Fabrication and properties of PVDF and PVDF‐HFP microfiltration membranes

Poly(vinylidene fluoride) (PVDF) and poly(vinylidene fluoride)‐co‐hexafluoropropylene (PVDF‐HFP) were used to fabricate porous microfiltration membranes via a thermally induced phase separation (TIPS) method, and dibutyl phthalate (DBP) was used as diluent. The effects of polymer concentration on structure and performance were studied in detail. In addition, the effect of incorporation of hexafluoropropylene (HFP) groups on the membrane was also investigated. The formation mechanism was proposed with the assistance of a phase diagram. The results showed that the incorporation of HFP groups resulted in a lower crystallization temperature (T_c) of the polymer/DBP system. In addition, the porosity, pure water flux, and ink solution flux decreased with increasing polymer concentration. In contrast, the water contact angle, ink rejection ratio, and mechanical properties had an increasing tendency. When the polymer concentration was 30 wt %, the obtained membrane was most suitable for microfiltration. Furthermore, the incorporation of HFP groups improved the properties of the obtained membrane, including better hydrophobicity, mechanical properties, antifouling property, and chemical resistance. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46711.     

Performances of poly(vinylidene fluoride‐co‐hexafluoropropylene) ultrafiltration membranes modified with poly(vinyl pyrrolidone)

The structure and performance of modified poly(vinylidene fluoride‐co‐hexafluoropropylene) (PVdF‐co‐HFP) ultra‐filtration membranes prepared from casting solutions with different concentrations of poly(vinyl pyrrolidone) (PVP) were investigated in this study. Membrane properties were studied in terms of membrane compaction, pure water flux (PWF), water content (WC), membrane hydraulic resistance ( R _m), protein rejection, molecular weight cut‐off (MWCO), average pore size, and porosity. PWF, WC, and thermal stability of the blend membranes increased whereas the crystalline nature and mechanical strength of the blend membranes decreased when PVP additive concentration was increased. The contact angle (CA) decreased as the PVP concentration increased in the casting solution, which indicates that the hydro‐philicity of the surface increased upon addition of PVP. The average pore size and porosity of the PVdF‐co‐HFP membrane increased to 42.82 Å and 25.12%, respectively, when 7.5 wt% PVP was blended in the casting solution. The MWCO increased from 20 to 45 kDa with an increase in PVP concentration from 0 to 7.5 wt%. The protein separation study revealed that the rejection increased as the protein molecular weight increased. The PVdF‐co‐HFP/PVP blended membrane prepared from a 7.5 wt% PVP solution had a maximum flux recovery ratio of 74.3%, which explains its better antifouling properties as compared to the neat PVdF‐co‐HFP membrane. POLYM. ENG. SCI., 55:2482–2492, 2015. © 2015 Society of Plastics Engineers     

Preparation and characterization of poly(vinyl chloride)/polystyrene/poly(ethylene glycol) hollow‐fiber ultrafiltration membranes

Hollow‐fiber ultrafiltration (UF) membranes were prepared from blends of poly(vinyl chloride) (PVC) and polystyrene (PS) with a dry/wet phase inversion method. Poly(ethylene glycol) (PEG) and N,N‐dimethylacetamide were used as the additive and solvent, respectively. The effects of the PEG concentration in the dope solution as an additive on the cross sections and inner and outer surface morphologies, permeability, and separation performance of the hollow fibers were examined. The mean pore size, pore size distribution, and mean roughness of both the inner and outer surfaces of the produced hollow fibers were determined by atomic force microscopy. Also, the mechanical properties of the hollow‐fiber membranes were investigated. UF experiments were conducted with aqueous solutions of poly(vinyl pyrrolidone) (PVP; K‐90, M_w = 360 kDa). From the results, we found that the PVC/PS hollow‐fiber membranes had two layers with a fingerlike structure. These two layers were changed from a wide and long to a thin and short morphology with increasing PEG concentration. A novel and until now undescribed shape of the nodules in the outer surfaces, which was denoted as a sea‐waves shape, was observed. The outer and inner pore sizes both increased with increasing PEG concentration. The water permeation flux of the hollow fibers increased from 104 to 367 L m^?2 h^?1 bar^?1) at higher PEG concentrations. The PVP rejection reached the highest value at a PEG concentration of 4 wt %, whereas at higher values (from 4 to 9 wt %), the rejection decreased. The same trend was found also for the tensile stress at break, Young's modulus, and elongation at break of the hollow fibers. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 989‐1004, 2013     

Electrospun nanofiber‐coated separator membranes for lithium‐ion rechargeable batteries

Nanofiber‐coated composite membranes were prepared by electrospinning polyvinylidene fluoride‐co‐chlorotrifluoroethylene (PVDF‐co‐CTFE) and PVDF‐co‐CTFE/polyvinylidene fluoride‐co‐hexafluoropropylene (PVDF‐co‐HFP) onto six different Celgard® microporous battery separator membranes. Application of a PVDF‐based copolymer nanofiber coating onto the surface of the battery separator membrane provides a method for improving the electrolyte absorption of the separator and the separator‐electrode adhesion. Peel tests showed that both PVDF‐co‐CTFE and PVDF‐co‐CTFE/PVDF‐co‐HFP nanofiber coatings have comparable adhesion to the membrane substrates. Electrolyte uptake capacity was investigated by soaking the nanofiber‐coated membranes in a liquid electrolyte solution. PVDF‐co‐CTFE and PVDF‐co‐CTFE/PVDF‐co‐HFP nanofiber‐coated membranes exhibited higher electrolyte uptake capacities than uncoated membranes. It was also found that PVDF‐co‐CTFE nanofiber‐coated membranes have higher electrolyte uptakes than PVDF‐co‐CTFE/PVDF‐co‐HFP nanofiber‐coated membranes due to the smaller diameters of PVDF‐co‐CTFE nanofibers and higher polarity of PVDF‐co‐CTFE. The separator–electrode adhesion properties were also investigated. Results showed PVDF‐co‐CTFE and PVDF‐co‐CTFE/PVDF‐co‐HFP nanofiber coatings improved the adhesion of all six membrane substrates to the electrode. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Lewis acid–base property of P(VDF‐co‐HFP) measured by inverse gas chromatography

Poly (vinylidene fluoride‐co‐hexafluoropropylene) P(VDF‐co‐HFP) is an excellent material for polymer electrolytes of lithium ion battery. To enhance the lithium ion transference number, some metal oxides were often embedded into P(VDF‐co‐HFP). The promising mechanism for the increase in lithium ionic conductivity was Lewis acid‐base theory. In this experiment, the Lewis acid–base properties of P(VDF‐co‐HFP) were measured by inverse gas chromatography (IGC). The Lewis acid constant K_a of P(VDF‐co‐HFP) is 0.254, and the base constant K_b is 1.199. Compared with other polymers characterized by IGC, P(VDF‐co‐HFP) is the strongest Lewis basic polymers. Except aluminum ion, lithium ion is the strongest Lewis acidic ion according to their η value of Lewis acids. Therefore, a strong Lewis acid–base interaction will exist between lithium ion and P(VDF‐co‐HFP). This will restrict the transference of lithium ion in P(VDF‐co‐HFP). To enhance the lithium ion transference by blending other metal ions into P(VDF‐co‐HFP), it is suggested that the preferential ions should be Al³⁺, Mg²⁺, Na⁺, and Ca²⁺ because these metal ions have relative large η values. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Preparation and properties of cross‐linked poly(ethylene glycol)/poly[(vinylidene fluoride)‐co‐hexafluoropropylene] interpenetrating network‐type electrolytes for secondary lithium batteries

Cross‐linked poly(ethylene glycol)/poly[(vinylidene fluoride)‐co‐hexafluoropropylene] (XPEG/PVDF–HFP) gel‐type polymer electrolyte interpenetrating polymer networks (IPNs) were prepared by cross‐linking the PEG molecules in the presence of PVDF–HFP molecules. Thermal, mechanical, swelling and electrochemical properties, as well as microstructures of the prepared polymer electrolytes, were investigated for various polymer compositions. The mechanical strength increased, but the swelling ratio in electrolyte solution decreased with increasing PVDF–HFP content. The ion conductivity was highly affected by the type of electrolyte salt, and increased with increasing XPEG concentration. The Arrhenius‐type relationship was observed in the temperature dependence of ion conductivity. The polymer electrolyte systems prepared in this study were electrochemically stable up to about 5 V. Copyright © 2005 Society of Chemical Industry     

Temperature and frequency‐dependent creep and recovery studies on PVDF‐HFP/organo‐modified layered double hydroxides nanocomposites

A series of poly(vinylidene fluoride‐co‐hexafluoropropylene) (PVDF‐HFP) loaded with various contents of layered double hydroxides (LDHs) nanoparticles were prepared via a melt mixing method. Detailed investigations on LDH dispersion state in the polymeric matrix conducted by TEM revealed intercalated/exfoliated, and agglomerated structures at low (1 wt %) and high (>3 wt %) loadings of LDH contents, respectively. Wide angle X‐ray scattering and DSC results showed that incorporation of LDH into PVDF‐HFP matrix reduced its overall crystallinity and helped to form polar crystallites, while the crystal size at 020 crystallographic directions was found to be most affected by presence and dispersion state of LDH in the matrix. TGA results showed LDH improved thermal stability of matrix however, unlike many other nanomaterials it significantly reduced the residual mass which highlights catalytic role of LDH in degradation of residual carbon char. Detailed analysis on creep and recovery data over wide range of selected temperatures revealed that the creep compliance of nanocomposites are basically controlled by crystallinity and presence of LDH at low and high temperatures, respectively. Based on obtained storage modulus and creep compliance master curves it was also found that the influence of LDH on decreasing the creep compliance and improving viscoelastic properties of PVDF‐HFP over long time period and over high frequency ranges becomes more pronounced. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46352.     

Effect of the preparation conditions on the morphology and performance of poly(imide) hollow fiber membranes

Poly(imide) (PI) hollow fiber membranes were prepared by using classical phase inversion process. Effects of different external coagulation bath temperatures (ECBT) and various bore flow rates (BFR) on the morphology and separation performance of the membranes were studied. Cross‐section, inner and outer structures were characterized by using scanning electron microscope and atomic force microscopy (AFM). Mean pore size, pore size distribution, and mean roughness of the PI hollow fibers surfaces were estimated by AFM. It was found that the hollow fibers morphology composed of sponge‐like and finger‐like structures with different ECBT and BFR. A circular shape of the nodules with different sizes was observed in the outer surface of the PI hollow fibers. Mean pore size of the outer surface increases with increasing ECBT and BFR. The important result observed in this study is that the ECBT clearly has the largest effect on hollow fiber PI membrane roughness compared with the BFR. Pure water permeability of the PI hollow fibers was improved with increase of ECBT and BFR. The solute rejection (R%) was reduced when the ECBT and BFR was increased. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40428.     

Dielectric and conducting behavior of pyrene functionalized PANI/P(VDF‐co‐HFP) blend

Herein, we present the dielectric and electrical conductivity properties of the partially miscible polymer blend prepared using pyrene functionalized polyaniline (pf‐PANI) and poly(vinylidene fluoride‐co‐hexafluoro propylene) (PVDF‐co‐HFP). The blend mostly retains the fluorescent nature of pf‐PANI as well as can be moldable and possesses good damping property. The dielectric properties have been investigated as a function of temperature at three different frequencies and the plausible origin of polarization responsible for dielectric behavior in this blend has been identified. The experimental results of dielectric measurements are compared with theoretical models and discussed. The surface morphology of the samples has been examined with a scanning electron microscope. The electrical conductivity has also been studied as a function of temperature and explained in terms of hopping of charge carriers/interconnected networks. The combined dielectric and conductivity results together with scanning electron microscope micrographs, reveal that there is hindrance to achieve percolation threshold even after pf‐PANI addition of 57 vol % and subsequent thermal treatment. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 44077.     

Preparation of PVDF hollow‐fiber membranes via immersion precipitation

Porous polyvinylidene fluoride (PVDF) hollow‐fiber membranes with high porosity were fabricated using the immersion precipitation method. Dimethylacetamide (DMAc) and N‐methyl‐2‐pyrrolidone (NMP) were used as solvent, respectively. In addition, polyvinylpyrrolidone (PVP), lithium chloride, and organic acids were employed as nonsolvent additives. The effects of the internal and external coagulation mediums on the resulting membrane properties were also investigated. The resulting hollow‐fiber membranes were characterized in terms of maximum pore radius, mean pore radius, effective surface porosity as well as wetting pressure. The structures of the prepared hollow fibers were examined using a scanning electron microscope. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 1643–1653, 2001     

Modified poly(vinylidene fluoride) hollow fiber composite membranes reinforced by hydroxyapatite nanocrystal whiskers

The modified poly(vinylidene fluoride) (PVDF) hollow fiber composite membranes reinforced by hydroxyapatite (HAP) nanocrystal whiskers were fabricated with wet‐spinning method. The PVDF/HAP/N‐methyl‐2‐pyrrolidone dope solutions experienced delayed demixing mechanism, and the precipitation rate slightly increased as the HAP whisker content increased. The cross sections of PVDF‐HAP and neat PVDF hollow fiber composite membranes were composed of five distinct layers: two skin layers, two finger‐like sublayers, and a sponge‐like layer. The Young's modulus of and tensile strength of the PVDF‐HAP hollow fiber membranes gradually increased with the addition of nano‐HAP whiskers. The elongation ratio was also improved, which was different from the polymeric membranes modified by other inorganic nanofillers. The permeation flux of the PVDF‐HAP hollow fiber membranes slightly increased with the increase of HAP content in the composite membranes as its hydrophilicity was improved. The crystallization behaviors of PVDF in the composite membranes were also investigated. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Preparation and characterization of proton exchange membrane based on polyphosphoric acid modified by PVDF‐HFP

A polyphosphoric acid functionalized proton exchange membrane (PEM) was prepared by a ring opening reaction using the epoxycyclohexylethyltrimethoxysilane (EHTMS) and amino trimethylene phosphonic acid (ATMP) as raw materials and was modified by poly(vinylidene fluoride)–hexafluoro propylene (PVDF‐HFP). The structure of the membranes was characterized by Fourier transform infrared and scanning electron microscopy. The X‐ray photoelectron spectroscopy explores the content of the elements in the membrane related to the ion exchange capacity value. The membranes’ properties including water uptake, swelling ratio, proton conductivity, and hydrolysis stability were studied. Performance tests show that when ATMP/EHTMS = 1/5, conductivity of the PVDF‐HFP modified PEMs increased from 0.83 × 10^?4 S cm^?1 at 20 °C to 9.53 × 10^?3 S cm^?1 at 160 °C, the swelling ratio of membranes decreased from 2.71% to 2.13%. The results indicate that the introduction of F atoms is beneficial to increase the proton conductivity and the dimensional stability. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46737.     

Modification of electrospun poly(vinylidene fluoride‐co‐hexafluoropropylene) membranes through the introduction of poly(ethylene glycol) dimethacrylate

For the modification of an electrospun poly (vinylidene fluoride‐co‐hexafluoropropylene) (PVDF–HFP) membrane for its potential use as an electrolyte or separator in lithium batteries, poly(ethylene glycol) dimethacrylate (PEGDMA) was introduced into a polymer solution for electrospinning. A post heat treatment of the as‐electrospun membrane at an elevated temperature was performed for PEGDMA polymerization, and this was verified by Fourier transform infrared spectroscopy. The results showed that no significant variations in the membrane morphology were detected when a small amount of PEGDMA (PVDF–HFP/PEGDMA mass ratio = 4/1) was incorporated. This electrospun membrane after heat treatment at 130°C for 2 h exhibited a significantly higher tensile strength (6.26 ± 0.22 MPa) than that of an electrospun PVDF–HFP membrane (3.28 ± 0.35 MPa) without PEGDMA. The porosity and liquid absorption of the electrospun PVDF–HFP/PEGDMA (4/1) membrane were 70.0 ± 1.6% and 267 ± 11%, respectively, lower than those of the electrospun PVDF–HFP membrane (76.5 ± 0.3% and 352 ± 15%) because of the introduction of PEGDMA. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Highly selective sulfonated poly(vinylidene fluoride‐co‐hexafluoropropylene)/poly(ether sulfone) blend proton exchange membranes for direct methanol fuel cells

Proton exchange membranes (PEMs) based on blends of poly(ether sulfone) (PES) and sulfonated poly(vinylidene fluoride‐co‐hexafluoropropylene) (sPVdF‐co‐HFP) were prepared successfully. Fabricated blend membranes showed favorable PEM characteristics such as reduced methanol permeability, high selectivity, and improved mechanical integrity. Additionally, these membranes afford comparable proton conductivity, good oxidative stability, moderate ion exchange capacity, and reasonable water uptake. To appraise PEM performance, blend membranes were characterized using techniques such as Fourier transform infrared spectroscopy, AC impedance spectroscopy; atomic force microscopy, and thermogravimetry. Addition of hydrophobic PES confines the swelling of the PEM and increases the ultimate tensile strength of the membrane. Proton conductivities of the blend membranes are about 10^?3 S cm^?1. Methanol permeability of 1.22 × 10^?7cm² s^?1 exhibited by the sPVdF‐co‐HFP/PES10 blend membrane is much lower than that of Nafion‐117. AFM studies divulged that the sPVdF‐co‐HFP/PES blend membranes have nodule like structure, which confirms the presence of hydrophilic domain. The observed results demonstrated that the sPVdF‐co‐HFP/PES blend membranes have promise for possible usage as a PEM in direct methanol fuel cells. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43907.     

Temperature‐dependent transition of crystal phases in the electrospinning process of poly(vinylidene fluoride‐co‐hexafluoropropylene)

The temperature‐dependent transition of the crystal phases of poly(vinylidene fluoride‐co‐hexafluoropropylene) (PVDF‐HFP) was investigated in the electrospinning process. A solution of PVDF‐HFP in N,N‐dimethyl acetamide (DMAc) produced only the β‐phase‐dominant crystal up to 70 °C, irrespective of the spinneret temperature. In a mixed solvent of DMAc and acetone, however, the crystal phase of the electrospun fibers was dependent on temperature: β‐phase‐dominant at 30 and 50 °C and α‐phase‐dominant at 70 °C. The transition was related to a change of the coagulation rate during electrospinning, because the less perfect α phase is preferable to the β phase at a higher coagulation rate. The temperature‐dependent increase of the coagulation rate was more drastic in the presence of acetone, so the transition took place only in the mixed solvent. At elevated temperature, acetone not only raised the evaporation rate of the solvent but promoted the phase separation of the polymer resulting from the lower critical solution temperature behavior, which was rheologically traced. © 2019 Society of Chemical Industry     

Structure formation and characterization of PVDF hollow fiber membranes by melt‐spinning and stretching method

Melt‐spinning and stretching (MS‐S) method was proposed for preparing poly(vinylidene fluoride) (PVDF) hollow fiber membranes with excellent mechanical properties. The morphology and properties of PVDF fibers and membranes were investigated by small angle X‐ray scattering (SAXS), differential scanning calorimeter (DSC), field emission scanning electron microscope, mercury porosimeter, and tensile experiment. SAXS results indicated that the stacked lamellar structure aligned normal to the fiber axis was separated and deformed when the fibers were strained, and the long period of the strained fibers increased accordingly. Factors affecting the membrane properties were mainly spin‐draw ratio, annealing temperature, time, and stretching rate. Experimental results showed that the average pore size, porosity, and N₂ permeation of the membranes all increased with the increasing spin‐draw ratios and annealing temperatures. Annealing the nascent PVDF hollow fibers at 145°C for 12 h was suitable for attaining membranes with good performance. In addition, the amount and size of the micropores of the membrane increased obviously with stretching rate. Tensile experiment indicated PVDF hollow fiber membranes made by MS‐S process had excellent mechanical properties. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Characterization of polyacrylonitrile,poly(acrylonitrile‐co‐vinyl acetate), and poly(acrylonitrile‐co‐itaconic acid) based activated carbon nanofibers

In this study, three different acrylonitrile (AN)‐based polymers, including polyacrylonitrile (PAN), poly(acrylonitrile‐co‐vinyl acetate) [P(AN‐co‐VAc)], and poly(acrylonitrile‐co‐itaconic acid) [P(AN‐co‐IA)], were used as precursors to synthesize activated carbon nanofibers (ACNFs). An electrospinning method was used to produce nanofibers. Oxidative stabilization, carbonization, and finally, activation through a specific heating regimen were applied to the electrospun fibers to produce ACNFs. Stabilization, carbonization, and activation were carried out at 230, 600, and 750 °C, respectively. Scanning electron microscopy, thermogravimetric analysis (TGA), and porosimetry were used to characterize the fibers in each step. According to the fiber diameter variation measurements, the pore extension procedure overcame the shrinkage of the fibers with copolymer precursors. However, the shrinkage process dominated the scene for the PAN homopolymer, and this led to an increase in the fiber diameter. The 328 m²/g Brunauer–Emmett–Teller surface area for ACNFs with PAN precursor were augmented to 614 and 564 m²/g for P(AN‐co‐VAc) and P(AN‐co‐IA), respectively. The TGA results show that the P(AN‐co‐IA)‐based ACNFs exhibited a higher thermal durability in comparison to the fibers of PAN and P(AN‐co‐VAc). The application of these copolymers instead of AN homopolymer enhanced the thermal stability and increased the surface area of the ACNFs even in low‐temperature carbonization and activation processes. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44381.     

Temperature‐sensitive PVDF hollow fiber membrane fabricated at different air gap lengths

This article describes preparation of temperature‐sensitive poly(vinylidene fluoride) hollow fiber membranes using the dry‐wet spinning technique and investigates effects of air gap length on the structures and performances. In spinning these hollow fibers, N,N‐dimethyl formamide and poly(ethylene glycol) (10,000) were used as the solvent and pore‐forming agent, respectively. The prepared fiber membranes were characterized by scanning electron microscopy, pore size measurement, filtration experiments of pure water flux, and solutes with different molecular weights. The fiber membranes exhibit a quite asymmetric structures consisting of double skin layers situated on the fiber walls, two finger‐like layers near skin layers as well as macrovoids and sponge‐like structures at the center of the fiber cross‐sections. Remarkable changes of pure water flux and retention of solute are observed around 32°C, indicating an excellent temperature‐sensitive permeability. As the air gap length increases, the pore size of fiber membrane decreases, which results in decrease of pure water flux and allows small molecules to permeate through the fiber membrane. POLYM. ENG. SCI., 53:2519–2526, 2013. © 2013 Society of Plastics Engineers     

Long‐term study of CO2 absorption by PVDF/ZSM‐5 hollow fiber mixed matrix membrane in gas–liquid contacting process

In order to fabricate hollow fiber mixed matrix membrane (HFMMM) for long‐term CO₂ absorption process, ZSM‐5 (Zeolite Socony Mobil–5) zeolite was modified using hexadecyltrichlorosilane for increasing hydrophobicity and then added to the polyvinylidene fluoride (PVDF) spinning dope. The in‐house made HFMMMs were characterized in terms of gas permeance, overall porosity, average pore size, effective surface porosity, surface roughness, mechanical stability, and wetting resistance. The morphology of the HFMMMs was studied using SEM. The cross‐sectional SEM images indicated that the membrane structure has changed from sponge‐like to finger‐like by ZSM‐5 loading. The surface roughness increased by increasing ZSM‐5 concentration in the spinning dope. The HFMMM spun from the spinning dope with 0.5 wt % of ZSM‐5 zeolite showed that the CO₂ absorption flux decreased 18.9% in the initial 115 h of the operation and then the absorption flux remained constant until the end of the operation. For plain PVDF HFM the absorption flux decreased 36% from the initial value in the first 15 h of the experiment. Thus it could be concluded that the long term stability of HFM was improved by the incorporation of ZSM‐5. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44606.     

Structure and Performance of Poly(vinylidene chloride‐co‐vinyl chloride) Porous Membranes with Different Additives

Poly(vinylidene chloride‐co‐vinyl chloride) (P(VDC‐co‐VC) membranes were prepared by non‐solvent‐induced phase separation and adjusted by adding water‐soluble polyethylene glycol (PEG) and water‐insoluble silicon dioxide (SiO₂) hydrophilic nanoparticles. The structure of pores and antifouling performance were investigated to illustrate the effect of these nanoparticles. The cross section of the P(VDC‐co‐VC) membrane exhibited more macropores and the typical finger‐like pores turned into more vertically interconnected ones with increasing PEG content, while the number and size of finger‐like pores became less with increasing SiO₂ content. Considering the filtration and antifouling experiments, the presence of hydrophilic PEG and SiO2 nanoparticles in the P(VDC‐co‐VC) polymer matrix improved the membrane performance in terms of high flux, high BSA rejection ratio, and fouling resistance.