Molecularly imprinted electrochemical sensor for the determination of ampicillin based on a gold nanoparticle and multiwalled carbon nanotube‐coated pt electrode

A novel molecularly imprinted electrochemical sensor was developed for the sensitive and selective determination of ampicillin (AMP). The sensor was prepared on a platinum electrode modified with multiwalled carbon nanotubes (MWCNTs), gold nanoparticles (AuNPs), and a thin film of molecularly imprinted polymers (MIPs). MWCNTs and AuNPs were introduced to enhance the sensor's electronic transmission and sensitivity. The molecularly imprinted polymer (MIP) was synthesized using AMP as the template molecule, methacrylic acid as functional monomer, and ethylene glycol maleic rosinate acrylate (EGMRA) as cross‐linker. The performance of the proposed imprinted sensor was investigated using cyclic voltammetry (CV), differential pulse voltammetry (DPV), and electrochemical impedance spectroscopy (EIS). The results showed that the imprinted film displayed a fast and sensitive response to AMP. Under optimal conditions, response peak current had a linear relationship with the concentration of AMP in the range of 1.0 × 10^?8 mol/L to 5.0 × 10^?6 mol/L and a detection limit of 1.0 × 10^?9 mol/L (S/N = 3). This imprinted sensor was used to detect AMP in food samples with recoveries of 91.4–105%. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40613.     

Construction of a novel sensor based on electropolymerization of carmine for voltammetric determination of 4‐nitrophenol

4‐Nitrophenol (4‐NP) has been determined with voltammetric technique based on a novel sensor fabricated by electropolymerization of carmine on a glassy carbon electrode (GCE). An obvious reduction peak located at about ?0.700 V and a couple of redox peaks that were not well‐defined were observed in the potential range of ?1.00 to 0.600 V. Compared with its voltammetric behavior on a bare GCE, the reduction peak potential shifted positively and the peak current increased significantly. All experimental parameters were optimized and linear sweep voltammetry was proposed for its determination. In the optimal conditions, the reduction peak current was proportional to the 4‐NP concentration over the concentration range from 5.00 × 10^?8 to 1.00 × 10^?5 mol L^?1, and the detection limit was 1.00 × 10^?8 mol L^?1 after 200 s of accumulation. The high sensitivity and selectivity of the sensor was demonstrated by its practical application for the determination of trace amounts of 4‐NP in lake water. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 3271–3277, 2007     

Preparation of poly(9‐aminoacridine)‐modified electrode and its application in the determination of dopamine and ascorbic acid simultaneously

A novel modified electrode was fabricated with 9‐aminoacridine by electropolymerization in the phosphate buffer solution (PBS) (pH 7.4) and was characterized by cyclic voltammetry (CV). The modified electrode showed excellent electrocatalytic effect and high stability toward the electrochemical oxidation of dopamine (DA) and ascorbic acid (AA). Also, it showed a high stability for the determination of DA and AA simultaneously. Well‐separated voltammetric peaks were observed for DA and AA on the modified electrode. The separation of two anodic peaks was 170 mV, which was large enough to eliminate the interference of AA and determine DA. The differential pulse voltammograms (DPV) were used for the measurement of DA by means of the poly(9‐aminoacridine)‐modified electrode in PBS at pH 7.4. A linear response toDA was observed in the concentration range from 1.5 × 10^?6 to 3.5 × 10^?3 mol L^?1 with a correlation coefficient of 0.9998 and a detection limit (S/N = 3) of 1.0 × 10^?7mol L^?1. The proposed method was used to determine DA in DA‐hydrochloride injection and showed excellent sensitivity and recovery. The ease of fabrication, good reproducibility, high stability, and low cost of the modified electrode are the promising features of the proposed sensor. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 3864–3870, 2007     

Preparation of block copolymers via metal‐free visible‐light‐induced ATRP for the detection of lead ions

Polyacrylamide‐b‐poly(methacrylic acid) was prepared on the surface of Au electrode (Au/PAM/PMAA) for Pb²⁺ ion electrochemical sensing via metal‐free visible‐light‐induced atom transfer radical polymerization, which was very simple, convenient, and environmentally friendly. Au/PAM/PMAA was carefully examined by cyclic voltammetry, electrochemical impedance spectroscopy, and X‐ray photoelectron spectroscopy. Further, Au/PAM/PMAA was successfully used for the determination of Pb²⁺ ion by differential pulse anodic stripping voltammetry. Under the optimal conditions, a linear response from 1.0 × 10^?11 to 1.0 × 10^?4 mol/L with detection limit of 2.5 × 10^?12 mol/L (S/N = 3) was achieved from the results of experiments. Comparing with similar Pb²⁺ sensors, the broader linear range and lower detection limit suggested the promising prospect of Au/PAM/PMAA. In a word, the work of this article had an important significance for the polymer‐modified electrodes and the sensitive detection of Pb²⁺. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45863.     

m‐Chloroaniline emulsion polymerization,macromolecular chain structure and electrochemical properties

Poly(m‐chloroaniline) (PmClAn) was synthesized by emulsion polymerization. The influences of reaction temperature and initiator concentration on polymerizations were studied. It was found that PmClAn with number‐average molecular weight of 1.85 × 10³ g mol^?1 was obtained by the following conditions: 80 °C, [monomer] = 0.187 × 10^?3 mol l^?1, [sodium lauryl sulfate] = 4.8 × 10^?2 mol l^?1, [potassium peroxydisulfate] = 5.6 × 10^?2 mol l^?1, reaction period = 2.0 h. ¹H NMR, FTIR, and transmission and scanning microscopy were used for structural characterization of PmClAn. It was shown that the ratio of benzoid to quinoid units in the macromolecular chain was respectively 3:2, and that PmClAn has a typical crystalline monoclinic form. A PmClAn molecular chain configuration was also proposed on the basis of crystallographic data. Cyclic voltammetry experiments revealed the PmClAn membrane electrode electroactivity. This electroactivity increased when the polymer was proton‐doped. When Pt particles were electrodeposited onto the polymer membrane electrode, they presented a preferred orientation. Isopropanol oxidation intensities with platinized PmClAn modified electrodes were larger than with a platinized Pt electrode. We also found that oxidation occurred mainly on the Pt particles deposited on the polymer, and that the anodic peak potential changed with polymer and its doping level. These results indicated that the Pt particles interacted with the polymer and that catalytic properties could be observed. © 2002 Society of Chemical Industry     

A Novel Amperometric Sensor for Salicylic Acid Based on Molecularly Imprinted Polymer-Modified Electrodes

A novel electrochemical MIP-sensor for salicylic acid (SA) has been synthesized firstly by electropolymerizing o-phenylenediamine on glassy carbon electrode in presence of template molecule (salicylic acid). The response of the sensor to SA is investigated by square wave voltammetry (SWV). The linearity is obtained over a concentration range of 6 × 10^?5 ～ 1 × 10^?4 mol/L (R² = 0.9961). And the detection limit of SA is about 2 × 10^?5 mol/L. The sensor exhibits good selectivity for salicylic acid by virtue of the interaction between molecularly imprinted binding sites and the template.     

Electrochemical preparation of poly(N‐acetylaniline)/poly‐(4‐styrenesulfonic acid‐co‐maleic acid) composite film towards ascorbic acid sensing

Poly(N‐acetylaniline)/poly(4‐styrenesulfonic acid‐co‐maleic acid) (PNAANI/PSSMA) composite film was prepared by cyclic voltammetry (CV), and was characterized by FTIR and X‐ray photoelectron spectrum (XPS). The electroactivity of the composite film was high in neutral and basic solutions, and it had been used for amperometric determination of ascorbic acid (AA). Compared with pure PNAANI film, the catalytic activity of the composite film was much better. AA was detected amperometrically in sodium citrate buffer at a potential of 0.3 V (versus SCE). The response current was proportional to the concentration of ascorbic acid in the range of 4.7 × 10^?6 to 5.0 × 10^?5M and 5.0 × 10^?5 to 2.5 × 10^?3M, respectively, with the detection limit of 1.9 × 10^?6 mol L^?1 at a signal to noise ratio 3. In addition, the stability and reusability of the composite film were performed well, and it was satisfying to be used for determination of AA in real fruit juice samples. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Determination of Sodium Dodecyl Sulfate in Toothpastes by a PVC Matrix Membrane Sensor

The construction and characteristic performance of a new potentiometric PVC membrane sensor responsive for sodium dodecyl sulfate (SDS) are described. The sensor is based on the use of cetyltrimethylammonium‐tetraphenylborate (CTA‐TPB) ion‐pair complex as electroactive material in PVC matrix in presence of dioctyl phthalate as a solvent mediator. The sensor exhibits a rapid, stable and near‐Nernstian response for SDS over the concentration range of 5 × 10^?3–5 × 10^?6 mol dm^?3 at 25 ± 2 °C and the pH range 4–8.5 with slope of 59.6 mV/decade change in SDS concentration. The lower detection limit is 5 × 10^?6 mol dm^?3 and the response time is 45 s. The determination of selectivity coefficients for different anions shows there is no interference except that of dodecyl benzene sulfonate (DBS^?) ion which has a strong interference. The results obtained in the determination of SDS in toothpastes, using this sensor as an indicator electrode, were compared with those obtained from the spectrophotometric method using methylene blue as the reagent.     

Gold nanoparticle ensemble on polydopamine/graphene nanohybrid as a novel electrocatalyst for determination of baicalein

A facile and green approach is used to synthesize polydopamine (PDA) functionalized reduced graphene oxide (RGO) via the self‐polymerization of dopamine (DA) under alkaline conditions. The obtained reduced RGO/PDA composite facilitate Au precursor adsorption. Then Au nanoparticles are reduced and assemble onto the surface of RGO/PDA composite form reduced RGO/PDA/gold (RGO/PDA/Au) nanocatalysts. After that, a sensitive electrochemical sensor for baicalein is fabricated based on RGO/PDA/Au nanocatalysts. In this method, the hydroxyl units of PDA can form hydrogen bonding with the phenolic hydroxyl groups of baicalein, making baicalein easily adsorb on the modified electrode surface to enhance the electrochemical response. The electrochemical mechanism of baicalein on the RGO/PDA/Au nanocatalysts modified GCE is thoroughly investigated by cyclic voltammetry. The fabricated electrochemical sensor show good electrochemical activity for baicalein. The linear range of baicalein is 1 × 10^?8 to 15 × 10^?6 mol L^?1 with the detection limit of 3.1 × 10^?9 mol L^?1. Furthermore, the proposed electrochemical sensor can be used to detect real sample. The results reveal that this method provides a new avenue for electrochemical investigation of baicalein in biochemical, pharmaceutical, and clinical research. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 46720.     

Modification of dextran through the grafting of N‐vinyl‐2‐pyrrolidone and studies of physicochemical phenomena in terms of metal‐ion uptake,swelling capacity,and flocculation

The optimum conditions for grafting N‐vinyl‐2‐pyrrolidone onto dextran initiated by a peroxydiphosphate/thiourea redox system were determined through the variation of the concentrations of N‐vinyl‐2‐pyrrolidone, hydrogen ion, potassium peroxydiphosphate, thiourea, and dextran along with the time and temperature. The grafting ratio increased as the concentration of N‐vinyl‐2‐pyrrolidone increased and reached the maximum value at 24 × 10^?2 mol/dm³. Similarly, when the concentration of hydrogen ion increased, the grafting parameters increased from 3 × 10^?3 to 5 × 10^?3 mol/dm³ and attained the maximum value at 5 × 10^?3 mol/dm³. The grafting ratio, add‐on, and efficiency increased continuously with the concentration of peroxydiphosphate increasing from 0.8 × 10^?2 to 2.4 × 10^?2 mol/dm³. When the concentration of thiourea increased from 0.4 × 10^?2 to 2.0 × 10^?2 mol/dm³, the grafting ratio attained the maximum value at 1.2 × 10^?2 mol/dm³. The grafting parameters decreased continuously as the concentration of dextran increased from 0.6 to 1.4 g/dm³. An attempt was made to study some physicochemical properties in terms of metal‐ion sorption, swelling, and flocculation. Dextran‐g‐N‐vinyl‐2‐pyrrolidone was characterized with infrared spectroscopy and thermogravimetric analysis. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

One pot synthesis of xanthan gum‐g‐N‐vinyl‐2‐pyrrolidone and study of their metal ion sorption behavior and water swelling property

In this article, graft copolymerization of N‐vinyl‐2‐pyrrolidone onto xanthan gum initiated by potassium peroxydiphosphate/Ag⁺ system in an aqueous medium has been studied under oxygen free nitrogen atmosphere. Grafting ratio, grafting efficiency, and add on increase on increasing the concentration of potassium peroxydiphosphate (2.0 × 10^?3 to 12 × 10^?3 mol dm^?3), Ag⁺(0.4 × 10^?3 to 2.8 × 10^?3 mol dm^?3), and hydrogen ion concentration from 2 × 10^?3 to 14.0 × 10^?3 mol dm^?3. Maximum grafting has been obtained when xanthan gum and monomer concentration were 0.4 g dm^?3 and 16 × 10^?2 mol dm^?3, respectively, at 35°C and 120 min. Water swelling capacity, swelling ratio, metal ion uptake, and metal retention capacity have also been studied, and it has been found that graft copolymer shows enhancement in these properties than pure xanthan gum. The graft copolymer has been characterized by FTIR and thermal analysis. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Electroreduction of hexavalent chromium by polyaniline

BACKGROUND: A plate‐gap model interpretation of enzymatic reaction kinetics and rotating disc voltammetry were applied for evaluation of the nature of the reaction of the electroreduction of Cr(VI) (as dichromate ions) on a polyaniline (PANI)‐modified glassy carbon (GC) electrode. RESULTS: The kinetic parameters (the maximal current (V_max) and Michaelis constant (K_M)) for electroreduction of Cr(VI) on the PANI‐modified GC electrode were determined as V_max = 0.34 × 10^?7 mol cm^?3 s^?1 and K_M = 0.47 × 10^?6 mol cm^?3. The reduction of dichromate is intensified by PANI film growth. CONCLUSION: To characterise the electroreduction of Cr(VI) on a PANI‐modified GC electrode, the kinetic parameters of the reaction were determined using a plate–gap model interpretation of enzymatic reaction kinetics and rotating disc voltammetry. The catalytic nature of Cr(VI) electroreduction on the PANI‐modified electrode has been shown. Copyright © 2009 Society of Chemical Industry     

Electropreparation of (±)‐10‐camphorsulfonate‐doped poly(o‐phenylenediamine) in acetonitrile and its use in determination of glucose

Poly(o‐phenylenediamine) (PoPD) film has been electrochemically prepared on Pt electrode in an acetonitrile–water medium containing o‐phenylenediamine (oPD) monomer and (±)‐10‐camphorsulfonic acid (HCSA) by using the cyclic voltammetry (CV). The PoPD film (PoPD–CSA) has been characterized by FTIR, CV, EIS, FESEM, and conductivity measurement. The glucose biosensor (Pt/PoPD–CSA/GOx) has been prepared from the PoPD coated electrode by immobilizing glucose oxidase (GOx) enzyme using glutaraldehyde. The biosensor shows a low detection limit and wide linear working range, a good reusability, long‐term stability, and anti‐interference ability. The Pt/PoPD–CSA/GOx has possesses higher sensitivity (2.05 μA/mmol L^?1) and affinity to glucose due to the use of CSA ion as dopant. The linear concentration ranges of Pt/PoPD–CSA/GOx have been found to be 9.6 × 10^?3 to 8.2 mmol L^?1 from calibration curve and 4.6 × 10^?2 to 100 mmol L^?1 from the relationship between the (1/glucose concentration) and (1/current difference). © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39864.     

A study toward the physicochemical properties of graft copolymer (partially carboxymethylated guar gum‐g‐N,N′‐dimethylacrylamide): Synthesis and characterization

Unreported graft copolymer of N,N′‐dimethylacrylamide (DMA) with partially carboxymethylated guar gum (CmgOH) has been synthesized and the reaction conditions have been optimized for affording maximum grafting using a potassium peroxymonosulphate (PMS)/thiourea (TU) redox initiators under nitrogen atmosphere. The study of graft copolymerization has been performed to observe maximum value of grafting parameters except percentage of homopolymer by varying the concentrations of DMA, PMS, and TU. The grafting parameters increase continuously on increasing the concentration of DMA from 8 × 10^?2 to 24 × 10^?2 mol dm^?3, PMS from 5 × 10^?3 to 21 × 10^?3 mol dm^?3, and TU from 1.6 × 10^?3 to 4.8 × 10^?3 mol dm^?3. The optimum temperature and time for grafting of DMA onto CmgOH were found to be 35°C and 120 min, respectively. The water‐swelling capacity of graft copolymer is investigated. Flocculation property for both coking and noncoking coals is studied for the treatment of coal mine waste water. The graft copolymer is characterized by Fourier transform infrared spectroscopy and thermogravimetric analysis. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Synthesis and photophysical behavior of a water‐soluble coumarin‐bearing polymer for proton and Ni2+ ion sensing

BACKGROUND: In recent years, many fluorescent chemosensors with various macromolecular structures have been prepared for the detection of protons or metal cations in the environment. Most of this research is focused on polymer sensors with fluorescent recognition sites in the main chain. In this case, the fluorescent recognition sites are covalently bonded to the polymer chain, and thus the polymer shows photophysical properties as a chemosensor for protons and metal ions. RESULTS: An acrylic monomer bearing coumarin moieties, 7‐hydroxy‐4‐methyl‐8‐(4′‐acryloylpiperazin‐1′‐yl)methylcoumarin, was synthesized. This was then copolymerized with N‐vinylpyrrolidone to obtain a blue fluorescent material. The fluorescent copolymer has good solubility in aqueous solution. Its main photophysical properties were determined in relation to its use as a sensor for protons and metal cations. It is an efficient ‘off‐on’ switcher for pH between 3.02 and 12.08. Additionally, the polymer sensor is selective to Ni²⁺ ions, with the increase in the fluorescence intensity depending on Ni²⁺ ion concentrations in the range 0.33 × 10^?5–7.67 × 10^?5 mol L^?1. CONCLUSION: The results suggest that this copolymer may offer potential as a reusable polymer sensor for protons and Ni²⁺ ions in aqueous solution. Copyright © 2009 Society of Chemical Industry     

Facile synthesis of graphene/polypyrrole 3D composite for a high‐sensitivity non‐enzymatic dopamine detection

One kind of nanocomposite consisting of graphene and polypyrrole was synthesized via a facile and mild way with the assistant of microwave irradiation. The synthesis route was embedding the polypyrrole into the graphene flakes to form a 3D structure, to achieve larger active surface and higher electro‐catalysis property. Structures and components of the composite were measured by X‐ray diffraction, field emission scanning electron microscopy, and Fourier transform infrared spectroscopy. A stronger electrochemical response of electrode with modified resultant was observed in the electrochemical test. Dopamine sensor based on the composite showed a sensitivity of 363 μA mM ^?1 cm^?2, a linear range of 1 × 10^?4 M to 1 × 10^?3 M , and a detection limit of 2.3 × 10^?6 M (S/N = 3). © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134 , 44840.     

Zinc ion-imprinted polymer based on silica particles modified carbon paste electrodes for highly selective electrochemical determination of zinc ions

ABSTRACT

In this study, Zn(II) ion-imprinted polymer was prepared on the surface of vinyl silica particles and applied for detection of Zn(II) ions using differential pulse voltametry. The ion- imprinted polymer particles were prepared by free radical polymerization. The prepared particles were characterized by different morphological and elemental techniques. The ion-imprinted particles were used to fabricate the carbon paste electrode as a zinc ions sensor. The modified zinc sensor showed linear response in the concentration range 6.12 × 10^?9 to 4.59 × 10^?8 mol L^?1. The limit of detection and limit of quantification of the electrode were 1.351 × 10^?8 and 4.094 × 10^?8 mol L^?1, respectively.     

Electrochemical synthesis and characterization of new electrodes based on poly‐hematoxylin films

The poly‐hematoxylin films undoped (p‐HX) and doped with strontium (p‐HX‐Sr) were prepared on the platinum electrodes (Pt) using cyclic voltammetry. The influence of experimental parameters, such as: anodic potential and number of voltammetric cycles on the films synthesis was investigated by electrochemical impedance spectroscopy (EIS). The results showed that, the optimal conditions to obtain the poly‐hematoxylin films on platinum electrode from 10^?2 mol L^?1 NaNO₃ solution, were found by recording 10 voltammetric cycles at an anodic potential of 1.5 V. Electrocatalytic activity of the poly‐hematoxylin‐platinum (p‐HX/Pt) and poly‐hematoxylin‐strontium‐platinum (p‐HX‐Sr/Pt) electrodes was tested for electrochemical degradation of benzocaine using UV‐Vis spectrophotometry. Both, the mechanisms of hematoxylin (HX) polymerization, as well as benzocaine degradation were proposed. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Development of a new two‐enzyme biosensor based on poly(pyrrole‐co‐3,4‐ethylenedioxythiophene) for lactose determination in milk

A new lactose biosensor was developed by preparing a suitable copolymer of polypyrrole and poly(3,4‐ethylenedioxythiophene) synthesized using the electropolymerization method. Pyrrole and 3,4‐ethylenedioxythiophene monomers were deposited in the presence of sodium dodecylbenzene sulphonic acid on a platinum disc electrode, which was used as the working electrode. The sensor is based on the serial reactions of β‐galactosidase and galactose oxidase immobilized on a copolymer‐modified platinum disc electrode. Successful synthesis of the enzyme‐immobilized copolymer was confirmed by FT‐IR spectrometry, SEM, and electrochemical analysis. The response of the enzyme electrode to lactose was determined by cyclic voltammetry at + 0.40 V. The response time of the biosensor was found to be from 8 to 10 s, and the upper limit of the linear working portion was found to be at a lactose concentration of 2.30 mM with a detection limit of 1.4 × 10^?5 M. The apparent Michaelis–Menten constant was found to be 0.65 mM of lactose. The effects of interferents were also investigated. Lactose concentrations determined by the biosensor were in good agreement with those measured by the reference methods. Our results show that the developed biosensor has a significant potential to the determination of lactose concentration in milk. POLYM. ENG. SCI., 58:839–848, 2018. © 2017 Society of Plastics Engineers     

Development of a voltammetric sensor based on a molecularly imprinted polymer (MIP) for caffeine measurement

A new voltammetric sensor for caffeine measurement is introduced. A caffeine-selective molecularly imprinted polymer (MIP) and a non-imprinted polymer (NIP) were synthesized and then used for carbon paste (CP) electrode preparation. The MIP, embedded in the carbon paste electrode, functioned as a selective recognition element and a pre-concentrator agent for caffeine determination. The prepared electrode was used for caffeine measurement via a three-step procedure including analyte extraction in the electrode, electrode washing and electrochemical measurement of caffeine. The MIP-CP electrode showed very high recognition ability in comparison to NIP-CP. It was shown that electrode washing after caffeine extraction led to enhanced selectivity. Differential pulse voltammetry for caffeine determination was more effective than square wave voltammetry. Some parameters affecting sensor response were optimized, and a calibration curve was then plotted. A linear range of 6 × 10⁻⁸ to 2.5 × 10⁻⁵ mol L⁻¹ was obtained. The detection limit of the sensor was calculated to be equal to 1.5 × 10⁻⁸ mol L⁻¹. This sensor was used successfully for caffeine determination in spiked beverage and tea samples.