Proton exchange composite membranes from blends of brominated and sulfonated poly(2,6‐dimethyl‐1,4‐phenylene oxide)

New composite proton exchange membrane was prepared by mixing a 1‐methyl‐2‐pyrrolidone (NMP) solution of sulfonated poly(2,6‐dimethyl‐1,4‐phenylene oxide) (SPPO) in sodium form and brominated poly(2,6‐dimethyl‐1,4‐phenylene oxide) (BPPO) for hydrophilic‐hydrophobic balance, then casting the solution as a thin film, evaporating the solvent, and treating the membrane with aqueous hydrochloric acid. The resulting membranes were subsequently characterized using FTIR‐ATR, SEM‐EDXA, and TGA instrumentation as well as measurements of basic properties such as ion exchange capacity (IEC), water uptake, proton conductivity, methanol permeability, and single cell performance. Water uptake, IEC, proton conductivity, and methanol permeability all increased with a corresponding increase of SPPO content. By properly compromising the conductivity and methanol permeability, membranes with 60–80 wt % SPPO content exhibited comparable proton conductivity to that of Nafion^® 117, with only half the methanol permeability, thereby demonstrating higher single cell performance. The membranes developed in this study could thus be a suitable candidate electrolyte for proton exchange membrane fuel cells (PEMFCs). © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Methanol permeability and proton conductivity of polybenzimidazole and sulfonated polybenzimidazole

The preparation of sulfonated polybenzimidazole (sPBI) by the grafting of (4‐bromomethyl) benzenesulfonate onto polybenzimidazole (PBI) has been investigated. The methanol permeability and proton conductivity of PBI and sPBI have been studied, and the effects of methanol concentration and temperature on the methanol permeability of PBI and sPBI membranes are discussed. The results showed that the PBI membrane is a good methanol barrier. Methanol permeability in this membrane decreases with increasing methanol concentration and increases with increasing temperature. The temperature‐dependence of methanol permeability of PBI and sPBI membranes is of the ‘Arrhenius type’. Methanol permeation of sPBI is less sensitive to temperature than that of PBI. However, sPBI is a poorer methanol barrier when compared to PBI. Methanol permeability in sPBI membranes increases with increasing methanol concentration and temperature. The proton conductivity of sPBI is 4.69 × 10^?4 S cm^?1 at room temperature in the hydrated state. The DC conductivity of sPBI–H₃PO₄ increases with increasing temperature. Proton transport in sPBI–H₃PO₄ is less sensitive to temperature than that in PBI–H₃PO₄. Copyright © 2004 Society of Chemical Industry     

Behavior of sulfonated poly(ether ether ketone) in ethanol–water systems

The behavior of sulfonated poly(ether ether ketone) (sPEEK) membranes in ethanol–water systems was studied for possible application in direct ethanol fuel cells (DEFCs). Polymer membranes with different degrees of sulfonation were tested by means of uptake, swelling, and ethanol transport with dynamic measurements (liquid–liquid and liquid–gas systems). Ethanol permeability was determined in an liquid–liquid diffusion cell. For membranes with an ion‐exchange capacity (IEC) between 1.15 and 1.75 mmol/g, the ethanol permeability varied between 5 × 10^?8 and 1 × 10^?6 cm²/s, being dependent on the measuring temperature. Ethanol and water transport in liquid–gas systems was tested with pervaporation as a function of IEC and temperature. Higher IEC accounted for higher fluxes and lower water/ethanol selectivity. The temperature had a large effect on the fluxes, but the selectivity remained constant. Furthermore, the membranes were characterized with proton conductivity measurements. The proton diffusion coefficient was calculated, and a transition in the proton transfer mechanism was found at a water number of 12. Membranes with high IEC (>1.6 mmol/g) exhibited larger proton diffusion coefficients in ethanol–water systems than in water systems. The membrane with the lowest IEC exhibited the best proton transport to ethanol permeability selectivity. The use of sPEEK membranes in DEFC systems depends on possible modifications to stabilize the membranes in the higher conductive region rather than on modifications to increase the proton conductivity in the stable region. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Cross‐linked Poly(arylene ether ketone) Proton Exchange Membranes with High Ion Exchange Capacity for Fuel Cells

Sulfonated poly(arylene ether ketone) (SPAEK) possessing the pendant carboxylic acid groups was synthesized. The carboxylic acid groups of SPAEK were reacted with a cross‐linking reagent to prepare a cross‐linked membrane with a high ion exchange capacity (IEC), a high oxidative stability, and an excellent mechanical strength. The cross‐linking hindered the mobility of the polymer chains and thus strongly affected the water uptake and the methanol permeability of the membranes. Also, as the cross‐linker used in this study bore sulfonic acid groups, cross‐linking did not lead to a noticeable loss of the proton conductivity. The cross‐linked SPAEK membrane with 20% cross‐linking density, CSPAEK‐20% membrane, exhibited a high proton conductivity of 0.045 S cm^–1 associated with a high IEC value of 1.78 mmol g^–1 but a low methanol permeability of 4.3 × 10^–7 cm² s^–1. The CSPAEK‐20% membrane also showed excellent cell performance and oxidation resistance.     

Sulfonated poly(bis‐A)‐sulfones as proton exchange membranes for direct methanol fuel cell application

Sulfonated poly(bis‐A)‐sulfone (SPSF) samples were prepared by a mild postsulfonation method using trimethylsilyl chlorosulfonate as sulfonation agent, and their thermal and mechanical properties were evaluated. The serials of SPSF membranes are thermally stable up to 450°C in air. When compared with the poly(bis‐A)‐sulfone membrane, the hydrophilicity and water uptake of the SPSF membranes are enhanced. A microphase‐separated structure comprised of hydrophilic and hydrophobic polymer backbone was observed from atomic force microscopy phase images. The hydrophilic ionic clusters become continuous to form channels when ion exchange capacity (IEC) reached 1.47 mequiv/g. Moreover, the membranes showed very good proton conductivities (20°C, 0.01–0.11 S/cm) and low‐methanol permeability (0.09–3.06 × 10^?6 cm²/s), and the methanol diffusion coefficients were lower than that of Nafion112 (1.35 × 10^?6 cm²/s) with IEC values from 0.70 to 1.47 mequiv/g. However, the Fenton's reagent test revealed that the membranes exhibited very poor oxidation stability, which is the main defect limiting the application of SPSF for proton exchange membranes. POLYM. ENG. SCI., 2011. © 2010 Society of Plastics Engineers     

Synthesis and properties of sulfonated poly(phosphazene)‐graft‐poly(styrene‐co‐N‐benzylmaleimide) copolymers via atom transfer radical polymerization for proton exchange membrane

A series of sulfonated poly(phosphazene)‐graft‐poly(styrene‐co‐N‐benzylmaleimide) (PP‐g‐PSN) copolymers were prepared via atom transfer radical polymerization (ATRP), followed by regioselective sulfonation which occurred preferentially at the poly(styrene‐co‐N‐benzylmaleimide) sites. The structures of these copolymers were confirmed by Fourier transform infrared (FTIR) spectroscopy, ¹H‐NMR, and ³¹P‐NMR, respectively. The resulting sulfonated PP‐g‐PSN membranes showed high water uptakes (WUs), low water swelling ratios (SWs), low methanol permeability coefficients, and proper proton conductivities. In comparison with non‐grafting sulfonated poly(bis(phenoxy)phosphazene) (SPBPP) membrane previously reported, the present membranes displayed higher proton conductivity, significantly improved the thermal and oxidative stabilities. Transmission electron microscopy (TEM) observation showed clear phase‐separated structures resulting from the difference in polarity between the hydrophobic polyphosphazene backbone and hydrophilic sulfonated poly(styrene‐co‐N‐benzylmaleimide) side chains, indicating effective ionic pathway in these membranes. The results showed that these materials were promising candidate materials for proton exchange membrane (PEM) in direct methanol fuel cell (DMFC) applications. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42251.     

Vinyl‐addition type norbornene copolymer containing sulfonated biphenyl pendant groups for proton exchange membranes

The vinyl addition type copolymer poly(butoxymethylene norbornene‐co‐biphenyl oxyhexamethyleneoxymethylene norbornene) (P(BN/BphN)) was synthesized by using bis‐(β‐ketonaphthylimino)nickel(II)/B(C₆F₅)₃ catalytic system. P(BN/BphN) was sulfonated to give sulfonated P(BN/BphN) (SP(BN/BphN)) with concentrated sulfuric acid (98%) as sulfonating agent in a component solvent. The ion exchange capacity (IEC), degree of sulfonation (DS), water uptake, and methanol permeability of the SP(BN/BphN)s were increased with the sulfonated time. The methanol permeability of the SP(BN/BphN) membranes was in the range of 1.8 × 10^?7 to 7.5 × 10^?7 cm²/s, which were lower than the value 1.3 × 10^?6 cm²/s of Nafion®115. The proton conductivity of SP(BN/BphN) membranes increased with the increase of IEC values, temperature, and water uptake. Water uptake of the SP(BN/BphN) membranes was lower than that of Nafion® 115 and leads to low proton conduction. Microscopic phase separation occurred in SP(BN/BphN) membrane and domains containing sulfonic acid groups were investigated by SEM and TEM. SP(BN/BphN) membranes had good mechanical properties, high thermal stability, and excellent oxidative stability. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Mechanical and chemical properties of poly(styrene‐isobutylene‐styrene) block copolymers: Effect of sulfonation and counter ion substitution

In this study, the mechanical and chemical properties of a series of sulfonated poly(styrene‐isobutylene‐styrene) (SIBS) block copolymers were evaluated using a combination of nanoindentation, dynamic mechanical analysis (DMA), elemental analysis (EA), Fourier transform infrared spectroscopy (FTIR), water absorption, and small angle X‐ray scattering studies (SAXS). The materials properties were characterized as a function of the sulfonation percent in the block copolymers, as well as a result of the counter‐ion substitution with Mg²⁺, Ca²⁺, and Ba²⁺. Nanoindentation studies revealed that the elastic modulus (E) and hardness (H) increase with sulfonation up to a certain level, at which point, the effect of water content further hinders any mechanical reinforcement. The incorporation of counter‐ions increases E and H, but the results are dependent upon the size of the counter‐ion. DMA results showed that the polymer maintained the glass transition temperature (T_g) of the polyisobutylene (PIB) segment (?60°C) regardless of the sulfonation level or counter‐ion substituted. However, both the shoulder of the PIB T_g (?30°C), which was probably caused by a Rouse‐type motion, as well as the T_g of polystyrene (105°C) disappeared upon sulfonation. Counter‐ion substitution increased the storage modulus of the rubbery plateau, which is indicative of a stronger and more thermally stable crosslinked complex formation. Additional unique relaxations were observed with the counter‐ions, and could be attributed to the stretching/rotation of the S? O bond and the interaction of the cations with the oxygen in the sulfonic group. FTIR results also revealed a unique shifting of the asymmetric S? O band when counter‐ions were added. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40344.     

Effect of block composition on the morphology,hydration, and transport properties of sulfonated PS‐b‐PEGPEM‐b‐PS

This work discusses the effect of block composition on the properties of proton conducting polymer membranes. A homopolymer and two block copolymers were synthesized using atom transfer radical polymerization. The homopolymer poly(ethylene glycol phenyl ether methacrylate) (PEGPEM) was used as a bifunctional macroinitiator. Polystyrene (PS), was added to both sides of PEGPEM (A) with two different percentages of PS (B) (i.e., 18 and 31%). These copolymers, BAB 18, BAB 31 and the homopolymer A, were completely sulfonated (SA, SBAB 18 and SBAB 31). The resulting polymers produced different water absorption values and transport properties for direct methanol fuel cell (DMFC) applications. The nanostructure and morphology of the casted membranes were studied using small‐angle X‐ray scattering and atomic force microscopy. The results revealed that all six membranes exhibited a disordered phase‐segregated morphology, which changed on sulfonation into small‐interconnected ionic domains. Normalized DMFC selectivities (proton conductivity over methanol permeability divided by the respective values for Nafion^®) were calculated and ranged from 1.16 (SBAB 31) to 15.30 (BAB 18), indicating that the performance of these materials can be comparable or better than Nafion^®. Transport property results also suggest that chemistry (block nature and composition), morphology and water content play a critical role in the transport mechanism of protons and methanol. For example, the percentage of B in BAB 18 provides shorter interstitial ionic distances and sufficient water content to produce high proton conductivity, while maintaining low methanol permeability in a multi‐ionic proton exchange membrane. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 44343.     

Polymer Nanocomposite Membranes of Sulfonated Poly(Styrene‐Isobutylene‐Styrene) With Sulfonated Graphene Oxide for Fuel Cell and Protective Clothing Applications

Graphene oxide (GO) and its sulfonated analog (sGO) have been incorporated into sulfonated poly(styrene‐isobutylene‐styrene) (SO₃H SIBS) in order to enhance its water retention and proton conductivity, while aiming to block permeant passage through the material. The polymer nanocomposite membranes (PNMs) were tested for two applications: direct methanol fuel cell and chemical and biological protective clothing. The transport properties of the membranes were determined as a function of SIBS sulfonation level (i.e., 37, 61, and 88 mol%), filler type (i.e., GO and sGO) and filler loading (i.e., 1, 3, 5, and 10 wt%). Fourier transform infrared spectroscopy (FTIR) and thermogravimetric analysis (TGA) confirmed the functionalization and incorporation of the fillers into SO₃H SIBS. No significant changes were observed in the thermal stability or FTIR spectra of the PNMs after addition of the fillers. Dissimilar behaviors were observed for the ion exchange capacity, water absorption capabilities and transport properties of the membranes after incorporation of the fillers. Atomic force microscopy (AFM) phase images and Fenton's test results indicate that the oxidative stability of the PNMs is associated to the interconnectivity between the hydrophilic domains of the fillers and SO₃H SIBS. The PNMs presented low permeability and high proton conductivity and thus, functioned adequately for both applications. POLYM. ENG. SCI., 59:E455–E467, 2019. © 2018 Society of Plastics Engineers     

Novel membranes based on poly(5‐(methacrylamido)tetrazole) and sulfonated polysulfone for proton exchange membrane fuel cells

Proton‐exchange membrane fuel cells (PEMFC)s are increasingly regarded as promising environmentally benign power sources. Heterocyclic molecules are commonly used in the proton conducting membranes as dopant or polymer side group due to their high proton transfer ability. In this study, 5‐(methacrylamido)tetrazole monomer, prepared by the reaction of methacryloyl chloride with 5‐aminotetrazole, was polymerized via conventional free radical mechanism to achieve poly(5‐(methacrylamido)tetrazole) homopolymer. Novel composite membranes, SPSU‐PMTetX, were successfully produced by incorporating sulfonated polysulfone (SPSU) into poly(5‐(methacrylamido)tetrazole) (PMTet). The sulfonation of polysulfone was performed with trimethylsilyl chlorosulfonate and high degree of sulfonation (140%) was obtained. The homopolymers and composite membranes have been characterized by NMR, FTIR, thermogravimetric analysis (TGA), and differential scanning calorimetry (DSC). ¹H‐NMR and FTIR confirmed the sulfonation of PSU and the ionic interaction between sulfonic acid and poly(5‐(methacrylamido)tetrazole) units. TGA showed that the polymer electrolyte membranes are thermally stable up to ～190°C. Scanning electron microscopy analysis indicated the homogeneity of the membranes. This result was also supported by the appearance of a single T_g in the DSC curves of the blends. Water uptake and proton conductivity measurements were, as well, carried out. Methanol permeability measurements showed that the composite membranes have similar methanol permeability values with Nafion 112. The maximum proton conductivity of anhydrous SPSU‐PMTet0.5 at 150°C was determined as 2.2 × 10^?6 S cm^?1 while in humidified conditions at 20°C a value of 6 × 10^?3 S cm^?1 was found for SPSU‐PMTet2. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40107.     

Montmorillonite‐reinforced sulfonated poly(phthalazinone ether sulfone ketone) nanocomposite proton exchange membranes for direct methanol fuel cells

To produce a composite membrane with high conductivity and low permeability, SPPESK with a degree of sulfonation of 101% was carefully selected for the preparation of montmorillonite (MMT)‐reinforced SPPESK using solution intercalation. The fundamental characteristics such as water uptake, swelling ratio, proton conductivity, methanol permeability, and mechanical properties of the composite membranes were studied. Water uptake is improved when organic MMT (OMMT) loading increase. The composite membranes with CTAB‐MMT loading of 4–0.5% show 0.143–0.150 S cm^?1 proton conductivity at 80°C, which approaches the value of Nafion112. In addition, methanol permeability was decreased to 6.29 × 10^?8 cm² s^?1 by the addition of 6 wt % OMMT. As a result, the SPPESK‐MMT composite membrane is a good candidate for use in direct methanol fuel cells. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39852.     

Synthesis and characterization of poly(vinyl alcohol)‐based membranes for direct methanol fuel cell

Membranes made of poly(vinyl alcohol) (PVA) and its ionic blends with sodium alginate (SA) and chitosan were synthesized and characterized for their ion-exchange capacity (IEC) and swelling index values to investigate their applicability in direct methanol fuel cells (DMFCs). These membranes were assessed for their intermolecular interactions, thermal stabilities, and mechanical strengths with Fourier transform infrared spectroscopy, X-ray diffraction methods, differential scanning calorimetry, thermogravimetric analysis, and tensile testing, respectively. Methanol permeability and proton conductivity were also estimated and compared to that of Nafion 117. In addition to being effective methanol barriers, the membranes had a considerably high IEC and thermal and mechanical stabilities. The addition of small amounts of anionic polymer was particularly instrumental in the significant reduction of methanol permeability from 8.1 × 10⁻⁸ cm²/s for PVA to 6.9 × 10⁻⁸ cm²/s for the PVA–SA blend, which rendered the blend more suitable for a DMFC. Low methanol permeability, excellent physicomechanical properties, and above all, cost effectiveness could make the use of these blends in DMFCs quite attractive. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 95: 1154–1163, 2005     

Imidazolium ionic liquid incorporation on sulfonated poly(styrene‐isobutylene‐styrene) proton exchange membranes

Ionic liquids (ILs) with different anions and cations were incorporated in sulfonated poly(styrene‐isobutylene‐styrene) (SIBS) to modify its chemical, morphological, and transport properties for direct methanol fuel cell (DMFC) applications. Different loadings of IL and different solvents were studied to have a better understanding of the incorporation process and the ability of the solvent to affect the interaction of the IL with the sulfonated polymer. Morphological characterization with SAXS and AFM suggested changes caused by the incorporation of the IL and by the solvent used. FT‐IR spectra showed small variations in energy related to interactions of the IL with the sulfonic groups which caused thermogravimetric stabilization of the ionic domains. Other results suggest that water has a very significant effect on the morphology, interaction with the IL, and transport properties of the membranes. Optimal concentration of IL (～10 mol %) provides enough water to produce efficient proton conductivity (0.15 S/cm) and minimal methanol permeability (0.8 × 10^?6 cm²/s). © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134 , 44900.     

Preparation and characterization of a proton‐exchange membrane by the radiation grafting of styrene onto polytetrafluoroethylene films

Radiation‐induced simultaneous grafting of styrene onto polytetrafluoroethylene (PTFE) films and the subsequent sulfonation in the chlorosulfonic acid/dichloroethane were investigated. The effects of the main radiation grafting conditions, such as the type of solvents, irradiation dose, dose rate, the styrene concentrations, etc., on the degree of grafting (DOG) were studied. To elucidate the influence of both the grafting and sulfonation conditions on the properties of the PTFE‐g‐polystyrene‐sulfonic acid (PSSA) membranes, the sulfonation conditions, including the sulfonation temperature and the concentration of the ClSO₃H with respect to the DOG, were systematically evaluated. The grafted and sulfonated membranes were characterized by FTIR–ATR spectra, ion‐exchange capacity (IEC), water uptake, thickness measurement, etc. The as‐prepared PTFE‐g‐PSSA membranes in this work showed a good combination of a high IEC (0.85–2.75 meq g^?1), acceptable water uptake (8.86–56.9 wt %), low thickness, and volume expansion and/or contraction. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 1415–1428, 2006     

Preparation and characterization of novel grafted cellophane‐phosphoric acid‐doped membranes for proton exchange membrane fuel‐cell applications

This work concerns preparation of acid‐base polyelectrolyte membranes for fuel‐cell applications from cellulosic backbones for the first time. Grafted cellophane‐phosphoric acid‐doped membranes for direct oxidation methanol fuel cells (DMFC) were prepared following three steps. The first two steps were conducted to have the basic polymers. The first step was introducing of epoxy groups to its chemical structure through grafting process with poly(glycidylmethacrylate) (PGMA). The second step was converting the introduced epoxy groups to imides groups followed by phosphoric acid (? PO₃H) doping as the last step. This step significantly contributes to induce ion exchange capacity (IEC) and ionic conductivity (IC). Chemical changes of the cellophane composition and morphology characters were followed using FTIR, TGA, and SEM analysis. Different factors affecting the membranes characters especially IEC, methanol permeability, and thermal stability were investigated and optimized to have the best preparation conditions. Compared to Nafion 117 membrane, cellophane‐modified membranes show a better IEC, less methanol permeability, and better mechanical and thermal stability. IEC in the range of 1–2.3 meq/g compared to 0.9 meq/g per Nafion was obtained, and methanol permeability has been reduced by one‐order magnitude. However, the maximum obtained IC for cellophane‐PGMA‐grafted membrane doped with phosphoric acid was found 2.33 × 10^?3 (S cm^?1) compared to 3.88 × 10^?2 (S cm^?1) for Nafion 117. The obtained results are very promising for conducting further investigations taking into consideration the very low price of cellophane compared to Nafion. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Highly methanol resistant and selective ternary blend membrane composed of sulfonated PVdF‐co‐HFP,sulfonated polyaniline and nafion

Partially sulfonated poly(vinylidene fluoride‐co‐hexafluoro propylene)/partially sulfonated polyaniline (SPVdF‐co‐HFP/SPAni) binary blend membranes have shown promising results in terms of low methanol permeability and high membrane selectivity compared to Nafion‐117 membrane. However, the proton conductivity and IEC of this binary blend membrane was much lower than Nafion‐117. It was found that incorporation of minimal quantity of Nafion within SPVdF‐co‐HFP/SPAni blend membrane at a constituent weight % ratio of SPVdF‐co‐HFP:SPAni:Nafion = 50:40:10 induced significant improvements in ion‐exchange capacity (IEC), proton conductivity and tensile strength over that of the binary blend membrane. In addition, the SPVdF‐co‐HFP/SPAni/Nafion ternary blend membrane exhibited much lower methanol permeability, higher membrane and relative selectivities and comparable IEC to Nafion‐117. In effect, presence of minimal quantity of Nafion induced significant positive attributes to the ternary blend membrane; and assisted in reaching a balance between material cost and properties. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43294.     

Fluorenyl‐containing Quaternary Ammonium Poly(arylene ether sulfone)s for Anion Exchange Membrane Applications

A series of anion exchange membranes (AEM) based on block quaternary ammonium poly(arylene ether sulfone) (QA‐bPAES) were successfully synthesized from 9,9′‐bis(4‐hydroxyphenyl) fluorene, 4,4′‐(hexafluoroisopropylidene) diphenol and 4,4′‐difluorodiphenyl sulfone via block polymerization, chloromethylation, quaternization, alkalization and solution casting. Properties of the obtained QA‐bPAES membranes, including ion exchange capacity (IEC), water uptake, swelling ratios, methanol permeability and ion conductivity were investigated. The obtained QA‐bPAES membranes showed low water uptakes, high ion conductivities and good physical and chemical stability. For example, the membrane of QA‐bPAES(20/10)‐1.34 with IEC of 1.34 mmol g⁻¹ exhibited swelling ratios of 5.0% and 5.1% in in‐plane and through‐plane direction, respectively, and ion conductivity of 15.6 mS cm⁻¹ in water at 60 °C with low methanol permeability of 1.06 × 10⁻⁷ cm² s⁻¹ (25 °C). All the results indicated that this type of block membranes had good potentials for alkaline anion exchange membrane fuel cell applications.     

Proton exchange membranes prepared by simultaneous radiation grafting of styrene onto poly(tetrafluoroethylene‐co‐hexafluoropropylene) films. II. Properties of sulfonated membranes

Proton exchange membranes were prepared by radiation‐induced grafting of styrene onto commercial poly(tetrafluoroethylene‐co‐hexafluoropropylene) films using a simultaneous irradiation technique followed by a sulfonation reaction. The resulting membranes were characterized by measuring their physicochemical properties such as water uptake, ion exchange capacity, hydration number, and proton conductivity as a function of the degree of grafting. The thermal properties (melting and glass transition temperatures) and thermal stability of the membrane were also investigated using differential scanning calorimetry and thermal gravimetric analysis, respectively. Membranes having degrees of grafting of 16% and above showed proton conductivity of the magnitude of 10⁻² Ω⁻¹ cm⁻¹ at room temperature, as well as thermal stability at up to 290°C under an oxygen atmosphere. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 78: 2443–2453, 2000     

Blend membranes based on disulfonated poly(aryl ether ether ketone)s (SPEEK) and poly(amide imide) (PAI) for direct methanol fuel cell usages

Highly disulfonated poly(aryl ether ether ketone)s (SPEEK-70) copolymer was synthesized via direct polymerization to precisely control the degree of sulfonation (D_s = 1.40), which was confirmed and estimated by ¹H NMR. As expected, the proton conductivity of SPEEK-70 membrane is 0.084 S/cm at 25 °C and increases to 0.167 S/cm at 80 °C, surpassing that of Nafion^® 117. However, the relatively high methanol crossover and excessively swelling properties limited its usage in DMFC. Poly(amide imide) was blended with SPEEK-70 to improve the methanol resistance and mechanical properties. These blend membranes were characterized as a function of weight fraction of PAI in terms of ion exchange capacity (IEC), water uptake, water desorption, proton conductivity and methanol permeability in detail. Although the proton conductivities decreased upon the addition of PAI, higher selectivity values defined as the ratio of proton conductivity to methanol permeability were found for the blend membranes. Therefore, the SPEEK/PAI blend membranes are promising for usage in DMFC.