Synthesis,effectiveness, and working mechanism of humic acid‐{sodium 2‐acrylamido‐2‐methylpropane sulfonate‐co‐N,N‐dimethyl acrylamide‐co‐acrylic acid} graft copolymer as high‐temperature fluid loss additive in oil well cementing

Monomers of 2‐acrylamido‐2‐methylpropane sulfonic acid (AMPS®), N,N–dimethyl acrylamide (NNDMA) and acrylic acid (AA) were grafted on humic acid as backbone by aqueous free radical copolymerization in such a manner that a graft copolymer possessing lateral terpolymer chains was obtained. Molar ratios between AMPS®, NNDMA, and AA were found to be 1 : 1.54 : 0.02 and the ratio between backbone and graft chain was 20 : 80 wt %. The synthesized fluid loss additive (FLA) was characterized by size exclusion chromatography (SEC), charge titration, and Brookfield viscometry. Thermogravimetric and SEC analysis revealed stretched backbone worm architecture for the polymer whereby humic acid constitutes the backbone decorated with lateral graft chains. Grafting was confirmed by SEC data (R_g) and by ineffectiveness of a blend of AMPS®‐NNDMA‐AA copolymer with humic acid. Their performance as high temperature FLA was studied at 150°C by measuring static filtration properties of oil well cement slurries containing 35% bwoc of silica fume and 1.2% bwoc AMPS®‐co‐itaconic acid retarder. At this temperature, 1.0% bwoc graft copolymer achieves API fluid loss value of 40 mL, thus confirming high effectiveness. The graft copolymer viscosifies cement slurries less than other common synthetic FLAs. The working mechanism of the graft copolymer was found to rely on adsorption onto surface of hydrating cement, as was evidenced by adsorption and zeta potential measurements. Adsorption is hardly affected by temperature and results in constriction of the filter cake pores. The study provides insight into performance of cement additives under the harsh conditions of high temperature and high pressure. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Competitive adsorption between an AMPS®‐based fluid loss polymer and Welan gum biopolymer in oil well cement

Water‐soluble 2‐acrylamido‐2‐methylpropane sulfonic acid (AMPS®)‐based copolymers are commonly used to provide water retention (fluid loss control) for oil well cement slurries. Here, the fluid loss performance of a CaAMPS®‐N,N‐dimethylacrylamide copolymer (CaAMPS®‐co‐NNDMA) in the presence of Welan gum, an anionic microbial biopolymer produced by anaerobic fermentation using Alcaligenes ATCC 31555 bacteria was investigated at 80°C. Welan gum is used to control unwanted free water development at the surface of the cement slurry. The effectiveness of CaAMPS®‐co‐NNDMA fluid loss additive (FLA) solely relies on its high adsorption onto the positively charged surfaces of cement hydrates. Adsorption of the FLA is, however, perturbed by Welan gum. This anionic polysaccharide competes with CaAMPS®‐co‐NNDMA for adsorption sites on the cement surface. This effect is surprising because in cement pore solution, Welan gum exhibits a much lower specific anionic charge amount than CaAMPS®‐co‐NNDMA. The reason is that Welan gum possesses carboxylate functionalities, which are much stronger anchor groups than the sulfonate groups present in CaAMPS®‐co‐NNDMA. The superiority of the carboxylate groups regarding their affinity to the mineral surface, which possesses insufficiently coordinated Ca atoms is confirmed by a higher calcium binding capability for Welan gum than for the FLA. Thus, Welan gum can reduce effectiveness of CaAMPS®‐co‐NNDMA as fluid loss agent by preventing its adsorption or through displacement of already adsorbed FLA molecules from the surface of cement. In multiadmixture systems, which are commonly used in oil well cement, concrete or mortars, competitive adsorption between different additives for surface sites can negatively impact the performance of these additives. Understanding the reasons behind can help to develop more effective admixture systems. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Effect of high temperature and the role of sulfate on adsorption behavior and effectiveness of AMPS®‐based cement fluid loss polymers

The fluid loss control performance of 2‐acrylamido‐2‐methylpropane sulfonic acid (AMPS®)‐based copolymers added to cement slurries was studied at 27 and 100°C, respectively. It was found that effectiveness of these fluid loss additives solely relies on achievement of a high adsorbed amount on the surface of cement. At elevated temperature (100°C), CaAMPS®‐N,N‐dimethyl acrylamide copolymer (CaAMPS®‐co‐NNDMA) exhibits reduced adsorption and hence decreased fluid loss control of the cement slurry. The reason behind this behavior is poor calcium binding capability of the sulfonate anchor groups, which coordinate with calcium atoms present on the mineral surface. Whereas, an increase in the sulfate concentration present in cement pore solution instigates partial coiling of CaAMPS®‐co‐NNDMA and causes only a slight influence on the performance of this copolymer. The elevated sulfate content results from thermal degradation of ettringite, a cement hydrate mineral produced during the early stages of cement hydration. Incorporation of minor amounts (～ 1.3 mol %) of maleic anhydride into this copolymer produces a terpolymer, which exhibits higher and more stable adsorption, even at high temperature. This effect is owed to the presence of homopolymer blocks of polycarboxylates distributed along the polymer trunk. On mineral surfaces, they present much stronger anchor groups than sulfonate functionalities, as evidenced by their higher calcium binding capability. Consequently, fluid loss performance of CaAMPS®‐co‐NNDMA‐co‐MA is little affected by temperature. Understanding the influence of temperature on the physicochemical interactions occurring between additives and the mineral surface can help to design more effective admixtures suitable for high temperature applications. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Working mechanism of a high temperature (200°C) synthetic cement retarder and its interaction with an AMPS®‐based fluid loss polymer in oil well cement

A copolymer comprising of 2‐acrylamido‐2‐methyl propane sulfonic acid (AMPS®) and itaconic acid (molar ratio 1 : 0.32) was synthesized by aqueous free radical polymerization and probed as high temperature retarder for oil well cement. Characteristic properties of the copolymer including molar masses (M_w and M_n), polydispersity index and anionic charge amount were determined. The copolymer possesses a M_w of ～ 2 × 10⁵ g/mol and is highly anionic. HT/HP consistometer tests confirmed effectiveness of the retarder at temperatures up to 200°C. The working mechanism of NaAMPS®‐co‐itaconic acid was found to rely exclusively on its huge calcium binding capacity (5 g calcium/g copolymer). It reduces the amount of freely dissolved, nonbound calcium ions present in cement pore solution and thus hinders the growth of cement hydrates because of lack of calcium. The value for the calcium binding capability is 46 times higher than the stoichiometric amount per ? COO^? functionality. Consequently, calcium also coordinates to other donor atoms present in the retarder. NaAMPS®‐co‐itaconic acid also adsorbs onto cement, as was evidenced by TOC analysis of cement filtrates, zeta potential measurement and decreased rheology of cement pastes. However, adsorption plays no role in the retarding mechanism of this copolymer. Combination of NaAMPS®‐co‐itaconic acid retarder with a common CaAMPS®‐co‐NNDMA fluid loss additive (FLA) revealed that competitive adsorption on cement between these two admixtures occurs. The retarder fills interstitial adsorption sites on cement located between those occupied by the larger FLA molecules. In consequence, fewer amounts of CaAMPS®‐co‐NNDMA can adsorb and its effectiveness is reduced. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Synthesis and application of 2‐acrylamido‐2‐methyl propane sulfonic acid/acrylamide/N,N‐dimethyl acrylamide/maleic anhydride as a fluid loss control additive in oil well cementing

Using 2‐acrylamido‐2‐methyl propane sulfonic acid (AMPS), acrylamide (AM), N,N‐dimethyl acrylamide (NNDMA), and maleic anhydride (MA), a new dispersive type fluid loss control additive (FLCA) AMPS/AM/NNDMA/MA (PANM) was synthesized by free radical aqueous solution copolymerization, and the new FLCA could be used without dispersant existing in the cement. The optimal PANM (OPANM) was obtained under the optimum reaction conditions: mole ratio of AMPS/AM/NNDMA/MA = 4/2.5/2.5/1, monomer concentration = 32.5%, amount of (by weight of monomer) ammonium persulfate/sodium bisulfate = 1.0%, pH value = 4, and temperature = 40°C. The synthesized copolymer OPANM was identified by FTIR analysis. The evaluation results show the OPANM has excellent dispersing power, fluid loss control ability, thermal resistant, and salt tolerant ability. The OPANM was even stable when the temperature was below 300°C proved by TG analysis. The thickening time of the slurry containing the synthesized additive reduces as the temperature increases. The copolymer OPANM is expected to be an excellent FLCA. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Effect of different anchor groups on adsorption behavior and effectiveness of poly(N,N‐dimethylacrylamide‐co‐Ca 2‐acrylamido‐2‐methylpropanesulfonate) as cement fluid loss additive in presence of acetone–formaldehyde–sulfite dispersant

The impact of various anchor groups on adsorption behavior of AMPS® copolymers was studied. The anchor groups differ in anionic charge density. Copolymer adsorption and water retention of oil well cement slurries achieved from CaAMPS®‐co‐NNDMA in the presence of an acetone–formaldehyde–sulfite (AFS) dispersant were improved by incorporation of minor amounts (～ 1% by weight of polymer) of acrylic acid (CaAMPS®‐co‐NNDMA‐co‐AA), maleic acid anhydride (CaAMPS®‐co‐NNDMA‐co‐MAA), or vinyl phosphonic acid (CaAMPS®‐co‐NNDMA‐co‐VPA), respectively. Performance of these terpolymers was studied by measuring static filtration properties of oil well cement slurries at 27°C and 70 bar pressure. All fluid loss additives possess comparable molar masses and show the same adsorption behavior and effectiveness when no other admixture is present. In the presence of AFS dispersant, however, adsorption of CaAMPS®‐co‐NNDMA and hence fluid loss control is dramatically reduced, whereas effectiveness of CaAMPS®‐co‐NNDMA‐co‐AA is less influenced because of acrylic acid incorporated as additional anchor group. Even more, CaAMPS®‐co‐NNDMA‐co‐MAA combined with AFS allows simultaneous adsorption of both polymers and thus produces good fluid loss control. CaAMPS®‐co‐NNDMA‐co‐VPA no longer allows adsorption of AFS dispersant. This was also confirmed by rheological measurements. The results show that, in a binary admixture system, adsorption of the anionic polymer with anchor groups possessing higher charge density is preferred. Surface affinity of the anchor groups studied increase in the order ? SO → ? COO^? → vic‐(? COO^?)₂→ ? PO. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Poly(N‐isopropylacrylamide) grafted to a strongly charged backbone: Thermoresponsive behavior in aqueous solution

The thermoresponsive properties in aqueous solution of the graft copolymer poly(acrylic acid‐co‐2‐acrylamido‐2‐methyl propane sulfonic acid)‐g‐poly(N‐isopropylacrylamide) [P(AA‐co‐AMPSA)‐g‐PNIPAM] were studied and compared to the corresponding behavior of the poly(acrylic acid)‐g‐poly(N‐isopropylacrylamide) (PAA‐g‐PNIPAM) graft product. Both products contain about 40% (w/w) of PNIPAM, whereas the backbone, P(AA‐co‐AMPSA), of the first copolymer contains about 40% of AMPSA mole units. The strongly charged P(AA‐co‐AMPSA)‐g‐PNIPAM graft copolymer was water soluble over the whole pH range, whereas the PAA‐g‐PNIPAM copolymer precipitated out from water at pH < 4. As a result, the first product exhibited a temperature‐sensitive behavior in a wide pH range, extended in the acidic region, whereas in semidilute aqueous solutions, an important thermothickening behavior was observed, even at low pH (pH = 3.0). © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 3466–3470, 2004     

Grafting of poly(3‐hydroxyalkanoate) and linoleic acid onto chitosan

Poly(3‐hydroxy octanoate) (PHO), poly(3‐hydroxy butyrate‐co‐3‐hydroxyvalerate) (PHBV), and linoleic acid were grafted onto chitosan via condensation reactions between carboxylic acids and amine groups. Unreacted PHAs and linoleic acid were eliminated via chloroform extraction and for elimination of unreacted chitosan were used 2 wt % of HOAc solution. The pure chitosan graft copolymers were isolated and then characterized by FTIR, ¹³C‐NMR (in solid state), DSC, and TGA. Microbial polyester percentage grafted onto chitosan backbone was varying from 7 to 52 wt % as a function of molecular weight of PHAs, namely as a function of steric effect. Solubility tests were also performed. Graft copolymers were soluble, partially soluble or insoluble in 2 wt % of HOAc depending on the amount of free primary amine groups on chitosan backbone or degree of grafting percent. Thermal analysis of PHO‐g‐Chitosan graft copolymers indicated that the plastizer effect of PHO by means that they showed melting transitions T_ms at 80, 100, and 113°C or a broad T_ms between 60.5–124.5°C and 75–125°C while pure chitosan showed a sharp T_m at 123°C. In comparison of the solubility and thermal properties of graft copolymers, linoleic acid derivatives of chitosan were used. Thus, the grafting of poly(3‐hydroxyalkanoate) and linoleic acid onto chitosan decrease the thermal stability of chitosan backbone. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103:81–89, 2007     

Synthesis of wheat straw composite superabsorbent

A novel wheat straw composite superabsorbent was prepared by graft polymerization with acrylic acid (AA), acrylamide (AM), and maleic anhydride‐modified wheat straw in aqueous solution, using N,N‐methylene‐bis‐acrylamide (MBA) as a cross‐linker and ammonium persulfate (APS) and sodium bisulfite (SBS) as redox initiators. Factors influencing the degree of carboxylation, such as reaction time, reaction temperature, and the amount of maleic anhydride, were investigated. Morphologies and structure of the wheat straw composite superabsorbent were characterized by fourier transform infrared spectroscopy (FTIR), scanning electron microscope (SEM), and X‐ray diffraction (XRD). Water absorption of wheat straw composite superabsorbent was rapid, requiring 13.1 min to reach 63% of equilibrium absorbency (781 g/g). FTIR spectra indicate that maleic anhydride has been reacted onto the wheat straw backbone and the structure of wheat straw graft copolymer is formed. SEM data show that the fibrous morphology of wheat straw disappears and gel aggregates with many large microporous holes are formed after wheat straw graft modification. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 3404–3410, 2013     

Synthesis,characterization, and working mechanism of a synthetic high temperature (200°C) fluid loss polymer for oil well cementing containing allyloxy‐2‐hydroxy propane sulfonic (AHPS) acid monomer

A polymer comprising of 2‐acrylamido‐2‐methyl propane sulfonic acid, N, N‐dimethyl acrylamide, allyloxy‐2‐hydroxy propane sulfonic acid (AHPS), acrylic acid, and N, N‐methylene bisacrylamide was synthesized by aqueous free radical copolymerization and tested as high temperature performing fluid loss additive (FLA) in oil well cement. Successful incorporation of AHPS was confirmed and characteristic properties of the copolymer were determined using size exclusion chromatography. The FLA showed excellent water retention in cement at 200°C/70 bar. At this temperature, polymer structure changed from branched to linear and hydrodynamic size decreased by ～50%, thus indicating potential fragmentation, while performance remained unaffected by these alterations. The FLA copolymer does not viscosify cement slurries which is advantageous in high temperature well cementing. The working mechanism of the AHPS‐based copolymer was found to rely on reduction of filtercake permeability which is caused by a voluminous coprecipitate of the FLA with tartaric acid retarder, mediated by Ca²⁺ ions. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Preparation and characterization of polyaniline N‐grafted with poly(ethyl acrylate) synthesized via atom transfer radical polymerization

Polyaniline (PANI) N‐grafted with poly(ethyl acrylate) (PEA) was synthesized by the grafting of bromo‐terminated poly (ethyl acrylate) (PEA‐Br) onto the leucoemeraldine form of PANI. PEA‐Br was synthesized by the atom transfer radical polymerization of ethyl acrylate in the presence of methyl‐2‐bromopropionate and copper(I) chloride/bipyridine as the initiator and catalyst systems, respectively. The leucoemeraldine form of PANI was deprotonated by butyl lithium and then reacted with PEA‐Br to prepare PEA‐g‐PANI graft copolymers containing different amounts of PEA via an N‐grafting reaction. The graft copolymers were characterized by Fourier transform infrared spectroscopy, elemental analysis, and thermogravimetric analysis. Solubility testing showed that the solubility of PANI in chloroform was increased by the grafting of PEA onto PANI. The morphology of the PEA‐g‐PANI graft copolymer films was observed by scanning electron microscopy to be homogeneous. The electrical conductivity of the graft copolymers was measured by the four‐probe method. The results show that the conductivity of the PANI decreased significantly with increasing grafting density of PEA onto the PANI backbone up to 7 wt % and then remained almost constant with further increases in the grafting percentage of PEA. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Modification of the molar anionic charge density of acetone–formaldehyde–sulfite dispersant to improve adsorption behavior and effectiveness in the presence of CaAMPS®‐co‐NNDMA cement fluid loss polymer

Sulfonated aldol polycondensates were synthesized from acetone, formaldehyde, and different amounts of sodium sulfite, resulting in polymers with varying degrees of sulfonation (DS). The anionic charge amount of these macromolecules measured by polyelectrolyte titration decreased with lower DS. The effectiveness of the acetone–formaldehyde–sulfite (AFS) polycondensates as cement dispersant was found to depend on the amount of polymer adsorbed on cement. AFS adsorption decreases with lower DS. Interaction and compatibility between AFS and CaAMPS®‐co‐NNDMA fluid loss additive was studied by formulating binary additive systems composed of one of the modified AFS polymers and CaAMPS‐co‐NNDMA. At high DS, AFS adsorbs strongly and prevents CaAMPS‐co‐NNDMA from adsorbing in sufficient amounts on the cement surface. The result is poor fluid loss control of the cement slurry. AFS polymers with lower DS, however, allow simultaneous adsorption of both polymers in sufficient quantities to provide good fluid loss control and low rheology at the same time. Thus, effectiveness of both additives was retained. Obviously, effectiveness of such multi‐admixture systems depends on the adjustment of the adsorption behavior of the individual components relative to each other. Molar anionic charge density of the polymers was found to be a major parameter influencing their relative adsorption behavior. The AFS polymer with DS = 0.2 possesses a molar anionic charge density comparable to CaAMPS‐co‐NNDMA. Thus, when admixtures with similar molar anionic charge densities are used, the performance of one component is not negatively influenced by the other. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Phase behavior of temperature‐ and pH‐sensitive poly(acrylic acid‐g‐N‐isopropylacrylamide) in dilute aqueous solution

Several different composition temperature‐ and pH‐sensitive poly(acrylic acid‐g‐N‐isopropylacrylamide) (P(AA‐g‐NIPAM)) graft copolymers were synthesized by free‐radical copolymerization utilizing macromonomer technique. The phase behavior and conformation change of P(AA‐g‐NIPAM) in aqueous solutions were investigated by UV–vis transmittance measurements, fluorescence probe, and fluorescence quenching techniques. The results demonstrate that the P(AA‐g‐NIPAM) copolymers have temperature‐ and pH‐sensitivities, and these different composition graft copolymers have different lower critical solution temperature (LCST) and critical phase transition pH values. The LCST of graft copolymer decreases with increasing PNIPAM content, and the critical phase transition pH value increases with increasing Poly(N‐isopropylacrylamide) (PNIPAM) content. At room temperature (20°C), different composition of P(AA‐g‐NIPAM) graft copolymers in dilute aqueous solutions (0.001 wt %) have a loose conformation, and there is no hydrophobic microdomain formation within researching pH range (pH 3 ～ 10). In addition, for the P(AA‐g‐NIPAM) aqueous solutions, transition from coil to globular is an incomplete reversible process in heating and cooling cycles. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Graft copolymerization of acrylic acid onto cellulose: Effects of pretreatments and crosslinking agent

The graft copolymerization of acrylic acid (AA) and 2‐acrylamido 2‐methylpropane sulfonic acid (AASO₃H) onto cellulose, in the presence or absence of crosslinking agent N,N′‐methylene bisacrylamide (NMBA), by using different concentrations of ceric ammonium nitrate (CAN) initiator in aqueous nitric acid solution at either 5 or 30°C was investigated. To investigate the effect of pretreatment of cellulose on the copolymerization, before some grafting reactions cellulose was pretreated with either 2 or 20 wt % NaOH solutions or heated in distilled water/aqueous nitric acid (2.5 × 10^?3 M) at 55°C. To determine how the excess of initiator affects the grafting and homopolymerization, separate reactions were carried out by removing the excess of ceric ions by filtration of the mixture of initiator solution and cellulose before the monomer addition. Extraction‐purified products were characterized by grafting percentage and equilibrium swelling capacity. Pretreatment of cellulose with NaOH solutions decreased the grafting percentage of copolymers. In the case of AA–AASO₃H mixtures, nonpretreated cellulose gave a higher grafting percentage than NaOH‐pretreated cellulose. Filtration also lowered the grafting of AA on the cellulose in the cases of pretreatment with either water or nitric acid. Copolymers with the highest grafting percentage (64.8%) and equilibrium swelling value (105 g H₂O/g copolymer) were obtained in grafting reactions carried out in the presence of NMBA at 5°C. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 2267–2272, 2001     

Hydrophobically associating acrylamide‐based copolymer for chemically enhanced oil recovery

A hydrophobically associating copolymer was prepared by free‐radical polymerization with acrylamide (AM), acrylic acid (AA), and N‐allyloctadec‐9‐enamide (NAE) as monomers. The structure was characterized by Fourier transform infrared spectroscopy, ¹H‐NMR, ¹³C‐NMR, and scanning electron microscopy. The rheological experiments indicated that the copolymer possessed superior properties compared with partially hydrolyzed polyacryamide. It was found that an AM/AA/NAE/Tween‐80 system could effectively decrease the interfacial tension and reduce the surfactant loss caused by stratum adsorption in polymer–surfactant flooding. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 2901–2911, 2013     

Poly(ε‐caprolactone)‐grafted acetylated anhydroglucose oligomer by ring‐opening polymerization—Synthesis and characterization

A novel acetylated anhydroglucose oligomer (AGU‐oligomer), prepared by acid catalyzed transglycosidation of potato starch triacetate and ethylene glycol, was used as a multifunctional coinitiator for the ring‐opening polymerization of ε‐caprolactone (ε‐CL). The polymers were synthesized using different weight ratios of the starting materials and were characterized by NMR, SEC, and MALLS. The results confirmed the expected P(AGU/CL) polymer structure, namely a ‘comb‐like’ graft‐copolymer having the AGU oligomer as backbone with PCL grafts of variable chain lengths (L_CL = 4–21). Thermal and mechanical properties of graft‐copolymers with different ε‐CL block lengths were examined. By changing the graft length, crystallinity was controlled and amorphous polymers were obtained with AGU‐oligomer contents higher than 50 wt %. The tensile properties varied with the composition and a copolymer having 40 wt % of AGU‐oligomer behaved like soft elastomer, showing high elongation at break. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 1633–1641, 2006     

Graft copolymerization of thiophene onto polystyrene synthesized via nitroxide‐mediated polymerization and its polymer − clay nanocomposite

A new strategy for graft copolymerization of thiophene onto a polystyrene (PSt) backbone by a multi‐step process is suggested and the effects of an organoclay on the final properties of the graft copolymer sample are described. For this purpose, first poly(styrene‐co‐4‐chloromethyl styrene) [P(St‐co‐CMSt)] was synthesized via nitroxide‐mediated polymerization. Afterwards, the chlorine groups of P(St‐co‐CMSt) were converted to thiophene groups using the Kumada cross‐coupling reaction and thiophene‐functionalized PSt multicenter macromonomer (ThPStM) was synthesized. The graft copolymerization of thiophene monomers onto PSt was initiated by oxidized thiophene groups in the PSt chains after addition of ferric chloride (FeCl₃), an oxidative catalyst for polythiophene synthesis, and FeCl₃‐doped polythiophene was chemically grafted onto PSt chains via oxidation polymerization. The graft copolymer obtained was characterized by ¹H NMR and Fourier transform infrared spectroscopy, and its electroactivity behavior was verified under cyclic voltammetric conditions. Finally, PSt‐g‐PTh/montmorillonite nanocomposite was prepared by a solution intercalation method. The level of dispersion of organoclay and the microstructure of the resulting nanocomposite were probed by means of XRD and transmission electron microscopy. It was found that the addition of only a small amount of organoclay (5 wt%) was enough to improve the thermal stabilities of the nanocomposite.© 2013 Society of Chemical Industry     

Competitive removal of heavy metal ions by cellulose graft copolymers

The effect of composition of graft chains of four types cellulose graft copolymers on the competitive removal of Pb²⁺, Cu²⁺, and Cd²⁺ ions from aqueous solution was investigated. The copolymers used were (1) cellulose‐g‐polyacrylic acid (cellulose‐g‐pAA) with grafting percentages of 7, 18, and 30%; (2) cellulose‐g‐p(AA–NMBA) prepared by grafting of AA onto cellulose in the presence of crosslinking agent of N,N′‐methylene bisacrylamide (NMBA); (3) cellulose‐g‐p(AA–AASO₃H) prepared by grafting of a monomer mixture of acrylic acid (AA) and 2‐acrylamido‐2‐methyl propane sulphonic acid (AASO₃H) containing 10% (in mole) AASO₃H; and (4) cellulose‐g‐pAASO₃H obtained by grafting of AASO₃H onto cellulose. The concentrations of ions which were kept constant at 4 mmol/L in an aqueous solution of pH 4.5 were equal. Metal ion removal capacities and removal percentages of the copolymers was determined. Metal ion removal capacity of cellulose‐g‐pAA did not change with the increase in grafting percentages of the copolymer and determined to be 0.27 mmol metal ion/g_copolymer. Although the metal removal rate of cellulose‐g‐p(AA–NMBA) copolymer was lower than that of cellulose‐g‐pAA, removal capacities of both copolymers were the same which was equal to 0.24 mmol metal ion/g_copolymer. Cellulose did not remove any ion under the same conditions. In addition, cellulose‐g‐pAASO₃H removed practically no ion from the aqueous solution (0.02 mmol metal ion/g_copolymer). The presence of AASO₃H in the graft chains of cellulose‐g‐p(AA–AASO₃H) created a synergistic effect with respect to metal removal and led to a slight increase in metal ion adsorption capability in comparison to that of cellulose‐g‐pAA. All types of cellulose copolymers were found to be selective for the removal of Pb²⁺ over Cu²⁺ and Cd²⁺. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 2034–2039, 2003     

Novel lignosulfonate/N,N-dimethylacrylamide/γ-methacryloxypropyl trimethoxy silane graft copolymer as a filtration reducer for water-based drilling fluids

The redox system consisting of ammonium persulfate and sodium bisulfite was used as initiator, N,N-dimethylacrylamide (DMAA) and γ-methacryloxypropyl trimethoxy silane (KH570) were grafted onto sodium lignosulfonate (LS) in aqueous solution as reaction monomers, and a novel LS/KH570/DMAA graft copolymer filtrate reducer was synthesized. The structure of the copolymer was characterized by Fourier transform infrared spectrometer and nuclear magnetic resonance instrument. The result revealed that DMAA and KH570 were successfully grafted onto sodium LS. In addition, the thermal stability of the copolymer was determined by thermogravimetric analyzer and the micromorphology of filter cake of water-based drilling fluids (WBDFs) containing LS/KH570/DMAA was analyzed by scanning electron microscopy. At the same time, the rheological and filtration properties of WBDFs containing copolymer with different concentrations were further evaluated. The results showed that when the copolymer concentration was 3 wt %, the fluid loss of bentonite-based drilling fluids was only 6.2 mL before aging, and 9.8 mL after aging at 180 °C for 16 h. The fluid-loss control mechanism of LS/KH570/DMAA was investigated through clay particle distribution analysis and zeta potential measurement of WBDFs. Moreover, the WBDFs containing copolymer exhibit excellent performance in reducing fluid loss under the invasion of calcium salts. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 137, 48274.     

Synthesis and application of a new vinyl copolymer superplasticizer

A new vinyl graft copolymer superplasticizer was synthesized by copolymerization of polyethylene glycol acrylate (PEGAA), polyethylene glycol biester of maleic acid and citric acid (PEGMC), acrylic acid (AA), sodium allylsulphonate (SAS), and methyl acrylate (MA). The effects of the vinyl monomers' molar ratio, initiator, reaction temperature, and reaction time on its application properties were investigated. The results show that the new vinyl graft copolymer superplasticizer has excellent application properties when the molar ratio of PEGAA, PEGMC, AA, SAS, and MA is 0.5 : 0.10 : 0.20 : 0.05 : 0.03 and the initiator ammonium persulfate [(NH₄)₂S₂O₈, APS] is 0.8 wt % at 80°C for 3 h. The vinyl monomers' conversion is 98.7%. The applied results show that the water‐reducing ratio and retardation solidification time of the superplasticizer reach 33.5% and 4 h, respectively. The applied concrete has excellent mechanical properties. Its molecular structure was characterized by nuclear magnetic resonance, Fourier transform infrared spectra, and gel permeation chromatography. It is characteristic of the new vinyl graft copolymer superplasticizer that citric acid (CA) and MA are introduced into the copolymer molecules. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010