聚醚醚酮共混改性研究进展

综述了聚醚醚酮（PEEK）、聚醚酰亚胺（PEI）、聚四氟乙烯（PTFE）、热致液晶（TLCP）和聚醚砜（PES）等高性能工程塑料的共混改性研究进展,详细探讨了各种PEEK共混物的相容性、结晶行为、微观结构、热行为和力学性能等性能特征。PEEK与PEI在熔融和无定形状态下完全相容,常用于PEEK的结晶行为和微观结构的基础研究;与PTFE、TLCP、PES共混分别是提高PEEK的摩擦磨损性能、加工性能和热稳定性的有效手段。各种共混物的相容性好坏对其结晶行为和微观结构有重要影响,从而影响了共混物的力学性能。在此基础上,对PEEK共混改性领域进一步的研究方向和内容进行了讨论。     

Crystallization and melting behavior of poly(ether ether ketone)/poly(aryl ether sulfone) blends

The crystallization and melting behavior of poly(ether ether ketone) (PEEK) in blends with poly(aryl ether sulfone) (PES) prepared by melt mixing are investigated by differential scanning calorimetry (DSC) and wide‐angle X‐ray scattering (WAXS). The presence of PES is found to have a notable influence on the crystallization behavior of PEEK, especially when present in low concentrations in the PEEK/PES blends. The PEEK crystallization kinetics is retarded in the presence of PES from the melt and in the rubbery state. An analysis of the melt crystallization exotherm shows a slower rate of nucleation and a wider crystallite size distribution of PEEK in the presence of PES, except at low concentrations of PES, where, because of higher miscibility and the tendency of PES to form ordered structures under suitable conditions, a significantly opposite result is observed. The cold crystallization temperature of the blends at low PES concentration is higher then that of pure PEEK, whereas at a higher PES concentration little change is observed. In addition, the decrease in heat of cold crystallization and melting, which is more prevalent in PEEK‐rich compositions than in pure PEEK, shows the reduction in the degree of crystallinity because of the dilution effect of PES. Isothermal cold crystallization studies show that the cold crystallization from the amorphous glass occurs in two stages, corresponding to the mobilization of the PEEK‐rich and PES‐rich phases. The slower rate of crystallization of the PEEK‐rich phase, even in compositions where a pure PEEK phase is observed, indicates that the presence of the immobile PES‐rich phase has a constraining influence on the crystallization of the PEEK‐rich phase, possibly because of the distribution of individual PEEK chains across the two phases. The various crystallization parameters obtained from WAXS analysis show that the basic crystal structure of PEEK remains unaffected in the blend. Further, the slight melting point depression of PEEK at low concentrations of PES, apart from several other morphological reasons, may be due to some specific interactions between the component homopolymers. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 2906–2918, 2003     

Action of transfer film in improving friction and wear behaviors of iron‐ and copper‐filled poly(ether ether ketone) composites

The composites of poly(ether ether ketone) (PEEK) filled with micrometer‐sized Cu and Fe particles were prepared by compression molding. The friction and wear behaviors of the composites were examined on a pin‐on‐disc friction‐and‐wear tester by sliding PEEK‐based composites against tool steel at a sliding speed of 1.0 m s⁻¹ and a normal load of 19.6N. Optical microscopic analysis of the transfer film and of the worn pin surfaces and wear debris was performed to investigate the wear mechanisms of the composites. It was found that Cu and Fe used as filler considerably decreased the wear rate of PEEK. A thin, uniform, and tenacious transfer film was formed when Cu was used as the filler, and a nonuniform and thick transfer film was formed when Fe was used as the filler. The transfer film played a key role in increasing the wear resistance of the PEEK composites. Plastic deformation was dominant for wear of PEEK–Cu, while abrasion and adhesion were dominant for wear of PEEK–Fe. Because of the strong affinity between Fe as filler and its identical counterpart in the counterface tool steel surface, the adhesion between the PEEK–Fe composite surface and the counterface tool steel surface was thus severe. This contributed to the generation of a thicker transfer film for PEEK–Fe. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 76: 179–184, 2000     

Permeation resistance of poly(ether ether ketone) to hydrogen,nitrogen, and oxygen gases

We studied the gas permeation properties of poly(ether ether ketone) (PEEK) and compared it with two other polymers commonly used in the construction of semiconductor microenvironments, polycarbonate (PC), and poly(ether imide) (PEI). The PEEK specimens consisted of extruded films as well as compression‐ and injection‐molded specimens. The compression‐molded specimens were prepared to achieve the highest crystallinity. Injection‐molded disks, representing products, were milled to a prescribed thickness. Permeation, diffusion, and solubility coefficients were measured on these various PEEK specimens for hydrogen, nitrogen, and oxygen gases. It was found that PEEK generally has better permeation resistance than PC or PEI; showing up to five times lower permeation rates than PC or PEI, depending on grade, crystallinity, and gas. The superior permeation resistance of injection‐molded or extruded PEEK, when compared with similarly processed PC or PEI, comes from its crystallinity. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Thermal properties of melt‐blended poly(ether ether ketone) and poly(ether imide)

The thermal properties of blends of poly(ether ether ketone) (PEEK) and poly(ether imide) (PEI) prepared by screw extrusion were investigated by differential scanning calorimetry. From the thermal analysis of amorphous PEEK–PEI blends which were obtained by quenching in liquid nitrogen, a single glass transition temperature (T_g) and negative excess heat capacities of mixing were observed with the blend composition. These results indicate that there is a favorable interaction between the PEEK and PEI in the blends and that there is miscibility between the two components. From the Lu and Weiss equation and a modified equation from this work, the polymer–polymer interaction parameter (χ₁₂) of the amorphous PEEK–PEI blends was calculated and found to range from −0.058 to −0.196 for the extruded blends with the compositions. The χ₁₂ values calculated from this work appear to be lower than the χ₁₂ values calculated from the Lu and Weiss equation. The χ₁₂ values calculated from the T_g method both ways decreased with increase of the PEI weight fraction. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 72: 733–739, 1999     

Synthesis and properties of thio‐containing poly(ether ether ketone)s

A series of thio‐containing poly(ether ether ketone) (PEESK) polymers was synthesized by the introduction of thio groups from 4,4′ thiodiphenol (TDP) into the poly(ether ether ketone) (PEEK) structure via reaction between the phenol and aromatic fluoride groups. The effect of the thio groups on the properties of the PEESK materials was investigated. Differential scanning calorimetry (DSC) analysis and X‐ray diffraction (XRD) patterns show a depression in the crystallinity of the PEESKs with incorporation of the content of thio groups in the backbones. The crystalline structure was identified as an orthorhombic structure with lattice constants of a = 7.52 Å, b = 5.86 Å and c = 10.24 Å for all crystallizable PEESKs. The crystalline structures of the thio‐containing PEEK polymers were the same as that of the neat PEEK, which means the thio‐containing block in the whole thio‐containing PEEK molecule is almost excluded from the crystalline structure and the crystals are completely formed by ‘non‐thio’ blocks only. Due to the glass transition temperature (T_g) and melting temperature (T_m) depression with increase in the TDP content in the reaction system, the processability of the resultant thio‐containing PEEKs could be effectively improved. Copyright © 2004 Society of Chemical Industry     

Adhesion property of sulfonated poly(arylene ether sulfone)s

Sulfonated poly(arylene ether sulfone)s (S‐PESs) were synthesized from sulfonated 4,4′‐dichlorodiphenylsulfone (S‐DCDPS), 4,4′‐dichlorodiphenylsulfone (DCDPS), and 4,4′‐biphenol through variations in the molar ratio of S‐DCDPS to DCDPS from 10/90 to 40/60. The S‐PES sodium form was characterized with Fourier transform infrared, ¹H‐NMR, thermogravimetric analysis, differential scanning calorimetry, and dynamic mechanical analysis, and the intrinsic viscosity and solubility were also evaluated. The sodium form was then subjected to acidification by immersion in 1.5M HCl for 24 h at room temperature, which was followed by washing with deionized water. The S‐PES adhesive properties were measured with single laboratory shear samples with aluminum alloys, and the failure mode was investigated. The synthesized S‐PESs exhibited increased glass‐transition temperatures with increased S‐DCDPS/DCDPS ratios; their acid forms provided much lower glass‐transition temperatures than their sodium forms. In addition, the S‐PES sodium form exhibited a high intrinsic viscosity, which indicated a high molecular weight. The S‐PES acid form exhibited an adhesion strength similar to that of the sodium form, and the single‐lap‐shear strength increased with 10% S‐PES and then decreased with 20, 30, and 40% S‐PES. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 1211–1218, 2004     

Sulfonated poly(ether ether ketone)‐induced porous poly(ether sulfone) blend membranes for the separation of proteins and metal ions

Asymmetric ultrafiltration (UF) membranes were prepared by the blending of poly(ether sulfone) (PES) and sulfonated poly(ether ether ketone) (SPEEK) polymers with N,N′‐dimethylformamide solvent by the phase‐inversion method. SPEEK was selected as the hydrophilic polymer in a blend with different composition of PES and SPEEK. The solution‐cast PES/SPEEK blend membranes were homogeneous for all of the studied compositions from 100/0 to 60/40 wt % in a total of 17.5 wt % polymer and 82.5 wt % solvent. The presence of SPEEK beyond 40 wt % in the casting solution did not form membranes. The prepared membranes were characterized for their UF performances, such as pure water flux, water content, porosity, and membrane hydraulic resistance, and morphology and melting temperature. We estimated that the pure water flux of the PES/SPEEK blend membranes increased from 17.3 to 85.6 L m^?2 h^?1 when the concentration of SPEEK increased from 0 to 40 wt % in the casting solution. The membranes were also characterized their separation performance with proteins and metal‐ion solutions. The results indicate significant improvement in the performance characteristics of the blend membranes with the addition of SPEEK. In particular, the rejection of proteins and metal ions was marginally decreased, whereas the permeate flux was radically improved. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Hollow fiber microfiltration membranes from poly(ether ether ketone) (PEEK)

A procedure for obtaining high performance large internal diameter (ID; >1 mm) hollow fiber microfiltration membranes from poly(ether ether ketone) (PEEK) is presented. A simple mixture of isomers of diphenylphthalate is a good solvent for employing the thermal‐phase inversion process to obtain PEEK membranes. Obtaining large ID hollow fibers with substantial transmembrane flux requires sufficient melt strength during spinning to prevent excessive draw of the extruding fiber. The use of a second leachable polymer to the blend satisfies the conditions, and polysulphone (PS) is found to provide superior membranes relative to either poly(etherimide) (PEI) or poly(ether sulphone) (PES) as a second polymer. PEEK membranes obtained by this process yield better chemical resistance to a concentrated warm surfactant/oil solution. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 72: 175–181, 1999     

Spherulitic growth kinetics in miscible blends of poly(ether ether ketone) and poly(ether imide)

Growths of poly(ether ether ketone) (PEEK) spherulites from both pure melt and its miscible blends with poly(ether imide) (PEI) have been studied by polarized optical microscopy. The nucleation density of PEEK spherulites was depressed upon blending with PEI, which can be attributed to the reduction in degree of supercooling arising from equilibrium melting point depression. A modified Lauritzen-Hoffman (L-H) theory was adopted to analyze the growth kinetics. Regime III-II transition was observed with the transition temperature decreasing with increasing PEI composition. Assuming free rotations of the virtual bonds in PEEK molecule, the side surface free energy of 12.0 erg/cm² was calculated from the characteristic ratio. The fold surface free energy of 188 erg/cm² and work of chain folding of 12.3 kcal/mol were then obtained from the modified L-H analysis.     

Effect of high-performance polymers on crystallization and multiple melting behavior of poly(phenylene sulfide)

The crystallization and multiple melting behavior of poly(phenylene sulfide) (PPS) and its blends with amorphous thermoplastic bisphenol A polysulfone (PSF) and phenolphthalein poly(ether ketone) (PEK-C), crystalline thermoplastic poly(ether ether ketone) (PEEK), and thermosetting bismaleimide (BMI) resin were investigated by a differential scanning calorimeter (DSC). The addition of PSF and PEK-C was found to have no influence on the crystallization temperature (T_c) and heat of crystallization (ΔH_c) of PPS. A significant increase in the value of T_c and the intensity of the T_c peak of PPS was observed and the crystallization of PPS can be accelerated in the presence of the PEEK component. An increase in the T_c of PPS can also be accelerated in the BMI/PPS blend, but was no more significant than that in the PEEK/PPS blend. The T_c of PPS in the PEEK/PPS blends is dependent on the maximum temperature of the heating scans and can be divided into three temperature regions. The addition of a second component has no influence on the formation of a multiple melting peak. The double melting peaks can also be observed when PPS and its blends are crystallized dynamically from the molten state. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 69: 637–644, 1998     

Synthesis of multi‐block copolymer and its compatibilization to the blends of poly(ether ether ketone) with thermotropic liquid crystalline polymer

A multiblock copolymer (BCP) containing amorphous poly(aryl ether ketone) (PAEK) and thermotropic liquid crystalline polymer (TLCP) segments was synthesized. The chemical structure and properties of BCP were characterized by fourier‐transform infrared spectrometer (FTIR), differential scanning calorimeter (DSC), gel permeation chromatograms (GPC), thermogravimetry analysis, polar light microscope (PLM), and solubility test respectively. BCP can dissolve in chloroform because of soluble PAEK block bonded with TLCP block, which was insoluble. The peak of the original PAEK oligomer was no more present in the GPC traces of the block copolymer. These facts indicated that polymer synthesized should be copolymers of the two components rather than blends. A single T_g at 138.1°C and broad melting endotherm at 315.7°C can be observed. The liquid crystalline texture of BCP showed uniformity in the view after heat treated for 10 min above its T_m under PLM. Ternary blends of poly(ether ether ketone) (PEEK)/TLCP/BCP were prepared by extrusion and characterized by DSC. DSC results showed that the crystallization temperature of PEEK phase in the blends shifted higher with the addition of TLCP. Wide angle X‐ray diffraction investigations indicated that the crystalline structure of PEEK was not disturbed by blending or compatibilizing. Scanning electron microscope and mechanical tests confirmed the compatibilizing effect of BCP. Reduction in dispersed phase TLCP size was observed when 2 phr by weight of compatibilizer was added to the blend. Measurement of the tensile properties showed increased elongation as well as improved modulus and strength to some extent. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Miscibility and crystallization behavior of poly(ether ether ketone ketone)/poly(ether imide) blends

The miscibility and crystallization behavior of poly(ether ether ketone ketone) (PEEKK)/poly(ether imide) (PEI) blends prepared by melt‐mixing were investigated by differential scanning calorimetry. The blends showed a single glass transition temperature, which increased with increasing PEI content, indicating that PEEKK and PEI are completely miscible in the amorphous phase over the studied composition range (weight ratio: 90/10–60/40). The cold crystallization of PEEKK blended with PEI was retarded by the presence of PEI, as is apparent from the increase of the cold crystallization temperature and decrease of the normalized crystallinity for the samples anealed at 300°C with increasing PEI content. Although the depression of the apparent melting temperature of PEEKK blended with PEI was observed, there was no evidence of depression in the equilibrium melting temperature. The analysis of the isothermal crystallization at 313–321°C from the melt of PEEKK/PEI (100/0, 90/10, and 80/20) blends suggested that the retardation of crystallization of PEEKK is caused by the increase of the crystal surface free energy in addition to the decrease of the mobility by blending PEI with a high glass transition temperature. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 769–775, 2001     

Poly(ether ether ketone)/poly(aryl ether sulfone) blends: Relationships between morphology and mechanical properties

Mechanical properties such as the tensile modulus, yield (break) strength, and elongation to break (or yield) are measured for multiphase poly(ether ether ketone) (PEEK)/poly(aryl ether sulfone) (PES) blends. Specimens with three different levels of thermal histories (quenched, as‐molded, and annealed) are prepared in order to study their effects on the mechanical properties of PEEK/PES blends. Synergistic behavior is observed in the tensile modulus and tensile strength of the blends in almost the whole range of compositions. The ductility of quenched blends measured as the elongation to break (yield) shows an unexpected synergistic behavior in the blend containing 90 wt % PEEK, although a negative deviation from additive behavior is observed in the rest of the compositions. A ductile–brittle transition is observed between 50 and 75 wt % PEEK in the blend. The ductile–brittle transition in as‐molded blends shifts to 75–90 wt % PEEK. Annealed blends show predominantly brittle behavior in the whole composition range. The experimental data are further correlated with the theoretically predicted results based on various composite models. Although the prediction based on these equations fails to fit the experimental data in the whole composition range, the simplex equations that are normally used for blends showing synergistic behavior produced a reasonable fit to the experimental data. The mechanical properties obtained for different blend compositions are further correlated with their morphology as observed by scanning electron microscopy. Morphological observation shows a two‐phase morphology in PES‐rich blends, which is an interlocked morphology in which the disperse phase is not clearly visible in PEEK‐rich blends, and a cocontinuous type of morphology for a 50/50 composition. Considerable permanent deformation of both the disperse and matrix phase, especially in the case of quenched tensile specimens, demonstrates the remarkable adhesion present between the two phases. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 2887–2905, 2003     

Phase and crystallization behavior of solution-blended poly(ether ether ketone) and poly(ether imide)

Results on solution-blended poly(ether ether ketone) (PEEK) and poly(ether imide) (PEI) blends are reported. Dichloroacetic acid was used as the cosolvent for blending. PEEK and PEI are confirmed to be miscible in the melt. The glass transition, T_g, behavior obeys the simple Fox equation or the Gordon-Taylor equation with the adjustable coefficient k = 0.86. This agrees with prior data on melt-blended PEEK/PEI blends. The T_g width of the amorphous PEEK/PEI blends was found to be broader than that of the pure components. The maximum broadening is about 10°C. The specific volume of the amorphous PEEK/PEI blends shows a slight negative deviation from linearity, indicating favorable interaction between PEEK and PEI. The spherulitic growth and resultant blend morphology at 270°C were studied by a cross-polarized optical microscope. The radial growth rate of PEEK spherulites formed from the miscible melt at 270°C decreases from 3.04 μm/min for PEEK/PEI 90/10 blend to 0.77 μm/min for PEEK/PEI 70/30 blend. The decrease in crystalization rate of PEEK from PEEK/PEI blends is attributable to the increase in blend T_g. A linear growth was observed for PEEK spherulites formed from miscible melt at 270°C in the early growth stage. The spherulitic growth deviated from linearity in the late stage of growth. PEEK spherulites formed from the miscible PEEK/PEI melt at 270°C are essentially volume-filling. The branches of the spherulites become more clear for PEEK spherulites formed from the blend than that formed from pure PEEK melt.     

Phase separation behavior of poly(ether imide)/N,N‐dimethyl acetamide/nonsolvent systems

The phase separation behavior of a poly(ether imide) (PEI)/N,N‐dimethyl acetamide (DMAc)/nonsolvent system was investigated. Three kinds of nonsolvents were used in the study: H₂O, ethanol, and acetic acid (AA). It was found that the three systems (PEI/DMAc/H₂O, PEI/DMAc/ethanol, and PEI/DMAc/AA) agree with the linearized cloud point (LCP) relation. The binodal lines of the three systems were calculated according to the LCP relation. The binodal line of the PEI/DMAc/(H₂O + DMAc) system was also calculated according to the LCP relation of the PEI/DMAc/H₂O system. The phase separation of the PEI/DMAc/(H₂O + AA) system was studied, and the results agree with the LCP relation. These results can offer useful information for the establishment of dope and coagulation media using for the fabrication of a PEI membrane. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 875–881, 2003     

Rheological properties in blends of poly(aryl ether ether ketone) and liquid crystalline poly(aryl ether ketone)

Rheological properties of the blends of poly(aryl ether ether ketone) (PEEK) with liquid crystalline poly(aryl ether ketone) containing substituted 3‐trifluoromethylbenzene side group (F‐PAEK), prepared by solution precipitation, have been investigated by rheometer. Dynamic rheological behaviors of the blends under the oscillatory shear mode are strongly dependent on blend composition. For PEEK‐rich blends, the systems show flow curves similar to those of the pure PEEK, i.e., dynamic storage modulus G′ is larger than dynamic loss modulus G″, showing the feature of elastic fluid. For F‐PAEK‐rich systems, the rheological behavior of the blends has a resemblance to pure F‐PAEK, i.e., G″ is greater than G′, showing the characteristic of viscous fluid. When the PEEK content is in the range of 50–70%, the blends exhibit an unusual rheological behavior, which is the result of phase inversion between the two components. Moreover, as a whole, the complex viscosity values of the blends are between those of two pure polymers and decrease with increasing F‐PAEK content. However, at 50% weight fraction of PEEK, the viscosity‐composition curves exhibit a local maximum, which may be mainly attributed to the phase separation of two components at such a composition. The changes of G′ and G″ with composition show a trend similar to that of complex viscosity. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 4040–4044, 2006     

Different parameters controlling the initial solubility of two thermoplastics in epoxy reactive solvents

The influence of different factors on the miscibility of diglycidyl ether of bisphenol A (DGEBA)/thermoplastic blends was studied. DGEBA/poly(ether imide) (PEI) blends exhibited upper critical solution temperature behavior. The addition of a trifunctional epoxy [triglycidyl para‐amino phenol (TGpAP)] increased the miscibility window. The addition of diamines as hardeners could also increase [4,4′‐methylene‐bis(3‐chloro‐2,6‐diethylaniline) (MCDEA)] or decrease (4,4′‐diaminodiphenylsulfone) the miscibility window. DGEBA/poly(ether sulfone) (PES) blends showed lower critical solution temperature behavior. The addition of TGpAP had an effect similar to that for PEI blends, but the presence of MCDEA as a hardener decreased the miscibility of epoxy/PES blends. The modeling of the cloud‐point curves was performed with the Flory–Huggins equation (Flory, P. J. Principles of Polymer Chemistry; Cornell University Press: Ithaca, NY, 1953; p 672) according to the procedure developed by K. Kamide, S. Matsuada, and H. Shirataki (Eur Polym J 1990, 26, 379), with the interaction parameter used as the fitting parameter. A phenomenological model that takes into account the molar mass of DGEBA and the amount of TGpAP is proposed and is found to predict the cloud‐point temperature of any TGpAP/DGEBA/PEI blend. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 1385–1396, 2002     

Poly(acrylonitrile‐butadiene‐styrene)/Poly(ether ether ketone) Blends: an Attempt Towards a Polymer Reinforced Polymer Composite

Summary: Blends of poly(acrylonitrile‐butadiene‐styrene) (ABS) and poly(ether ether ketone) (PEEK), in which PEEK has been used as a reinforcing medium for the ABS matrix in ratios up to 20 wt.‐% of the blend, were prepared by melt mixing using a laboratory mixer. All the blend compositions were processed at the ABS processing temperature so that the PEEK was dispersed in the ABS matrix without actually melting. Differential scanning calorimetry (DSC) and dynamic mechanical analysis (DMA) studies revealed that the glass transition temperature (T_g) of the ABS phase in the blend did not show any appreciable change with composition. The dynamic storage modulus measured by DMA was found to be higher for the blend as compared to pure ABS due to reinforcement of the matrix by PEEK. The tensile strength and modulus behavior of these blends were found to follow the curves predicted using models proposed for composite systems having perfect adhesion, which shows the presence of some physical interaction between the blend components. The good tensile properties of the blend have been correlated with the observed morphology. The disperse phase in the blend has been found to be present in extremely small (sub‐micron) dimensions, which not only provides more surface area for possible interactions between the blend components but also result in efficient stress transfer between the matrix and the dispersed phase during the tensile tests. The thermal stability of the blends was investigated using thermogravimetric analysis (TGA). TGA further revealed that the constituents degraded at their respective decomposition temperatures.

SEM micrograph of tensile fractured surface of an ABS/PEEK 90/10 blend.     

Crystallization and melting behavior of poly(p‐phenylene sulfide) in blends with poly(ether sulfone)

Crystallization and melting behaviors of poly(p‐phenylene sulfide) (PPS) in blends with poly(ether sulfone) (PES) prepared by melt‐mixing were investigated by differential scanning calorimetry (DSC). The blends showed two glass transition temperatures corresponding to PPS‐ and PES‐rich phases, which increased with increasing PES content, indicating that PPS and PES have some compatibility. The cold crystallization temperature of the blended PPS was a little higher than that of pure PPS. Also, the heats of crystallization and melting of the blended PPS decreased with increasing PES content, indicating that the degree of crystallinity decreased with an increase of PES content. The isothermal crystallization studies revealed that the crystallization of PPS is accelerated by blending PPS with 10 wt % PES and further addition results in the retardation. The Avrami exponent n was about 4 independent on blend composition. The activation energy of crystallization increased by blending with PES. The equilibrium melting point decreased linearly with increasing PES content. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 1686–1692, 1999