Ethylene vinyl acetate/layered silicate nanocomposites prepared by a surfactant-free method: Enhanced flame retardant and mechanical properties

Exfoliated EVA/layered silicate nanocomposites were prepared by a masterbatch process using polymer-modified layered silicate instead of small molecule surfactant-modified clays. The nanocomposites exhibited improved mechanical properties and flame retardancy. Microscale flammability test showed that the heat release capacity (HRC) and total heat release (THR) were reduced by 21-24% and 16%, respectively. Radiant gasification studies revealed that the exfoliated EVA nanocomposites exhibited better improvements in flame retardant properties of EVA than did the corresponding intercalated nanocomposites. The peak mass loss rate of the exfoliated EVA nanocomposite containing about 5 wt% clay was reduced by 80% and the mass loss rate plot was spread over a much longer period of time. The mechanical and flammability tests revealed that the observed improvements in all the desirable properties were due to the presence of both the incorporated polymeric surfactant and the nanoclay.     

硅氧烷处理纳米层状硅酸盐对膨胀阻燃聚乳酸性能的影响

采用4种经过不同表面处理剂改性的有机层状硅酸盐（Clay）与膨胀型阻燃剂复配阻燃聚乳酸（PLA）。通过熔融共混的方法制备阻燃PLA纳米复合材料,并通过极限氧指数、垂直燃烧、锥形量热测试和热失重分析对材料阻燃性能和热稳定性进行了研究,通过扫描电子显微镜对残炭形貌进行了分析。结果表明,加入经硅氧烷表面处理的Clay的PLA具有最好的热稳定性和阻燃性能;与不加Clay的阻燃PLA复合材料相比,极限氧指数从30.6 %提高至34.2 %,并且通过垂直燃烧UL 94 V-0级别,热释放速率峰值从283 kW/m2下降至199 kW/m2,下降幅度为30 %;残炭形貌分析结果显示,加入硅氧烷表面处理之后的Clay能够使残炭更加完整致密,从而提高了材料的阻燃性能。     

Contribution of nanoclays to the performance of traditional flame retardants in ABS

The purpose of this study was to investigate contribution of nanoclays to the flame retardancy performance of a traditional brominated flame retardant compound with various combinations of antimony trioxide and zinc borate. The matrix polymer acrylonitrile butadiene styrene (ABS) was compounded by melt mixing in a laboratory size twin‐screw extruder. X‐ray diffraction analysis and transmission electron microscopy revealed that nanoclay silicate layers were mainly intercalated with certain level of exfoliation in ABS matrix. Flammability analysis investigated by mass loss calorimeter, limiting oxygen index, and UL‐94 tests indicated that use of nanoclays improved all flame retardancy parameters significantly. For instance, the increase in the limiting oxygen index was up to 32% O₂, while the suppression in peak heat release rate value was as much as 82%, of course in each specimen the highest rating of V‐0 in UL‐94 test was obtained. Thermogravimetric and other residue analyses pointed out that these contributions were especially due to the condensed phase flame retardancy mechanism of nanoclay which contributes stronger and carbonaceous char formation acting as a barrier to heat and flammable gases and retarding volatilization via tortuous pathway. POLYM. COMPOS., 2012. © 2012 Society of Plastics Engineers     

Synergistic effects of exfoliated LDH with some halogen‐free flame retardants in LDPE/EVA/HFMH/LDH nanocomposites

The synergistic effects of exfoliated layered double hydroxides (LDH) with some halogen‐free flame retardant (HFFR) additives, such as hyperfine magnesium hydroxide (HFMH), microencapsulated red phosphorus (MRP), and expandable graphite (EG), in the low‐density polyethylene/ethylene vinyl acetate copolymer/LDH (LDPE/EVA/LDH) nanocomposites have been studied by X‐ray diffraction (XRD), transmission electron microscopy (TEM), scanning electron microscopy (SEM), thermal analysis (TGA and DTG), mechanical properties, limiting oxygen index (LOI), and UL‐94 tests. The XRD results show that EVA as an excellent compatilizer can promote the exfoliation of LDH and homogeneous dispersion of HFMH in the LDPE/EVA/HFMH/LDH nanocomposites prepared by melt‐intercalation method. The TEM images demonstrate that the exfoliated LDH layers can act as synergistic compatilizer and dispersant to make the HFMH particles dispersed homogeneously in the LDPE matrix. The results from the mechanical, LOI, and UL‐94 tests show that the exfoliated LDH layers can also act as the nano‐enhanced and flame retardant synergistic agents and thus increase the tensile strength, LOI values, and UL‐94 rating of the nanocomposites. The morphological structures of charred residues observed by SEM give the positive evidence that the compact charred layers formed from the LDPE/EVA/HFMH/LDH nanocomposites with the exfoliated LDH layers play an important role in the enhancement of flame retardant and mechanical properties. The TGA and DTG data show that the exfoliated LDH layers as excellent flame retardant synergist of MRP or EG can apparently increase the thermal degradation temperature and the charred residues after burning. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Combustion characteristics and synergistic effects of red phosphorus masterbatch with expandable graphite in the flame retardant HDPE/EVA composites

In this work, the flammability behaviors and synergistic effects of red phosphorus masterbatch (RPM) with expandable graphite (EG) in flame‐retardant high‐density polyethylene/ethylene vinyl‐acetate copolymer (HDPE/EVA) composites have been investigated by limiting oxygen index (LOI), UL‐94 test, cone calorimeter test (CCT), thermogravimetric analysis (TGA), Fourier‐transform infrared (FTIR) and scanning electron microscopy (SEM). The data obtained from LOI, UL‐94 test and CCT showed that suitable amount of RPM had synergistic effects with EG in the HDPE/EVA/EG/RPM composites. The addition of RPM greatly increased the LOI values by 3.4%, obtained UL‐94 V‐0 rating, decreased the heat release rates and total heat release, and prolongated the ignition time when 6.7 phr RPM substituted for EG in the HDPE/EVA/EG/RPM composites. The data from TGA and FTIR spectra also indicated the synergistic effects of RPM with EG considerably enhanced the thermal degradation temperatures. The morphological observations after UL‐94, CCT, and SEM images presented positive evidences that the synergistic effects took place for RPM with EG, and the flame‐retardant mechanism has been changed in flame‐retardant HDPE/EVA/EG/RPM composites. The formation of stable and compact charred residues promoted by RPM acted as effective heat barriers and thermal insulations, which improved the flame‐retardant performances and prevented the underlying polymer materials from burning. POLYM. ENG. SCI., 55:2884–2892, 2015. © 2015 Society of Plastics Engineers     

磷氮复配无卤阻燃聚苯醚合金的研究

采用固体阻燃剂间苯二酚双[二(2,6-二甲苯基)磷酸酯](RXP)及其与三聚氰胺氰脲酸盐(MCA)的复配阻燃剂,制备了无卤阻燃聚苯醚/高抗冲聚苯乙烯/苯乙烯-丁二烯-苯乙烯热塑性弹性体(PPE/PS-HI/SBS)合金,通过氧指数、水平垂直燃烧、扫描电子显微镜、力学性能等测试分析方法,考察了PPE/PS-HL/SBS合...     

Synthesis and characterization of chlorine‐containing flame‐retardant polyurethane nanocomposites via in situ polymerization

We have developed flame‐retardant polyurethanes (FRPUs) and polyurethane (PU) nanocomposites via in situ polymerization. Three series of thermoplastic elastomeric PUs were synthesized to investigate the effect of incorporating 3‐chloro‐1,2‐propanediol (CPD) and nanoclay on mechanical, thermal properties, and also resistance to burning. PU soft segments were based on poly(propylene glycol). Hard segments were based on either CPD or 1,4‐buthane diol (BDO) in combination with methyl phenyl di‐isocyanate named PU or FRPU, respectively. In the third series, CPD was used as chain extender also nanoclay (1% wt) and incorporated and named as flame‐retardant polyurethane nanocomposites (FRPUN). Mechanical properties and LOI of PUs and nanocomposites have been evaluated. Results showed that increasing the hard segment (chlorine content) leads to the increase in flame retardancy and burning time. Addition of nanoclay to CPD‐containing PUs leads to obtain self‐extinguish PUs using lower CPD contents, higher Young's modulus, and strength without any noticeable decrease in elongation at break. Investigation of the TGA results showed that copresence of nanoclay and chlorine structure in the PU backbone can change thermal degradation pattern and improve nanocomposite thermal stability. X‐ray diffraction and transmission electron microscopy studies confirmed that exfoliation and intercalation have been well done. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

阻燃环氧树脂/有机蒙脱土纳米复合材料制备及阻燃性能

研究制备了环氧树脂(EP)/有机蒙脱土(OMMT)、N,N-二(2-羟乙基)氨甲基膦酸二乙酯(BHAPE)阻燃剂阻燃的EP和EP/OMMT等复合材料。XRD证明分散在复合材料中的OMMT为剥离型的,且BHAPE的加入不影响材料中OMMT剥离后的层间距。研究证明,单独使用BHAPE很难使EP通过UL 94 V-0阻燃级,仅添加OMMT的EP固化物,其氧指数和UL94阻燃性能几乎与纯EP固化物的一样。但是同时添加BHAPE和OMMT的EP固化物,当BHAPE和OMMT的添加量分别为25%和5%时,不仅BHAPE/EP/OMMT复合物的CONE阻燃参数都明显降低,而且能通过UL94V-0级。可能是BHAPE和OMMT在凝聚相同时发挥作用,即BHAPE和OMMT协同阻燃作用提高了复合材料的综合阻燃性能。     

Synthesis of flame retardant polyester‐urethanes and their applications in nanoclay composites and coatings

This paper describes the synthesis of phosphorus‐containing polyester‐urethanes and their applications in nanoclay composites and coatings. Polyester was prepared by the reaction of bis(bisphenol‐A) monophenyl phosphonate, maleic anhydride and phthalic anhydride. The polyester was reacted with various diols such as ethylene glycol, diethylene glycol and propylene glycol to obtain polyester polyols. Synthesized polyester polyols were characterized by chemical analysis and instrumental analysis and was used further to react with different isocyanates to develop polyester‐urethanes. The synthesized polyester‐urethanes were blended with organo‐modified montmorillonite nanoclay (1 wt%, 3 wt% and 5 wt%) and were cast in a mold and coated on mild steel panels. The thermal stability of neat polyester‐urethane and the nanoclay composites was determined by thermogravimetric analysis. The flame retardant properties of cast films and their composites were determined by the limiting oxygen index and UL‐94 test methods. The physical and mechanical properties of coatings such as pot life, drying properties, scratch hardness, pencil hardness, impact resistance, adhesion and flexibility were investigated. The chemical resistance properties of the coatings were also determined in different reagents. The data reveal that the polyester‐urethane nanoclay composites with 3 wt% clay hold promise for use in effective flame retardant coatings. © 2013 Society of Chemical Industry     

Flame Retardancy and Thermal Performance of Polypropylene Treated With the Intumescent Flame Retardant,Piperazine Spirocyclic Phosphoramidate

Piperazine spirocyclic phosphoramidate (PSP), a novel halogen‐free intumescent flame retardant, was synthesized and used to improve the flame retardancy and dripping resistance of polypropylene (PP) combined with ammonium polyphosphate (APP) and a triazine polymer charring‐foaming agent (CFA). The optimum flame‐retardant formulation was PSP:APP:CFA = 3:6:2 (weight ratio). The flammability and thermal behavior of the (intumescent flame‐retardant)‐PP (IFR‐PP) were investigated via limiting oxygen index (LOI), vertical burning tests (UL‐94), thermogravimetric analysis, and cone calorimetry (CONE). The results indicated that the IFR‐PP had both excellent flame retardancy and anti‐dripping ability. The optimum flame‐retardant formulation gave an LOI value of 39.8 and a UL‐94 V‐0 rating to PP. Moreover, both the heat release rate and the total heat release of the IFR‐PP with the optimum formulation decreased significantly relative to those of pure PP, according to the cone calorimeter analyses. The residues of IFR‐PP obtained after CONE tests were observed by scanning electron microscopy, and it was found that the char yield was directly related to the flame retardancy and anti‐dripping behavior of the treated PP. J. VINYL ADDIT. TECHNOL., 20:10–15, 2014. © 2014 Society of Plastics Engineers     

Flame‐retarding mechanism of organically modified montmorillonite and phosphorous‐Nitrogen flame retardants for the preparation of a halogen‐free,flame‐retarding thermoplastic poly(ester ether) elastomer

In this study, thermoplastic poly(ester ether) elastomer (TPEE) nanocomposites with phosphorus–nitrogen (P–N) flame retardants and montmorillonite (MMT) were prepared by melt blending. The fire resistance of the nanocomposites was analyzed by limiting oxygen index (LOI) and vertical burning (UL 94) tests. The results show that the addition of the P–N flame retardants increased the LOI of the material from 17.3 to 27%. However, TPEE containing P–N flame retardants only obtained a UL 94 V‐2 ranking; this resulted in a flame dripping phenomenon. On the other hand, TPEE containing the P–N flame retardant and organically modified montmorillonite (o‐MMT) achieved better thermal stability and good flame retardancy; this was ascribed to its partially intercalated structure. The synergistic effect and synergism were investigated by Fourier transform infrared spectroscopy and thermogravimetry. The introduction of o‐MMT decreased the inhibition action of the P–N flame retardant and increased the amount of residues. The catalytic decomposition effect of MMT and the barrier effect of the layer silicates are discussed in this article. The residues after heating in the muffle furnace were analyzed by scanning electron microscopy, energy‐dispersive X‐ray spectroscopy and laser Raman spectroscopy. It was shown that the intercalated layer silicate structure facilitated the crosslinking interaction and promoted the formation of additional carbonaceous char residues in the formation of the compact, dense, folded‐structure surface char. The combination of the P–N flame retardant and o‐MMT in TPEE resulted in a better thermal stability and fire resistance because of the synergistic effect of the mixture. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 41094.     

Influences of specimen size and heating mode on the ignitability of polymeric materials in typical small‐scale fire test conditions

Small‐scale fire tests including the Underwriters Laboratories 94 (UL94) vertical burning test and the cone calorimeter test are widely used. In this paper, the ignition times of materials heated by the conical heater of a cone calorimeter and the UL94 flame were measured. It was found that for polymer bars heated by the UL94 flame, the ignition time is relatively short and increases with the specimen thickness. But the contribution of the specimen thickness to the delay of the ignition time is limited. The intrinsic properties of materials play a more important role in the ignition time than the specimen thickness. In addition, respectively corresponding to one‐dimensional, two‐dimensional, and three‐dimensional heat transfer, three heating modes of the UL94 flame were presented and compared with the conical heater. It was found that whether the heat source is the conical heater or the UL94 flame, the ignition time depends on the heat flux and the multidimensional heat transfer. The ignition time decreases with the increasing heat flux, and the magnitude order of the ignition time might drop when the heating mode changes from one‐dimensional to multidimensional heat transfer. Copyright © 2011 John Wiley & Sons, Ltd.     

EG与IFR复合阻燃EVA的动态燃烧性能和协同效应

将可膨胀石墨(EG)与P-N膨胀阻燃剂(IFR)复合阻燃EVA树脂,通过氧指数(OI)、垂直燃烧测试(UL94)、锥形量热仪(CONE)研究了EG与IFR复合阻燃EVA的协同效应。结果表明:阻燃剂总添加量为30 phr,随着其中EG含量的增加,OI呈先增加后下降趋势,确定EG:IFR=1:1为最佳配比,OI达到36.6%,UL94为V-0级;EG与IFR复合阻燃EVA,热释放速率曲线呈现"前单峰型",为凝聚相阻燃机理;燃烧后形成的炭层结构较致密,表现出一定的协同作用。     

Synergistic effect of aluminum hydroxide and nanoclay on flame retardancy and mechanical properties of EPDM composites

The composites based on ethylene–propylene–diene monomer rubber (EPDM) with aluminum hydroxide (ATH), nanoclay, vulcanizing agent, and curing accelerator were prepared by conventional mill compounding method. The thermal stability and the flame retardant properties were evaluated by thermogravimetric analysis (TGA), limiting oxygen index (LOI), UL‐94 test, cone calorimeter, and smoke density chamber tests. The results indicated that the substitution of the nanoclay in the EPDM/ATH composites increased the 50% weight loss temperature and the LOI value, and reduced the peak heat release rate (pk‐HRR), the extinction coefficient (Ext Coef), the maximal smoke density (Dm), and the whole smoke at the first 4 min (VOF4) of the test specimens. The synergistic flame retardancy of the nanoclay with ATH in EPDM matrix could imply that the formation of a reinforced char/nanoclay layer during combustion prevents the diffusion of the oxygen and the decomposed organic volatiles in the flame. The mechanical properties of the composites have been increased by replacing more of the nanoclays into the EPDM/ATH blends. The best loading of the nanoclay in EPDM/ATH composites is 3 wt %, which keeps LOI in the enough value, the V‐0 rating in the UL‐94 test, and the improved mechanical properties with better dispersion and exfoliation of the nanoclays shown by transmission electron microscopy (TEM) micrographs. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 2042–2048, 2013     

Preparation and investigation of flame‐retardant epoxy resin modified with a novel halogen‐free flame retardant containing phosphaphenanthrene,triazine‐trione,and organoboron units

In this article, a novel flame retardant (coded as BNP) was successfully synthesized through the addition reaction between triglycidyl isocyanurate, 9,10‐dihydro‐9‐oxa‐10‐phosphaphenanthrene‐10‐oxide and phenylboronic acid. BNP was blended with diglycidyl ether of bisphenol‐A to prepare flame‐retardant epoxy resin (EP). Thermal properties, flame retardancy, and combustion behavior of the cured EP were studied by thermogravimetric analysis, limited oxygen index (LOI) measurement, UL94 vertical burning test, and cone calorimeter test. The results indicated that the flame retardancy and smoke suppressing properties of EP/BNP thermosets were significantly enhanced. The LOI value of EP/BNP‐3 thermoset was increased to 32.5% and the sample achieved UL94 V‐0 rating. Compared with the neat EP sample, the peak of heat release rate, average of heat release rate, total heat release, and total smoke production of EP/BNP thermosets were decreased by 58.2%–66.9%, 27.1%–37.9%, 25.8%–41.8%, and 21.3%–41.7%, respectively. The char yields of EP/BNP thermosets were increased by 46.8%–88.4%. The BNP decomposed to produce free radicals with quenching effect and enhanced the charring ability of EP matrix. The multifunctional groups of BNP with flame retardant effects in both gaseous and condensed phases were responsible for the excellent flame retardancy of the EP/BNP thermosets. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45291.     

Morphology and rheological behavior of polylactic acid/clay nanocomposites

The investigated rheological properties of polylactic acid (PLA)/clay nanocomposite are important to understand the effect of organically modified layered silicates (OMLS) (clay) on processing as well as the change in viscoelastic properties due to polymer filler interaction. The time sweep result revealed that the thermal stability improved with addition of nanoclay due to the formation of percolating network structure. It was also supported by multi wave ramp test. The frequency sweep analysis showed that the dynamic moduli increased with addition of nanoclay. Viscoelastic spectra (DMTA) showed an increase of the storage and loss moduli with the increase in the clay content. Wide angle X‐ray diffraction (WAXD) and transmission electron microscopy (TEM) were used to determine the degree of intercalation, or exfoliation and nanostructure level of clay dispersion on PLA nanocomposites. XRD data demonstrated complete exfoliation at lower nanoclay content. On increasing the nanoclay content, exfoliated and partially intercalated structures were obtained. POLYM. ENG. SCI., 2012. © 2011 Society of Plastics Engineers     

Morphologies and properties of nanocomposite films based on a biodegradable poly(ester)urethane elastomer

Biodegradable poly(ester)urethane (PU) elastomer‐based nanocomposite films incorporated with organically modified nanoclay were prepared with melt‐extrusion compounding followed by a casting film process. These films were intended for application as biodegradable food packaging films, with their enhanced gas barrier, mechanical, and thermal properties and good flexibility. From both X‐ray diffraction measurements and transmission electron microscopy observations, the coexistence of intercalated tactoids and exfoliated silicate layers in the compounded PU/clay nanocomposite films was confirmed. In addition, the morphology exhibited a clay dispersion state in the matrix and was influenced by the incorporated nanoclay content. The effects of the nanoclay loading level on the thermal, mechanical, and barrier properties of the compounded nanocomposites were also investigated. As a result, it was revealed that the addition of nanoclay up to a certain level resulted in a remarkable improvement in the thermal properties in terms of thermal stability and the degree of thermal shrinkage; mechanical properties, including dynamic storage modulus and tensile modulus; and oxygen/water‐vapor barrier properties of the nanocomposite films. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Preparation and characterization of new flame retardant polyurethane composite and nanocomposite

In this work, a new flame retardant additive [2‐phenyl‐1,3,2 oxazaphospholidine 2‐oxide (POPO)] containing phosphorus and nitrogen is synthesized using phenyl phosphonic dichloride, ethanol amine, and copper (II) chloride, as catalyst. POPO is characterized by ¹H‐NMR, ¹³C‐NMR, and ³¹P‐NMR and used as additive in polyurethane composites. Moreover, two commercial flame retardant additives [tricalcium diphosphate and hexabromocyclododecane (HBCD)] as well as nanoclay are used to compare flame retardancy of the synthesized additive. Limited oxygen index (LOI) and time burning (flammability test) of polyurethane composites and nanocomposites are evaluated. The results of the LOI test demonstrate that POPO is an excellent flame retardant additive and can be used to improve flame retardancy of polyurethane composites. In addition, increasing the additive content leads to an improvement of the flame retardancy of the samples. The LOI results show, however, that POPO is a good flame retardant, but the high synthesis cost of this flame retardant is a major disadvantage. Thermogravimetric analysis results show that using POPO in polyurethane matrices leads to low thermal stability and high char residue. Moreover, the nanocomposite has better thermal stability than the other samples. Scanning electron microscope micrographs have been used to evaluate the char residue of the samples. These micrographs indicate that POPO is an intumescent flame retardant and HBCD follows a nonintumescent mechanism. Exfoliated/intercalated structures have been shown for nanocomposites by transmission electron microscope. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

A phosphorus‐containing inorganic compound as an effective flame retardant for glass‐fiber‐reinforced polyamide 6

A novel inorganic compound, aluminum hypophosphite (AP), was synthesized successfully and applied as a flame retardant to glass‐fiber‐reinforced polyamide 6 (GF–PA6). The thermal stability and burning behaviors of the GF–PA6 samples containing AP (flame‐retardant GF–PA6) were investigated by thermogravimetric analysis, vertical burning testing (with a UL‐94 instrument), limiting oxygen index (LOI) testing, and cone calorimeter testing (CCT). The thermogravimetric data indicated that the addition of AP decreased the onset decomposition temperatures, the maximum mass loss rate (MLR), and the maximum‐rate decomposition temperature of GF–PA6 and increased the residue chars of the samples. Compared with the neat GF–PA6, the AP‐containing GF–PA6 samples had obviously improved flame retardancy: the LOI value increased from 22.5 to 30.1, and the UL‐94 rating went from no rating to V‐0 (1.6 mm) when the AP content increased from 0 to 25 wt % in GF–PA6. The results of CCT reveal that the heat release rate, total heat release, and MLR of the AP‐containing GF–PA6 samples were lower than those of GF–PA6. Furthermore, the higher additive amount of AP affected the mechanical properties of GF–PA6, but they remained acceptable. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Component ratio effects of hyperbranched triazine compound and ammonium polyphosphate in flame‐retardant polypropylene composites

A hyperbranched derivative of triazine group (EA) was synthesized by elimination reaction between ethylenediamine and cyanuric chloride. The different‐mass‐ratio EA and ammonium polyphosphate (APP) were mixed and blended with polypropylene (PP) in a constant amount (25%) to prepare a series of EA/APP/PP composites. The component ratio effect of EA/APP on the flame‐retardant property of the EA/APP/PP composites was investigated using the limiting oxygen index (LOI), vertical burning (UL‐94), and cone calorimetry tests. Results indicated that the EA/APP/PP (7.50/17.50/75.00) composite with the appropriate EA/APP mass ratio had the highest LOI, UL94 V‐0 rating, lowest heat release rate, and highest residue yield. These results implied that the appropriate EA/APP mass ratio formed a better intumescent flame‐retardant system and adequately exerted their synergistic effects. Furthermore, average effective combustion heat values revealed that EA/APP flame retardant possessed the gaseous‐phase flame‐retardant effect on PP. Residues of the EA/APP/PP composites were also investigated by scanning electron microscopy, Fourier‐transform infrared, and X‐ray photoelectron spectroscopy. Results demonstrated that the appropriate EA/APP mass ratio can fully interact and lock more chemical constituents containing carbon and nitrogen in the residue, thereby resulting in the formation of a dense, compact, and intumescent char layer. This char layer exerted a condensed‐phase flame‐retardant effect on EA/APP/PP composites. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 41006.