Adhesion of surface‐grafted low‐density polyethylene plates with enzymatically modified chitosan solutions

An investigation was undertaken on application of dilute chitosan solutions modified by tyrosinase‐catalyzed reaction with 3,4‐dihydroxyphenetylamine (dopamine) to adhesion of the low‐density polyethylene (LDPE) plates surface‐grafted with hydrophilic monomers. Tensile shear adhesive strength effectively increased with an increase in the grafted amount for methacrylic acid‐grafted and acrylic acid‐grafted LDPE (LDPE‐g‐PMAA and LDPE‐g‐PAA) plates. In particular, substrate breaking was observed at higher grafted amounts for LDPE‐g‐PAA plates. The increase in the amino group concentration of the chitosan solutions and molecular mass of the chitosan samples led to the increase in adhesive strength. Adhesive strength of the PE‐g‐PMAA plates prepared at lower monomer concentrations sharply increased at lower grafted amounts, which indicates that the formation of shorter grafted PMAA chains is an effective procedure to increase adhesive strength at lower grafted amounts. Infrared measurements showed that the reaction of quinone derivatives enzymatically generated from dopamine with carboxyl groups was an important factor to increase adhesive strength in addition to the formation of the grafted layers with a high water absorptivity. The above‐mentioned results suggested that enzymatically modified dilute chitosan solutions can be applied to an adhesive to bond polymer substrates. The emphasis is on the fact that water is used as a solvent for preparation of chitosan solutions and photografting without any organic solvents. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Studies on the surface properties and the adhesion to metal of polyethylene coatings modified with primary aromatic amines

The surface free energy and acid–base characteristics of polyethylene coatings formed on steel in the presence of primary aromatic amines (PAAs) were investigated. PAAs were shown to interact with steel by a donor–acceptor mechanism. An increase in the coating adhesion is realized through chemical and physical bond formation between an adhesive and a substrate with the help of the PAA. The free surface energy of the contact‐to‐metal side of these coatings modified with PAA was shown to grow in parallel with the increase in adhesion. The results correlate with the data on polyethylene surface wetting with nonionic surfactants. Acid–base interactions were found to exert primary control over polyethylene's adhesion to steel. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 79: 388–397, 2001     

Improvement in adhesive‐free adhesion by the use of electrostatic interactions between polymer chains grafted onto polyethylene plates

The tensile shear adhesive‐free adhesion properties induced by electrostatic interactions between poly(acrylic acid) (PAA) and poly[2‐(dimethylamino)ethyl methacrylate] (PDMAEMA) chains grafted onto polyethylene (PE) with low‐density (LDPE) or high‐density (HDPE) plates were studied. PAA‐ or PDMAEMA‐grafted PE plates were immersed in a HCl or NaOH solution or water for 24 h, and their electrostatic properties were changed before they were overlapped with each other and heat‐pressed. The breaking of the substrate between the two plates with water‐swollen grafted layers was observed in the low range of grafted amounts in comparison with immersion in the acidic and basic solutions. The ability of the two plates with grafted polymer chains swollen in water to strongly bond with each other was a result of electrostatic interactions formed by positively charged PDMAEMA and negatively charged PAA chains. The breaking of the substrate in the case of adhesive‐free adhesion between quaternized PDMAEMA‐grafted and PAA‐grafted PE plates immersed in the basic solution occurred with lower grafted amounts of PAA. This came from the strong attractive force between dissociated anionic PAA chains and quaternized cationic PDMAEMA chains in the basic solution. In addition, the adhesive‐free adhesion strength of HDPE plates with the same grafted polymer chains encountered the breaking of the substrate with lower grafted amounts than that of LDPE plates. It was concluded that the grafting of polymer chains onto HDPE plates with high crystallinity was considerably restricted to the outer surface regions. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 2632–2638, 2006     

An investigation of cure and thermal stability of poly(amide‐amidic acid) modified tetraglycidyl 4,4′‐diaminodiphenylmethane/4,4′‐diaminodiphenylsulfone

In this work, poly(amide‐amidic acid) (PAA) was used to modify tetraglycidyl 4,4′‐diaminodiphenylmethane (TGDDM)/4,4′‐diaminodiphenylsulfone (DDS) system. Results of non‐isothermal differential scanning calorimetry analysis indicated that PAA played a role of catalyst during the process of the curing reaction. The curing mechanism was studied by Fourier transform infrared spectroscopy, showing that the PAA acted as a co‐curing agent in the system. The glass transition temperature decreased firstly and then increased with the increase of the PAA content. PAA equally rendered TGDDM more fire resistant with higher char yield. On examining the fracture surface morphology using scanning electron microscopy, it was observed that there was no obvious phase separation when the content of PAA was less than 20 phr (per hundred weight of TGDDM/DDS resin), however, phase separation was observed when the content of PAA was 25 and 30 phr. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Improved cell adhesion of poly(amino acid) surface by cyclic phosphonate modification for bone tissue engineering

Poly(amino acid) (PAA) has been currently used as organic part of biocomposites for bone regeneration and reconstruction, but a poor cell adhesive surface becomes its major limitation. In this study, a novel strategy to improve cell adhesion of PAA by introducing a phosphonate (CP) unit into main chain of PAA was proposed. Copolymerizing with CP, the cell adhesion ability of the copolymers was effectively and efficiently improved, corresponding to an adjusted surface wettability. The structure and modification mechanism of copolymers were completely studied based on their surface cell adhesion ability, intrinsic viscosity, compressive strength, X‐ray photoelectron spectroscopy, Fourier transforms infrared spectra, X‐ray diffractometer, and water contact angle analyses. The surface wettability of PAA increased due to the formation of more hydrophilic groups (phosphoramide groups, carboxylic ester groups, and phosphomonoester groups) and stronger hydrogen bonds, which were induced by addition of CP. With a CP content of 1% and 2.5%, corresponding copolymers possessed sufficient compressive strength for bone repair and superior surface wettability 54.3° and 54.1° for mesenchymal stem cells adhesion. Since this valuable additional method improves cell adhesion ability of PAA surface, application of the PAA for bone tissue engineering would be broadened. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46226.     

Adhesion of grafted polypropylene plates with enzymatically modified chitosan solutions and analysis of failed surfaces by X‐ray photoelectron spectroscopy

In this study, hydrophilic monomers were photografted onto the PP plates at different monomer concentrations and temperatures, and grafted PP plates were bonded with enzymatically modified chitosan solutions. Their adhesive strength properties were discussed in relation to the grafting conditions and hydrophilic properties such as wettability and water‐absorptivity. In addition, the location of failure was investigated by X‐ray photoelectron spectroscopy analysis of failed surfaces. Wettability of the grafted PP plates except for the PP grafted with acrylic acid (PP‐g‐PAA) plates remained constant above the grafted amounts at which the PP surfaces were fully covered with grafted polymer chains. On the other hand, wettability of the PP‐g‐PAA plates passed through the maximum value and then gradually decreased with the grafted amount probably because of the aggregation of grafted PAA chains. Water‐absorptivity of the grafted layers formed at lower monomer concentrations or temperatures sharply increased at lower grafted amounts. The adhesive strength increased with an increase in the grafted amount and substrate breaking was observed for PP‐g‐PAA plates because enzymatically modified chitosan solutions were successfully penetrated in the grafted layers and quinone derivatives reacted with carboxy groups of grafted PAA chains. Failure occurred in the layers composed of grafted PAA chains and components containing in enzymatically modified chitosan solutions and the location was shifted to the inside of grafted layer, as the grafted amount increased. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 1369‐1376, 2013     

Efficient dispersants for the dispersion of gallium zinc oxide nanopowder in aqueous suspensions

Appropriate dispersants for the dispersion of gallium zinc oxide (GZO) nanopowder in aqueous suspensions were identified in this study. The dispersion efficiencies and stabilization mechanisms of water‐based dispersants ammonium poly(acrylic acid) (PAA–NH₄), an anionic polyelectrolyte, and polyethylenimine (PEI), a cationic polyelectrolyte, were compared. The experimental analyses of rheology and sedimentation showed that both PAA–NH₄ and PEI were good dispersants for the dispersion of GZO. Theoretical calculations based on Derjaguin‐Landau‐Verwey‐Overbeek theory revealed that the stabilization mechanism of PEI was mainly related to the steric effect, and a very low molecular weight of 1800 g/mol was insufficient for powder stabilization. GZO was well dispersed by PEI with high molecular weight of 10 000 g/mol, but agglomeration occurred when too much PEI was added. Compared with PEI, PAA–NH₄ was more efficient because of its high contribution to the increase in electrostatic repulsion. Based on theoretical considerations on both steric and electrostatic effects, namely, the electrosteric stabilization mechanism, PAA–NH₄ is optimal for the dispersion of GZO nanopowder in aqueous suspensions.     

Novel fishnet fibers with anti‐adhesion of seaweeds obtained by UV‐irradiation technique

A novel Nylon‐6 fishnet fiber with the antiadhesion of seaweeds was prepared by UV radiation‐initiated grafting of acrylic acid (AA) onto Nylon‐6 fibers, and its structure was characterized by scanning electron microscopy (SEM) and Fourier transform infrared spectroscopy (FTIR). The influences of grafting conditions, such as irradiation dose, temperature, concentration of monomer, inorganic acid, and inhibitor etc., on grafting rate were studied, and the antiadhesion of seaweeds was evaluated with Dunaliella. The results showed that the grafting amount of Nylon‐g‐AA was increased with the increase of irradiation time. With the increase of concentration of AA, temperature, reaction time, inorganic acid, and inhibitor, the grafting amount increased firstly and then decreased, respectively. Nylon‐6 fibers modified by Poly(acrylic acid) (PAA) had a strong effect on the adhesion of Dunaliella, and the antiadhesion was improved with the increase of the grafting amount. Results from the mechanical analysis revealed that the tensile strength of the UV‐irradiation fibers decreased. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 1252–1256, 2007     

Preparation,characterization and in vitro drug release properties of polytrimethylene carbonate/polyadipic anhydride blend microspheres

Polyadipic anhydride (PAA), an aliphatic polyanhydride, and polytrimethylene carbonate (PTMC), an aliphatic polycarbonate, were synthesized via ring opening polymerization of oxepan‐2,7‐dione and melt‐condensation of trimethylene carbonate (1,3 dioxan‐2‐one), respectively. PTMC–PAA blend microspheres containing different ratios of buprenorphine HCl (2, 5, and 10%) were prepared by an oil‐in‐oil emulsion solvent removal method. Microspheres with different ratios of PTMC–PAA (85/15, 70/30, and 55/45) containing 5% buprenorphine HCl were prepared. Microspheres were spherical with visible cracks and pores on the surface. The average particle size of microspheres was around 200 μm for all microspheres. Drug loading efficiency of PTMC–PAA microspheres (85/15, 70/30, and 55/45) was 97.2, 95.2, and 70.2%, respectively. With the increase in the PTMC ratio, the melting point and the enthalpy of melting were both decreased. The mechanism for drug release from PTMC–PAA blend microspheres were generally a combination of drug diffusion through polymers and biodegradation of the polymers. In first three days, the release from microspheres followed zero order kinetics and was dependent on the PAA content. After three days the drug release from microspheres followed first order kinetics. In conclusion it was demonstrated that buprenorphine HCl release from microspheres could be successfully controlled by using different ratios of PTMC–PAA blends. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 2377–2383, 2006     

Synthesis and thermal properties of poly(acrylonitrile‐co‐allyl glycidyl ether)‐graft‐methoxypoly(ethylene glycol) copolymers as novel solid–solid phase‐change materials for thermal energy storage

We synthesized a series of poly(acrylonitrile‐co‐allyl glycidyl ether)‐graft‐methoxypoly(ethylene glycol) (PAA‐g‐MPEG) copolymers as novel polymeric solid–solid phase‐change materials by grafting methoxypoly(ethylene glycol) (MPEG) to the main chain of poly(acrylonitrile‐co‐allyl glycidyl ether) (PAA). PAA was the skeleton, and MPEG was a functional side chain, which stored and released heat during its phase‐transition process. Fourier transform infrared spectroscopy and ¹H‐NMR spectroscopy analysis were performed to investigate the chemical structures. The crystalline morphology and crystal structures were also measured with polarized optical microscopy and X‐ray diffraction. Moreover, the thermal‐energy‐storage properties, thermal stability, and thermal reliability of the PAA‐g‐MPEG copolymers were characterized by differential scanning calorimetry and thermogravimetric analysis (TGA) methods. These analysis results indicate that the MPEG chains were successfully grafted onto PAA, and we found that the PAA‐g‐MPEG copolymers had typical solid–solid phase‐transition temperatures in the range 11–54 °C and high latent heat enthalpies between 44 and 85 J/g. In addition, the as‐prepared PAA‐g‐MPEG copolymers showed reusability and thermal reliability, as shown by the thermal cycle testing and TGA curves. Therefore, the synthesized PAA‐g‐MPEG copolymers have considerable potential for thermal energy storage. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46641.     

Improving properties of superabsorbent composite induced by using alkaline protease hydrolyzed‐sericin (APh‐sericin)

A series of superabsorbent polymer composites based on sericin hydrolyzed with alkaline protease (AP) were prepared by grafting with acrylic acid (AA) and acrylamide (AM). The properties of the superabsorbent polymers (SAP) by using hydrolyzed sericin with different amount of alkaline protease (nAPh‐sericin) were compared. It was found that the polymer prepared from 5APh‐sericin (the mass ratio of AP to sericin was 5.0 mg g⁻¹) showed the highest graft percentage and water absorbency, this phenomenon may be attributed to the change of molecular weight of resulting sericin molecules. The molecular structure of the grafted polymers was proved by thermal gravimetric analysis (TGA) and Fourier transform infrared spectroscopy (FTIR) measurements. Comparing with PAA‐AM (poly AA‐co‐AM) and 0APh‐sericin/PAA‐AM polymer, 5APh‐sericin/PAA‐AM polymer had the most excellent water retention capacity and enzyme degradability. The morphological features of the polymers with different drying methods were evidenced by SEM images. The water absorbencies of 5APh‐sericin/PAA‐AM polymer prepared with freeze‐drying were 896 g g⁻¹ in deionized water, 424 g g⁻¹ in tap water, and 83 g g⁻¹ in 0.9 wt% aqueous NaCl solution. POLYM. COMPOS., 35:509–515, 2014. © 2013 Society of Plastics Engineers     

Effects of the surface modification of poly(amino acid)/hydroxyapatite/calcium sulfate biocomposites on the adhesion and proliferation of osteoblast‐like cells

In this study, we focused on the surface modification of a novel poly(amino acid) (PAA)/hydroxyapatite/calcium sulfate composite and the effect of its surface modification on cellular responses. The surface modification was performed by sandblasting (sample S2), calcium chloride ethanol saturated solution etching (sample S3), and formic acid etching (sample S4) followed by in vitro culturing of osteoblast‐like cells. The obtained results indicate that a new interface of the composite was formed during the modification, and the modified surface was changed with respect to its surface morphology by physical abrasion. The calcium chloride ethanol saturated solution etchant etched PAA selectively whereas forming rich calcium‐phosphate (Ca–P) apatite on the surface of S3. The formic acid etchant attacked the inorganic component without changing the PAA state. Cell attachment and cell proliferation were improved by the treatments of S2 and S3 in comparison with no treatment and the treatment of S4 © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42427.     

Preparation and adsorption properties of chitosan–poly(acrylic acid) nanoparticles for the removal of nickel ions

Chitosan (CS) nanoparticles with different mean sizes ranging from 100 to 195 nm were prepared by ionic gelation of CS and poly(acrylic acid) (PAA). Variations in the final solution pH value and CS : PAA volume ratio were examined systematically for their effects on nanoparticle size, intensity of surface charge, and tendency toward particle aggregation. The sorption capacity and sorption isotherms of the CS–PAA nanoparticles for nickel ions were evaluated. The parameters for the adsorption of nickel ions by the CS–PAA nanoparticles were also investigated. The CS–PAA nanoparticles could sorb nickel ions effectively. The sorption rate for nickel ions was affected significantly by the initial concentration of the solution, sorbent amount, particle size, and pH value of the solution. The samples of nanoparticles were well correlated with Langmuir's isotherm model, and the adsorption kinetics of nickel correlated well with the pseudo‐second‐order model. The maximum capacity for nickel sorption deduced from the use of the Langmuir isotherm equation was 435 mg/g, which was significantly higher than that of the micrometer‐sized CS. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

Swelling behavior and pervaporation properties of new composite membrane systems: Porous polyethylene film‐poly(acrylic acid) hydrogel

A new type of composite membrane for pervaporation has been developed. These membranes were prepared by free‐radical copolymerization of acrylic acid with a macromolecular polyfunctional crosslinker (allylhydroxyethylcellulose) inside the porous polyethylene (PE) film. It was shown that the porous structure of the PE matrix is filled with poly(acrylic acid) (PAA), and a layer of acid is formed on the film surface. To investigate the effect of the porous matrix on the composite membrane properties, a hydrogel membrane of crosslinked PAA was also prepared without the matrix using the same procedure. PAA in both membranes was in the neutralized form (K⁺). Swelling behavior of the membranes and their separation characteristics for pervaporation were investigated in water–ethanol solutions depending on the ethanol concentration. All membranes exhibited a high degree of equilibrium swelling (Q = 20–50 g/g) in dilute ethanol solutions (0–30 vol %), and Q sharply dropped to 1.5–2 g/g at a EtOH concentration of 30–40 vol % due to collapse of the gel. All membranes under study were highly permeable and selective to water over a wide range of ethanol concentrations in the feed (50–96 vol %), but composite membranes had a higher separation factor due to the restriction effect of the matrix porous structure on swelling of PAA(K⁺) inside the pores. However, composite membranes were characterized by a lower permeation rate, compared to the crosslinked PAA membranes without a matrix, because of their lower effective surface for diffusion. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 1461–1465, 2004     

Ab initio reversible addition–fragmentation chain transfer emulsion polymerization of styrene/butyl acrylate mediated by poly(acrylic acid)‐block‐polystyrene trithiocarbonate

Ab initio reversible addition–fragmentation chain transfer (RAFT) emulsion polymerization of styrene/butyl acrylate was investigated with the trithiocarbonate macro‐RAFT agent poly(acrylic acid)‐block‐polystyrene (PAA‐b‐PS) as a stabilizer and a RAFT agent. Influences of the amount of ammonium persulfate (APS), the amount of PAA‐b‐PS and the mass ratio of monomers on emulsion polymerization and film properties are discussed. The particle morphology exhibited spherical‐like structure with particles of about 90 nm in diameter and relatively narrow particle size distribution characterized using transmission electron microscopy and dynamic laser scattering. Fourier transform infrared and ¹H NMR spectra showed that the styrene/butyl acrylate emulsion was successfully synthesized. The monomer conversion increased initially with increasing amount of APS, from 0.4 up to 0.8 wt%, and then decreased. The particle size increased and its distribution decreased gradually with increasing amount of APS. The monomer conversion increased from 76.83 to 94.21% as the amount of PAA‐b‐PS increased from 3 to 4 wt%, and then decreased with further increase of PAA‐b‐PS. The particle size decreased and its distribution increased with increasing amount of PAA‐b‐PS. The water resistance and solvent resistance of the polymer films initially increased and then decreased with decreasing mass ratio of butyl acrylate to styrene. © 2014 Society of Chemical Industry     

Reinforced soy protein isolate–based bionanocomposites with halloysite nanotubes via mussel‐inspired dopamine and polylysine codeposition

Fully renewable soy protein isolate (SPI)–based film with rigid strength and sufficient water resistance is difficult to attain. In this study, the mussel‐inspired surface chemistry of ?‐poly‐L‐lysine (?‐PL)/dopamine was exploited for codeposition onto halloysite nanotubes (HNTs) to engineer a multinetwork of HNT/SPI bionanocomposite films via physicochemical bonds. A series of ?‐PL/dopamine aqueous solutions at different concentration ratios were employed. The ?‐PL with abundant cationic amine groups could prevent the overoxidation of dopamine on HNT surfaces, thus maintaining sufficient free catechol groups for highly active reactions that improve the biphase interfacial adhesion. Moreover, HNTs surface entangled by ?‐PL chains could be more compatible with peptides. This codeposition of ?‐PL/dopamine on HNT (DLHNT) surfaces was analyzed by X‐ray photoelectron spectroscopy, Fourier transform infrared spectroscopy, X‐ray diffraction, and thermogravimetric analysis. Compared to the control SPI film, the tensile strength of the nanocomposite film (DLHNTs0.5/SPI) was increased from 5.9 MPa to 8.25 MPa, the Young's modulus was improved by 166.4%, and the moisture absorption was reduced to 56.1% (87.2% of the control). In summary, a facile and mild bioinspired surface chemistry of ?‐PL/dopamine codeposition onto HNT surfaces was performed to prepare SPI‐based nanocomposite films with improved interfacial adhesion and benign compatibility. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46197.     

Oxidative graft polymerization of aniline on the modified surface of polypropylene films

A novel method for preparing electrically conductive polypropylene‐graft‐polyacrylic acid/polyaniline (PP‐g‐PAA/PANI) composite films was developed. 1,4‐Phenylenediamine (PDA) was introduced on the surface of PP‐g‐PAA film, and then, chemical oxidative polymerization of aniline on PP‐g‐PAA/PDA film was carried out to prepare PP‐g‐PAA/PANI electrically conductive composite films. After each step of reaction, the PP film surface was characterized by attenuated total reflectance Fourier transform infrared spectroscopy. Static water contact angles of the PP, PP‐g‐PAA, and PP‐g‐PAA/PANI films were measured, and the results revealed that graft reactions took place as expected. The morphology of the PP‐g‐PAA film and the PP‐g‐PAA/PANI composite film were observed by atomic force microscopy. The conductivity and the thickness of the PP‐g‐PAA/PANI composite films with 1.5 wt % PANI were around 0.21 S/cm and 0.4 μm, respectively. The PANI on the PP‐g‐PAA/PANI film was reactivated and chain growing occurred to further improve the molecular weight of PANI. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 2442–2450, 2007     

Formation of multilayer poly(acrylic acid)/poly(vinylidene fluoride) composite membranes for pervaporation

Dual‐ and multilayer composite membranes, consisting of poly(acrylic acid) (PAA) and poly(vinylidene fluoride) (PVDF), were synthesized by the plasma‐induced polymerization technique. The dual‐layer membrane had a dense PAA layer grafted onto a microporous PVDF substrate, whereas in the multilayer membranes, the grafted PAA and the PVDF layers were arranged in an alternating sequence (e.g., PAA/PVDF/PAA and PAA/PVDF/PAA/PVDF/PAA). These membranes were used in a pervaporation process to separate ethanol–water solutions. For the dual‐layer membranes, the results indicated that the separation factor increased and the permeation flux decreased with increasing amounts of grafted PAA. For the case of grafting yield < 0.6 mg/cm², the composite membrane demonstrated poor separation. As the grafting yield reached 0.85 mg/cm², a sharp increase of the separation factor was observed. For the multilayer membranes, the pervaporation performances were very good, with high separation factors (on the order of 100) and reasonable permeation fluxes over a wide ethanol concentration range. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 2266–2274, 2004     

Effect of poly(acrylic acid)‐g‐PCL microstructure on the mechanical properties of starch/PCL blend compatibilized with poly(acrylic acid)‐g‐PCL

Poly(acrylic acid)‐g‐polycaprolactone (PAA‐g‐PCL) graft copolymer was synthesized and starch/PCL blends compatibilized with PAA‐g‐PCL were prepared. The mechanical properties of the starch/PCL blends compatibilized with various PAA‐g‐PCLs that have different graft degrees and graft lengths were investigated. As the graft degree of the PAA‐g‐PCLs that have the same graft length increased, the modulus and the strength of the blends decreased. However, the elongation at break and the tensile toughness of the blends showed a maximum at a certain graft degree (10.8 mol%) owing to the better compatibilizing effect compared to the low (3.9 mol%) and the high (23.4 mol%) graft degree of PAA‐g‐PCL. It was also found that the modulus and the strength of the blends increased with the increase of graft length of the PAA‐g‐PCLs that have the same graft degree (～11 mol%). However, the blend compatibilized with the short graft length (M.W. of PCL graft: 530) exhibited the highest value of the elongation at break and the tensile toughness. This result is attributed to the self‐crystallization of PAA‐g‐PCL in the blend that has longer PCL grafts.     

Enhanced water flux through graphitic carbon nitride nanosheets membrane by incorporating polyacrylic acid

Membranes assembled from two‐dimensional (2‐D) layered materials have shown potential use in water purification. Recently, a 2‐D graphitic carbon nitride (g‐C₃N₄) nanosheets membrane exhibits considerable separation performance in water purification. In this study, to further improve this water separation performance, polyacrylic acid (PAA) was introduced to tune the nanochannels formed between the g‐C₃N₄ nanosheets. The fabricated g‐C₃N₄‐PAA hybrid membranes possessed higher water flux without sacrificing much rejection rate compared with that of the g‐C₃N₄ membrane; however, noticeable fouling was observed upon addition of the PAA into the membrane composite structure. In addition, the effect of PAA on the morphology, surface hydrophilicity, separation performance, and antifouling properties of the g‐C₃N₄ membrane were examined in detail. Overall, incorporating PAA into the g‐C₃N₄ nanosheets membrane was an effective and convenient method to improve the water separation performance, which could promote the application of the 2‐D g‐C₃N₄ nanosheets membrane in practical ultrafiltration processes. © 2018 American Institute of Chemical Engineers AIChE J, 64: 2181–2188, 2018