Enhanced swelling and responsive properties of an alginate-based superabsorbent hydrogel by sodium p-styrenesulfonate and attapulgite nanorods

In this work, a series of sodium alginate-g-poly(sodium acrylate-co-sodium p-styrenesulfonate)/attapulgite (NaAlg-g-poly(NaA-co-NaSS)/APT) superabsorbent composites were prepared by graft copolymerization using N,N’-methylenebisacrylamide (MBA) as a crosslinker and ammonium persulfate as an initiator. Fourier transform infrared spectroscopy revealed that NaA and NaSS had been grafted onto NaAlg, and APT participated in polymerization reaction through reactive –OH groups. The introduction of proper amount of NaSS and APT induced the improved surface morphology, swelling capacity, and swelling rate. Moreover, the swelling behaviors of the superabsorbent composites were remarkably influenced by various salt medium, pH buffer solutions and organic solvents, and especially an intriguing swelling–deswelling behavior was observed with altering water/organic solvent ratio.     

Synthesis,characterization and swelling behaviors of hydroxyethyl cellulose‐g‐poly(acrylic acid)/attapulgite superabsorbent composite

In this work, a series of novel hydroxyethyl cellulose‐ g‐poly(acrylic acid)/attapulgite (HEC‐g‐PAA/APT) superabsorbent composites were prepared through the graft polymerization of hydroxyethyl cellulose (HEC), partially neutralized acrylic acid (AA), and attapulgite (APT) in aqueous solution, and the composites were characterized by means of Fourier‐transform spectroscopy, scanning electron microscopy, and transmission electronmicroscopy. The effects of polymerization variables including concentrations of the initiator and crosslinker and APT content on water absorbency were studied, and the swelling properties in various pH solutions as well as the swelling kinetics in various saline solutions were also systematically evaluated. Results showed that the introduction of 5 wt% APT into HEC‐g‐PAA polymeric network could improve both water absorbency and water absorption rate of the superabsorbent composites. In addition, the superabsorbent composites retained high water absorbency over a wide pH range of 4–10, and the swelling kinetics of the superabsorbent composites in CaCl₂ and FeCl₃ solutions exhibited a remarkable overshooting phenomenon. POLYM. ENG. SCI., 2010. © 2010 Society of Plastics Engineers     

Synthesis and enhanced swelling properties of a guar gum-based superabsorbent composite by the simultaneous introduction of styrene and attapulgite

In current study, a series of novel guar gum-graft-poly(sodium acrylate-co-styrene)/attapulgite (GG-g-P(NaA-co-St)/APT) superabsorbent nanocomposites were prepared by the simultaneous graft copolymerization of partially neutralized acrylic acid (NaA), styrene (St) and attapulgite (APT) onto natural guar gum (GG), using ammonium persulfate (APS) as the initiator and N,N'-methylene-bis-acrylamide (MBA) as the crosslinking agent. Fourier Transform Infrared (FTIR) and ultravoilet (UV) spectra confirmed that NaA and St had been grafted onto GG backbones and APT participated in the polymerization reaction. The incorporation of St and APT clearly improved the surface porous morphology of the composites as exhibited by Filed Emission Scanning Electron Microscopy (FESEM). The effect of St and APT on the swelling properties and the swelling kinetics of the developed nanocomposite was investigated. Results showed that the simultaneous incorporation of proper amount of hydrophobic co-monomer St and inorganic nano-scale APT not only obviously enhanced the swelling capacity but highly improved the swelling rate, and the nanocomposite showed better salt-resistant capability and excellent pH-stability in various pH solutions.     

Synthesis and properties of poly(sodium acrylate‐co‐2‐acryloylamino‐2‐methyl‐1‐propanesulfonic acid)/attapulgite as a salt‐resistant superabsorbent composite

A novel salt‐resistant superabsorbent composite was prepared by copolymerization of partially neutralized acrylic acid, 2‐acryloylamino‐2‐methyl‐1‐propanesulfonic acid (AMPS) and attapulgite (APT). To enhance the swelling rate (SR) of the copolymer, sodium bicarbonate was used as a foaming agent in the course of copolymerization. Furthermore, for improving the properties of swollen hydrogel, such as strength, resilience and dispersion, the copolymer was surface‐crosslinked with glycerine and sodium silicate, and then the surface‐crosslinked copolymer was blended with aluminum sulfate and sodium carbonate in post treatment process. The influences of some reaction conditions, such as amount of AMPS, APT, and initiator, and neutralization degree of acrylic acid on water absorbency in 0.9 wt% NaCl aqueous solution both under atmospheric pressure (WA) and load (WA_P, P ≈ 2 × 10³ Pa) were investigated. In addition, the effect of them on SR was also studied. The WA and WA_P of the superabsorbent composite prepared under optimal conditions in 0.9 wt% NaCl aqueous solution were 52 g·g^?1 and 8 g·g^?1, respectively. Besides, the SR was fast, and it could reach 0.393 mL·(g·s)^?1. Moreover, the swollen hydrogel possessed excellent salt resistance, hydrogel resilience and dispersion. POLYM. ENG. SCI., 2009. © 2008 Society of Plastics Engineers     

Preparation and Swelling Behavior of a pH-Responsive Psyllium-g-Poly(acrylic acid)/Attapulgite Superabsorbent Nanocomposite

In this study, a series of psyllium-g-poly(acrylic acid)/attapulgite (PSY-g-PAA/APT) superabsorbent nanocomposites were prepared. The effects of the content of APT on equilibrium water absorption, swelling rate, and the swelling behaviors of the nanocomposites in various cationic saline solutions and different pH solutions were also systematically investigated. The nanocomposite containing 10 wt% APT gives the best water absorption of 568 g/g in distilled water and 64 g/g in 0.9 wt% NaCl solution. The excellent responsive properties and reversible On-Off switching characteristics can be observed in various pH buffer solutions.     

Superabsorbent composite. XIII. Effects of Al3+‐attapulgite on hydrogel strength and swelling behaviors of poly(acrylic acid)/Al3+‐attapulgite superabsorbent composites

Al³⁺‐attapulgite (Al³⁺‐APT) was prepared by treating attapulgite (APT) with AlCl₃ aqueous solution of various concentrations. The poly(acrylic acid)/Al³⁺‐attapulgite (PAA/Al³⁺‐APT) superabsorbent composite was prepared by reaction of partly neutralized acrylic acid, and Al³⁺‐APT in aqueous solution using N, N′‐methylenebisacrylamide as a crosslinker and ammonium persulfate as an initiator. The surface morphology of the composite was investigated by SEM, and the Al³⁺‐APT composite generated a relatively planar surface comparing the nature APT. The effects of Al³⁺‐APT on hydrogel strength and swelling behaviors, such as equilibrium water absorbency, swelling rate, and reswelling capability, of the superabsorbent composites were also studied. The hydrogel strength and reswelling capability were improved, however, the equilibrium water absorbency and swelling rate decreased with increasing AlCl₃ solution concentration. The equilibrium water absorbency firstly increased, and then decreased with increasing Al³⁺‐APT content. The results indicate that Al³⁺‐APT acts as an assistant crosslinker in the polymeric network, which has great influences on hydrogel strength and swelling behaviors of the PAA/Al³⁺‐APT superabsorbent composites. POLYM. ENG. SCI., 47:619–624, 2007. © 2007 Society of Plastics Engineers.     

Study on superabsorbent composite. VIII. Effects of acid‐ and heat‐activated attapulgite on water absorbency of polyacrylamide/attapulgite

A novel superabsorbent composite, polyacrylamide/attapulgite, from acrylamide (AM) and attapulgite (APT), was prepared by free‐radical polymerization, using N,N′‐methylenebisacrylamide (MBA) as a crosslinker and ammonium persulfate (APS) as an initiator. The effects of hydrochloric acid (HCl) concentration, acidification time, and acidification temperature while acidifying APT and temperature and APT heat‐activation on water absorbency of the superabsorbent composite in distilled water and in 0.9 wt % NaCl solution were studied. The water absorbency first decreases with increasing the HCl concentration while acidifying APT, and then increases with further increasing the HCl concentration. Prolongation of acidification time is of benefit to the increase of water absorbency. At a given HCl concentration, water absorbency for the composite increases with increasing acidification temperature. An important increase in water absorbency was observed after incorporating heat‐activated APT into the polymeric network, reaching a maximum of 1964 g g^?1 with the APT heat‐activated at 400°C. Acid‐ and heat‐activation can influence chemical composition, crystalline structure, cation exchange capacity (CEC), and specific surface area of APT according XRF, XRD, FTIR analysis, and physicochemical properties test, and then on water absorbency of corresponding PAM/APT superabsorbent composite. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 2419–2424, 2007     

Synthesis of an alginate–poly(sodium acrylate‐co‐acrylamide) superabsorbent hydrogel with low salt sensitivity and high pH sensitivity

This article describes the synthesis and swelling behavior of a superabsorbing hydrogel based on sodium alginate (NaAlg) and polyacrylonitrile (PAN). The physical mixture of NaAlg and PAN was hydrolyzed with a solution of NaOH to yield an alginate–poly(sodium acrylate‐co‐acrylamide) [Alg–poly(NaAA‐co‐AAm)] superabsorbent hydrogel. A proposed mechanism for hydrogel formation was suggested, and the structure of the product was established with Fourier transform infrared spectroscopy. The effects of reaction variables were systematically optimized to achieve a hydrogel with a swelling capacity as high as possible. Under the optimized conditions concluded, the maximum capacity of swelling in distilled water was 610 g/g. The absorbency of the synthesized hydrogels was also measured in various salt solutions. The swelling ratios decreased with an increase in the ionic strength of the salt solutions. In addition, the swelling capacity was determined in solutions with pHs ranging from 1 to 13. The Alg–poly(NaAA‐co‐AAm) hydrogel exhibited pH responsiveness, so a swelling–deswelling pulsatile behavior was recorded at pHs 2 and 8. This on–off switching behavior made the hydrogel as a good candidate for the controlled delivery of bioactive agents. Finally, the swelling kinetics of the hydrogels with various particle sizes were preliminarily investigated as well. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 2927–2937, 2006     

Preparation and slow‐release property of a poly(acrylic acid)/attapulgite/sodium humate superabsorbent composite

A novel poly(acrylic acid)/attapulgite (APT)/sodium humate (SH) superabsorbent composite was synthesized through the graft copolymerization reaction of acrylic acid on APT micropowder and SH with N,N′‐methylene bisacrylamide as a crosslinker and ammonium persulfate as an initiator in an aqueous solution. Various effects on the water absorbency, including the amounts of the crosslinker, initiator, APT, and SH, were investigated. The superabsorbent composite was characterized with Fourier transform infrared spectroscopy and scanning electron microscopy. The superabsorbent composite synthesized under optimal synthesis conditions with an APT concentration of 20% and an SH concentration of 20% exhibited absorption of 583 g of H₂O/g of sample and 63 g of H₂O/g of sample in distilled water and in a 0.9 wt % NaCl solution, respectively. The slow‐release property of SH from the superabsorbent composite into water was measured, and a test of the water retention of the superabsorbent composite in soil was also carried out experimentally with and without the superabsorbent composite. The results showed that the superabsorbent composite had not only good water retention but also an additional slow‐release property of SH. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 37–45, 2007     

Study on superabsorbent composite. XV. Effects of ion‐exchanged attapulgite on water absorbency of superabsorbent composites

A series of superabsorbent composite, polyacrylamide/attapulgite, from acrylamide (AM) and ion‐exchanged attapulgite (APT) was prepared by aqueous polymerization, using N,N′‐methylenebisacrylamide (MBA) as a crosslinker and ammonium persulfate (APS) as an initiator. The effects of ion‐exchanged APT on water absorbency of superabsorbent composites in distilled water and in 0.9 wt% NaCl solution were studied. The result indicates that higher cation‐exchange capacity (CEC) and lower specific surface area (SSA) of APT treated with various anions are of benefit for improving water absorbency in distilled water. The effects of AlCl₃ solution concentration and Al³⁺‐exchanged APT content on water absorbency of the composite were also investigated. The concentration of AlCl₃ solution has a great influence on water absorbency of the superabsorbent composite. Al³⁺‐exchange of APT could also enhance reswelling ability of the corresponding composite, which indicates that Al³⁺‐exchange of APT could improve gel strength and gives a direct evidence for its acting as an inorganic assistant crosslinker in the polymeric network. POLYM. COMPOS., 28:208–213, 2007. © 2007 Society of Plastics Engineers     

Preparation and properties of porous poly(sodium acrylate‐co‐acrylamide) salt‐resistant superabsorbent composite

A novel semi‐interpenetrating polymer networks (semi‐IPNs) porous salt‐resistant superabsorbent composite was prepared by copolymerization of partially neutralized acrylic acid and acrylamide using polyethylene glycol as semi‐IPNs composite, N,N′‐methylenebisacrylamide, triene propanol phosphate, and trihydroxymethyl propane glycidol ether as crosslinking agents, methanol, propanol, and butanol as foaming agents, and L ‐ascorbic acid and peroxide hydrogen as initiators. To improve the properties of swollen hydrogel, such as strength, resilience, permeabilities, and dispersion, the copolymer was surface‐crosslinked, and then blended with aluminum sulfate, sodium carbonate, and sodium 1‐octadecanol phosphate in the course of post treatment. The influences of reaction conditions on properties of superabsorbent composite were investigated and optimized, and the water absorbency of superabsorbent composite prepared at optimal conditions in 0.9 wt% NaCl aqueous solution under atmospheric pressure and certain load (P ≈ 2 × 10³ Pa) were 61 g g^?1 and 16.7 g g^?1, respectively. Moreover, the swelling rate reached 22.003 × 10^?3 g (g s)^?1. And the excellent hydrogel properties, such as hydrogel strength, resilience, permeabilities, and dispersion were also obtained. POLYM. ENG. SCI., 2011. © 2011 Society of Plastics Engineers     

Study on superabsorbent composite XXV. Synthesis,characterization, and swelling behaviors of poly(acrylic acid‐co‐N‐acryloylmorpholine)/attapulgite superabsorbent composites

In this work, a novel poly(acrylic acid‐co‐N‐acryloylmorpholine)/attapulgite superabsorbent composite was prepared by graft copolymerization among acrylic acid, N‐acryloylmorpholine and attapulgite in aqueous solution, using N,N′‐methylenebisacrylamide as a crosslinker and ammonium persulfate as an initiator. The result from FTIR spectra showed that  OH of attapulgite participated in graft copolymerization with acrylic acid and N‐acryloylmorpholine. Proper monomer ratio and atapulgite content could form a loose surface, and improve reswelling ability and initial swelling rate. The buffer action of the  COOH and  COO⁻ groups in the superabsorbent composite keeps the water absorbency a rough constant in the pH range of 4.4–9.6. Both polarity and structure of an organic solvent are responsible for the phase transition point of the superabsorbent composite. POLYM. COMPOS., 2010. © 2009 Society of Plastics Engineers     

Hydroxyethyl chitosan‐g‐poly(acrylic acid‐co‐sodium acrylate) superabsorbent polymers

A novel hydroxyethyl chitosan‐g‐poly(acrylic acid‐co‐Sodium Acrylate) (HECTS‐g‐(PAA‐co‐PSA)) superabsorbent polymer was prepared through graft copolymerization of acrylic acid and sodium acrylate onto the chain of hydroxyethyl chitosan. The structure of the polymer was characterized by FTIR. By studying the water absorption of the polymer synthesized under different conditions, the optimal conditions for synthesizing the polymer with the highest swelling ratio was defined. This superabsorbent polymer was further treated by the solvent precipitation method and by the freeze‐drying method. We found that the water absorption rate of the treated polymer was greatly increased and the microstructure of the treated polymer was changed from small pores to loose macro pores. The swelling processes of the polymers before and after modification fit first‐order dynamic processes. The amount of the residual acrylic acid was greatly decreased after treatments. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Preparation of starch‐graft‐poly(acrylamide)/attapulgite superabsorbent composite

A novel starch‐graft‐poly(acrylamide)/attapulgite superabsorbent composite was synthesized by graft copolymerization reaction of starch, acrylamide (AM), and attapulgite micropowder using N.N‐methylene‐bisacrylamide (MBA) as a crosslinker and ammonium persulphate (APS) as an initiator in aqueous solution, followed by hydrolysis with sodium hydroxide. The effects on water absorbency, such as amount of crosslinker, initiator, attapulgite, weight ratio of acrylamide to starch in the feed, gelatinization conditions of starch and molar ratio of NaOH to acrylamide, and so forth, were investigated. These superabsorbent composites were characterized by Fourier transform infrared spectroscopy (FTIR) and thermogravimetric analysis (TGA). The water absorbencies for these superabsorbent composites in water and saline solution were investigated, and water retention tests were carried out. Results obtained from this study showed that the water absorbency of superabsorbent composite synthesized under optimal synthesis conditions with an attapulgite content of 10% exhibit absorption of 1317 g H₂O/g sample and 68 g H₂O/g sample in distilled water and in 0.9 wt % NaCl solution, respectively. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 1351–1357, 2005     

Preparation of polyacrylamide/graphite oxide superabsorbent nanocomposites with salt tolerance and slow release properties

Novel polyacrylamide/graphite oxide (PAM/GO) superabsorbent nanocomposites were synthesized by a simple solution polymerization of acrylamide using N,N ′‐methylenebisacrylamide as crosslinker and ammonium persulfate as initiator. The well dispersion of GO nanoplatelets in the polymeric network results in a remarkable improvement on the comprehensive swelling performance of the resulting superabsorbent nanocomposites. The water absorption experimental results show that the superabsorbent nanocomposites could absorb water as twice as that of crosslinked polyacrylamide (PAM) superabsorbent with a weight gain of 400 g g^?1 with a low loading of GO. The salt tolerance and water‐retention ability of the resulting PAM/GO superabsorbent nanocomposites are also enhanced compared with PAM. Moreover, by embedding of ammonium salt into PAM/GO network, the PAM/GO superabsorbent nanocomposites also exhibit a slow release behavior of ammonium salt from network when swelling in water, which makes the PAM/GO superabsorbent nanocomposites multifunctional absorbent materials with great potential for agricultural and horticultural applications. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Superabsorbent composite. X. Effects of saponification on properties of polyacrylamide/attapulgite

A novel superabsorbent composite from acrylamide (AM) and attapulgite (APT), polyacrylamide/attapulgite (PAM/APT), was prepared by polymerizing AM with the existence of APT in aqueous solution, and then saponified with NaOH solution. Considering the impacts of hydrophilic groups (? COONa, ? COOH, and ? CONH₂) on properties of the PAM/APT composite, the effects of saponification mode, molar ratio of NaOH to AM and saponification time on water absorbency, hydrophilic group content, and surface morphology were investigated systematically. The results indicate that the two‐step adding NaOH mode is superior to that of the one‐step mode. Among the superabsorbent composite incorporated with 30 wt% APT, the composite saponified at 95°C for 2 h with the molar ratio of 0.6 for NaOH to AM acquired the highest water absorbencies of 1715g g^?1 and 87.8g g^?1 in distilled water and in 0.9 wt% NaCl solution, respectively. The molar ratio of various hydrophilic groups at this time was 10:3:11 for ? COONa, ? COOH, and ? CONH₂ determined using linear potentiometric titration method. POLYM. ENG. SCI. 46:1762–1767, 2006. © 2006 Society of Plastics Engineers.     

Effect of attapulgite contents on release behaviors of a pH sensitive carboxymethyl cellulose‐g‐poly(acrylic acid)/attapulgite/sodium alginate composite hydrogel bead containing diclofenac

A series of pH‐sensitive composite hydrogel beads, carboxymethyl cellulose‐g‐poly(acrylic acid)/attapulgite/sodium alginate (CMC‐g‐PAA/APT/SA), were prepared by combining CMC‐g‐PAA/APT composite and SA, using Ca²⁺ as the ionic crosslinking agent and diclofenac sodium (DS) as the model drug. The effects of APT content and external pH on the swelling properties and release behaviors of DS from the composite hydrogel beads were investigated. The results showed that the composite hydrogel beads exhibited good pH‐sensitivity. Introducing 20% APT into CMC‐g‐PAA hydrogel could change the surface structure of the composite hydrogel beads, decrease the swelling ability, and relieve the burst release effect of DS. The drug cumulative release ratio of DS from the hydrogel beads in simulated gastric fluid was only 3.71% within 3 hour, but in simulated intestinal fluid about 50% for 3 hour, 85% for 12 hour, up to 90% after 24 hour. The obtained results indicated that the CMC‐g‐PAA/APT/SA hydrogel beads could be applied to the drug delivery system as drug carriers in the intestinal tract. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Influences of compatibilizers on rheology and mechanical properties of propylene random copolymer/styrene‐ethylene‐butylene‐styrene block copolymer/organic‐montmorillonite nanocomposites

Propylene random copolymer (PPR)/styrene‐ethylene‐butylene‐styrene block copolymer (SEBS)/compatibilizer/organic‐montmorillonite (OMMT) quaternary nanocomposites and PPR/compatibilizer/OMMT ternary nanocomposites were prepared via two‐stage melt blending and influences of compatibilizers, maleic anhydride (MA) grafted styrene‐ethylene‐butylene‐styrene copolymer (SEBS‐g‐MA), poly(octene‐co‐ethylene) (POE‐g‐MA), or propylene block copolymers (PPB‐g‐MA), on rheology and mechanical properties of the nanocomposites were investigated. The results of X‐ray diffraction measurement and transmission electron microscopy observation showed that OMMT layers were mainly intercalated in the nanocomposites except for the mainly exfoliated structure in the quaternary nanocomposites using POE‐g‐MA as compatibilizer. The nanocomposites exhibited pseudo‐solid like viscoelasticity in low frequencies and shear‐thinning in high shear rates. As far as OMMT dispersion was concerned, POE‐g‐MA was superior to SEBS‐g‐MA and PPB‐g‐MA, which gives rise to the highest viscosities in both the ternary and quaternary nanocomposites. The quaternary nanocomposites containing POE‐g‐MA were endowed with balanced toughness and rigidity. It was suggested that a suitable combination of compatibilizer and SEBS was an essentially important factor for adjusting the OMMT dispersion and distribution, the rheological and mechanical performances of the nanocomposites. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Study on superabsorbent composite. XX. Effects of cation‐exchanged montmorillonite on swelling properties of superabsorbent composite containing sodium humate

In this work, the effects of different cation‐exchanged montmorillonite on water absorbency of poly(acrylic acid‐co‐acrylamide)/montmorillonite/sodium humate (PAA‐AM/MMT/SH) superabsorbent composite were systematically investigated under the same preparation conditions. The superabsorbents doped with different cation‐exchanged montmorillonite were characterized by Fourier‐transform infrared spectroscopy, X‐ray diffraction, and scanning electron microscopy technologies. Swelling behaviors of developing superabsorbent composite in various cationic saline solutions (NaCl, CaCl₂, and FeCl₃) were also investigated. The water absorbencies of superabsorbent composite with 20 wt% MMT and 30 wt% SH are 638, 723, 682, and 363 g g⁻¹ in distilled water for incorporating natural Na⁺‐MMT, Li⁺‐exchanged MMT, Ca²⁺‐exchanged MMT, and Al³⁺‐exchanged MMT, respectively. The results showed that the cation‐exchange process had some obvious influences on final water absorbency of superabsorbent composite. NaCl, CaCl₂, and FeCl₃ solutions did not alter the swelling characteristics of the superabsorbent materials at a concentration of less than 0.01 mM, however, a concentration of greater than 0.1 mM caused a collapse in the swelling curves. The excellent swelling‐reswelling‐swelling behavior and lower swelling rate testified that Al³⁺‐exchanged MMT can act as an assistant crosslinker in the polymeric network. POLYM. COMPOS., 2009. © 2008 Society of Plastics Engineers     

Synthesis and characterization of poly(HEMA‐co‐MMA)‐g‐POSS nanocomposites by combination of reversible addition fragmentation chain transfer polymerization and click chemistry

New hybrid poly(hydroxyethyl methacrylate‐co‐methyl methacrylate)‐g‐polyhedral oligosilsesquioxane [poly(HEMA‐co‐MMA)‐g‐POSS] nanocomposites were synthesized by the combination of reversible addition fragmentation chain transfer (RAFT) polymerization and click chemistry using a grafting to protocol. Initially, the random copolymer poly(HEMA‐co‐MMA) was prepared by RAFT polymerization of HEMA and MMA. Alkynyl side groups were introduced onto the polymeric backbones by esterification reaction between 4‐pentynoic acid and the hydroxyl groups on poly(HEMA‐co‐MMA). Azide‐substituted POSS (POSS? N₃) was prepared by the reaction of chloropropyl‐heptaisobutyl‐substituted POSS with NaN₃. The click reaction of poly(HEMA‐co‐MMA)‐alkyne and POSS? N₃ using CuBr/PMDEATA as a catalyst afforded poly(HEMA‐co‐MMA)‐g‐POSS. The structure of the organic/inorganic hybrid material was investigated by Fourier transformed infrared, ¹H‐NMR, and ²⁹Si‐NMR. The elemental mapping analysis of the hybrid using X‐ray photoelectron spectroscopy and EDX also suggest the formation of poly(HEMA‐co‐MMA)‐anchored POSS nanocomposites. The XRD spectrum of the nanocomposites gives evidence that the incorporation of POSS moiety leads to a hybrid physical structure. The morphological feature of the hybrid nanocomposites as captured by field emission scanning electron microscopy and transmission electron microscopic analyses indicate that a thick layer of polymer brushes was immobilized on the POSS cubic nanostructures. The gel permeation chromatography analysis of poly(HEMA‐co‐MMA) and poly(HEMA‐co‐MMA)‐g‐POSS further suggests the preparation of nanocomposites by the combination of RAFT and click chemistry. The thermogravimetric analysis revealed that the thermal property of the poly(HEMA‐co‐MMA) copolymer was significantly improved by the inclusion of POSS in the copolymer matrix. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013