Mechanical properties of a cryogenically mechanically alloyed polycarbonate–poly(aryl ether ether ketone) system

The processing–property relationship of a model cryogenically mechanically alloyed polymer–polymer system [polycarbonate (PC) and poly(aryl ether ether ketone) (PEEK)] was investigated. PC and PEEK powders were cryogenically mechanically alloyed for 10 h, and the resulting two‐phase powder particles were processed into testable coupons with a miniature ram‐injection molder. The bulk mechanical properties of the coupons made from the mechanically alloyed powders and nonmechanically alloyed powders were investigated as a function of mechanical alloying and injection‐molding parameters. The injection‐molded coupons were mechanically tested in the three‐point‐bending mode. The results demonstrated that no measurable improvement was achieved in the energy to break, strain at failure, or failure strength in the coupons made from the mechanically alloyed materials in comparison with those of the coupons made from the nonmechanically alloyed powders. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 1196–1202, 2003     

Thermal properties of melt‐blended poly(ether ether ketone) and poly(ether imide)

The thermal properties of blends of poly(ether ether ketone) (PEEK) and poly(ether imide) (PEI) prepared by screw extrusion were investigated by differential scanning calorimetry. From the thermal analysis of amorphous PEEK–PEI blends which were obtained by quenching in liquid nitrogen, a single glass transition temperature (T_g) and negative excess heat capacities of mixing were observed with the blend composition. These results indicate that there is a favorable interaction between the PEEK and PEI in the blends and that there is miscibility between the two components. From the Lu and Weiss equation and a modified equation from this work, the polymer–polymer interaction parameter (χ₁₂) of the amorphous PEEK–PEI blends was calculated and found to range from −0.058 to −0.196 for the extruded blends with the compositions. The χ₁₂ values calculated from this work appear to be lower than the χ₁₂ values calculated from the Lu and Weiss equation. The χ₁₂ values calculated from the T_g method both ways decreased with increase of the PEI weight fraction. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 72: 733–739, 1999     

Hollow fiber microfiltration membranes from poly(ether ether ketone) (PEEK)

A procedure for obtaining high performance large internal diameter (ID; >1 mm) hollow fiber microfiltration membranes from poly(ether ether ketone) (PEEK) is presented. A simple mixture of isomers of diphenylphthalate is a good solvent for employing the thermal‐phase inversion process to obtain PEEK membranes. Obtaining large ID hollow fibers with substantial transmembrane flux requires sufficient melt strength during spinning to prevent excessive draw of the extruding fiber. The use of a second leachable polymer to the blend satisfies the conditions, and polysulphone (PS) is found to provide superior membranes relative to either poly(etherimide) (PEI) or poly(ether sulphone) (PES) as a second polymer. PEEK membranes obtained by this process yield better chemical resistance to a concentrated warm surfactant/oil solution. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 72: 175–181, 1999     

Poly(ether ether ketone)/poly(aryl ether sulfone) blends: Relationships between morphology and mechanical properties

Mechanical properties such as the tensile modulus, yield (break) strength, and elongation to break (or yield) are measured for multiphase poly(ether ether ketone) (PEEK)/poly(aryl ether sulfone) (PES) blends. Specimens with three different levels of thermal histories (quenched, as‐molded, and annealed) are prepared in order to study their effects on the mechanical properties of PEEK/PES blends. Synergistic behavior is observed in the tensile modulus and tensile strength of the blends in almost the whole range of compositions. The ductility of quenched blends measured as the elongation to break (yield) shows an unexpected synergistic behavior in the blend containing 90 wt % PEEK, although a negative deviation from additive behavior is observed in the rest of the compositions. A ductile–brittle transition is observed between 50 and 75 wt % PEEK in the blend. The ductile–brittle transition in as‐molded blends shifts to 75–90 wt % PEEK. Annealed blends show predominantly brittle behavior in the whole composition range. The experimental data are further correlated with the theoretically predicted results based on various composite models. Although the prediction based on these equations fails to fit the experimental data in the whole composition range, the simplex equations that are normally used for blends showing synergistic behavior produced a reasonable fit to the experimental data. The mechanical properties obtained for different blend compositions are further correlated with their morphology as observed by scanning electron microscopy. Morphological observation shows a two‐phase morphology in PES‐rich blends, which is an interlocked morphology in which the disperse phase is not clearly visible in PEEK‐rich blends, and a cocontinuous type of morphology for a 50/50 composition. Considerable permanent deformation of both the disperse and matrix phase, especially in the case of quenched tensile specimens, demonstrates the remarkable adhesion present between the two phases. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 2887–2905, 2003     

聚醚醚酮共混改性研究进展

综述了聚醚醚酮（PEEK）、聚醚酰亚胺（PEI）、聚四氟乙烯（PTFE）、热致液晶（TLCP）和聚醚砜（PES）等高性能工程塑料的共混改性研究进展,详细探讨了各种PEEK共混物的相容性、结晶行为、微观结构、热行为和力学性能等性能特征。PEEK与PEI在熔融和无定形状态下完全相容,常用于PEEK的结晶行为和微观结构的基础研究;与PTFE、TLCP、PES共混分别是提高PEEK的摩擦磨损性能、加工性能和热稳定性的有效手段。各种共混物的相容性好坏对其结晶行为和微观结构有重要影响,从而影响了共混物的力学性能。在此基础上,对PEEK共混改性领域进一步的研究方向和内容进行了讨论。     

Spherulitic growth kinetics in miscible blends of poly(ether ether ketone) and poly(ether imide)

Growths of poly(ether ether ketone) (PEEK) spherulites from both pure melt and its miscible blends with poly(ether imide) (PEI) have been studied by polarized optical microscopy. The nucleation density of PEEK spherulites was depressed upon blending with PEI, which can be attributed to the reduction in degree of supercooling arising from equilibrium melting point depression. A modified Lauritzen-Hoffman (L-H) theory was adopted to analyze the growth kinetics. Regime III-II transition was observed with the transition temperature decreasing with increasing PEI composition. Assuming free rotations of the virtual bonds in PEEK molecule, the side surface free energy of 12.0 erg/cm² was calculated from the characteristic ratio. The fold surface free energy of 188 erg/cm² and work of chain folding of 12.3 kcal/mol were then obtained from the modified L-H analysis.     

Structural and mechanical characterization of poly(ether ether ketone) (PEEK) and sulfonated PEEK films: Effects of thermal history,sulfonation, and preparation conditions

In this work, virgin and sulfonated poly(ether ether ketone) films (PEEK and SPEEK, respectively) have been studied by dynamic mechanical analysis, modulated differential scanning calorimetry, wide‐angle X‐ray diffraction, birefringence, and optical microscopy. The properties of the unmodified polymer have been addressed to assess the original morphological characteristics and the changes induced by sulfonation. In general, the introduction of ionic groups in the polymer backbone alters dramatically the intrinsic properties of the parent material. The particular thermomechanical response exhibited by PEEK and SPEEK samples, characterized by a hysteresis loop, can be explained by the reversible and irreversible relaxation–orientation of the microstructure, even in the sub‐T_g region. The results showed that the preparation conditions largely determine the nonequilibrium morphological features of both compression‐molded PEEK films and solvent‐cast SPEEK membranes. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 756–774, 2006     

Effect of dihydroxydiphenyl ether on poly(ether ether ketone)

A series of modified poly(ether ether ketone) (PEEK) polymers were synthesized by introduction of addition ether groups from dihydroxydiphenyl ether (DHDE) into the PEEK structure. The inherent viscosity of the DHDE-modified PEEK increased with reaction time at 320 °C. DSC thermograms showed the melting points of the obtained PEEK decreased with the increase of the DHDE content in the backbone. The degradation temperature (T_d) was slightly decreased by the introduction of DHDE. The crystallinity as measured via the X-ray diffraction (XRD) increases with the introduction of DHDE into the modified PEEK. The crystalline structure was identified as an orthorhombic structure with lattice constants a = 7.72 Å, b = 5.86 Å, and c = 10.24 Å. Due to the glass transition temperature (T_g) and the melting temperature (T_m) decreasing with the increase of the DHDE content in the reaction system. the processability of the resultant PEEK could be improved through this DHDE modification.     

Crystallization behavior and mechanical properties of poly(aryl ether ether ketone)/poly(ether imide) blends

Crystallinity and mechanical properties of blends with different amounts of semicrystalline poly(aryl/ ether ether ketone) (PEEK) and amorphous poly(ether imide) (PEI) polymers have been studied. The blends, prepared by melt mixing, have been investigated by differential scanning calorimeter (DSC) to analyze the miscibility between the components and the final crystalline content. Moreover, for the 20/80 PEEK/PEI blend, crystallization in dynamic and isothermal conditions has been carefully investigated in order to find proper conditions for maximum development of crystallinity. Mechanical tests (static and dynamic) have been performed to evaluate the properties of the as-molded and crystallized blends and to compare them with those of crystalline PEEK and amorphous PEI neat resins. Finally, a few SEM observations have been performed to compare the fractured surface of the blend with those of the pure constituents.     

Synthesis and properties of thio‐containing poly(ether ether ketone)s

A series of thio‐containing poly(ether ether ketone) (PEESK) polymers was synthesized by the introduction of thio groups from 4,4′ thiodiphenol (TDP) into the poly(ether ether ketone) (PEEK) structure via reaction between the phenol and aromatic fluoride groups. The effect of the thio groups on the properties of the PEESK materials was investigated. Differential scanning calorimetry (DSC) analysis and X‐ray diffraction (XRD) patterns show a depression in the crystallinity of the PEESKs with incorporation of the content of thio groups in the backbones. The crystalline structure was identified as an orthorhombic structure with lattice constants of a = 7.52 Å, b = 5.86 Å and c = 10.24 Å for all crystallizable PEESKs. The crystalline structures of the thio‐containing PEEK polymers were the same as that of the neat PEEK, which means the thio‐containing block in the whole thio‐containing PEEK molecule is almost excluded from the crystalline structure and the crystals are completely formed by ‘non‐thio’ blocks only. Due to the glass transition temperature (T_g) and melting temperature (T_m) depression with increase in the TDP content in the reaction system, the processability of the resultant thio‐containing PEEKs could be effectively improved. Copyright © 2004 Society of Chemical Industry     

聚苯酯对聚醚醚酮结晶行为的影响

用模压法制备了聚苯酯(Ekonol)／聚醚醚酮(PEEK)复合材料，通过X射线衍射(XRD)、差示扫描量热分析(DSC)考察了PEEK的结晶行为，并测定了复合材料的熔点、结晶温度和玻璃化转变温度。结果表明：Ekonol含量的大小对PEEK的结晶行为产生了直接影响，PEEK的相对结晶度随着Ekonol含量的增加而提高；Ekonol含量小于30％时，对复合材料的熔点、结晶温度和玻璃化转变温度影响不大，但含量大于30％时，材料的结晶温度、熔融温度下降，玻璃化转变温度提高。     

Effect of nano‐barium titanate on the mechanical,electrical and solubility performance of ferrite‐filled poly(ether ether ketone) composites

Ferrite and nano‐barium titanate reinforced poly(ether ether ketone) (PEEK) composites were made by compression moulding technology. The effects of reinforcement of the ferrite and nano‐barium titanate on the PEEK matrix were studied with the aim assessing its potential as a radar‐absorbing structural material (RASM). With an increase in the percentage filling of ferrite in the PEEK matrix, the specific gravity, hardness, tensile and flexural moduli, brittleness, dielectric constant, loss tangent and reflection losses were increased, while the tensile and flexural strengths, and elongation at break, were decreased. With increasing nano‐barium titanate reinforcement in the ferrite‐filled PEEK composites, the specific gravity, hardness, tensile and flexural strengths, tensile modulus and dielectric constant were comparatively increased, while the elongation at break, flexural modulus and loss tangent (marginally) were decreased. Reinforcement of the nano‐barium titanate caused a comparatively marginal reduction in the loss tangent, although no effect on reflection losses was observed. The solubility resistance of the ferrite‐filled PEEK composites was improved with reinforcement by the nano‐barium titanate. Copyright © 2004 Society of Chemical Industry     

Miscibility and mechanical properties of poly(ether imide)/poly(ether ether ketone)/liquid crystalline polymer ternary blends

This paper is concerned with a novel ternary blend composed of poly(ether imide) (PEI), poly(ether ether ketone) (PEEK) and a liquid crystalline polymer (LCP; HX4000, Du Pont). Different compositions were prepared by extrusion and injection moulding. Dynamic mechanical thermal analysis and the observation of the fracture surfaces, before and after annealing, allowed determination of the cold crystallization temperatures and miscibility behaviour of these systems. PEEK/PEI blends are known from previous studies to be miscible at all compositions. In this case it was observed that the PEEK/HX4000 blend was miscible up to 50 wt% HX4000 but partially miscible above this value. The PEI/HX4000 blends were found to be partially miscible in the whole concentration range. As a result, some ternary blend compositions exhibited only one phase, while others exhibited two phases. The measurement of the tensile properties showed that ternary blends with high modulus can be obtained at high LCP loadings, while compositions with high ultimate tensile strength can be obtained with high loadings of PEI or PEEK.     

Crystallization and melting behavior of poly(ether ether ketone)/poly(aryl ether sulfone) blends

The crystallization and melting behavior of poly(ether ether ketone) (PEEK) in blends with poly(aryl ether sulfone) (PES) prepared by melt mixing are investigated by differential scanning calorimetry (DSC) and wide‐angle X‐ray scattering (WAXS). The presence of PES is found to have a notable influence on the crystallization behavior of PEEK, especially when present in low concentrations in the PEEK/PES blends. The PEEK crystallization kinetics is retarded in the presence of PES from the melt and in the rubbery state. An analysis of the melt crystallization exotherm shows a slower rate of nucleation and a wider crystallite size distribution of PEEK in the presence of PES, except at low concentrations of PES, where, because of higher miscibility and the tendency of PES to form ordered structures under suitable conditions, a significantly opposite result is observed. The cold crystallization temperature of the blends at low PES concentration is higher then that of pure PEEK, whereas at a higher PES concentration little change is observed. In addition, the decrease in heat of cold crystallization and melting, which is more prevalent in PEEK‐rich compositions than in pure PEEK, shows the reduction in the degree of crystallinity because of the dilution effect of PES. Isothermal cold crystallization studies show that the cold crystallization from the amorphous glass occurs in two stages, corresponding to the mobilization of the PEEK‐rich and PES‐rich phases. The slower rate of crystallization of the PEEK‐rich phase, even in compositions where a pure PEEK phase is observed, indicates that the presence of the immobile PES‐rich phase has a constraining influence on the crystallization of the PEEK‐rich phase, possibly because of the distribution of individual PEEK chains across the two phases. The various crystallization parameters obtained from WAXS analysis show that the basic crystal structure of PEEK remains unaffected in the blend. Further, the slight melting point depression of PEEK at low concentrations of PES, apart from several other morphological reasons, may be due to some specific interactions between the component homopolymers. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 2906–2918, 2003     

Processing,microstructure, and failure behavior in short-fiber-reinforced poly(ether ether ketone) composites

Short-fiber-reinforced poly(ether ether ketone) (PEEK) composites were prepared by a specially designed mold. Both compression- and extrusion-molded plaques were obtained under the same thermal history. The fiber length distribution, fiber volume fraction, and fiber orientation are characterized. The fibers show an in-plane random orientation in compression-molded plaques, but they exhibit a 3-layer fiber orientation well-known for injection moldings in extrusion-molded composites. It is the final aim to simulate the rheological and morphologic behavior in injection moldings by using the laboratory designed extrusion/compression mold. Static compact tension (CT) specimens and electron microscopy (EM) were used to investigate the failure behavior. Results showed that crack initiation is the dominant failure energy absorption process in a brittle fracture, whereas crack propagation is dominant in a ductile failure. The extruded composites were mechanically characterized in two orthogonal directions (T- and L-type). The anisotropy factor is reported as 1.2.     

Compatibility in immiscible poly(ether ether ketone)/poly(ether sulfone) blends

Both as-molded and annealed poly(ether ether ketone) (PEEK)/poly(ether sulfone) (PES) blends have been prepared by direct injection molding. The system has been found to be immiscible at all compositions; however, as a result mainly of the produced morphology, it surprisingly maintains to a very great extent the excellent mechanical performance of both of the pure components. This mechanical response is compared with that of the compression molded blends. The ductility of these blends when quenched appears close to the linear between that of the two components. Leaving aside possible morphological and excess free volume of mixing effects, it is in part attributed to the nature of the blend itself. © 1995 John Wiley & Sons, Inc.     

Miscibility and crystallization behavior of poly(ether ether ketone ketone)/poly(ether imide) blends

The miscibility and crystallization behavior of poly(ether ether ketone ketone) (PEEKK)/poly(ether imide) (PEI) blends prepared by melt‐mixing were investigated by differential scanning calorimetry. The blends showed a single glass transition temperature, which increased with increasing PEI content, indicating that PEEKK and PEI are completely miscible in the amorphous phase over the studied composition range (weight ratio: 90/10–60/40). The cold crystallization of PEEKK blended with PEI was retarded by the presence of PEI, as is apparent from the increase of the cold crystallization temperature and decrease of the normalized crystallinity for the samples anealed at 300°C with increasing PEI content. Although the depression of the apparent melting temperature of PEEKK blended with PEI was observed, there was no evidence of depression in the equilibrium melting temperature. The analysis of the isothermal crystallization at 313–321°C from the melt of PEEKK/PEI (100/0, 90/10, and 80/20) blends suggested that the retardation of crystallization of PEEKK is caused by the increase of the crystal surface free energy in addition to the decrease of the mobility by blending PEI with a high glass transition temperature. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 769–775, 2001     

Micro‐ and ultrafiltration film membranes from poly(ether ether ketone) (PEEK)

Film membranes from the thermoplastic poly(ether ether ketone) (PEEK) have been extruded and tested for their microfiltration and ultrafiltration performance. High‐performance asymmetric membranes have been obtained by extruding polymer blends of PEEK, polysulphone, and a small molecule solvent mixture, and then by removing the polysulphone and solvent in a subsequent extraction step. The process for making ultrafiltration membranes differs from microfiltration membranes only in the relative blend components, and the temperature of the film pick‐up rolls. Processing parameters with important effects on the membrane performance have been identified. Microfiltration membranes are characterized by their pore‐size distributions and SEM, and ultrafiltration membranes by their rejection of bovine serum albumin, bubble point, and SEM. Composite membrane for nanofiltration utilizing the PEEK ultrafiltration membrane as a substrate performed similarly to a commercial membrane for the same purpose. This work details the best method for making PEEK film membranes published to date. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 1146–1155, 1999     

Microstructure and ultimate properties of injection molded amorphous engineering plastics: Poly(ether imide) and poly(2,6-dimethyl-1,4-phenylene ether)

Specimens of two engineerig plastics i.e., poly(ether imide), PEI, and poly(2,6-dimethyl- 1,4-phenylene ether), PPE, were injection molded employing a 40t Van Dorn injection molding machine and industrial practices. The mold and melt temperatures and the injection speed were varied in a limited range which furnished acceptable samples. The density, birefringence, residual stress distributions, flexure and tensile properties, and crack development of the injection molded specimens were studied. Vacuum compression molded samples were also prepared to investigate the role played by the cooling rate in shaping microstructural distributions. The results revealed significant differences in the development of microstructure of the molded specimens of the two resins, which was related to rheology and molding conditions on one hand and to development of cracks and ultimate properties on the other hand.     

Compatibility studies of sulfonated poly(ether ether ketone)–poly(ether imide)–polycarbonate ternary blends

Binary blends of the sulfonated poly(ether ether ketone) (SPEEK)–poly(ether imide) (PEI) and SPEEK–polycarbonate (PC), and ternary blends of the SPEEK–PEI–PC, were investigated by differential scanning calorimetry. SPEEK was obtained by sulfonation of poly(ether ether ketone) using 95% sulfuric acid. From the thermal analysis of the SPEEK–PEI blends, single glass transition temperature (T_g) was observed at all the blend composition. For the SPEEK–PC blends, double T_gs were observed. From the results of thermal analysis, it is suggested that the SPEEK–PEI blends are miscible and the SPEEK–PC blends are immiscible. Polymer–polymer interaction parameter (χ₁₂) of the SPEEK–PEI blends was calculated from the modified Lu and Weiss equation, and found to range from −0.011 to −0.825 with the blend composition. For the SPEEK–PC blends, the χ₁₂ values were calculated from the modified Flory–Huggins equation, and found to range from 0.191 to 0.272 with the blend composition. For the SPEEK–PEI–PC ternary blends, phase separation regions that showed two T_gs were found to be consistent with the spinodal curves calculated from the χ₁₂ values of the three binary blends. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 78: 2488–2494, 2000