The preparation of microporous membranes from blends of poly(2,6‐dimethyl‐1,4‐phenylene oxide) and sulfonated poly(2,6‐dimethyl‐1,4‐phenylene oxide)

Poly(2,6‐dimethyl‐1,4‐phenylene oxide) (PPO) is a chemically resistant polymer and, therefore, an attractive material for the formation of membranes. However, membranes of unmodified PPO prepared by an immersion precipitation possess very low hydraulic permeabilities at the filtration processes. The membranes with higher hydraulic permeabilities can be prepared from sulfonated PPO and/or from blends of unsulfonated PPO and sulfonated PPO. In conclusion, the mechanism of the formation of membranes from blends of unsulfonated PPO and sulfonated PPO is suggested. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 73: 161–167, 1999     

High‐resolution thermogravimetry of poly(2,6‐dimethyl‐1,4‐phenylene oxide)

The thermal degradation and kinetics of poly(2,6‐dimethylphenylene oxide) (PPO) were studied by high‐resolution thermogravimetry. The thermogravimetry measurements were conducted at an initial heating rate of 50°C min⁻¹, resolution 4.0, and sensitivity 1.0 in both nitrogen and air from room temperature to 900°C. A two‐step degradation process was clearly revealed in air at the temperatures of 430°C and 521°C. The thermal degradation temperatures and kinetic parameters of the PPO appear to be higher in air than in nitrogen, indicative of a higher thermostability in air. The temperature, activation energy, order, and frequency factor of the thermal degradation of the PPO in nitrogen are 419°C, 100–120 kJ mol⁻¹, 0.5, and 13–17 min⁻¹, respectively. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 71: 1887–1892, 1999     

Synthesis,characterization, and UV‐curing properties of silicon‐containing (Meth)acrylate monomers

Eight different silicon‐containing (meth)acrylate monomers are synthesized by the substitution reaction of chlorosiloxanes with 2‐hydroxyethyl methacrylate or 2‐hydroxyethyl acrylate. Their molecular structures are confirmed by IR, ¹H‐NMR, and ¹³C‐NMR spectroscopic analyses. The effects of silicon content on the UV‐curing behavior, physical, surface, and thermal properties are investigated. The UV‐curing behavior is analyzed by photo differential scanning calorimetry. The surface free energy of the UV‐cured film is calculated from contact angles measured using the Lewis acid‐base three liquids method. The silicon‐containing (meth)acrylate monomers perform much better than traditional (meth)acrylate monomers on UV‐curing. The silicon‐containing monomers have higher final conversions and fast UV‐curing rates in photopolymerization. The surface free energy decreases with increasing silicon content, because silicon in the soft segment is transferred to the surface, producing a UV‐cured film; this is confirmed by X‐ray photoelectron spectroscopy measurements. All these advantageous properties enable these synthetic silicon‐containing monomers to perform better in applications. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Synthesis and characterization of a poly(ether–ester) copolymer from poly(2,6 dimethyl‐1,4‐phenylene oxide) and poly(ethylene terephthalate)

A series of poly(ether–ester) copolymers were synthesized from poly(2,6 dimethyl‐1,4‐phenylene oxide) (PPO) and poly(ethylene terephthalate) (PET). The synthesis was carried out by two‐step solution polymerization process. PET oligomers were synthesized via glycolysis and subsequently used in the copolymerization reaction. FTIR spectroscopy analysis shows the coexistence of spectral contributions of PPO and PET on the spectra of their ether–ester copolymers. The composition of the poly(ether–ester)s was calculated via ¹H NMR spectroscopy. A single glass transition temperature was detected for all synthesized poly(ether–ester)s. T_g behavior as a function of poly(ether–ester) composition is well represented by the Gordon‐Taylor equation. The molar masses of the copolymers synthesized were calculated by viscosimetry. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci, 2006     

Characterization of polymer systems based on sulfonated poly(2,6‐dimethyl‐1,4‐phenylene oxide)

The sulfonation reaction of poly(2,6‐dimethyl‐1,4‐phenylene oxide) (PPO) has been carried out, incorporating the resulting product into pure PPO to study, in forthcoming research, the electrical and mechanical features of the composites with regard to their performance in fuel cells. Pure sulfonated polymers and their blends have been characterized from a microstructural and electrical point of view, by means of X‐ray photoelectron spectroscopy (XPS), differential scanning calorimetry (DSC) and complex impedance spectroscopy. Membranes have been manufactured with excellent ionic conductivity at room temperature. © 2000 Society of Chemical Industry     

Phase behavior of binary and ternary blends of poly(styrene‐co‐methacrylic acid), poly(styrene‐co‐4‐vinylpyridine), and poly(2,6‐dimethyl‐1,4‐phenylene oxide)

Poly(styrene‐co‐methacrylic acid) (PSMA) and poly(styrene‐co‐4‐vinylpyridine) (PS4VP) of different compositions were prepared and characterized. The phase behavior of these copolymers as binary PSMA/PS4VP mixtures or with poly(2,6‐dimethyl‐1,4‐phenylene oxide) (PPO) as PPO/PSMA or PPO/PS4VP and PPO/PSMA/PS4VP ternary blends was investigated by differential scanning calorimetry (DSC). This study showed that PPO was miscible with PS4VP containing up to 15 mol % 4‐vinylpyridine (4VP) but immiscible with PS4VP‐30 (where the number following the hyphen refers to the percentage 4VP in the polymer) and PSMA‐20 (where the number following the hyphen refers to the percentage methacrylic acid in the polymer) over the entire composition range. To examine the morphology of the immiscible blends, scanning electron microscopy was used. Because of the hydrogen‐bonding specific interactions that occurred between the carboxylic groups of PSMA and the pyridine groups of PS4VP, chloroform solutions of PSMA‐20 and PS4VP‐15 formed interpolymer complexes. The obtained glass‐transition temperatures (T_g's) of the PSMA‐20/PS4VP‐15 complexes were found to be higher than those calculated from the additivity rule. Although, depending on the content of 4VP, the shape of the T_g of the PPO/PS4VP blends changed from concave to S‐shaped in the case of the miscible blends, two T_g were observed with each PPO/PS4VP‐30 and PPO/PS4VP‐40 blend. The thermal stability of the PSMA‐20/PS4VP‐15 interpolymer complexes was studied by thermogravimetry. On the basis of the obtained results, the phase behavior of the ternary PPO/PSMA‐20/PS4VP‐15 blends was investigated by DSC. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Synthesis of low molecular weight poly(vinyl acetate) and its application as plasticizer

Poly(vinyl acetate), PVAc, with a degree of polymerization X_n = 10 was prepared by chain‐transfer radical polymerization using carbon tetrachloride and used as oligomeric plasticizer for commercial PVAc. However, the chlorinated chain ends cause a low thermal stability requiring mild Cl/H substitution. The product exhibits high thermal stability and excellent melt‐compounding properties. Blends of oligomeric and commercial PVAc show single glass transition temperatures which decrease with higher oligomer content and exhibit small negative deviations from Fox' linear additivity rule. This indicates plasticization and miscibility being mainly due to entropic effects. Injection‐moulded thick specimens show ductile behaviour at oligomer contents >10 wt %, while sheets with a thickness of 0.2–0.5 mm appear flexible already at 7.5 wt %. The oxygen permeability coefficients are an order of magnitude lower than those of low‐density polyethylene. Due to the sum of their properties, the plasticized sheets present a promising alternative in the preparation of barrier materials. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40226.     

Microporous membranes prepared from blends of polysulfone and sulfonated poly(2,6‐dimethyl‐1,4‐phenylene oxide)

Membranes were prepared from solutions containing Udel‐type polysulfone (PSf) and sulfonated poly(2,6‐dimethyl‐1,4‐phenylene oxide) (SPPO). Polymer solutions in 1‐methyl‐2‐pyrrolidone were cast on a nonwoven textile and precipitated in a water bath. The permeabilities and selectivities of the prepared membranes depended on the concentrations of both polymers in the casting solution. The higher the concentration of PSf, the lower were the permeabilities to water and average pore sizes of the membranes. On the other hand, a very small amount of SPPO in the casting solution (about 1–4 wt % relative to the casting solution weight) brought about a considerable increase in water permeabilities and had a small influence on the average pore sizes. The effects were most pronounced if SPPO with a degree of sulfonation of 20–40% was used. The considerable increase in water permeabilities was explained by separation of the PSf and SPPO phases during precipitation in water and by the concentration of hydrophilic SPPO on the surface of the membrane and its pores. The determinations of the oriented concentration potentials proved the presence of a negative surface charge in the membranes. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 134–142, 2001     

Synthesis of syndiotactic poly(methacrylic acid) by free‐radical polymerization of the pseudo‐divinyl monomer formed with methacrylic acid and catechol

Syndiotactic poly(methacrylic acid) (Syn‐PMAA, r diad = 91 mol %) was synthesized by free radical polymerization of methacrylic acid (MAA) with catechol. The pseudo‐divinyl monomer was formed with one catechol and two MAA molecules by the hydrogen bonding between OH groups of catechol and COOH group of MAA. When the free radical polymerization of the pseudo‐divinyl monomer was carried out, intra‐ and intermolecular addition proceeded with racemic addition. The hydrogen bonding was the driving force to control tacticity. We discussed the effects of solvent, temperature, and the concentrations of MAA and catechol on the pseudo‐divinyl monomer formation. The highly syndiotactic PMAA was successfully obtained. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Influence of an oligomer polyol and monomers on the structure and properties of core–shell polyurethane–poly(n‐butyl acrylate‐co‐styrene) hybrid emulsions

The free‐radical polymerization of alkenyl‐terminated polyurethane dispersions with styrene and n‐butyl acrylate was performed to obtain a series of stable polyurethane–poly(n‐butyl acrylate‐co‐styrene) (PUA) hybrid emulsions. The core–shell structure of the emulsions was observed by transmission electron microscopy, and the microstructure was studied by ¹H‐NMR and Fourier transform infrared spectroscopy. The effects of the poly(propylene glycol)s (number‐average molecular weights = 1000, 1500, and 2000 Da) and the mass ratios of polyurethane to poly(n‐butyl acrylate‐co‐styrene) (PBS; 50/50, 40/60, 30/70, 20/80, and 10/90) on the structure, morphology, and properties of the PUAs were investigated. The average particle size and water absorption values of the PUAs increased with increasing of PBS content. However, the surface tension decreased from 34.61 to 30.29 mN/m. PUA‐2, with a bimodal distribution, showed Newtonian liquid behaviors, and PUA‐3 showed a great thermal stability, fast drying characteristics, and excellent adhesion to packaging films. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43763.     

Proton exchange composite membranes from blends of brominated and sulfonated poly(2,6‐dimethyl‐1,4‐phenylene oxide)

New composite proton exchange membrane was prepared by mixing a 1‐methyl‐2‐pyrrolidone (NMP) solution of sulfonated poly(2,6‐dimethyl‐1,4‐phenylene oxide) (SPPO) in sodium form and brominated poly(2,6‐dimethyl‐1,4‐phenylene oxide) (BPPO) for hydrophilic‐hydrophobic balance, then casting the solution as a thin film, evaporating the solvent, and treating the membrane with aqueous hydrochloric acid. The resulting membranes were subsequently characterized using FTIR‐ATR, SEM‐EDXA, and TGA instrumentation as well as measurements of basic properties such as ion exchange capacity (IEC), water uptake, proton conductivity, methanol permeability, and single cell performance. Water uptake, IEC, proton conductivity, and methanol permeability all increased with a corresponding increase of SPPO content. By properly compromising the conductivity and methanol permeability, membranes with 60–80 wt % SPPO content exhibited comparable proton conductivity to that of Nafion^® 117, with only half the methanol permeability, thereby demonstrating higher single cell performance. The membranes developed in this study could thus be a suitable candidate electrolyte for proton exchange membrane fuel cells (PEMFCs). © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Effects of polymer molecular weight and chemical modification on the gas transport properties of poly(2,6‐dimethyl‐1,4‐phenylene oxide)

Poly(2,6‐dimethyl‐1,4‐phenylene oxide) (PPO) of different intrinsic viscosities has been studied to understand the effect of polymer molecular weight on the permeability and permeability ratio of CO₂/CH₄ and O₂/N₂ gas pairs. The increase in permeability of dense films prepared from higher molecular weight PPO was explained in terms of increased free volume. Gas permeability for the high molecular weight was further improved by attaching bulky bromine groups to the phenyl ring of the PPO backbone. Permeability ratio of PPO was greatly improved by attaching polar groups such as —COOH or —SO₃H. The loss in permeability because of the presence of the polar groups was compensated by using PPO that was brominated and sulfonated. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 1137–1143, 2000     

Effect of swelling agent on the molecular weight of poly(2,6‐dimethyl‐1,4‐phenylene oxide) synthesized in an aqueous medium

The effects of the species and content of a swelling agent on the molecular weight of poly(2,6‐dimethyl‐1,4‐phenylene oxide) (PPO) synthesized in an aqueous medium were studied. It was found that the molecular weight of PPO increases after introducing a certain amount of the swelling agent during the oxidative polymerization of 2,6‐dimethylphenol (DMP). T_g of the PPO/swelling agent mixture decreases with the increase of the swelling agent content, and the relation between T_g of the PPO/swelling agent mixture and the swelling agent content obeys Fox equation. After the introduction of the swelling agent during the oxidative polymerization of DMP, the molecular weight of PPO is correlated with T_g of the PPO/swelling agent mixture and it was revealed that T_g plays an important role in the molecular weight of PPO synthesized in the aqueous medium. The same molecular weight of PPO can be obtained only if T_g of the PPO/swelling agent mixture is the same, no matter what kind of swelling agent is introduced during the oxidative polymerization of DMP. POLYM. ENG. SCI., 2008. © 2008 Society of Plastics Engineers     

Miscibility and specific interactions in blends of poly(vinyl phenyl ketone hydrogenated) with poly(2,6‐dimethyl‐1,4‐phenylene oxide)

The miscibility behavior of poly(vinyl phenyl ketone hydrogenated) (PVPhKH) and poly(2,6‐dimethyl‐1,4‐phenylene oxide) (PPO) are studied by differential scanning calorimetry, thermomechanical analysis, and FTIR spectroscopy. Two miscibility windows between 10 to 40 and 60 to 90 wt % PPO are detected. Only the blend with 50 wt % PPO is immiscible. The best fit of the Gordon–Taylor equation of the experimental glass‐transition temperatures for miscible PVPhKH/PPO blends is shown. A study by FTIR spectroscopy suggests that hydrogen bonding interactions are formed between the hydroxyl groups of PVPhKH and the ether groups of PPO. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 1887–1892, 2004     

Blends of SBS triblock copolymer with poly(2,6‐dimethyl‐1,4‐phenylene oxide)/polystyrene mixture

Blends of styrene–butadiene–styrene (SBS) or styrene–ethylene/1‐butene–styrene (SEBS) triblock copolymers with a commercial mixture of polystyrene (PS) and poly(2,6‐dimethyl‐1,4‐phenylene oxide) (PPO) were prepared in the melt at different temperatures according to the chemical kind of the copolymer. Although solution‐cast SBS/PPO and SBS/PS blends were already known in the literature, a general and systematic study of the miscibility of the PS/PPO blend with a styrene‐based triblock copolymer in the melt was still missing. The thermal and mechanical behavior of SBS/(PPO/PS) blends was investigated by means of DSC and dynamic thermomechanical analysis (DMTA). The results were then compared to analogous SEBS/(PPO/PS) blends, for which the presence of a saturated olefinic block allowed processing at higher temperatures (220°C instead of 180°C). All the blends were further characterized by SEM and TGA to tentatively relate the observed properties with the blends' morphology and degradation temperature. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 2698–2705, 2003     

Ion‐exchange membranes prepared by blending sulfonated poly(2,6‐dimethyl‐1,4‐phenylene oxide) with polybenzimidazole

New ion‐exchange acid/base‐blend (SPPO/PBI) membranes were prepared by mixing N,N‐dimethylacetamide (DMA) solutions of sulfonated poly(2,6‐dimethyl‐1,4‐phenylene oxide) (SPPO) in the ammonium form and of polybenzimidazole (PBI), casting the solution as a thin film, evaporating the solvent, and treating the membrane with aqueous hydrochloric acid. The resulting membranes were found insoluble in DMA. The preliminary tests of the membranes were carried out in an H₂/O₂ fuel cell at room temperature. Their performance in the fuel cell increased with the increase in the concentration of SPPO sulfonic acid groups in the blend, but the membranes formed with the highly sulfonated SPPO alone or predominanting, which swelled excessively in water, did not give reproducible results, and their performance was usually inferior to that of the membranes having an optimum ratio of both components. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 1118–1127, 2002     

Synthesis and characterization of hydroxy‐terminated polyether‐polydimethylsiloxane‐polyether (PE‐PDMS‐PE) triblock oligomers and their use in the preparation of thermoplastic polyurethanes

A series of hydroxy‐terminated polyether‐polydimethylsiloxane‐polyether (α,ω‐dihydroxy‐(PE‐PDMS‐PE)) ABA triblock oligomers were synthesized from silanic fluids and methyl polyallyloxide polyethers. The reaction was a one‐step solventless hydrosilylation reaction with chloroplatinic acid (CPA) catalyst in the presence of heat. These ABA oligomers were characterized via ¹H‐NMR, ¹³C‐NMR, ²⁹Si‐NMR, FT‐IR, and GPC to demonstrate that they exhibit a 100% linear ABA structure with a siloxane Si? O chain in the center and polyether ethylene oxide (EO)/propylene oxide (PO) chains on the two sides terminated by hydroxy groups. The triblock oligomers were used to form thermoplastic polyurethanes (TPUs) using two‐step solventless bulk polymerization. The investigation of triblock oligomers impact on TPUs mechanical properties, thermal performance, surface water repellency, and morphology performance were analyzed by Instron material tester, differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), water contact angles (WCA), scanning electron microscope (SEM), and transmission electron microscope (TEM). DSC and TGA indicated that PE‐PDMS‐PE modified TPUs had a clear lower T_g under ?120°C and the temperature of 50% weight loss was improved from 280 to 340°C. PE‐PDMS‐PE–modified TPU did not have the marked reduction on mechanical properties than pure polyether produced TPU. Tensile strength was maintained at 13 MPa and elongation was maintained at 300%. SEM and TEM were used to investigate the copolymers’ morphology performance and found that all PO PE‐PDMS‐PE had a pseudo‐three phase separation. WCA analysis confirmed that PE‐PDMS‐PE–modified TPU had significantly improved hydrophobic performance because the silicone structure linked into TPU copolymers. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42521.     

Crosslinking studies on poly(ethylene terephthalate‐co‐1,4‐phenylene bisacrylate)

Several compositionally different poly(ethylene terephthalate‐co‐1,4‐phenylene bisacrylate) (PETPBA) copolymers were melt spun into fibers. The resulting fibers were subjected to UV irradiation to induce crosslinking. Evidence of crosslinking was obtained from FTIR, solid‐state ¹³C‐NMR, thermal analysis, and solubility. Irradiation of the fiber results in an increased glass‐transition temperature, reduced thermal shrinkage, and enhanced modulus retention at elevated temperature. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 1698–1702, 2004     

Thermal,mechanical, and morphological characterization studies of poly(2,6‐dimethyl‐1,4‐phenylene oxide) blends with polystyrene and brominated polystyrene

The miscibility of the binary and ternary blends of poly(2,6‐dimethyl‐1,4‐phenylene oxide), brominated polystyrene, and polystyrene was investigated using a differential scanning calorimeter. The morphology of these blends was characterized by scanning electron microscopy. These studies revealed a close relation between the blend structure and its mechanical properties. The compatibilizing effect of poly(2,6‐dimethyl‐1,4‐phenylene oxide) on the miscibility of the polystyrene/brominated polystyrene blends was examined. It was found that poly(2,6‐dimethyl‐1,4‐phenylene oxide), which was miscible with polystyrene and partially miscible with brominated polystyrene, compatibilizes these two immiscible polymers if its contention exceeds 33 wt %. Upon the addition of poly(2,6‐dimethyl‐1,4‐phenylene oxide) to the immiscible blends of polystyrene/brominated polystyrene, we observed a change in the morphology of the mixtures. An improvement in the mechanical properties was noticed. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 75: 225–231, 2000