首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 15 毫秒
1.
针对传统非奇异终端滑模控制方法不适用于3阶系统的问题,提出一类具有不确定和外干扰的3阶非线性系统的新型非奇异终端滑模控制方法.该方案首先结合backstepping控制中的动态面方法和传统2阶非奇异终端滑模控制构造非奇异3阶终端滑模面,首次提出采用高阶滑模微分器估计值代替控制器中的负指数项.采用非线性干扰观测器任意精度地估计不确定和干扰,设计控制器中的补偿项.采用终端吸引子函数做趋近律避免抖振的同时能保证有限时间趋近滑模面.基于有限时间稳定李雅普诺夫定理证明了被控状态将在有限时间内收敛到任意小的闭球内.所提出方案快于传统的递阶线性滑模控制和其他非奇异终端滑模控制.仿真中与其他滑模控制方案对比,总误差减小18%以上,超调及收敛时间也显著下降.  相似文献   

2.
自适应广义滑模观测器之状态估计和故障重构   总被引:1,自引:0,他引:1  
针对一类同时具有执行机构故障和输出扰动的不确定性系统,提出了一种自适应广义滑模观测器,实现系统状态的估计和执行机构故障的重构.首先,进行系统变换及状态增广构成一类奇异系统,使得执行机构故障和输出扰动解耦,且输出扰动成为增广系统的状态之一;随后,受未知输入观测器和滑模观测器的启发,设计了一种广义滑模观测器,放宽了传统方法对输出维数的严格约束,并通过融入自适应技术放宽了对故障和不确定性上界已知的要求;最后,利用等效误差注入的思想实现故障重构.针对可重复使用运载器再入段进行的仿真实例,验证了所提方法的有效性.  相似文献   

3.
This paper focuses on the design of nonlinear robust controller and disturbance observer for the longitudinal dynamics of a hypersonic vehicle (HSV) in the presence of parameter uncertainties and external disturbances. First, by combining terminal sliding mode control (TSMC) and second-order sliding mode control (SOSMC) approach, the secondorder terminal sliding control (2TSMC) is proposed for the velocity and altitude tracking control of the HSV. The 2TSMC possesses the merits of both TSMC and SOSMC, which can provide fast convergence, continuous control law and hightracking precision. Then, in order to increase the robustness of the control system and improve the control performance, the sliding mode disturbance observer (SMDO) is presented. The closed-loop stability is analyzed using the Lyapunov technique. Finally, simulation results illustrate the effectiveness of the proposed method, as well as the improved overall performance over the conventional sliding mode control (SMC).  相似文献   

4.
Asymptotic output‐feedback tracking in a class of causal nonminimum phase uncertain nonlinear systems is addressed via sliding mode techniques. Sliding mode control is proposed for robust stabilization of the output tracking error in the presence of a bounded disturbance. The output reference profile and the unknown input/disturbance are supposed to be described by unknown linear exogenous systems of a given order. Local asymptotic stability of the output tracking error dynamics along with the boundedness of the internal states are proven. The unstable internal states are estimated asymptotically via the proposed multistage observer that is based on the method of extended system center. A higher‐order sliding mode observer/differentiator is used for the exact estimation of the input–output states in a finite time. The bounded disturbance is reconstructed asymptotically. A numerical example illustrates the efficiency of the proposed output‐feedback tracking approach developed for causal nonminimum phase nonlinear systems. Copyright © 2009 John Wiley & Sons, Ltd.  相似文献   

5.
Novel sliding mode observer (SMO) and robust nonlinear control methods are presented, which are shown to achieve finite‐time state estimation and asymptotic regulation of a fluid flow system. To facilitate the design and analysis of the closed‐loop active flow control (AFC) system, proper orthogonal decomposition–based model order reduction is utilized to express the Navier‐Stokes partial differential equations as a set of nonlinear ordinary differential equations. The resulting reduced‐order model contains a measurement equation that is in a nonstandard mathematical form. This challenge is mitigated through the detailed design and analysis of an SMO. The observer is shown to achieve finite‐time estimation of the unmeasurable states of the reduced‐order model using direct sensor measurements of the flow field velocity. The estimated states are utilized as feedback measurements in a closed‐loop AFC system. To address the practical challenge of actuator bandwidth limitations, the control law is designed to be continuous. A rigorous Lyapunov‐based stability analysis is presented to prove that the closed‐loop flow estimation and control method achieves asymptotic regulation of a fluid flow field to a prescribed state. Numerical simulation results are also provided to demonstrate the performance of the proposed closed‐loop AFC system, comparing 2 different designs for the SMO.  相似文献   

6.
A new sliding mode control (SMC) approach, output variables only, single phase only and chattering phenomenon free, is presented for a class of mismatched uncertain large-scale systems. For a new multitask SMC, it is not required that the system states are available. Moreover, the sliding function in this study just depends on output variables. Using an exponential type sliding surface, the system states are always in the sliding mode at the beginning time t = 0. Using a newly appropriate linear matrix inequality stability conditions by the Lyapunov method are derived such that each subsystem in the new sliding mode is completely invariant to matched uncertainties. As a result, robustness of the mismatched uncertain large-scale systems can be assured throughout an entire response of the system starting from the initial time t = 0. In every subsystem, a scheme of decentralised control using only output states is proposed. In addition, a continuous controller is finally designed for chattering removal. Finally, a numerical example is used to demonstrate the efficacy of the proposed method.  相似文献   

7.
In this article, we address the problem of fault reconstruction in delayed systems by introducing a time‐shifted sliding mode observer (SMO). While time‐varying delays of arbitrary duration are considered in the measured output signal, the actuator fault is parametrized as a weighted sum of known regressor functions with unknown coefficients. The prediction scheme utilizes the variation of constants formula to obtain the present time estimate of the unmeasured state. The fault is also identified at present time by means of the continuous‐time Least Squares approaches. Ideal sliding mode can be guaranteed in theory, even in the presence of such adverse delays, since there is no chattering in the output estimation error of the SMO. An application to petroleum engineering with numerical simulations is presented to show the effectiveness of the proposed method.  相似文献   

8.
Terminal sliding mode observers for a class of nonlinear systems   总被引:1,自引:0,他引:1  
Chee Pin Tan  Xinghuo Yu 《Automatica》2010,46(8):1401-1404
This paper proposes a terminal sliding mode observer for a class of nonlinear systems to achieve finite time convergence for all error states. Compared to standard sliding mode observers which only enable finite time convergence of the output error, the observer in this paper makes use of fractional powers to reduce other non-output errors to zero in finite time. A 2-degree-of-freedom robotic manipulator is used to demonstrate the effectiveness of the proposed observer.  相似文献   

9.
This paper presents a fast terminal sliding‐mode tracking control for a class of uncertain nonlinear systems with unknown parameters and system states combined with time‐varying disturbances. Fast terminal sliding‐mode finite‐time tracking systems based on differential evolution algorithms incorporate an integral chain differentiator (ICD) to feedback systems for the estimation of the unknown system states. The differential evolution optimization algorithm using ICD is also applied to a tracking controller, which provides unknown parametric estimation in the limitation of unknown system states for trajectory tracking. The ICD in the tracking systems strengthens the tracking controller robustness for the disturbances by filtering noises. As a powerful finite‐time control effort, the fast terminal sliding‐mode tracking control guarantees that all tracking errors rapidly converge to the origin. The effectiveness of the proposed approach is verified via simulations, and the results exhibit high‐precision output tracking performance in uncertain nonlinear systems.  相似文献   

10.
This paper presents a simple and systematic approach to design second order sliding mode controller for buck converters. The second order sliding mode control (SOSMC) based on twisting algorithm has been implemented to control buck switch mode converter. The idea behind this strategy is to suppress chattering and maintain robustness and finite time convergence properties of the output voltage error to the equilibrium point under the load variations and parametric uncertainties. In addition, the influence of the twisting algorithm on the performance of closed-loop system is investigated and compared with other algorithms of first order sliding mode control such as adaptive sliding mode control (ASMC), nonsingular terminal sliding mode control (NTSMC).In comparative evaluation, the transient response of the output voltage with the step change in the load and the start-up response of the output voltage with the step change in the input voltage of buck converter were compared. Experimental results were obtained from a hardware setup constructed in laboratory. Finally, for all of the surveyed control methods, the theoretical considerations, numerical simulations, and experimental measurements from a laboratory prototype are compared for different operating points. It is shown that the proposed twisting method presents an improvement in steady state error and settling time of output voltage during load changes.   相似文献   

11.
This work focuses on the problem of observer-based robust speed sensorless control of a 3-phase permanent magnet synchronous motor (PMSM). Nonlinear design techniques are employed for designing robust speed controller and observer that are able to withstand the effects of modelling uncertainties and load variations. A new cascaded observer scheme is proposed comprising a continuous sliding mode observer (SMO) and an extended high-gain observer (EHGO). The proposed cascaded observer reduces chattering, exhibits reasonable insensitivity to modelling inaccuracies and is capable of withstanding errors due to the finite boundary layer of continuous SMO. For the robust speed control, an integral sliding mode controller is designed that yields fast and accurate speed tracking performance even in the presence of bounded uncertainties and external disturbances. The complete scheme has been evaluated using simulations and experiments.  相似文献   

12.
孙一品  丁学明 《测控技术》2019,38(2):137-141
为了解决传统滑模观测器方法应用在永磁同步电机无传感器矢量控制时所产生的抖振问题,使用RBF神经网络动态调节观测器的切换增益,即使其输入为传统滑模估计方案中的电流估计误差,输出为滑模增益;同时为了简化系统结构、提高方案可行性,将RBF神经网络设计为单输入单输出的结构,并将网络的学习和工作过程融合,使其在自身网络参数的不断优化中实时输出滑模增益,以增强系统鲁棒性。最后通过Matlab/Simulink软件对该系统进行建模仿真,并将该方法与传统滑模观测器方法进行对比。实验结果表明,该方案能够为矢量控制提供更加准确的转子位置及速度信息,提高了整个电机控制系统的稳定性。  相似文献   

13.
A new dynamic terminal sliding mode control (DTSMC) technique is proposed for a class of single-input and single-output (SISO) uncertain nonlinear systems. The dynamic terminal sliding mode controller is formulated based on Lyapunov theory such that the existence of the sliding phase of the closed-loop control system can be guaranteed, chattering phenomenon caused by the switching control action can be eliminated, and high precision performance is realized. Moreover, by designing terminal equation, the output tracking error converges to zero in finite time, the reaching phase of DSMC is eliminated and global robustness is obtained. The simulation results for an inverted pendulum are given to demonstrate the properties of the proposed method.  相似文献   

14.
A new dynamic terminal sliding mode control (DTSMC) technique is proposed for a class of single-input and single-output (SISO) uncertain nonlinear systems. The dynamic terminal sliding mode controller is formulated based on Lyapunov theory such that the existence of the sliding phase of the closed-loop control system can be guaranteed, chattering phenomenon caused by the switching control action can be eliminated, and high precision performance is realized. Moreover, by designing terminal equation, the output tracking error converges to zero in finite time, the reaching phase of DSMC is eliminated and global robustness is obtained. The simulation results for an inverted pendulum are given to demonstrate the properties of the proposed method.  相似文献   

15.
We propose an output feedback second‐order sliding mode controller to stabilize the cart on a beam system. A second‐order sliding mode controller is designed using a Lyapunov function‐based switching surface and finite‐time controllers, while the state estimator is designed based on the Luenberger‐like observer. The proposed observer extends the applicability of Luenberger‐like observer to nonlinear systems that are not input–output linearizable, but can be approximately input–output linearized. The approximation is based on the physical property of the system, wherein certain terms in the total energy are neglected. Extensive numerical simulations validate the robustness of the proposed controller to parametric uncertainties using estimated states. Copyright © 2009 John Wiley & Sons, Ltd.  相似文献   

16.
The posture stabilization of a unicycle mobile robot is useful in executing parking and docking maneuvers. It becomes more advantageous to guarantee the posture stabilization in finite time for a battery operated robot, especially in an application involving multiple robots. This paper addresses the posture stabilization of the unicycle mobile robot in finite time, especially when only the position information is available. We adopt the reaching law approach and design a discrete‐time sliding mode (DSM) controller by finitely discretizing the chained form of the unicycle, using the notion of multirate input sampling. Finite‐time stabilization of the equilibria is achieved by using multirate piecewise continuous inputs. Furthermore, the control inputs are realized using multirate output‐feedback (MROF) technique, wherein the states are estimated using the knowledge of the past fast output samples and immediate past control inputs. The proposed MROF‐DSM strategy avoids undesirable chatter in the system response owing to the nonswitching‐type controller and guarantees the stabilization in finite time. Simulations demonstrate the efficacy of the proposed method.  相似文献   

17.
The problem of output control in multiple‐input–multiple‐output nonlinear systems is addressed. A high‐order sliding‐mode observer is used to estimate the states of the system and identify the discrepancy between the nominal model and the real plant. The exact and finite‐time estimation may be tackled as long as the system presents the algebraic strong observability property. Thus, a continuous robust input‐output linearization strategy can be obtained with respect to a prescribed output. As a consequence, the closed‐loop dynamics performs robustly to uncertainties/perturbations. To illustrate the advantages of the proposed method, we introduce a study case that demands a robust linear system behavior: the self‐oscillations induced in an underactuated mechanical system through a two‐relay controller. Experiments with an inertial wheel pendulum illustrate the feasibility of the proposed approach.  相似文献   

18.
19.
In this paper, a terminal sliding mode observer (TSMO) for systems with general state‐space representation is proposed. The effects of uncertainties and matched disturbances are incorporated in the system dynamics. Compared to conventional sliding mode observers, which are capable of finite time convergence of the measured states’ (outputs) errors and asymptotic convergence of unmeasured states’ errors, the proposed TSMO guarantees finite time convergence of all states. Three appropriate Lyapunov functions are defined for proving robust and finite time convergence of all state estimation errors of the TSMO. In addition, to highlight the effectiveness of the methodology, the developed TSMO is applied to a well‐known realistic wind turbine model. Results confirm that the proposed TSMO estimates all the states in finite time with good accuracy.  相似文献   

20.
The paper describes a theoretical framework for the design of a robust multivariable output tracking controller using sliding mode concepts. The approach assumes that only measured outputs are available and uses a sliding mode observer to reconstruct estimates of the internal system states for use in a full information sliding mode control law. This scheme is applied to a control problem associated with high temperature furnaces. The paper describes the synthesis of the proposed control scheme from design through to implementation on an industrial test facility. © 1997 by John Wiley & Sons, Ltd.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号