Synthesis and characterization of photo‐crosslinkable polyfluorene with acrylate side‐chains

A photo‐crosslinkable polymer, poly[2,7‐(9,9‐dioctylfluorene)‐co‐2,7‐(9‐hexyl‐9‐(2‐acrylate ethyl)‐9H‐fluorene)] (P3), was synthesized and the photo‐crosslinkable acrylate groups were introduced into the side‐chains of the polyfluorene derivative after its polymerization. This method avoids the possible crosslinkage of the crosslinkable groups on the monomers during polymerization in the traditional synthesis route by the polymerization of the monomers with the crosslinkable side‐chains. The soluble and processable polymer P3 could be crosslinked via the acrylate groups in its side‐chains upon exposure to UV light in nitrogen atmosphere. The crosslinking was confirmed by IR spectroscopy: the IR peak of C?C bond at 1635 cm^?1 decreased and that of the vinyl C? H bond at 742 cm^?1 disappeared after the UV exposure. The absorption spectra of P3 remain unchanged after crosslinking, but a longer wavelength emission at 517 nm appeared in the photoluminescent and electroluminescent spectra of the crosslinked P3, which could be attributed to the formation of keto defects during the photo crosslinking. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 2336–2342, 2006     

Novel polymerizable N‐aromatic maleimides as free radical initiators for photopolymerization

Four kinds of polymerizable N‐aromatic maleimides (MIs)—4‐[(4‐maleimido)phenoxy]benzophenone (MPBP), 4,4′‐bis[(4‐maleimido)phenoxy]benzophenone (BMPBP), 4‐maleimidobenzophenone (MBP), and 4,4′‐bismaleimidobenzophenone (BMBP)—were synthesized as free radical photoinitiators, by introducing directly N‐phenylmaleimide groups or maleimide groups into the molecule of benzophenone (BP). Compared with BP, their UV‐visible spectra have a significantly red‐shifted maximum absorption. The maximum absorption of MIs containing bifunctional maleimide groups is slightly larger than the corresponding monofunctional ones. Choosing an unsaturated tertiary amine N,N‐dimethylaminoethyl methacrylate (DMAEMA) as coinitiator, the photopolymerization of 1,6‐hexanediol diacrylate (HDDA), initiated by these four MIs, was studied through photo‐DSC. The results show that all the MIs are dramatically more efficient than BP. Among them, MPBP is the most efficient, in which the polymerization rate is almost three times as high as that of the BP system. Photoinitiators containing bifunctional maleimide groups, though having higher final conversion, are less efficient than the corresponding monofunctional ones. These polymerizable photoredox systems significantly reduced the migration of the active species, leading to their higher efficiency. Copyright © 2006 Society of Chemical Industry     

Synthesis and photo‐curing behaviors of silicon‐containing (vinyl ether)–(allyl ether) hybrid monomers

A series of silicon‐containing (vinyl ether)–(allyl ether) hybrid monomers used in nano‐imprint lithography resists were synthesized and subjected to photo‐initiated polymerization. The surface energies of the monomers and the resulting polymer films were then investigated. The surface energies of the monomers were very low at less than 15 mJ m^–2. The photo‐curing behaviors of the five hybrid monomers were investigated using real‐time Fourier transform infrared spectroscopy. The monomers were sequentially initiated with cationic (PAG201) and mixed (cationic initiator PAG201, radical initiator ITX or TPO) initiators. The vinyl ether double bond polymerized both rapidly and completely, whereas the allyl ether double bond remained when PAG201 was used as the photo‐initiator and polymerized completely with mixed initiators. The different double bonds of the silicon‐containing (vinyl ether)–(allyl ether) hybrid monomer increased the efficiency of the polymerization and overcame the intrinsic limitations of the free radical and cationic polymerization processes, including strong oxygen inhibition, large volume shrinkage and high humidity sensitivity. The five monomers with low viscosity, low surface energy, good thermal stability and good photo‐polymerization properties were suitable for nano‐imprint photoresists. © 2013 Society of Chemical Industry     

ESR and kinetic study of a novel polymerizable photoinitiator comprising the structure of N‐phenylmaleimide and benzophenone for photopolymerization

A novel polymerizable photoinitiator, 4‐[(4‐maleimido)phenoxy]benzophenone (MPBP) comprising the structure of N‐phenylmaleimide and benzophenone was used for the photopolymerization with N,N‐dimethylaminoethyl methacrylate (DMAEMA) as coinitiator. The ESR spectrum of this photoredox system was studied and compared with BP/DMAEMA; the results showed the same signals of them and verified that N‐phenylmaleimide does not generate radicals. The kinetics for photopolymerization of methyl methacrylate (MMA) using such system was studied by dilatometer. It was found that the polymerization rate was proportional to the 0.3172th power of the MPBP concentration, the 0.7669th power and the 0.1765th power of MMA concentration and DMAEMA concentration respectively; the overall apparent activation energy obtained was 31.88 kJ/mol. The polymerization kinetics of 1,6‐hexanediol diacrylate (HDDA) initiated by such system was studied by photo‐DSC. It showed that the increase in the MPBP concentration, light intensity, and temperature leads to increased polymerization rate and final conversion. The apparent activation energy was 11.25 kJ/mol. This polymerizable photoredox system was significantly favorable for reducing the migration of active species but owning high efficiency. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 2347–2354, 2006     

1‐(bromoacetyl)pyrene and its arsonium salt as novel photoinitiators for styrene polymerization

The photopolymerization of styrene (Sty) in DMSO induced by pyrene (Py), 1‐Acetylpyrene (AP), 1‐(Bromoacetyl) pyrene (BP), and 1‐Acetylpyrene triphenyl arsonium bromide (APAS) has been investigated. Under all conditions employed, Py was completely ineffective. Incorporation of a chromophoric (? COCH₃) moiety introduces photoinitiating activity into Py. It was observed that introduction of Br into AP markedly accelerated the rate of UV irradiation‐induced polymerization. BP was further modified to its arsonium salt (APAS). The kinetics and mechanism of polymerization using BP and APAS as initiators have been investigated in detail. The polymerization with BP followed nonideal kinetics (R_p ∝ [BP]^0.8 [Sty]^1.1) with respect to initiator concentration whereas ideal kinetics (R_p ∝ [APAS]^0.48 [Sty]^1.1) was observed when APAS was used as initiator. Degradative transfer is thought to be mainly responsible for this unusual kinetic behavior for BP–Sty system. The kinetic data proved that BP was more effective and faster initiator than APAS. In both the cases, the mechanism of polymerization was free radical as evident by inhibiting the effect of hydroquinone and ESR studies. IR and NMR spectra showed the atactic nature of polystyrene. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 1793–1798, 2006     

Synthesis and UV curing kinetics of rapidly UV‐curable hyperbranched polycarbosiloxanes

Hyperbranched polycarbosiloxanes with peripheral photo‐crosslinkable groups were synthesized through controllable hydrosilylation reaction from A₂‐type and CB₃‐type monomers. The polymerization of the monomer pairs was monitored using Fourier transform infrared spectroscopy, from which it was found that vinyl silane and methacrylate groups reacted with hydride silane from the beginning of the reaction. The results thus suggest a step‐by‐step polymerization rather than a two‐step process for this system. The polycarbosiloxanes could be cured rapidly in either nitrogen or air atmosphere, this feature making them attractive for potential application as precursors of advanced ceramic devices with complex structures. The effects of light intensity, reaction temperature and atmosphere on the UV curing rate (R_p) and conversion (α) of the photo‐crosslinkable groups were characterized carefully, and the curing kinetics was also investigated systematically. The results show that R_p and α increased with an increase of light intensity or temperature, and that the inhibiting effect of oxygen in air could be suppressed by enhancing the irradiation intensity. Copyright © 2010 Society of Chemical Industry     

Development of low‐shrinkage composites based on novel crosslinking vinylcyclopropanes

Polymerization shrinkage of methacrylate‐based dental composites remains a major concern in restorative dentistry. Cyclic monomers that undergo ring‐opening polymerization are known to exhibit reduced polymerization shrinkage compared to methacrylates. In this article, the synthesis of four crosslinking 1,1‐disubstituted 2‐vinylcyclopropanes bearing rigid spacers is described. These monomers were synthesized by esterification of 1‐ethoxycarbonyl‐2‐vinylcyclopropane‐1‐carboxylic acid with the corresponding diols. The photopolymerization kinetics of these monomers was investigated by photo‐differential scanning calorimeter using bis(4‐methoxybenzoyl)diethylgermane as the photoinitiator. The synthesized vinylcyclopropanes (VCPs) were shown to be more reactive than the frequently used reactive diluent triethylene glycol dimethacrylate. Composites based on these VCPs showed good mechanical properties and exhibited a significantly reduced volumetric shrinkage and shrinkage stress compared to a corresponding dimethacrylate‐based restorative material. This work highlights the excellent potential of VCPs as alternatives to methacrylates in the development of low‐shrinkage dental composites. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45577.     

Photopolymerization kinetics,photorheology and photoplasticity of thiol–ene–allylic sulfide networks

BACKGROUND: Thiol–ene networks are of interest due to their facile photopolymerization and their open network structure. In this work, an allylic disulphide divinyl ether monomer is reacted with tetrathiol and divinyl ether monomers, which allows the network structure to permanently change in shape if stressed while under irradiation. We also study the photo‐differential scanning calorimetry (DSC) kinetics and photorheology during cure and the dynamic mechanical properties after cure. RESULTS: The heat of polymerization is similar for the thiol–ene systems and suggests ca 80% conversion of the vinyl ether groups. An increase in the initiator concentration increases the photocure rate as expected. The activation energy for photopolymerization is 7.6 kJ mol^?1. DSC and rheometry studies show that the polymerization kinetics is slowed by the addition of the allylic disulfide divinyl possibly due to the formation of less reactive radicals. However, as shown by dynamic mechanical thermal analysis, the network structure is not changed very much by addition of this monomer. If radicals are generated by irradiation of a photoinitiator in the network while a stress is being applied, the polymer will permanently deform depending on the fraction of 2‐methylenepropane‐1,3‐di(thioethyl vinyl ether) in the network, due to a bond interchange reaction. CONCLUSION: The rate of thiol–ene reaction is slowed by the addition of the allylic disulfide divinyl ether. Photoplasticity is observed in the networks containing the allylic disulfide groups. Further work is required to optimize the extent of photoplasticity in these systems. Copyright © 2007 Society of Chemical Industry     

Functionalized multiarm poly(ϵ‐caprolactone)s: Synthesis,structure analysis,and network formation

The purpose of this research was to synthesize and characterize a novel class of four‐arm, star‐shape biodegradable polymers having double‐bond functionality as a precursor for free‐radical polymerization, with unsaturated monomers or macromers or photocrosslinking for network formation. The synthesis involved two basic steps. First, hydroxyl‐functionalized four‐arm poly(?‐caprolactone)s (PPCL‐OH) were synthesized by the ring‐opening polymerization of ?‐caprolactone in the presence of pentaerythritol and stannous octoate. Second, double‐bond–functionalized four‐arm poly(?‐caprolactone)s (PPCL‐Ma) were synthesized by reacting PPCL‐OH with maleic anhydride in the melt at 130°C. Quantitative conversion of hydroxyl functionality in PPCL‐OH to double‐bond functionality was achieved for low molecular weight PPCL‐OH. Both the PPCL‐OH and the PPCL‐Ma were characterized by FTIR, ¹H‐NMR, ¹³C‐NMR, SEC, and DSC. The capability of the double‐bond–functionalized four‐arm poly(?‐caprolactone)s (PPCL‐Ma) to form network structures was preliminarily shown by photocrosslinking PPCL‐Ma. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 2296–2306, 2002     

Using aluminium triflate as a co‐catalyst for the polymerization of o‐phenylenediamine and its derivatives

Aromatic diamine monomers, including o‐phenylenediamine (oPD), 4‐methyl‐o‐phenylenediamine (4Me‐oPD), 4,5‐dimethyl‐o‐phenylenediamine (dMe‐oPD) and 4‐(tert‐butyl)‐o‐phenylenediamine (tBu‐oPD), were polymerized by chemical oxidation using ammonium persulfate as an oxidant. Aluminium triflate (Al(OTf)₃) was also used for the first time as a co‐catalyst under various reaction conditions for the polymerization of oPD derivatives. The polymerization yield was improved when Al(OTf)₃ was introduced to the polymerization reaction for most polymers. The solubility of poly(4‐methyl‐o‐phenylenediamine) (P(4Me‐oPD)), poly(4,5‐dimethyl‐o‐phenylenediamine) (P(dMe‐oPD)) and poly(4‐(tert‐butyl)‐o‐phenylenediamine) (P(tBu‐oPD)) polymers was improved compared with the poly(o‐phenylenediamine) (P(oPD)) polymers in most common solvents. The homopolymers obtained were characterized by Fourier transform IR spectroscopy, UV?visible spectroscopy, ¹H and ¹³C NMR, wide‐angle X‐ray diffraction, DSC and TGA. The results showed that the yield, solubility and structure of the polymers are significantly dependent on the polymerization conditions. DSC measurements indicated that the polymers exhibited melting and crystallization transitions. The polymers also showed good thermal stability and decompose above 400 °C in nitrogen. © 2013 Society of Chemical Industry     

Studies of phosphonate‐containing bismaleimide resins. I. Synthesis and characteristics of model compounds and polyaspartimides

Two phosphonate‐containing bismaleimide (BMI) [(4,4′‐bismaleimidophenyl)phosphonate] monomers with different melting temperatures and similar curing temperatures were synthesized by reacting N‐hydroxyphenylmaleimide with two kinds of dichloride‐terminated phosphonic monomers. The BMI monomers synthesized were identified with ¹H‐, ¹³C‐, and ³¹P‐nuclear magnetic resonance (NMR) spectroscopy and elemental analysis. The phosphonate‐containing BMI monomers react with a free‐radical initiator to prepare phosphonate‐containing BMI polymers and also with various aromatic diamines to prepare a series of polyaspartimides as reactive flame retardants. The polymerization degrees of polyaspartimides depend on the alkalinity and nucleophility of diamines as chain extenders. Differential scanning calorimetry (DSC) and thermogravimetry analysis (TGA) were used to study the thermal properties of the phosphonate‐containing BMI resins such as the melting temperature, curing temperature, glass transition temperature (T_g), and thermal resistance. All the phosphonate‐containing BMI resins, except the BMI polymers, have a T_g in the range of 210–256°C and show 5% weight loss temperatures (T_5%) of 329–434 and 310–388°C in air and nitrogen atmospheres, respectively. The higher heat resistance of cured BMI resin relative to the BMI polymer is due to its higher crosslinking density. Since the recrosslinking reactions of BMI polymers and polyaspartimides occur more easily in an oxidation environment, their thermal stabilities in air are higher than are those in nitrogen gas. In addition, the thermal decomposition properties of polyaspartimides depend on the structures and compositions of both the diamine segments and the BMI segments. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 1919–1933, 2002     

Study on microemulsion polymerization of N‐butyl maleimide

By using sodium dodecyl sulfate (SDS) as an emulsifier, polymerization of N‐butyl maleimide (NBMI) was carried out in ternary oil‐in‐water microemulsion, initiated with potassium persulfate (KPS). The kinetics of microemulsion polymerization were measured by dilatometry. The effects of initiator concentration, polymerization temperature, monomer concentration, and emulsifier concentration on polymerization kinetics were investigated. On this basis, the polymerization kinetics were discussed. The experiment result showed that the microemulsion polymerization kinetics of N‐butyl maleimide were almost consistent with the prediction of the Smith‐Ewart theory in conventional emulsion polymerization, except that the emulsifier showed a special effect on polymerization. At the same time, the polymer was characterized by IR, ¹H‐NMR, DSC, and TGA. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 805–809, 2000     

The synthesis of high molecular weight polybutene‐1 catalyzed by Cp★ Ti(OBz)3/MAO

A new stereoregular polybutene‐1 was synthesized with a novel catalyst precursor η⁵‐pentamethyl cyclopentadienyl titanium tribenzyloxide (CpTi(OBz)₃) and methylaluminoxane (MAO). The effects of polymerization conditions on the catalytic activity, molecular weight and stereoregularity of the products were investigated in detail. It was found the catalyst exhibited highest activity of 91.2 kgPB mol Ti⁻¹ h⁻¹ at T = 30 °C, Al/Ti = 200. The catalytic activity and molecular weight were sensitive to the Al/Ti (mole/mole), polymerization temperature; they also depended on the Ti concentration. The molecular weight of the products increased with decreasing temperature. The structure and properties of the polybutene‐1 were characterized by ¹³C NMR, GPC, DSC and WAXD. The result showed the microstructure of polybutene‐1 extracted by boiling heptane was stereoregular, whereas the ether‐soluble fraction was atactic. The molecular weight of polybutene‐1 was over one million g mol⁻¹ and its molecular weight distribution ( M _w/ M _n) was from 1.1 to 1.2. © 2001 Society of Chemical Industry     

Preparation and surface properties of core‐shell polyacrylate latex containing fluorine and silicon in the shell

The core‐shell polyacrylate latex particles containing fluorine and silicon in the shell were successfully synthesized by a seed emulsion polymerization, using methyl methacrylate (MMA) and butyl acrylate (BA) as main monomers, dodecafluoroheptyl methacrylate (DFMA), and γ‐(methacryloxy) propyltrimethoxy silane (KH‐570) as functional monomers. The influence of the amount of fluorine and silicon monomers on the emulsion polymerization process and the surface properties of the latex films were discussed, and the surface free energy of latex films were estimated using two different theoretical models. The emulsion and its films were characterized by particle size distribution (PSD) analysis, transmission electron microscopy (TEM), Fourier transform infrared spectrum (FTIR), nuclear magnetic resonance (¹H‐NMR and ¹⁹F‐NMR) spectrometry, contact angle (CA) and X‐ray photoelectron spectroscopy (XPS), differential scanning calorimetry (DSC), and thermogravimetry (TG) analysis. The results indicate that the average particle size of the latex particles is about 160 nm and the PSD is narrow, the synthesized latex particles exist with core‐shell structure, and a gradient distribution of fluorine and silicon exist in the latex films. In addition, both the hydrophobicity and thermal stability of the latex films are greatly improved because of the enrichment of fluorine and silicon at the film‐air interface, and the surface free energy is as low as 15.4 mN/m, which is comparable to that of polytetrafluoroethylene (PTFE). © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Synthesis of methacrylate copolymers and their effects as pour point depressants for lubricant oil

In this study, polymethacrylate polymers were synthesized by free‐radical polymerization for use as pour point depressants in lubricant oil, and their low‐temperature properties were investigated. Four methacrylate monomers were synthesized by the esterification of methyl methacrylate (MMA) with four kinds of fatty alcohols. The purification step was performed to prepare the pure monomers. Two polymerization experiments were carried out with four kinds of methacrylate monomers obtained previously and MMA. Copolymers, which were made from one kind of monomer and MMA, and terpolymers, which were made from two kinds of monomers and MMA, were prepared. The molecular structures of the synthesized methacrylate monomers and polymethacrylate polymers were verified by ¹H‐NMR, and the molecular weight data were obtained by gel permeation chromatography. The pour points of the base oils containing 0.1 wt % polymethacrylate polymers were measured according to ASTM D 97‐93. The pour points of most base oils containing each polymer decreased compared to that of the pure base oil. Particularly, poly(dodecyl methacrylate‐co‐hexadecyl methacrylate‐co‐methyl methacrylate), made of dodecyl methacrylate, hexadecyl methacrylate, and MMA at a molar ratio of 3.5 : 3.5 : 3, showed the best low‐temperature properties. This terpolymer dropped the pour point of the base oil by as much as 23°C, and its yield was 93.5%. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Inverse emulsion free‐radical polymerization of acrylamide terpolymer for enhanced oil recovery application in harsh reservoir conditions

A free‐radical inverse emulsion polymerization formulation has been developed for preparation of acrylamide (AAm)/sodium 2‐acrylamido‐2‐methylpropanesulfonate (AMPSNa)/N‐vinylpyrrolidone (VP) terpolymers. An aqueous solution of a blend of monomers is emulsified in n‐decane using Tween 85 (Tw85). Ammonium persulfate (APS) and dicumyl peroxide (DCP) were used as initiators for water and oil phases, respectively. The reactions were catalyzed by temperature and by a redox pair; the former is achieved at 60°C and the latter by adding tetramethylethylenediamine (TEMED) and sodium bisulphite (BisNa) to activate the initiator in water and oil phase, respectively. The emulsion type, stability, conversion, and rate of polymerization were analyzed. The obtained terpolymer was characterized by elemental analysis, infrared spectroscopy (FTIR), ¹³C nuclear magnetic resonance (NMR), thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), gel permeation chromatography (GPC), and rheology. Thermal catalyzed emulsion polymerization initiated with DCP showed the best performance as viscosity control agent and as polymeric precursor for in situ gel forming, for water mobility control and flow diversification, respectively. Both application for enhanced oil recovery purposes in harsh oil reservoir conditions are presented. POLYM. ENG. SCI., 57:1214–1223, 2017. © 2017 Society of Plastics Engineers     

Synthesis and characterization of ABA type tri‐block copolymers derived from p‐dioxanone,L‐lactide and poly(ethylene glycol)

A series of triblock co‐polymers, consisting of a poly(ethylene glycol) (PEG) central block joined to two blocks of random p‐dioxanone‐co‐L ‐lactide copolymers were synthesized by ring‐opening polymerization of p‐dioxanone (PDO) and L ‐lactide (LLA) initiated by PEG in the presence of stannous 2‐ethylhexanoate catalyst. The resulting copolymers were characterized by various techniques including ¹H and ¹³C NMR and FTIR spectroscopies, gel permeation chromatography, inherent viscosity, wide‐angle X‐ray diffractometry (WAXD) and differential scanning calorimetry (DSC). The conversion of PDO and L ‐lactide into the polymer was studied various mole ratios and at different polymerization temperature from ¹H NMR spectra. Results of WAXD and DSC showed that the crystallinity of PEG macroinitiator was greatly influenced by the composition of PDO and L ‐lactide in the copolymer. The triblock copolymers with low molecular weight were soluble in water at below room temperature. © 2003 Society of Chemical Industry     

Aromatic triblock polymers from natural sources as protective coatings for stone surfaces

Aromatic triblock polymers were synthesized, characterized, and tested as protective coatings for stone surfaces. Syntheses were carried out by a ring opening polymerization process from specifically synthesized monomers ((3S)‐6‐methyl‐3‐phenyl‐1,4‐dioxan‐2,5‐dione or 1,4‐benzodioxepin‐3‐methyl‐2,5‐dione) and a perfluoropolyether diol (Fluorolink D10‐H), as chain initiator. Polymers were characterized through spectroscopic and analytical techniques while their stability under photo‐oxidative conditions was tested using a Solar Box. An excellent stability to environmental conditions was noticed with very low degradation during accelerated aging tests up to 1000 h, as detected by FTIR, molecular weight, DSC and weight loss. Furthermore, these polymers formed an excellent protective coating on the stone surface as shown by capillary water absorption test. Finally, as expected, very stable coatings were obtained as shown by aging tests. The stone surface showed negligible changes of color and a good hydrorepellency confirming a good durability of treatments. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43377.     

Synthesis,characterization, and gamma radiation effects over well‐defined poly(vinylsiloxanes) copolymers

Anionic ring‐opening polymerization (AROP) was employed for the controlled synthesis of linear model block copolymers of 1,3,5,7‐tetrametil‐1,3,5,7‐tetravinyl(cyclotetrasiloxane) (V₄) and 1,3,5‐dimethyl(cyclotrisiloxane) (D₃) monomers by using sec‐butyl lithium (sec‐Bu^?Li⁺) as initiator, and high‐vacuum anionic polymerization techniques. V₄ copolymerization was promoted by employing D₃ and sec‐Bu^?Li⁺ producing living silanolates that open the stable V₄ ring. For this purpose, two strategies were applied: (a) sequential addition of monomers, and (b) one‐step copolymerization at different reaction temperatures. According to the experimental results, higher levels of V₄ incorporation (～ 18.14 mol %) were obtained by mixing both co‐monomers and performing the reaction at high temperature (80°C). This strategy allowed the control of the V₄ incorporation into the copolymer structure, giving the opportunity of synthesizing model vinyl‐siloxane polymers. The gamma radiation of these materials showed that lower doses are needed to achieve the same gel content as in a model poly(dimethylsiloxane) (PDMS). In such a sense, these results constitute one of the first reports regarding the effect of gamma radiation on vinyl‐containing silicon polymers, and may be of fundamental importance if a biomedical cross‐linked rubber‐type PDMS is needed at earlier doses of sterilization. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Effect of polymerization conditions on o‐phenylenediamine and o‐phenetidine oxidative copolymers

A series of new o‐phenylenediamine (OPD)/o‐phenetidine (PHT) copolymers with partly phenazine‐like structures has been successfully synthesized at three polymerization temperatures by chemically oxidative polymerization in four different polymerization media. The molecular structures and properties of the resulting OPD/PHT polymers were investigated by IR, UV–vis and high‐resolution ¹H NMR spectroscopies, and DSC, in order to ascertain the effect of reaction temperature, comonomer ratio and acid medium. The copolymerization mechanism of OPD with PHT monomers has been proposed. It is found that the statistical OPD/PHT copolymer obtained at a temperature of 118 °C has a higher degree of polymerization than that obtained at 12–17 °C. The OPD content in the copolymers calculated from NMR spectroscopic analysis is higher than that in the feed OPD content, whereas the OPD content calculated from element analysis is slightly lower than the feed OPD content. It can be predicted that denitrogenation takes place in the OPD units during the polymerization process at OPD/PHT molar ratios of 90/10 and 100/0. These OPD/PHT copolymers exhibit a much better solubility than the OPD homopolymer, hence suggesting an incorporation of PHT units into the phenazine structure of the homopolymer. The thermal behavior of the copolymers was also studied. Copyright © 2004 Society of Chemical Industry