adsorbent in a valid manner, and only 1.54% of the total variable was not explained by the model. The equilibrium adsorption data were fitted to the Langmuir isotherm. The maximum monolayer adsorption capacity of the adsorbent (GMC–N/S) for Pt(IV) was determined to be 40.48 mg/g. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45361.     

Preparation of magnetic zeolite/chitosan composite using silane as modifier for adsorption of Cr(VI) from aqueous solutions

This study aimed to prepare an efficient, cost-effective, and separable magnetic zeolite/chitosan composite (MZFA/CS) adsorbent from solid waste to deal with the water pollution of Cr(VI). The MZFA/CS was characterized by X-ray fluorescence (XRF), Fourier transform infrared (FTIR) spectroscopy, X-ray diffraction (XRD), and vibrating sample magnetometer (VSM) techniques. Then, the effect of pH, temperature, initial concentration of Cr(VI) ions, and contact time was considered in the study. For a sorbent dose of 0.1 g in 50 mL of a Cr(VI) solution, at a contact time of 30 min, temperature of 30°C, and a pH of 3, an adsorption capacity (q_e) of 16.96 mg g⁻¹ was achieved. Adsorption kinetics and isotherm data obtained for all adsorption systems were well-fitted by pseudo-second-order and Langmuir models, respectively. The thermodynamic study suggested that the adsorption process is spontaneous and endothermic in nature. In summary, the adsorbent with better separability (Ms = 16.83 emu g⁻¹) and adsorbability was successfully fabricated.     

Removal of arsenic(III) from aqueous solution by concrete-based adsorbents

The present paper investigates the adsorption of arsenic(III) (As(III)) onto 2 concrete-based low-cost materials, i.e., Aerocrete and Vermiculite impregnated by ferric oxyhydroxide. Adsorption experiments were performed to study the effect of initial pH, initial concentration of As(III), contact time, and ions usually present in water. No significant effect of the initial pH on the adsorption of As(III) by Aerocrete and Vermiculite was observed at the pH range of 4–8. The As(III) removal efficiency decreased at a high initial pH (i.e., 10). The Langmuir isotherm showed that the maximum As(III) adsorption capacity of Aerocrete and Vermiculite is 15.15 and 13.51 mg/g, respectively, which is higher than that observed using titanium dioxide (i.e., 3.52 mg/g), at pH 7 and 24 ±1 °C. A pseudo-second order kinetic model fitted well the experimentally obtained kinetic data. This suggests that chemisorption most probably controls the adsorption of As(III) on Aeroctere and Vermiculite. Significantly, As(III) (1 mg/L) could be removed almost completely by both Aeroctere and Vermiculite (1 g/L) in 30 and 60 min, respectively at pH 7 and 24 ±1 °C. Importantly, Ca²⁺, Mg²⁺, Na⁺, HCO₃⁻, SO₄²⁻, and Cl⁻ ions had no significant effect on the adsorption of As(III) on Aeroctere and Vermiculite. The results showed that the proposed concrete-based adsorbents have the potential to remove As(III) from water.     

Polyethylenimine‐grafted and HSA‐immobilized poly(GMA–MMA) affinity adsorbents for bilirubin removal

The epoxy‐group‐containing microspheres from cross‐linked glycidyl methacrylate and methyl methacrylate, poly(GMA–MMA), were prepared by suspension polymerisation. The epoxy groups of the poly(GMA–MMA) microspheres were used for grafting with an anionic polymer polyethylenimine (PEI) to prepare non‐specific affinity adsorbents (poly(GMA–MMA)–PEI) for bilirubin removal. The specificity of the poly(GMA–MMA)–PEI adsorbent to bilirubin was further increased by immobilization of human serum albumin (HSA) via adsorption onto PEI‐grafted poly(GMA–MMA) adsorbent. Various amounts of HSA were immobilized on the poly(GMA–MMA)–PEI adsorbent by changing the medium pH and initial HSA concentration. The maximum HSA content was obtained at 68.3 mg g^?1 microspheres. The effects of pH, ionic strength, temperature and initial bilirubin concentration on the adsorption capacity of both adsorbents were investigated in a batch system. Separation of bilirubin from human serum was also investigated in a continuous‐flow system. The bilirubin adsorption on the poly(GMA–MMA)–PEI and poly(GMA–MMA)–PEI–HSA was not well described by the Langmuir model, but obeyed the Freundlich isotherm model. The poly(GMA–MMA)–PEI affinity microspheres are stable when subjected to sanitization with sodium hydroxide after repeated adsorption–desorption cycles. Copyright © 2004 Society of Chemical Industry     

Enhanced adsorptive removal of Cr(VI) in aqueous solution by polyethyleneimine modified palygorskite

Polyethyleneimine (PEI) modified palygorskite (Pal) was used for the adsorption of Cr(VI) in aqueous solution. The absorbent was characterized by Fourier transform infrared spectroscopy (FT-IR) and thermogravimetric analysis (TGA). Characterized results confirmed that the Pal has been successfully modified by PEI. The modification of PEI increased the Cr(VI) adsorption performance of the Pal by the adsorption combined reduction mechanism, and amino groups of the adsorbent play the main role in the enhanced Cr(VI) adsorption. The maximum adsorption capacity was 51.10 mg·g⁻¹ at pH 4.0 and 25 °C. The adsorption kinetics of Cr(VI) on the adsorbent conforms to the Langmuir isotherm model. The maximum adsorption occurs at pH 3, and then the adsorption capacity of PEI-Pal was decreased with the increase of pH values. The adsorption kinetics of Cr(VI) on PEI-Pal was modeled with pseudo-second-order model. The addition of Cl⁻, SO₄²⁻ and PO₄³⁻ reduced the Cr(VI) adsorption by competition with Cr(VI) for the active sites of PEI-Pal. The Cr(VI) saturated PEI-Pal can be regenerated in alkaline solution, and the adsorption capacity can still be maintained at 30.44 mg·g⁻¹ after 4 cycles. The results demonstrate that PEI-Pal can be used as a potential adsorbent of Cr(VI) in aqueous solutions.     

Removal of acid dyes from aqueous solutions using a new eco-friendly nanocomposite of CoFe2O4 modified with Tragacanth gum

A new composite of cobalt ferrite and Tragacanth gum (TG) was developed and applied to remove methyl orange (MO) and methyl red (MR) from wastewater samples simultaneously. The results showed that the presence of TG improved the capability of cobalt ferrite in removing the pollutants in considerably. The adsorption properties and surface morphology of the sorbent were compared with those of bare cobalt ferrite, TG, and TG grafted copolymer. The properties of the adsorbents were studied using Fourier transform infrared, scanning electron microscope, transmission electron microscope, X-ray diffraction, and vibrating sample magnetometer, and the effects of different factors such as the amount of the adsorbent, sample pH, contact time, and initial concentration were also evaluated and optimized through response surface methodology using central composite design. The optimal conditions for the adsorption of both dyes (100 mg L⁻¹ as the concentration) were pH of 4.0, adsorbent dose of 0.5 mg mL⁻¹, and contact time of 110 min. Under these conditions, the MO and MR adsorption processes were found to follow pseudo-second-order kinetic model. The equilibrium adsorption data followed the Langmuir isotherm and the highest adsorption capacity was determined to be 336 and 387 mg g⁻¹ for MO and MR, respectively. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 137, 48605.     

Synthesis of chemically modified chitosan with 2,5‐dimercapto‐1,3,4‐thiodiazole and its adsorption abilities for Au(III), Pd(II), and Pt(IV)

A new chemically modified chitosan hydrogel with 2,5‐dimercapto‐1,3,4‐thiodiazole (CTS‐DMTD) has been synthesized. The structure of CTS‐DMTD was confirmed by elemental analysis and FTIR. It was found that adsorption capacities were significantly affected by the pH of solution, with optimum pH values of 3.0 for Au(III), 2.0 for Pd(II) and Pt(IV). The saturated adsorption capacities were 198.5 mg/g for Au(III), 16.2 and 13.8 mg/g for Pd(II) and Pt(IV), respectively. Langmuir and Freundlich isotherm adsorption models were applied to analyze the experimental data. The results showed that adsorption isotherms of Pd(II) and Pt(IV) could be well described by the Langmuir equation. The adsorption kinetic investigations indicated that the kinetic data correlated well with the pseudo‐second‐order model. The recovery experimental data showed that CTS‐DMTD had a higher affinity toward Au(III), Pd(II), and Pt(IV) in the coexistence system containing Cu(II), Fe(III), Cd(II), Ni(II), Mg(II), and Zn(II). The studies of desorption were carried out using various reagents and the optimum effect was obtained using thiourea. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Removal of Reactive Blue 21 onto magnetic chitosan microparticles functionalized with polyamidoamine dendrimers

Chitosan/poly(amidoamine) (MCS/PAMAM) microparticles were prepared as magnetic adsorbents for removal of Reactive Blue 21 (RB 21) dye from aqueous solution. Characterization of these particles was carried out using scanning electron microscopy, Fourier transform-infrared spectroscopy, X-ray diffractometry and vibrating sample magnetometry. The results indicate that the magnetic chitosan microparticles (MCS) were functionalized with PAMAM dendrimers and maintained its intrinsic magnetic properties. The effects of initial pH, adsorbent dose, initial concentration, contact time and temperature on adsorption were investigated. Kinetic studies showed that the dye adsorption process followed a pseudo-second-order kinetic model but that the adsorption rate was also influenced by intraparticle diffusion. Equilibrium adsorption isotherm data indicated a good fit to the Langmuir isotherm. The maximum adsorption capacities obtained from the Langmuir model were 555.56, 588.24, 625.00 and 666.67 mg g⁻¹ at 303, 313, 323 and 333 K, respectively. The thermodynamic parameters revealed the feasibility, spontaneity and endothermic nature of the adsorption. Recycling experiments confirmed the relative reusability of the adsorbent.     

Selective separation and concentration of Pd(II) from Fe(III), Co(II), Ni(II), and Cu(II) ions using thiourea‐formaldehyde resin

Thiourea‐formaldehyde (TUF), a well‐known chelating resin, has been synthesized and it was used in the adsorption, selective separation, and concentration of Pd(II) ions from Fe(III), Co(II) Ni(II), and Cu(II) base metal ions. The composition of the synthesized resin was determined by elemental analysis. The effect of initial acidity/pH and the adsorption capacity for Pd(II) ions were studied by batch technique. The adsorption and separation of Pd(II) were then examined by column technique. FTIR spectra and SEM/EDS analysis were also recorded before and after the adsorption of Pd(II). The optimum pH was found to be 4 for the adsorption. The adsorption data fitted well to the Langmuir isotherm. The maximum adsorption capacity of the TUF resin for Pd(II) ions was found to be 31.85 mg g⁻¹ (0.300 mmol g⁻¹). Chelating mechanism was effective in the adsorption. Pd(II) ions could be separated efficiently from Fe(III), Cu(II), Ni(II), and Co(II) ions using TUF resin. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

3D flower like δ-MnO2/MXene Nano-hybrids for the removal of hexavalent Cr from wastewater

Herein, 3D flower-like δ-MnO₂, MXene and δ-MnO₂/MXene in-situ hybrid (IH) composites were prepared (via hydrothermal and solution treatment methods) for the effective removal of Cr (VI) from the contaminated water. The effect of various experimental parameters including contact time, pH levels and initial Cr (VI) ions concentration was determined and compared under static conditions. The kinetics of Cr (VI) adsorption onto δ-MnO₂, MXene, and IH confirmed the existence of a pseudo-second-order model. The obtained results reveal that the removal of Cr (VI) largely depends on the pH of the solution. The adsorption isotherm data fits best for Freundlich model, illustrating a multi-site adsorption mechanism of Cr (VI) ion on these adsorbents. The maximum Cr (VI) adsorption capacities onto δ-MnO₂, MXene and IH are 235.65 mg g⁻¹, 273.1 mg g⁻¹ and 353.87 mg g⁻¹, respectively. The study reveals that hetero-engineered approach of synthesizing transition metal oxides with MXenes provides abundant opportunities to remove contaminants from water with better efficiency due to reduction and electrostatic interaction.     

Preparation and application of glycidyl methacrylate and methacrylic acid monomer mixture‐grafted poly(ethylene terephthalate) fibers for removal of methylene blue from aqueous solution

A novel fibrous adsorbent that grafts glycidyl methacrylate (GMA) and methacrylic acid (MAA) monomer mixture onto poly(ethylene terephthalate) (PET) fibers was used for removal of methylene blue (MB) in aqueous solutions by a batch equilibration technique. The operation parameters investigated included, pH of solution, removal time, graft yield, dye concentration, and reaction temperature. The adsorption rate of MB is much higher on the MAA/GMA‐grafted PET fibers than on the ungrafted PET fibers. MB was removed 99% the initial dye concentration at 10 mg L⁻¹ and 93% at 200 mg L⁻¹ by monomers mixture‐grafted PET fibers. Pseudofirst order and pseudosecond order kinetic equations were used to examine the experimental data of different graft yield. It was found that the pseudosecond order kinetic equation described the data of dye adsorption on fibrous adsorbent very well. The experimental isotherms data were analyzed using Langmuir and Freundlich isotherm models. The data was that Freundlich isotherm model fits the data very well for the dyes on the fibers adsorbent. The dye adsorbed was easily desorbed by treating with acetic acid/methanol mixture (50% V/V) at room temperature. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Powerful adsorption of silver(I) onto thiol-functionalized polysilsesquioxane microspheres

The strong adsorbability of Ag(I) ions onto poly(3-mercaptopropylsilsesquioxane) (PMPSQ) microspheres synthesized through a two-step acid–base catalyzed sol–gel process method was systematically examined. The effect of adsorption time, initial Ag(I) concentration, and solution pH was studied to optimize the Ag(I) adsorbability of PMPSQ microspheres. The PMPSQ microspheres demonstrate a powerful Ag(I) adsorbability with an adsorptivity above 99.99% when the initial Ag(I) concentration is lower than 10 mM and the highest Ag(I) adsorbance of 1140 mg/g at an initial Ag(I) concentration of 150 mM. Adsorption phenomena appeared to follow Langmuir isotherm. The kinetic studies indicated that the adsorption process well fits the pseudo-second-order kinetics with a very rapid initial adsorption rate of 15.28 mg g^?1 min^?1. The appropriate solution pH for Ag(I) adsorption is around 2.0–5.4. The PMPSQ microspheres demonstrate a promising application in the removal of Ag(I) ions from aqueous solutions.     

Kinetics and equilibrium of cobalt ion adsorption on cross‐linked polyethylenimine membrane

The kinetics and equilibrium of cobalt ion adsorption on crosslinked polyethylenimine (PEI) membrane were studied by the spectroscopic method in terms of time, cobalt ion concentration, and temperature. It was found that the adsorption of cobalt ion on crosslinked PEI membrane obeyed the pseudofirst‐order kinetic model and the equilibrium adsorption amount of cobalt ion on crosslinked PEI membrane was closely related to the initial cobalt ion concentration. The equilibrium adsorption amount increased with the decrease of temperature and obeyed a Langmuir isotherm to give the equilibrium constant for the adsorption of cobalt ion on crosslinked PEI membrane under various temperatures. Based on Van't Hoff equation the enthalpy and entropy of the adsorption of cobalt ion on crosslinked PEI membrane were determined to be ?12.9 kJ mol^?1 and ?107 J mol^?1 K^?1, respectively. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Removal behavior and mechanism of silver from low concentration wastewater using cellulose aerogel modified by thiosemicarbazide

Due to the low concentration of silver in water, most of the cellulose adsorbents exhibited low removal efficiency, which greatly limited their practical applications. Herein, a cellulose aerogel modified by thiosemicarbamide (CAT) was fabricated for reducing and adsorbing silver ions from low concentration wastewater. The characterization results concluded that CAT owned a three-dimensional spongy structure with many circular microspheres and a better specific surface area (19.37 m² g⁻¹), as well as the functional groups of ─C═N⁺─H and ─(C═S)─N. The static batch adsorption experiments demonstrated that CAT could reached the maximum removal percentage of 94.94% and adsorption capacity of 42.12 mg g⁻¹ under the initial concentration of Ag(I) was 15 mg L⁻¹ and the pH value was 7. Meanwhile, the adsorption of Ag(I) on CAT was second-order reaction, and the Langmuir model could better fit the adsorption process. In addition, CAT exhibited wide pH values (1–9) adaptability and excellent adsorption performance for silver through electrostatic interaction, chelation, and reduction. This study probably provides a new method as well as important experimental data and theoretical reference for the removal of silver ions and other metals.     

Synthesis of α‐cellulose/polypyrrole composite for the removal of reactive red dye from aqueous solution: Kinetics and equilibrium modeling

In this work, a composite from α‐cellulose coated with conducting polypyrrole by in situ polymerization using potassium persulfate as oxidant was obtained. The composite was characterized by fourier transform infrared (FTIR) spectroscopy, cyclic voltammetry, UV/Vis spectroscopy, and scanning electron microscopy (SEM) analysis showed homogeneous coating of α‐cellulose with polypyrrole (PPy) to produce a composite with a conductivity of 3.5 × 10⁻⁵ S/m. Batch aqueous adsorption experiments of the reactive red 120 (RR120) dye onto the synthesized material were conducted. The results showed that this composite is an efficient adsorbent for RR120 dye removal. For the adsorption experiments set to an initial pH of 3.9, the adsorption capacity was 15.6 mg of dye/g of composite for an equilibrium concentration (in the liquid) of RR120 dye equal to 1,000 mg/L, whereas a value of 96.1 mg of dye/g of composite was obtained when the solution pH was set to 2.0 for the same equilibrium concentration. When performing adsorption experiments using pure α‐cellulose, dye adsorption was insignificant at any pH value. Adsorption isotherm for RR120 was described by a typical Freundlich model. The transient adsorption of RR120 on the synthesized composite was described by a general three‐resistance model that includes the transport on the film that surrounds the composite particles, diffusion inside the particles, and adsorption on the surface of the particles. A fitting of the uptake curves was performed allowing the estimation of values for the effective diffusivity, D₀, and the adsorption rate coefficient, k₁. For the adsorption experiments with an initial pH value set to 3.9, D₀ was estimated as 1.05 × 10⁻¹⁰ m²/s, whereas k₁ was 1.65 × 10⁻⁴ Lⁿ/g mg^{n − 1} s; the corresponding values of k₁ at pH = 2 and 9.0 were 3.18 × 10⁻⁴ and 5.16 × 10⁻⁵, respectively. POLYM. COMPOS., 36:312–321, 2015. © 2014 Society of Plastics Engineers     

Larger pore volume tetraphenyladamantane-based hybrid porous polymers: Facile Friedel–Crafts preparation,CO2 capture,and Rhodamine B removal properties

Synthesis of covalently linked porous polymers with high surface area and larger pore volume for two or more task-specific functionalities is always a big challenge. In this article, the facile Friedel–Crafts reaction is employed to construct the hierarchical hybrid porous polymers (HPPs) from tetraphenyladamantane and octavinylsilsesquioxane. The resulting polymers, HPP-1 to HPP-3, possessed the surface areas from 1356 to 1511 m² g⁻¹, and the pore volumes from 2.05 to 2.67 cm³ g⁻¹. All these polymers feature micropores, mesopores, and macropores in nature. The resultant polymers exhibit high CO₂ adsorption capacity up to 2.0 mmol g⁻¹ (8.82 wt %), at 273 K, 1.0 bar, and the maximum Rhodamine B (RB) sorption capacity of 653.6 mg g⁻¹. To illustrate the adsorption process, the effects of factors, contact time, initial concentration, temperature, and pH value on the adsorption capacity of RB were studied. The adsorption equilibrium data displayed a better fitting to the Langmuir isotherm model than the Freundlich model and the adsorption kinetics fitted well with the pseudo-second-order kinetic model. The recycle experiments displayed that the capacity recovery was still higher than 95% after four cycles. Theses polymers are promising to be the adsorbents for capturing CO₂ and removing RB. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 136, 48572.