带有ESD保护,900MHz/2.4 GHz Dual-BandCMOS LNA的设计

设计了一个可以同时工作在900 MHz和2.4 GHz的双频带(Dual-Band)低噪声放大器(LNA).相对于使用并行(parallel)结构LNA的双频带解决方案,同时工作(concurrent)结构的双频带LNA更能节省面积和减少功耗.此LNA在900MHz和2.4 GHz两频带同时提供窄带增益和良好匹配.该双频带LNA使用TSMC 0.25 μm 1P5M RF CMOS工艺.工作在900MHz时,电压增益、噪声系数(Noise Figure)分别是21 dB、2.9 dB;工作在2.4 GHz时,电压增益、噪声系数分别是25dB、2.8 dB,在电源电压为2.5 V时,该LNA的功耗为12.5mW,面积为1.1mm×0.9 mm.使用新颖的静电防护(ESD)结构使得在外围PAD上的保护二极管面积仅为8 μm×8 μm时,静电防护能力可达2 kV(人体模型)     

Design of 3.1–10.6 GHz ultra-wideband CMOS low noise amplifier with current reuse technique

A new low complexity ultra-wideband 3.1–10.6 GHz low noise amplifier (LNA), designed in a chartered 0.18 μm RFCMOS technology, is presented in this paper. The ultra-wideband LNA only consists of two simple amplifiers with an inter-stage inductor connected. The first stage utilizing a resistive current reuse and dual inductive degeneration techniques is used to attain a wideband input matching and low noise figure. A common source amplifier with inductive peaking technique as the second stage achieves high flat gain and wide the −3 dB bandwidth of the overall amplifier simultaneously. The implemented ultra-wideband LNA presents a maximum power gain of 15.6 dB, a high reverse isolation of −45 dB and a good input/output return losses are better than −10 dB in the frequency range of 3.1–10.6 GHz. An excellent noise figure (NF) of 2.8–4.7 dB was obtained in the required band with a power dissipation of 14.1 mW under a supply voltage of 1.5 V. An input-referred third-order intercept point (IIP3) is −7.1 dBm at 6 GHz. The chip area including testing pads is only 0.8 mm × 0.9 mm.     

0.6V CMOS低噪声放大器的设计与优化*

采用SMIC 0.18 μm CMOS工艺设计了一个低电压低功耗的低噪声放大器(Locked Nucleic Acid,LNA).分析了在低电压条件下LNA的线性度提高及噪声优化技术.使用Cadence SpectreRF仿真表明,在2.4 GHz的工作频率下,功率增益为19.65 dB,输入回波损耗S11为-12.18 dB,噪声系数NF为1.2 dB,1 dB压缩点为-17.99 dBm,在0.6V的供电电压下,电路的静态功耗为2.7 mW,表明所设计的LNA在低电压低功耗的条件下具有良好的综合性能.     

一种基于中和电容的60 GHz CMOS差分LNA

针对毫米波频段下硅基CMOS晶体管的栅漏寄生电容严重影响放大器的增益和隔离度的问题,采用交叉耦合中和电容抵消其影响,设计了一款60 GHz三级差分共源极低噪声放大器(LNA)。为减小级间匹配无源器件的损耗,节省芯片面积,采用变压器进行级间耦合。基于SMIC 55 nm RF CMOS工艺,进行了电路原理图和版图的设计与仿真。仿真结果显示,该LNA输入输出匹配良好,功率增益为21.1 dB,3 dB带宽为57.3~61.5 GHz,噪声系数为5.5 dB,输出1 dB压缩点为－0.64 dBm,功耗为34.4 mW,芯片尺寸为390 μm×670 μm。     

1V高线性度2.4GHz CMOS低噪声放大器

讨论了低噪声放大器(LNA)在低电压、低功耗条件下的噪声优化及线性度提高技术.使用Chartered 0.25μm RF CMOS 工艺设计一个低电压折叠式共源共栅LNA.后仿真结果表明在1V电源下,2.36GHz处的噪声系数NF仅有1.32dB,正向增益S21为14.27dB,反射参数S11、S12、S22分别为 -20.65dB、-30.27dB、-24dB,1dB压缩点为-13.0dBm,三阶交调点IIP3为-0.06dBm,消耗的电流为8.19mA.     

应用于2.4GHz无线传感网的带ESD保护CMOS低噪声放大器的设计与优化

本文给出一种新的带ESD保护源极电感负反馈低噪声放大器优化方法,可以实现在功耗受限条件下的噪声和输入同时匹配,并给出了输入阻抗和噪声参数的分析。采用该方法设计并优化了一个基于0.18-μm RF CMOS工艺、应用于无线传感网的2.4GHz低噪声放大器。测试结果表明,低噪声放大器的噪声系数为1.69dB,功率增益为15.2dB,输入1dB压缩点为-8dBm,输入三阶截点为1dBm,1.8V电源电压下的工作电流为4mA。     

Design and optimization of CMOS LNA with ESD protection for 2.4 GHz WSN application

A new optimization method of a source inductive degenerated low noise amplifier(LNA) with electrostatic discharge protection is proposed.It can achieve power-constrained simultaneous noise and input matching. An analysis of the input impedance and the noise parameters is also given.Based on the developed method,a 2.4 GHz LNA for wireless sensor network application is designed and optimized using 0.18-μm RF CMOS technology. The measured results show that the LNA achieves a noise figure of 1.59 dB,a power gain of 14.12 dB, an input 1 dB compression point of-8 dBm and an input third-order intercept point of 1 dBm.The DC current is 4 mA under a supply of 1.8 V.     

应用于DSRC系统的5.8GHz CMOS LNA设计

基于TSMC 0.18μm CMOS RF工艺,完成了一个全集成共源-共栅低噪声放大器设计。版图后仿真结果表明:1.8V电源电压下,电路静态功耗约为17mW;在DSRC系统工作频段上,电路实现了良好的综合性能指标,输入反射系数(S11)和输出反射系数(S22)小于-15dB,增益(S21)大于14.0dB,反向隔离度(S12)达到32dB,噪声系数小于2dB,并且工作稳定。     

Design of low power UWB LNA based on common source topology with current-reused technique

This paper presents two low power UWB LNAs with common source topology. The power reduction is achieved by the current-reused technique. The gain and noise enhancement of the proposed circuit is based on an output buffer which is used by a common source amplifier with shunt–shunt feedback. Chip1 is an adopted T-match input network of 50 Ω matching in the required band. Measurements show that the S₁₁ and S₂₂ are less than −10 dB, and the maximum amplifier gain S₂₁ gives 9.7 dB, and the noise figure is 4.2 dB, the IIP3 is −8.5 dBm, and the power consumption is 11 mW from 1.1 V supply voltage. The input matching of chip2 is adopted from a LC high pass filter and source degenerated inductor. The output buffer with the RC-feedback topology can improve the gain, increase the IIP3, restrain the noise, improve the noise figure and decrease the DC power dissipation. Measurements show 13.2 dB of power gain, 3.33 dB of noise figure, and the IIP3 is −3.3 dBm. It consumes 9.3 mW from 1.5 V supply voltage. These two chips are implemented in a 0.18 μm TSMC CMOS process.     

一种应用于6-9GHz UWB系统的低噪声CMOS射频前端设计

本文介绍了一种应用于6-9 GHz超宽带系统的全集成差分CMOS射频前端电路设计。在该前端电路中应用了一种电阻负反馈形式的低噪声放大器和IQ两路合并结构的增益可变的折叠式正交混频器。芯片通过TSMC 0.13µm RF CMOS工艺流片,含ESD保护电路。经测试得该前端电路大电压增益为23~26dB,小电压增益为16~19dB;大增益下前端电路平均噪声系数为3.3-4.6dB,小增益下的带内输入三阶交调量(IIP3)为-12.6dBm。在1.2V电压下,消耗的总电流约为17mA。     

A low-noise mixer with an image-reject notch filter for 2.4 GHz applications

This paper presents a low noise first down-conversion mixer with a notch filter for the heterodyne receiver. The notch filter connected to the output node of the mixer driver stage plays a role of image rejection at an image frequency, thereby suppressing the sideband image noise and improving the mixer noise performance. Targeted for 2.4 GHz industrial-scientific-medical band applications, a simple source-degenerated down-conversion single balanced mixer with the filter is implemented. The measurement results of the proposed down-conversion mixer shows about 3.0 dB improvement of single-side band noise figure, about 2.9 dB power conversion gain improvement, and 25 dB image suppression compared to those without the filter dissipating 4 mA from a 2.5 V supply voltage.     

Sub-mA single ended CMOS low noise amplifier with 2.41 dB noise figure

This paper presents a single ended low noise amplifier (LNA) using 0.18 μm CMOS process packed and tested on a printed circuit board. The LNA is powered at 1.0 V supply and drains 0.95 mA only. The LNA provides a forward gain of 11.91 dB with a noise figure of only 2.41 dB operating in the 0.9 GHz band. The measured value of IIP3 is 0.7 dBm and of P1dB is −12 dBm. Zhang Liang is currently with Cyrips, Singapore. Ram Singh Rana was born in Delhi (India). Having primary education in Bijepur, Dwarahat(India), he received the B.Tech. (hons.) degree in Computer Engineering from G.B. Pant University, Pantnagar, India in 1988 and the Ph.D degree from the Indian Institute of Techonology (IIT), Delhi, India in 1996. He worked for his Ph.D in the Centre for Applied Research in Electronics, IIT Delhi in close interaction with the Semiconductor Complex Limited, Mohali, India. He was with ESPL, Mohali(India) in 1988 for a very short period and then served IIT Delhi as Senior Research Associate (88-90) and Senior Scientific Officer (90-95) where his main contributions were on CMOS analog IC design in subthreshold operation. He was a Lecturer in the Kumaon Engg. College, Dwarahat (India) before serving the IIT Roorkee (Formerly Univ. of Roorkee) in 1998 as assistant Professor. In 1999, he was a Manager (Engineering), Semiconductor Product Sector of the Motorola, Noida, India. Since joining the Institute of Microelectronics, Singapore in 2000, he worked mostly on RFICs, Fractional-N PLLs, ADCs. During 2001-2004, he worked there as IC Design Research and Training Program Manager. Currently, he is serving the institute as Senior Research Engineer in CMOS IC design (below 1V) for biomedical and bio-sensors. His current interests include design and consultancy for CMOS ICs/systems for the biomedical and high speed communication applications. Dr. Rana received Young Teacher Career Award from the All India Council for Technical Education in 1997. He was an Adjunct Asstt. Professor with the National University of Singapore (NUS), Singapore in 2004. He is sole inventor of two US granted patents and has filed several other patents. He has authored/co-authored about 40 publications. He has been reviewer for several IEEE journals and conference papers. Dr Rana is a senior member of IEEE and a member of Graduate Program in BioEngineering, NUS Singapore. He has chaired /co-chaired sessions in many international conferences. Zhang Liang was born in China in June 1978. He received the Bachelor degree and the Master degree in Electrical Engineering from the Xi’an JiaoTong University, Xi’an, China, in 2000 and 2003 respectively. Since 2003, he has been a postgraduate student in the Electrical and Computer Engineering department, National University of Singapore(NUS), Singapore and has successfully completed M.Engg degree program of the NUS. He is currently working on RFICs as a design engineer in Cyrips, Singapore. His design and research interests include integrated circuit design for communications. He has authored/co-authored several publications of international standard. Hari K Garg obtained his BTech degree in EE from IITDelhi in 1981. Subsequently, he obtained his MEng & PhD degrees from Concordia University in 1983 & 1985, and MBA from Syracuse University in 1985. He was a faculty member at Syracuse University from 1985 till 1995. He has been with the National University of Singapore since 1995 till present with the exception of 1998-1999 when he was with Philips. Hari’s research interests are in the area of digital signal/image processing, wireless communications, coding theory and digital watermarking. He has published extensively on these and related topics. He is also founder of several companies in the space of mobile telephony. In his spare time, Hari enjoys singing and a good game of Squash.     

A low noise CMOS RF front-end for UWB 6-9 GHz applications

An integrated fully differential ultra-wideband CMOS RF front-end for 6-9 GHz is presented.A resistive feedback low noise amplifier and a gain controllable IQ merged folded quadrature mixer are integrated as the RF front-end. The ESD protected chip is fabricated in a TSMC 0.13μm RF CMOS process and achieves a maximum voltage gain of 23-26 dB and a minimum voltage gain of 16-19 dB,an averaged total noise figure of 3.3-4.6 dB while operating in the high gain mode and an in-band IIP3 of-12.6 dBm while in th...     

Linearization technique using bipolar transistor at 5 GHz low noise amplifier

A CMOS low noise amplifier (LNA) used in wireless communication systems, such as WLAN and CDMA, must have low noise figure, high linearity, and sufficient gain. Several techniques have been proposed to improve the linearity of CMOS LNA circuits. The proposed low noise amplifier achieves high third-order input intercept point (IIP3) using multi-gated configuration technique, by using two transistors, the first is the main CMOS transistor, and the second is bipolar transistor in TSMC 0.18 m technology. Bipolar transistor is used to cancel the third-order component from MOS transistor to fulfill high linearity operation. This work is designed and fabricated in TSMC 0.18 m CMOS process. At 5 GHz, the proposed LNA achieves a measurement results as 16 dBm of IIP3, 10.5 dB of gain, 2.1 dB of noise figure, and 8 mW of power consumption.     

A 1 V switchable CMOS LNA for 802.11A/B WLAN applications

A new dual-band, 2.4 and 5.2 GHz, combined LNA, which can operate at 1 V supply only, for WLAN application is presented. The switched transistor technique is used in the LNA. It could match the input port in two frequency bands and reduce one on-chip spiral inductor usage compared with [1, 2]. Theoretical analysis and transistor level simulation results using 0.18 μm CMOS process from Chartered Semiconductor are presented to demonstrate this idea. Wang-Chi Cheng received his B.Eng., M.Phil., and Ph.D. degrees in Electronic Engineering of the Chinese University of Hong Kong (CUHK) in 1999, 2001 and 2004. His research achievements during M.Phil. and Ph.D. studies were in the field of low voltage receiver front-end circuits design with CMOS technology. He joined the Electrical and Electronic Engineering department of Nanyang Technological University (NTU), Singapore, in May 2005 as a Research Fellow. Now, he is a Senior Engineer in charge of the UWB transceiver IC design in Hong Kong Applied Science and Technology Research Institute (ASTRI). His current research interests include 802.11 A/B WLAN and UWB transceiver design. He is also a paper reviewer of the IEEE Microwave and Wireless Components Letters. Jian-Guo Ma received his B.Sc. and M.Sc. in 1982 and 1988 respectively with honors from Lanzhou university of Chain, and Doctoral Degree in Engineering from Gerhard-Mercator University of Germany in 1996. From Jan. 1982 to March 1991, he has worked with Lanzhou university of China on RF & Microwave Engineering. Before he joined Nanyang Technological University in 1997, he was with Technical University of Nova Scotia, Canada. Now, he is a Professor of the University of Electronic Science and Technology of China. His research interests are: RFIC designs for wireless applications; RF characterization and modeling of semiconductor devices; RF interconnects and packaging; SoC and Applications; EMC/EMI in RFICs. He has published more than 150 technical papers and two books in above mentioned areas. He holds 6 patents in CMOS RFICs. He is now Associate Editor for IEEE Microwave and Wireless Components Letters. Kiat-Seng Yeo received his B.E. (Hons.) (Elect) in 1993, and Ph.D. (Elect. Eng.) in 1996 both from Nanyang Technological University, Singapore. He joined the School of Electrical and Electronic Engineering, Nanyang Technological University, Singapore as a Lecturer in 1996, and became an Assistant Professor and an Associate Professor in 1999 and 2002, respectively. Professor Yeo provides consulting to statutory boards and multinational corporations in the areas of semiconductor devices and electronic circuit design. He has been extensively involved in the modeling and fabrication of small MOS/Bipolar integrated technologies for the last ten years. His research interests also include the design of new circuits and systems (based on scaled technologies) for low-voltage low-power applications; radio frequency integrated circuit (RF IC) design; integrated circuit design of BiCMOS/CMOS multiple-valued logic circuits, domino logic, and memories; and device characterization of deep submicrometer MOSFETs. Manh-Anh Do obtained his B.E. (Hons) (Elect.) in 1973, and Ph.D. (Elect. Eng.) in 1977 both from University of Canterbury, New Zealand. Between 1977 and 1989, he held various positions including: R & D engineer and production manager at Radio Engineering Ltd., research scientist at Fisheries Research Centre, New Zealand, and senior lecturer at National University of Singapore. He joined the School of Electrical and Electronic Engineering, Nanyang Technological University (NTU), Singapore as a senior lecturer in 1989, and obtained the Associate Professorship in 1996 and the Professorship in 2001. He has been a consultant for many projects in the Singapore electronic industry, and was the principal consultant for the design, testing and implementation of the $200 million Electronic Road Pricing (ERP) island-wide project in Singapore, from 1990 to 2001. His current research is on digital and mobile communications, RF IC design, mixed-signal circuits and intelligent transport systems. Before that, he specialsed in sonar designing, biomedical engineering and signal processing. Since 1995, he has been Head of Division of Circuits and Systems, School of EEE, NTU. He is a Fellow of IEE, UK, a Chartered Engineer (UK) and a Professional Engineer (Singapore).     

A full W-band low noise amplifier module for millimeter-wave applications

A full W-band Low Noise Amplifier (LNA) Module is designed and fabricated in this letter. A broadband transition is introduced in this module. The proposed transition is designed, optimized based on the results from numerical simulations. The results show that 1 dB bandwidth of the transition ranges from 61 to 117 GHz. For the purpose of verification, two transitions in back-to-back connection are measured. The results show that transmission loss is only about 0.9-1.7dB. This transition is used to interface integrated circuits to waveguide components. The characteristic of the LNA module is measured after assembly. It exhibits a broad bandwidth of 75 to 110 GHz , has a small signal gain above 21 dB. The noise figure is lower than 5dB throughout the entire W-band (below 3 dB from 89 to 95GHz) at a room temperature. The proposed LNA module exhibits potential for millimeter wave applications due to its high small signal gain, low noise, and low dc power consumption     

一种基于ZigBee应用的低功耗2.4GHz无线收发机

This paper presents a low power 2.4 GHz transceiver for ZigBee applications.This transceiver adopts low power system architecture with a low-IF receiver and a direct-conversion transmitter.The receiver consists of a new low noise amplifier(LNA) with a noise cancellation function,a new inverter-based variable gain complex filter (VGCF) for image rejection,a passive quadrature mixer,and a decibel linear programmable gain amplifier(PGA). The transmitter adopts a quadrature mixer and a class-B mode variable gain power amplifier(PA) to reduce power consumption.This transceiver is implemented in 0.18μm CMOS technology.The receiver achieves—95 dBm of sensitivity,28 dBc of image rejection,and -8 dBm of third-order input intercept point(IIP3).The transmitter can deliver a maximum of+3 dBm output power with PA efficiency of 30%.The whole chip area is less than 4.32 mm~2. It only consumes 12.63 mW in receiving mode and 14.22 mW in transmitting mode,respectively.     

Ultra low voltage, ultra low power low noise amplifier for 2 GHz applications

In this paper, a 0.29 V, 2 GHz CMOS low noise amplifier (LNA) intended for ultra low voltage and ultra low power applications is developed. The circuit is simulated in standard 0.18 μm CMOS MOSIS. A two-stage architecture is then used to simultaneously optimize the gain and noise performance. Using forward-body-biased, the proposed LNA can operate at 0.29 V supply voltage, successfully demonstrating the application potential of dynamic threshold voltage technology in the radio frequency region. The LNA provides a good gain of 26.25 dB, a noise figure of 2.202 dB, reverse isolation (S₁₂) of −59.04 dB, input return loss (S₁₁) of −122.66 dB and output return loss (S₂₂) of -11.61 dB, while consuming only 0.96mW dc power with an ultra low supply voltage of 0.29 V. To the best of authors’ knowledge this is the lowest voltage supply and the lowest power consumption CMOS LNA design reported for 2 GHz to date.     

Low power high gain CMOS LNA based on inverter cell and self-body bias for UWB receivers

A low-power low-noise amplifier (LNA) utilized a resistive inverter configuration feedback amplifier to achieve the broadband input matching purposes. To achieve low power consumption and high gain, the proposed LNA utilizes a current-reused technique and a splitting-load inductive peaking technique of a resistive-feedback inverter for input matching. Two wideband LNAs are implemented by TSMC 0.18 μm CMOS technology. The first LNA operates at 2–6 GHz. The minimum noise figure is 3.6 dB. The amplifier provides a maximum gain (S₂₁) of 18.5 dB while drawing 10.3 mW from a 1.5-V supply. This chip area is 1.028×0.921 mm². The second LNA operates at 3.1–10.6 GHz. By using self-forward body bias, it can reduce supply voltage as well as save bias current. The minimum noise figure is 4.8 dB. The amplifier provides a maximum gain (S₂₁) of 17.8 dB while drawing 9.67 mW from a 1.2-V supply. This chip area is 1.274×0.771 mm².