Effect of acrylic acid neutralization on ‘livingness’ of poly[styrene‐ran‐(acrylic acid)] macro‐initiators for nitroxide‐mediated polymerization of styrene

BACKGROUND: The effect of acrylic acid neutralization on the degradation of alkoxyamine initiators for nitroxide‐mediated polymerization (NMP) was studied using styrene/acrylic acid and styrene/sodium acrylate random copolymers (20 mol% initial acrylate feed concentration) as macro‐initiators. The random copolymers were re‐initiated with fresh styrene in 1,4‐dioxane at 110 °C at SG1 mediator/BlocBuilder^® unimolecular initiator ratios of 5 and 10 mol%. RESULTS: The value of k_pK (k_p = propagation rate constant, K = equilibrium constant) was not significantly different for styrene/acrylic acid and styrene/sodium acrylate compositions at 110 °C (k_pK = 2.4 × 10^?6–4.6 × 10^?6 s^?1) and agreed closely with that for styrene homopolymerization at the same conditions (k_pK = 2.7 × 10^?6–3.0 × 10^?6 s^?1). All random copolymers had monomodal, narrow molecular weight distributions (polydispersity index M?_w/M?_n = 1.10–1.22) with similar number‐average molecular weights M?_n = 19.3–22.1 kg mol^?1. Re‐initiation of styrene/acrylic acid random copolymers with styrene resulted in block copolymers with broader molecular weight distributions (M?_w/M?_n = 1.37–2.04) compared to chains re‐initiated by styrene/sodium acrylate random copolymers (M?_w/M?_n = 1.33). CONCLUSIONS: Acrylic acid degradation of the alkoxyamines was prevented by neutralization of acrylic acid and allowed more SG1‐terminated chains to re‐initiate the polymerization of a second styrenic block by NMP. Copyright © 2008 Society of Chemical Industry     

Efficiency above 6% in poly(3‐hexylthiophene):phenyl‐C‐butyric acid methyl ester photovoltaics via simultaneous addition of poly(3‐hexylthiophene) based grafted graphene nanosheets and hydrophobic block copolymers

A combination of reduced graphene oxide (rGO) nanosheets grafted with regioregular poly(3‐hexylthiophene) (P3HT) (rGO‐g‐P3HT) and P3HT‐b‐polystyrene (PS) block copolymers was utilized to modify the morphology of P3HT:[6,6]‐phenyl‐C71‐butyric acid methyl ester (PC71BM) active layers in photovoltaic devices. Efficiencies greater than 6% were acquired after a mild thermal annealing. To this end, the assembling of P3HT homopolymers and P3HT‐b‐PS block copolymers onto rGO‐g‐P3HT nanosheets was investigated, showing that the copolymers were assembled from the P3HT side onto the rGO‐g‐P3HT nanosheets. Assembling of P3HT‐b‐PS block copolymers onto the rGO‐g‐P3HT nanosheets developed the net hole and electron highways for charge transport, thereby in addition to photoluminescence quenching the charge mobility (μ_h and μ_e) values increased considerably. The best charge mobilities were acquired for the P3HT₅₀₀₀₀:PC71BM:rGO‐g‐P3HT₅₀₀₀₀:P3HT₇₀₀₀‐b‐PS₁₀₀₀ system (μ_h = 1.9 × 10^?5 cm² V^–1 s^–1 and μ_e = 0.8 × 10^?4 cm² V^–1 s^–1). Thermal annealing conducted at 120 °C also further increased the hole and electron mobilities to 9.8 × 10^?4 and 2.7 × 10^?3 cm² V^–1 s^–1, respectively. The thermal annealing acted as a driving force for better assembly of the P3HT‐b‐PS copolymers onto the rGO‐g‐P3HT nanosheets. This phenomenon improved the short circuit current density, fill factor, open circuit voltage and power conversion efficiency parameters from 11.13 mA cm^?2, 0.63 V, 62% and 4.35% to 12.98 mA cm^?2, 0.69 V, 68% and 6.09%, respectively. © 2019 Society of Chemical Industry     

CuO‐filled aminomethylated polysulfone hybrid membranes for deep desulfurization

CuO‐filled aminomethylated polysulfone hybrid membranes were prepared for sulfur removal from gasoline. The as‐prepared membranes were characterized using Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), and X‐ray diffraction (XRD). The separation performance of the hybrid membranes was evaluated by pervaporation (PV) separation of n‐heptane/thiophene binary mixture. CuO‐filling leads to a decrease in permeation flux. The sulfur‐enrichment factor increased first and then decreased with increasing CuO loading, and it is worth noting that there is a rebound in enrichment factor above 8 wt % CuO loading. Influencing factors such as nitrogen content, feed temperature, sulfur content, and various hydrocarbons on membrane PV performance were also evaluated. Permeation flux of 23.9 kg·μm·m^?2·h^?1 and sulfur‐enrichment factor of 3.9 can be achieved at 4 wt % CuO loading in PV of n‐heptane/thiophene binary mixture with 1500 μg·g^?1 sulfur content. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 3718–3725, 2013     

Pure and complex nanostructures using poly[bis(triiso‐propylsilylethynyl) benzodithiophene‐bis(decyltetradecyl‐thien) naphthobisthiadiazole], carbon nanotubes and reduced graphene oxide for high‐performance polymer solar cells

Crystallization of poly[bis(triiso‐propylsilylethynyl) benzodithiophene‐bis(decyltetradecyl‐thien) naphthobisthiadiazole] (PBDT‐TIPS‐DTNT‐DT) was investigated in supramolecules based on carbon nanotubes (CNTs) and reduced graphene oxide (rGO) and their grafted derivatives. The principal peaks of PBDT‐TIPS‐DTNT‐DT crystals were in the range 3.50°–3.75°. By grafting the surface of the carbonic materials, the assembling of polymer chains decreased because of hindrance of poly(3‐dodecylthiophene) (PDDT) grafts against π‐stacking. The diameters of CNT/polymer and CNT‐g‐PDDT/polymer supramolecules were 160 and 100 nm. The rGO/polymer supramolecules had the highest melting point (T_m = 282 °C) and fusion enthalpy (ΔH_m = 25.98 J g^?1), reflecting the largest crystallites and the most ordered constituents. Nano‐hybrids based on grafted rGO (276 °C and 28.26 J g^?1), CNT (275 °C and 27.32 J g^?1) and grafted CNT (268 °C and 22.17 J g^?1) were also analyzed. T_m and ΔH_m values were significantly less in corresponding melt‐grown systems. The nanostructures were incorporated in active layers of PBDT‐TIPS‐DTNT‐DT:phenyl‐C₇₁‐butyric acid methyl ester (PC₇₁BM) solar cells to improve the photovoltaic features. The best results were detected for PBDT‐TIPS‐DTNT‐DT:PC₇₁BM:rGO/polymer systems having J_sc = 13.11 mA cm^?2, fill factor 60% and V_oc = 0.71 V with an efficacy of 5.58%. On grafting the rGO and CNT, efficiency reductions were 12.01% (5.58%–4.91%) and 9.34% (4.07%–3.69%), respectively. © 2019 Society of Chemical Industry     

Free‐standing hybrid anion‐exchange membranes for application in fuel cells

A series of free‐standing hybrid anion‐exchange membranes were prepared by blending brominated poly(2,6‐dimethyl‐1,4‐phenylene oxide) (BPPO) with poly(vinylbenzyl chloride‐co‐γ‐methacryloxypropyl trimethoxy silane) (poly(VBC‐co‐γ‐MPS)). Apart from a good compatibility between organic and inorganic phases, the hybrid membranes had a water uptake of 32.4–51.8%, tensile strength around 30 MPa, and T_d temperature at 5% weight loss around 243–261°C. As compared with the membrane prepared from poly (VBC‐co‐γ‐MPS), the hybrid membranes exhibited much better flexibility, and larger ion‐exchange capacity (2.19–2.27 mmol g^?1) and hydroxyl (OH^?) conductivity (0.0067–0.012 S cm^?1). In particular, the hybrid membranes with 60–75 wt % BPPO had the optimum water uptake, miscibility between components, and OH^? conductivity, and were promising for application in fuel cells. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Synthesis of borate ester‐grafted carboxylated acrylonitrile butadiene rubber and its use as electron acceptor to dissolve lithium perchlorate

A novel borate ester (BE)‐grafted carboxylated acrylonitrile butadiene rubber (XNBR) was synthesized. From Fourier transform infrared, ¹H NMR and elemental analyses, the borate ester was successfully grafted to XNBR, resulting in a more flexible XNBR chain as revealed by differential scanning calorimetry. The binding energies of boron, oxygen, lithium and chlorine atoms of XNBR‐g‐BE–LiClO₄ are quite different from those of XNBR or LiClO₄. Meanwhile, the wavenumbers of C? O? B? O? C, C?O and C? H vibrations of the benzene ring shift towards lower values and a new shoulder peak for ? CN at about 2260 cm^?1 emerges. By integrating fitting peak areas of ? CN groups and ClO₄^?, the fractions of ? CN group and ClO₄^? bidentate bonding in XNBR‐g‐BE–LiClO₄ are much higher than in NBR–LiClO₄. Based on these experiments, a possible dissociation mechanism is proposed in which the boron atom of XNBR‐g‐BE receives electron pairs from ClO₄^?, releasing partial positive charge of Li⁺ to bind with ? CN group. © 2016 Society of Chemical Industry     

Preparation and characterization of a proton‐exchange membrane by the radiation grafting of styrene onto polytetrafluoroethylene films

Radiation‐induced simultaneous grafting of styrene onto polytetrafluoroethylene (PTFE) films and the subsequent sulfonation in the chlorosulfonic acid/dichloroethane were investigated. The effects of the main radiation grafting conditions, such as the type of solvents, irradiation dose, dose rate, the styrene concentrations, etc., on the degree of grafting (DOG) were studied. To elucidate the influence of both the grafting and sulfonation conditions on the properties of the PTFE‐g‐polystyrene‐sulfonic acid (PSSA) membranes, the sulfonation conditions, including the sulfonation temperature and the concentration of the ClSO₃H with respect to the DOG, were systematically evaluated. The grafted and sulfonated membranes were characterized by FTIR–ATR spectra, ion‐exchange capacity (IEC), water uptake, thickness measurement, etc. The as‐prepared PTFE‐g‐PSSA membranes in this work showed a good combination of a high IEC (0.85–2.75 meq g^?1), acceptable water uptake (8.86–56.9 wt %), low thickness, and volume expansion and/or contraction. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 1415–1428, 2006     

Syntheses and adsorption properties for Hg2+ of chelating resin of crosslinked polystyrene‐supported 2,5‐dimercapto‐1,3,4‐thiodiazole

A novel chelating resin with functional group containing S and N atoms was prepared using chloromethylated polystyrene and 2,5‐dimercapto‐1,3,4‐thiodiazole (also called bismuththiol I, BMT) as materials. Its structure was characterized by infrared spectra and elementary analysis. The results showed that the content of the functional group was 2.07 mmol BMT g^?1 resin, 47% of which were in the form of monosubstitution (PS‐BMT‐1) and 53% in the form of double substitution (PS‐BMT‐2). The adsorption for mercury ion was investigated. The adsorption dynamics showed that the adsorption was controlled by liquid film diffusion. Increasing the temperature was beneficial to adsorption. The Langmuir model was much better than the Freundlich model to describe the isothermal process. The adsorption activation energy (E_a), ΔG, ΔH, and ΔS values calculated were 18.56 kJ·mol^?1, ‐5.99 kJ·mol^?1, 16.38 kJ·mol^?1, and 37.36, J·mol^?1·K^?1, respectively. The chelating resin could be easily regenerated by 2% thiourea in 0.1 mol·L^?1 HCl with higher effectiveness. Five adsorption–desorption cycles demonstrated that this resin was suitable for repeated use without considerable change in adsorption capacity. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 1646–1652, 2004     

Synthesis,physical properties,and crystallization of optically active poly(L‐phenyllactic acid) and poly(L‐phenyllactic acid‐co‐L‐lactic acid)

Optically active poly(L ‐phenyllactic acid) (Ph‐PLLA), poly(L ‐lactic acid) (PLLA), and poly(L ‐phenyllactic acid‐co‐L ‐lactic acid) with weight‐average molecular weight exceeding 6 × 10³ g mol^?1 were successfully synthesized by acid catalyzed direct polycondensation of L ‐phenyllactic acid and/or L ‐lactic acid in the presence of 2.5–10 wt % of p‐toluenesulfonic acid. Their physical properties and crystallization behavior were investigated by differential scanning calorimetry, thermogravimetry, and polarimetry. The absolute value of specific optical rotation ([α]) for Ph‐PLLA (?38 deg dm^?1 g^?1 cm³) was much lower than that of [α] for PLLA (?150 deg dm^?1 g^?1 cm³), suggesting that the helical nature was reduced by incorporation of bulky phenyl group. PLLA was crystallizable during solvent evaporation, heating from room temperature, and cooling from the melt. Incorporation of a very low content of bulky phenyllactyl units even at 4 mol % suppressed the crystallization of L ‐lactyl unit sequences during heating and cooling, though the copolymers were crystallizable for L ‐phenylactyl units up to 6 mol % during solvent evaporation. The activation energy of thermal degradation (ΔE_td) for Ph‐PLLA (200 kJ mol^?1) was higher than that for PLLA (158 kJ mol^?1). The ΔE_td for the copolymers increased with an increase in L ‐phenyllactyl unit content. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Copolymerization of butadiene with styrene using a rare‐earth metal compound – dialkylmagnesium – halohydrocarbon catalytic system

Copolymerizations of butadiene (Bd) with styrene (St) were carried out with catalytic systems composed of a rare‐earth compound, Mg(n‐Bu)₂ (di‐n‐butyl magnesium) and halohydrocarbon. Of all the rare earth catalysts examined, Nd(P₅₀₇)₃–Mg(n‐Bu)₂–CHCl₃ showed a high activity in the copolymerization under certain conditions: [Bd] = [St] = 1.8 mol l^?1, [Nd] = 6.0 × 10^?3 mol l^?1, Mg/Nd = 10, Cl/Nd = 10 (molar ratio), ageing for 2 h, copolymerization at 50 °C for 6–20 h. The copolymer of butadiene and styrene obtained has a relatively high styrene content (10–30 mol%), cis‐1,4 content in butadiene unit (85–90%), and molecular weight ([η] = 0.8–1 dL g^?1). Monomer reactivity ratios were estimated to be r_Bd = 36 and r_St = 0.36 in the copolymerization. © 2002 Society of Chemical Industry     

Sorption capacity of a new generation granular activated carbon—Bio‐Sep® bead—and its use in a suspended growth bioreactor

BACKGROUND: A new generation granular activated carbon—Bio‐Sep® beads—consist of 25% polymer (Nomex) and 75% powdered activated carbon. The porous structure and high surface area of these beads make them suitable for sorbent in adsorption columns, and for immobilization media in bioreactors. The aim of this study was to study the sorption characteristics of Bio‐Sep® beads for methyl t‐butyl ether (MTBE) and t‐butyl alcohol (TBA), and to demonstrate the advantage of their usage in a suspended growth bioreactor. RESULTS: The maximum uptake capacity of Bio‐Sep® beads for MTBE and TBA, in the studied concentration range (10–100 mg L^?1), was observed to be 9.73 and 6.23 mg g^?1, respectively. A 52 h desorption experiment resulted in 13.6–42.2% MTBE and 33–53% TBA desorption corresponding to the initial solid phase concentrations of 1.68–9.73 mg g^?1 and 1.41–6.23 mg g^?1, respectively. The sorption of TBA on the Bio‐Sep® beads was significantly hindered by the presence of MTBE. The addition of 10 g Bio‐Sep® beads (dry weight) in a suspended growth bioreactor was able to eliminate the inhibitory effect of 150 mg L^?1 MTBE. CONCLUSIONS: At an equilibrium aqueous phase concentration (C_e) of 1 mg L^?1, the solid phase concentration (q_e) on Bio‐Sep® beads were observed as 1.44 and 0.47 mg g^?1 for MTBE and TBA, respectively. The results obtained in this study indicate that Bio‐Sep® beads have reasonable sorption and desorption characteristics, which can be successfully exploited for the removal/degradation of toxic organic pollutants in high rate bioreactors. Copyright © 2007 Society of Chemical Industry     

Specific energy dissipation rate for super‐high‐rate anaerobic bioreactor

BACKGROUND: Specific energy dissipation rate (?) is an important performance parameter of the super‐high‐rate anaerobic bioreactor (SAB) and is closely linked with power matching and operation optimization. The ? value was investigated for a SAB using anaerobic granular sludge and simulating gas production. The ? models for separation, reaction and water distribution units were established. RESULTS: Experimental results showed that the model predictions agreed well with the experimental data and, thus, they may be used for power matching and operation optimization of similar high‐rate anaerobic bioreactors. The ? value for the separation unit was so low as to be neglected. The maximum ? values for the reaction unit during nonfluidization, granular sludge agglomeration, liquid‐solid two‐phase fluidization and gas‐liquid‐solid three‐phase fluidization states were 0.143 W m^?3, 4.449 W m^?3, 2.173 W m^?3 and 11.132 W m^?3, respectively. The maximum ? value for the water distribution unit was 8.37 W m^?3. ? for the reaction unit was significantly influenced by ρ_p, u_l and V_p, u_g and d_p. CONCLUSION: The maximum ? value of 11.132 W m^?3 was the basic parameter for power matching for the SAB. Some measures were introduced to reduce the ? values based on parametric sensitivity analyses. The present investigation will further assist in optimizing the operation and design of SABs. Copyright © 2011 Society of Chemical Industry     

Crosslinked hydroxyl‐conductive copolymer/silica composite membranes based on addition‐type polynorbornene for alkaline anion exchange membrane fuel cell applications

Crosslinked hydroxyl‐conductive copolymer/silica composite membranes based on addition‐type polynorbornene, poly(dodoxymethylene norbornene‐co‐norbornene‐3‐(trimethylpropyl ammonium)‐functionalized silica (QP(DNB/NB‐SiO₂), were prepared by a sol–gel method. Copolymer composite membranes with different degree of quaternary ammonium functional silica, designated as QP(DNB/NB‐SiO₂‐X) (X = 5, 10, 15 and 25 wt%, respectively), displayed good dimensional stabilities with low in‐plane swelling rate of 1.32–3.7%, good mechanical properties with high elastic modulus of 605.4–756.8 MPa and high tensile strength of 13.2–20 Mpa. The achieved copolymer composite membranes could self‐assemble into a microphase‐separated morphology with randomly oriented long‐range aliphatic chain/cylinder ionic channels that were imbedded in the hydrophobic PNB matrix. Among these membranes, the QP(DNB/NB‐SiO₂‐25) showed the parameter with ionic conductivity of 9.33 × 10^?3S cm^?1, methanol permeability of 2.89 × 10^?7cm² s^?1, and ion‐exchange capacity(IEC) of 1.19 × 10^?3 mol g^?1. A current density of 82.3mA cm^?2, the open circuit voltage of 0.65 V and a peek power density of 32 mW cm^?2 were obtained. POLYM. ENG. SCI., 58:13–21, 2018. © 2017 Society of Plastics Engineers     

A redox‐mediator‐doped gel polymer electrolyte applied in quasi‐solid‐state supercapacitors

Methylene blue (MB) redox mediator was introduced into polyvinyl alcohol/polyvinyl pyrrolidone (PVA/PVP) blend host to prepare a gel polymer electrolyte (PVA‐PVP‐H₂SO₄‐MB) for a quasi‐solid‐state supercapacitor. The electrochemical properties of the supercapacitor with the prepared gel polymer electrolyte were evaluated by cyclic voltammetry, galvanostatic charge–discharge, electrochemical impedance spectroscopy, and self‐discharge measurements. With the addition of MB mediator, the ionic conductivity of gel polymer electrolyte increased by 56% up to 36.3 mS·cm^?1, and the series resistance reduced, because of the more efficient ionic conduction and higher charge transfer rate, respectively. The electrode specific capacitance of the supercapacitor with PVA‐PVP‐H₂SO₄‐MB electrolyte is 328 F·g^?1, increasing by 164% compared to that of MB‐undoped system at the same current density of 1 A·g^?1. Meanwhile, the energy density of the supercapacitor increases from 3.2 to 10.3 Wh·kg^?1. The quasi‐solid‐state supercapacitor showed excellent cyclability over 2000 charge/discharge cycles. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39784.     

Molecularly imprinted polymer microspheres derived from pickering emulsions polymerization in determination of di(2‐ethylhexyl) phthalate in bottled water samples

The mono‐dispersed macroporous Molecularly Imprinted microspheres (MIPMs) selective for Diethylhexyl Phthalate (DEHP) were synthesized by Pickering emulsion polymerization. Silica nanoparticles were stabilizers in forming a stable oil‐in‐water emulsion, while the polymeric system was prepared by radical polymerization using methacrylic acid as functional monomer and ethylene glycol dimethacrylate as cross‐linker. The results of scanning electron microscopy and nitrogen adsorption desorption measurement indicated that the obtained polymer microspheres had regularly porous structure and narrowly diameter distribution (100 nm), besides the specific surface area (S_BET) was 452 m² g^?1, pore volume was 9.685 cm³ g^?1, and pore diameter was 5.089 nm. The equilibrium adsorption capacity of MIPs was 1.75 mg g^?1 at 298 K. Good selectivity for DEHP in another two kinds of analogies (DBP and DAP) was demonstrated with high selectivity coefficients, respectively 17.753 and 19.450. In the end, DEHP‐MIP was used as packing of solid‐phase extraction to form an sensitive analytical method in extraction and enrichment DEHP in bottled water samples with the limits of detection of 1.7–2.5 μg L^?1.The recoveries at three spiking level (0.05, 0.1, and 1 mg L^?1) were varied between at 97.5 and 103.1% with RSD values below 3.5. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43484.     

Comparison of rigid divinylbenzene with flexible 1,7‐octadiene crosslinks in acrylic acid resins—effects on kinetics of swelling and loading of heavy metal ions from water

Acrylic acid–1,7‐octadiene resin was synthesized in beaded form by a two‐step process: suspension polymerization of ethylacrylate and 1,7‐octadiene monomers, followed by hydrolysis using either 98% H₂SO₄ or 10 M NaOH. Acrylic acid–divinylbenzene resins were also synthesized by the same process for the purpose of comparing a rigid divinylbenzene with a flexible 1,7‐octadiene crosslinkage in the acrylic acid resins. Swelling of the resins in distilled water shows that replacing divinylbenzenes with 1,7‐octadiene makes the resin achieve greater swelling in a significantly shorter time. 1,7‐Octadiene also allowed for an increase in crosslinkage to 20% compared to 4% in the case of divinylbenzene, without compromising the loading rates of toxic heavy metal ions like Pb²⁺, Cu²⁺, and Cr³⁺ from water samples. The acrylic acid–1,7‐octadine resin was found useful for removal of the toxic heavy metal ions from wastewater samples. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 41038.     

Improved stability in P3HT:PCBM photovoltaics by incorporation of well‐designed polythiophene/graphene compositions

Morphological and photovoltaic stabilities of poly(3‐hexylthiophene) (P3HT):phenyl‐C₆₁‐butyric acid methyl ester (PC₇₁BM) solar cells were investigated in pristine and modified states. To this end, four types of patterned/assembled nanostructures, namely reduced graphene oxide (rGO)‐g‐poly(3‐dodecylthiophene)/P3HT patched‐like pattern, rGO–polythiophene/P3HT/PC₇₁BM nanofiber, rGO‐g‐P3HT/P3HT cake‐like pattern and supra(polyaniline (PANI)‐g‐rGO/P3HT), were designed on the basis of rGO and various conjugated polymers. Intermediately covered rGO nanosheets by P3HT crystals (supra(PANI‐g‐rGO/P3HT)) performed better than sparsely (patched‐like pattern) and fully (cake‐like pattern) covered ones in P3HT:PC₇₁BM solar cell systems. Supra(PANI‐g‐rGO/P3HT) nanohybrids largely phase‐separated in active layers (root mean square = 0.88 nm) and also led to the highest performance (power conversion efficiency of 5.74%). The photovoltaic characteristics demonstrated decreasing trends during air aging for all devices, but with distinct slopes. The steepest decreasing plots were obtained for the unmodified P3HT:PC₇₁BM devices (from 1.77% to 0.28%). The two supramolecules with the most ordered structures, that is, cake‐like pattern (10.12 mA cm^?2, 51%, 0.58 V, 2.2 × 10^?6 cm² V^?1 s^?1, 4.3 × 10^?5 cm² V^?1 s^?1, 0.69 nm and 2.99%) and supra(PANI‐g‐rGO/P3HT) (12.51 mA cm^?2, 57%, 0.63 V, 1.2 × 10^?5 cm² V^?1 s^?1, 3.4 × 10^?4 cm² V^?1 s^?1, 0.82 nm and 4.49%), strongly retained morphological and photovoltaic stabilities in P3HT:PC₇₁BM devices after 1 month of air aging. According to the morphological, optical, photovoltaic and electrochemical results, the supra(PANI‐g‐rGO/P3HT) nanohybrid was the best candidate for stabilizing P3HT:PC₇₁BM solar cells. © 2020 Society of Chemical Industry     

Lipase‐catalyzed esterification of cinnamic acid and oleyl alcohol in organic solvent media

The esterification of cinnamic acid (CA) and oleyl alcohol (OA) in organic solvent media by immobilized lipase Novozym 435 was optimized in terms of selected parameters, including the logarithm of the 1‐octanol/water partition coefficient of the organic solvent (log P, 0.29–4.5), initial water activity (a_w, 0.05–0.75), agitation speed (0–200 rpm), temperature (35–65 °C) and ratio of substrates (CA/OA, 1.0:0.5–1.0:6.0). The results showed that the more hydrophobic solvent mixtures and lower initial a_w values resulted in a higher enzymatic activity and bioconversion yield. The most appropriate solvent medium and initial a_w value was the mixture of iso‐octane/2‐butanone (85:15, v/v) and 0.05, respectively. The results also showed that an agitation speed of 150 rpm and a reaction temperature of 55 °C were optimal for the reaction system. The activation energy (E_a) of the esterification reaction was calculated as 43.6 kJ mol^?1. The optimal ratio of CA to OA was 1.0:6.0, with the absence of any inhibition by OA. Using the optimized conditions, the maximum enzymatic activity was 390.3 nmol g^?1 min^?1, with a bioconversion yield of 100% after 12 days of reaction. In addition, the electrospray ionization‐mass spectroscopy analysis confirmed that the major end product of the esterification reaction was oleyl cinnamate. Copyright © 2005 Society of Chemical Industry     

Synthesis and properties of poly(sodium acrylate‐co‐2‐acryloylamino‐2‐methyl‐1‐propanesulfonic acid)/attapulgite as a salt‐resistant superabsorbent composite

A novel salt‐resistant superabsorbent composite was prepared by copolymerization of partially neutralized acrylic acid, 2‐acryloylamino‐2‐methyl‐1‐propanesulfonic acid (AMPS) and attapulgite (APT). To enhance the swelling rate (SR) of the copolymer, sodium bicarbonate was used as a foaming agent in the course of copolymerization. Furthermore, for improving the properties of swollen hydrogel, such as strength, resilience and dispersion, the copolymer was surface‐crosslinked with glycerine and sodium silicate, and then the surface‐crosslinked copolymer was blended with aluminum sulfate and sodium carbonate in post treatment process. The influences of some reaction conditions, such as amount of AMPS, APT, and initiator, and neutralization degree of acrylic acid on water absorbency in 0.9 wt% NaCl aqueous solution both under atmospheric pressure (WA) and load (WA_P, P ≈ 2 × 10³ Pa) were investigated. In addition, the effect of them on SR was also studied. The WA and WA_P of the superabsorbent composite prepared under optimal conditions in 0.9 wt% NaCl aqueous solution were 52 g·g^?1 and 8 g·g^?1, respectively. Besides, the SR was fast, and it could reach 0.393 mL·(g·s)^?1. Moreover, the swollen hydrogel possessed excellent salt resistance, hydrogel resilience and dispersion. POLYM. ENG. SCI., 2009. © 2008 Society of Plastics Engineers     

Polystyrene composites of single‐walled carbon nanotubes‐graft‐polystyrene

Single‐walled carbon nanotubes (SWCNTs) dispersed in N‐methylpyrrolidone (NMP) were functionalized by addition of polystyryl radicals from 2,2,6,6‐tetramethyl‐1‐piperidinyloxy‐ended polystyrene (SWCNT‐g‐PS). The amount of polystyrene grafted to the nanotubes was in the range 20‐25 wt% irrespective of polystyrene number‐average molecular weight ranging from 2270 to 49 500 g mol^?1. In Raman spectra the ratios of D‐band to G‐band intensity were similar for all of the polystyrene‐grafted samples and for the starting SWCNTs. Numerous near‐infrared electronic transitions of the SWCNTs were retained after polymer grafting. Transmission electron microscopy images showed bundles of SWCNT‐g‐PS of various diameters with some of the polystyrene clumped on the bundle surfaces. Composites of SWCNT‐g‐PS in a commercial‐grade polystyrene were prepared by precipitation of mixtures of the components from NMP into water, i.e. the coagulation method of preparation. Electrical conductivities of the composites were about 10^?15 S cm^?1 and showed no percolation threshold with increasing SWCNT content. The glass transition temperature (T_g) of the composites increased at low filler loadings and remained constant with further nanotube addition irrespective of the length and number of grafted polystyrene chains. The change of heat capacity (ΔC_p) at T_g decreased with increasing amount of SWCNT‐g‐PS of 2850 g mol^?1, but ΔC_p changed very little with the amount of SWCNT‐g‐PS of higher molecular weight. The expected monotonic decrease in ΔC_p coupled with the plateau behavior of T_g suggests there is a limit to the amount that T_g of the matrix polymer can increase with increasing amount of nanotube filler. Copyright © 2012 Society of Chemical Industry