Using water‐soluble nickel acetate as hole collection layer for stable polymer solar cells

We report polymer solar cells (PSCs) based on poly(3‐hexylthiophene (P3HT) and [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (PCBM) using water‐soluble nickel acetate (Ni(CH₃COO)₂, NiAc) instead of acidic poly(3,4‐ethylenedioxythiophene) : poly(styrenesulfonate) (PEDOT : PSS) as hole collection layer (HCL) between the indium tin oxide (ITO) electrode and photoactive layer. The NiAc layer can effectively decrease R_s and increase R_p and shows effective hole collection property. Under the illumination of AM1.5G, 100 mW/cm², the short‐circuit current density (J_sc) of the NiAc based device (ITO/NiAc/P3HT : PCBM/Ca/Al) reach 11.36 mA/cm², which is increased by 11% in comparison with that (10.19 mA/cm²) of PEDOT : PSS based device (ITO/PEDOT : PSS/P3HT : PCBM/Ca/Al). The power conversion efficiency of the NiAc based devices reach 3.76%, which is comparable to that (3.77%) of the device with PEDOT : PSS HCL under the same experimental conditions. Moreover, NiAc based PSCs show superior long‐term stability than PEDOT : PSS based PSCs. Our work gives a new option for HCL selection in designing more stable PSCs. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Effect of layer thickness on the electrical parameters and conduction mechanisms of conjugated polymer‐based heterojunction diode

In this study, thickness‐dependent current density–voltage (J–V) characteristics obtained for poly{(9,9‐dioctylfluorene)?2,7‐diyl‐(4,7‐bis(thien‐2‐yl) 2‐dodecyl‐benzo[1,2,3] triazole)} (PFTBT) conjugated copolymer based heterojunction diode fabricated on ITO were investigated in terms of electrical characteristics. In order to analyze J –V plots with ITO/PEDOT:PSS/PFTBT:PC₆₁BM/LiF/Al configuration, the thickness‐dependent J–V measurements were applied in the thickness range between 90 and 200 nm. The effect of PFTBT:PC₆₁BM layer thickness on the forward J –V characteristics were investigated by evaluating electrical parameters such as zero bias barrier height (Φ_Bo), ideality factor (n ), shunt resistance (R _sh), series resistance (R_s ), the interface states density (N _ss), and space‐charge limited mobility. The results show that at PFTBT:PC₆₁BM layer thickness of 90 and 200 nm, ideality factor for ITO/PEDOT:PSS/PFTBT:PC₆₁BM/LiF/Al heterojunction diodes ranged from 2.726 to 3.121 and the thermionic emission over the heterojunction diodes is crucial at low current densities and the intrinsic thermally generated charge carriers controlled the forward current this region of the heterojunction diode. At relatively higher voltage, the current mechanism of ITO/PFTBT:PC₆₁BM/PEDOT:PSS/LiF/Al heterojunction diodes were found to obey a space charge limited (SCLC) conduction mechanism. The values of N_ss and R_s in heterojunction diodes increase with increasing PFTBT:PC₆₁BM layer thickness and effect the main electrical parameters of diodes. In addition, the leakage current of heterojunction diodes are taken and interpreted via Poole‐Frenkel emission and Schottky emission. The leakage current was controlled in ITO/PEDOT:PSS/PFTBT:PC₆₁BM/LiF/Al heterojunction diodes by Poole‐Frenkel emission above 140 nm and by Schottky emission under 140 nm. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134 , 44817.     

Electroluminescence and photovoltaic properties of poly(p‐phenylene vinylene) derivatives with dendritic pendants

A copolymer of dendronized poly(p‐phenylene vinylene) (PPV), poly{2‐[3′,5′‐bis (2′‐ethylhexyloxy) bnenzyloxy]‐1,4‐phenylene vinylene}‐co‐poly[2‐methoxy‐5‐(2′‐ethylhexyloxy)‐1,4‐phenylene vinylene] (BE‐co‐MEH–PPV), was synthesized with the Gilch route to improve the electroluminescence and photovoltaic properties of the dendronized PPV homopolymer. The polymer was characterized by ultraviolet–visible absorption spectroscopy, photoluminescence spectroscopy, and electrochemical cyclic voltammetry and compared with the homopolymers poly{2‐[3′, 5′‐bis(2‐ethylhexyloxy) benzyloxy‐1,4‐phenylene vinylene} (BE–PPV) and poly[2‐methoxy‐5‐(2′‐ethylhexyloxy)‐1,4‐phenylenevinylene] (MEH–PPV). Polymer light‐emitting diodes based on the polymers with the configuration of indium tin oxide (ITO)/poly(3,4‐ethylene dioxythiophene) : poly(styrene sulfonate) (PEDOT : PSS)/polymer/Ca/Al were fabricated. The electroluminescence efficiency of BE‐co‐MEH–PPV reached 1.64 cd/A, which was much higher than that of BE–PPV (0.68 cd/A) and a little higher than that of MEH–PPV (1.59 cd/A). Photovoltaic properties of the polymer were studied with the device configuration of ITO/PEDOT : PSS/polymer : [6,6J‐phenyl‐C₆₁‐butyric acid methyl ester] (PCBM)/Mg/Al. The power conversion efficiency of the device based on the blend of BE‐co‐MEH–PPV and PCBM with a weight ratio of 1 : 3 reached 1.41% under the illumination of air mass 1.5 (AM1.5) (80 mW/cm²), and this was an improvement in comparison with 0.24% for BE–PPV and 1.32% for MEH–PPV under the same experimental conditions. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Dioctylfluorene‐thiophene based conjugated copolymers for bulk heterojunction solar cells and enhanced power conversion efficiency via methanol treatment

Sensible design and synthesis of conjugating polymers is important to the development of polymer solar cells (PSCs). In this work, we synthesized and characterized two dioctylfluorene‐thiophene based conjugated copolymers, PFTDPP and PFTpBT, having different acceptor groups on the backbone. The photovoltaic properties of the copolymers blended with 6,6‐phenyl‐C₆₁‐butyric acid methyl ester (PC₆₁BM) as an electron acceptor were obtained. The PSC based on a conventional device configuration ITO/PEDOT:PSS/ Polymer:PC₆₁BM/LiF/Al showed power conversion efficiencies (PCEs) of 2.42% and 3.02% for PFTDPP and PFTpBT, respectively. Methanol treatment was introduced to further optimize device performance, and the solvent treatment gave a dramatic increase in PCE. The best PCEs could reach 4.25% and 4.20% after methanol treatment under AM 1.5G illumination with an intensity of 100 mW cm^?2 from a solar simulator. © 2015 Society of Chemical Industry     

Towards optimization of functionalized single-walled carbon nanotubes adhering with poly(3-hexylthiophene) for highly efficient polymer solar cells

In this paper, we present the optimization of single-walled carbon nanotubes (SWCNTs) by acid-treatment, solution ultrasonication time and dispersion in photoactive layer for efficient organic solar cells. After non-covalently adhering with poly(3-hexylthiophene) (P3HT), pre-functionalized SWCNTs were blended into the composites of P3HT and [6,6]-phenyl-C₆₁-butyric acid methyl ester (PCBM) as photoactive layer, and a maximum power conversion efficiency (PCE) of 3.02% with a short-circuit current density of 11.46 mA/cm² was obtained from photovoltaic cell indium-tin oxide (ITO)/poly(ethylene-dioxythiophene):poly(4-styrenesulfonate) (PEDOT:PSS)/P3HT:PCBM:SWCNTs/Al with an optimum 0.3 wt% SWCNTs in P3HT:PCBM:SWCNTs nanocomposite, the PCE can be enhanced by more than 10% as compared to the control device ITO/PEDOT:PSS/P3HT:PCBM/Al. The performance improvement by incorporating with functionalized SWCNTs is mainly attributed to the extension of excitons dissociation area and fastening charge carriers transfer across the active layer.     

Polylactide‐perylene derivative for blue biodegradable organic light‐emitting diodes

In this work we demonstrate, for the first time, the use of polylactic acid (PLA) as a biodegradable host matrix for the construction of the active emissive layer of organic light‐emitting diode (OLED) devices for potential use in bioelectronics. In this preliminary study, we report a robust synthesis of two fluorescent PLA derivatives, pyrene‐PLA ( AH10 ) and perylene‐PLA ( AH11 ). These materials were prepared by the ring opening polymerisation of l ‐lactide with hydroxyalkyl‐pyrene and hydroxyalkyl‐perylene derivatives using 1,8‐diazabicyclo[5.4.0]undec‐7‐ene as catalyst. OLEDs were fabricated from these materials using a simple device architecture involving a solution‐processed single‐emitting layer in the configuration ITO/PEDOT:PSS/PVK:OXD‐7 (35%): AH10 or AH11 (20%)/TPBi/LiF/Al (ITO, indium tin oxide; PEDOT:PSS, poly(3,4‐ethylenedioxythiophene) doped with poly(styrenesulfonic acid); PVK, poly(vinylcarbazole); OXD‐7, (1,3‐phenylene)‐bis‐[5‐(4‐tert‐butylphenyl)‐1,3,4‐oxadiazole]; TPBi, 2,2′,2″‐(1,3,5‐benzenetriyl)tris(1‐phenyl‐1H‐benzimidazole)). The turn‐on voltage for the perylene OLED at 10 cd m^–2 was around 6 V with a maximum brightness of 1200 cd m^–2 at 13 V. The corresponding external quantum efficiency and device current efficiency were 1.5% and 2.8 cd A^–1 respectively. In summary, this study provides proof of principle that OLEDs can be constructed from PLA, a readily available and renewable bio‐source. © 2020 The Authors. Polymer International published by John Wiley & Sons Ltd on behalf of Society of Industrial Chemistry.     

Synthesis of oxadiazole‐based polymers containing a carbazole–vinylene or fluorene–vinylene group and their hole‐injection/transport behavior in light‐emitting diodes

A series of conjugated (poly{N‐(2‐ethylhexyl)‐3,6‐carbazole–vinylene‐alt‐[(2,5‐bisphenyl)‐1,3,4‐oxadiazole]}) and nonconjugated (poly{N‐(2‐ethylhexyl)‐3,6‐carbazole–vinylene‐alt‐[(2,5‐bisphenol)‐1,3,4‐oxadiazole]}) and poly{9,9‐dihexyl‐2,7‐fluorene–vinylene‐alt‐[(2,5‐bisphenol)‐1,3,4‐oxadiazole]}) polymers containing oxadiazole and carbazole or fluorene moieties in the polymer backbone were synthesized with a multiple‐step procedure. The properties of the polymers, including the photophysical and electrochemical characteristics, could be fine‐tuned by adjustment of the components or structures in the polymer chains. The polymers were used to examine the hole‐injection/transport behavior as hole‐injection/hole‐transport layers in double‐layer indium tin oxide (ITO)/polymer/aluminum tris(8‐hydroxyquinoline)/LiF/Al devices by the determination of their energy levels. The effects of the polymers in these devices on the charge‐transport behavior were compared with a control device fabricated with poly(ethylenedioxythiophene) (PEDOT)–poly(styrene sulfonate) (PSS). Devices containing the synthesized polymers showed comparable adhesion to the ITO anode and good hole‐injection/transport performance. In addition, they exhibited higher electroluminescence over an identical range of current densities than the control device. This was attributed to the prevention of radiative exciton quenching caused by the PEDOT–PSS interfaces and the improvement of electron/exciton blocking due to the higher electron affinity of the synthesized polymers. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Synthesis,electroluminescence, and photovoltaic cells of new vinylene‐copolymers with 4‐(anthracene‐10‐yl)‐2,6‐diphenylpyridine segments

Three new soluble vinylene‐copolymers F , C, and P that contain 4‐(anthracene‐10‐yl)‐2,6‐diphenylpyridine as common segment and fluorene, carbazole, or phenylene, respectively, as alternating segment were prepared by Heck coupling. The glass transition temperature was high for F and C (110 and 117°C), whereas was lower than 25°C for P . The polymers were stable up to ～ 300°C. They emitted blue–green light with maximum located at wavelength of 456–550 nm, which was of the order F < C < P . The photoluminescence quantum efficiency in THF solution was ～ 30% for F and P and only 5% for C . All three copolymers were used as active layers for polymer light emitting diodes (PLEDs) and organic photovoltaic cells. The double PLEDs with configuration of indium‐tin oxide (ITO)/poly(ethylenedioxythiophene (PEDOT) : poly(styrenesulfonate)(PSS)/Copolymer F , C , or P /TPBI(1,3,5‐tris(2‐N‐phenylbenzimidazolyl)benzene)/Ca/Al were fabricated. Copolymer P emitted green light with maximum brightness of 28 cd/m² and a current yield of 0.85 cd/A. Organic photovoltaics with the configuration of ITO/PEDOT : PSS/Copolymer and [6,6]‐phenyl‐C61‐butyric acid methyl ester blend (1 : 1) /Ca/Al were also fabricated. Copolymer P showed the highest power conversion efficiency of 0.034%. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

High-performance poly(2,3-diphenyl-1,4-phenylene vinylene)-based polymer light-emitting diodes by blade coating method

A new series of super high brightness and luminance efficient poly(2,3-diphenyl-1,4-phenylene vinylene) (DP-PPV)-based electroluminescent (EL) polymers containing methoxy or long branched alkoxy chains were synthesized via Gilch polymerization. The branched alkoxy groups were introduced to enhance solubility for blade and spin-coating processes. Monomers of DMeO-PPV and m-Ph-PPV were used to increase steric hindrance and prevent close packing of the main chain. By controlling the feeding ratio of different monomers during polymerization, DP-PPV derivatives with high molecular weight were obtained. All synthesized polymers possess high glass transition temperatures and thermal stabilities. The maximum photoluminescent emissions of the thin films are located between 544 and 547 nm. Cyclic voltammetry analysis reveals that the band gaps of these light-emitting materials are in the range of 2.75-2.84 eV. Blade coating was used to fabricate multilayer polymer light-emitting diodes. A multilayer electroluminescent device with the configuration of ITO/PEDOT:PSS/TFB/P1/TPBi/LiF/Al exhibited a very high luminescence efficiency (10.96 cd A⁻¹). The maximum brightness of the multilayer EL device ITO/PEDOT:PSS/TFB/P3/CsF/Al reached up to 78,050 cd m⁻² with a low turn-on voltage (4.0 V). For further investigation, polymer P3 was blended with DPPFBNA to achieve white light-emitting device; the multilayer devices generated a maximum brightness of 1085 cd m⁻² and a luminance efficiency of 0.75 cd A⁻¹, with CIE coordinates (0.28, 0.33) at 11 V.     

Effects of solution processing on the photovoltaic response of poly(n‐vinyl carbazole) films

The effects of solution processing on the photovoltaic response of poly(n‐vinyl carbazole) (PVK) films were investigated. PVK films were formed by spincasting onto glass coated with indium tin oxide (ITO) and poly(3,4‐ethylenedioxythiophene) (PEDOT)–polystyrenesulfonate (PSS). Some of the PVK films were redissolved in chlorobenzene and redried in the absence or presence of an electric field. Illuminated current–voltage characteristics were measured for an ITO/PEDOT:PSS/PVK/Ca:Al device. Films spincast from a 50 mg/mL solution, redissolved, and dried in the absence of the electric field exhibited a 26% higher charge collection efficiency than films dried in the presence of the electric field. The increased charge collection efficiency was attributed to changes in the molecular configuration of the PVK films. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

In situ-prepared composite materials of PEDOT: PSS buffer layer-metal nanoparticles and their application to organic solar cells

We report an enhancement in the efficiency of organic solar cells via the incorporation of gold (Au) or silver (Ag) nanoparticles (NPs) in the hole-transporting buffer layer of poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS), which was formed on an indium tin oxide (ITO) surface by the spin-coating of PEDOT:PSS-Au or Ag NPs composite solution. The composite solution was synthesized by a simple in situ preparation method which involved the reduction of chloroauric acid (HAuCl₄) or silver nitrate (AgNO₃) with sodium borohydride (NaBH₄) solution in the presence of aqueous PEDOT:PSS media. The NPs were well dispersed in the PEDOT:PSS media and showed a characteristic absorption peak due to the surface plasmon resonance effect. Organic solar cells with the structure of ITO/PEDOT:PSS-Au, Ag NPs/poly(3-hexylthiophene):[6,6]-phenyl-C61-butyric acid methyl ester (P3HT:PCBM)/LiF/Al exhibited an 8% improvement in their power conversion efficiency mainly due to the enlarged surface roughness of the PEDOT:PSS, which lead to an improvement in the charge collection and ultimately improvements in the short-circuit current density and fill factor.     

Synthesis and optoelectronic properties of thermally cross-linkable fluorene derivative containing hole-transporting triphenylamine terminals

This paper describes the synthesis of a solution-processable and thermally cross-linkable 2,7-bis-[4-bis(4-vinylphenyl)aminophenyl]-9,9-dihexylfluorene (VTF) and its application as hole-transporting layer in multilayer polymer light-emitting diodes (PLEDs). The thermal, photophysical, and electrochemical properties of VTF were investigated by differential scanning calorimetry, thermogravimetric analysis, optical spectroscopy, and cyclic voltammetry. The VTF is readily cross-linked via vinyl groups by heating at 180 °C for 30 min to obtain homogeneous film with excellent solvent resistance. Multilayer PLEDs (ITO/PEDOT:PSS/cured-VTF/MEH-PPV/Ca/Al) were readily fabricated by spin-coating process using cross-linked VTF as hole-transporting layer (HTL). The maximum brightness (13,640 cd/m²) and current efficiency (0.69 cd/A) were superior to those without HTL (ITO/PEDOT:PSS/MEH-PPV/Ca/Al: 7810 cd/m², 0.28 cd/A). In addition, the cured-VTF could replace conventional hole-injection layer (PEDOT:PSS) to reveal comparable performance (8240 cd/m², 0.44 cd/A). Current results indicate that the VTF with four thermally cross-linkable terminal vinyl groups is a promising optoelectronic material, which is readily processed by wet processes.     

Effect of solvent on electrical conductivity and gas sensitivity of PEDOT: PSS polymer composite films

Poly(3,4‐ethylenedioxythiophene)/poly(styrene sulfonate) (PEDOT:PSS) was blended with polyethylene oxide (PEO) and polyvinyl alcohol (PVA) and composite film was cast. Additional solvents of dimethyl sulfoxide (DMSO) and ethylene glycol (EG) were mixed and their effects on electrical conductivity and structural changes were investigated. The electrical conductivity increased in response to the additional solvent, leading to an increase in the PEDOT ratio relative to the control. PEDOT:PSS/PEO composite film had a much higher electrical conductivity than PEDOT:PSS/PVA. When blended with PEO, the quinoid structure revealed by Raman spectroscopy increased relative to the PVA‐blended case, indicating higher electrical conductivity. The current–voltage response and gas sensitivity showed much better performance in PEDOT:PSS/PEO/DMSO composite film. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42628.     

Optimization of organic bi-layer solar cell through systematic study of anode treatment and material thickness

The performance of bi-layer organic solar cells with the structure ITO/PEDOT:PSS/CuPc/C₆₀/BCP/Al was optimized. Prior to cell deposition, an optimal indium tin oxide (ITO) surface treatment technique was determined, with N₂ plasma treatment providing the highest solar cell efficiency. Parametric studies were performed to identify optimal fabrication conditions and deposition thicknesses for each layer by using solar cell efficiency as the primary performance measure.     

Synthesis of a soluble polythiophene copolymer with thiophene–vinylene conjugated side chain and its applications in photovoltaic devices

A new soluble polythiophene copolymer with thiophene‐vinylene conjugated side chain poly[3‐(5′‐octylthienylenevinyl) thiophene]‐thiophene (POTVTh‐Th) was successfully synthesized and characterized using NMR, UV‐visible spectroscopy, etc. To study the photovoltaic property of the copolymer, photovoltaic device of ITO/PEDOT:PSS/POTVTh‐Th:[6,6]‐phenyl C₆₁‐butyric acid methyl ester (PC₆₁BM) (weight ratio being 1 : 1)/LiF/Al was fabricated, in which POTVTh‐Th acted as the electron donor in the active layer. Under 100 mW/cm² AM 1.5G simulated solar emission, the open‐circuit voltage and the short‐circuit current density of the device were 0.58 V and 2.50 mA/cm², respectively. The power conversion efficiency and the fill factor of the photovoltaic device were evaluated to be 0.42% and 0.30. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Hole-limiting conductive vinyl copolymers for AlQ3-based OLED applications

A series of soluble conductive vinyl copolymers containing a hole-transporting N-(4-methoxyphenyl)-N-phenylnaphthalen-1-amine (MeONPA) moiety and an electron-transporting/hole-blocking 2,5-diphenyl-1,3,4-oxadiazole (OXA) moiety at different composition ratios were synthesized and characterized. The copolymers were applied as the hole-transporting layer (HTL) for a series of heterojunction Organic Light-emitting Diodes (OLEDs) employing the commonly used green emitter tris(8-hydroxyquinolinato)aluminum (AlQ₃) as the electron-transporting layer. AlQ₃ is known to have inferior electron mobility compared to most typical hole-transporting materials. As a result, oxidative degradation of the AlQ₃ emitters caused by the excessive holes accumulated at the interface led to deterioration of the device over time. From the measurement of hole current only devices using electron blocking gold as cathode (ITO/PEDOT:PSS/copolymer/Au), it was found that the hole current for the copolymers reduced as the OXA composition increased. Optimum performance for the AlQ₃-based OLED (ITO/PEDOT:PSS/copolymer/AlQ₃/Ca/Al) was achieved for a 82/18 (molar ratio) (MeONPA/OXA) copolymer. The maximum current efficiency and luminance were 4.2 cd/A and ca 24,000 cd/m² respectively for the charge-balanced copolymer compared to 3.5 cd/A and 6600 cd/m² for similar device employing a homopolymer P(MeONPA) as the HTL.     

Improving the efficiency of ITO/nc-TiO2/CdS/P3HT:PCBM/PEDOT:PSS/Ag inverted solar cells by sensitizing TiO2 nanocrystalline film with chemical bath-deposited CdS quantum dots

An improvement in the power conversion efficiency (PCE) of the inverted organic solar cell (ITO/nc-TiO₂/P3HT:PCBM/PEDOT:PSS/Ag) is realized by depositing CdS quantum dots (QDs) on a nanocrystalline TiO₂ (nc-TiO₂) film as a light absorption material and an electron-selective material. The CdS QDs were deposited via a chemical bath deposition (CBD) method. Our results show that the best PCE of 3.37% for the ITO/nc-TiO₂/CdS/P3HT:PCBM/PEDOT:PSS/Ag cell is about 1.13 times that (2.98%) of the cell without CdS QDs (i.e., ITO/nc-TiO₂/P3HT:PCBM/PEDOT:PSS/Ag). The improved PCE can be mainly attributed to the increased light absorption and the reduced recombination of charge carriers from the TiO₂ to the P3HT:PCBM film due to the introduced CdS QDs.     

Effect of microstructure on the dielectric properties of poly(vinyl alcohol)–poly(3,4‐ethylenedioxythiophene) doped with poly(styrenesulfonate) composite films

Poly(3,4‐ethylenedioxythiophene) doped with poly(styrenesulfonate) (PEDOT–PSS) was blended with poly(vinyl alcohol) (PVA) to form 0, 10, 20, 30, 40, and 50 vol % PEDOT–PSS/PVA solutions, and their freestanding films were prepared with a simple and cost‐effective solution casting technique at 27 °C in the absence of additives. Field emission scanning electron microscopy images revealed changes in the cocontinuous network to a rodlike morphology in the composite films from 10 to 50 vol % PEDOT–PSS/PVA. The alternating‐current conductivity was found to obey Jonscher's power law. The obtained values of the dielectric constant at 27 °C were relatively high, and a maximum value of 6.7 × 10⁴ at 100 Hz for 40 vol % PEDOT–PSS'/PVA was observed. The dielectric loss attained a maximum value of about 10⁶ at 100 Hz for 40 vol % PEDOT–PSS/PVA. However, a decrease in the dielectric parameters was observed at 50 vol % PEDOT–PSS/PVA because of locally induced strain in the microstructure. The variations in polarization with respect to the applied electric field (P–E) were determined for 50, 100, and 500 Hz at 500 V for the freestanding composite films of lower concentrations up to 20 vol % PEDOT–PSS/PVA. In summary, the dielectric and P–E measurements confirmed that the electrical characteristics changed in accordance to the contribution from both resistive and capacitive sites in the PEDOT–PSS/PVA composites. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45079.     

Quinolinyl‐moiety‐containing 3‐ester‐substituted polythiophenes showing fluorescence efficiency

Polythiophenes with ester substituents at the 3‐position of the thiophene ring were synthesized by ferric chloride oxidative polymerization. The polythiophenes are partially soluble in tetrahydrofuran, and these solutions were used to characterize the polythiophenes using Fourier transform infrared, ¹H NMR, UV‐visible and fluorescence spectroscopy, gel permeation chromatography, thermogravimetric analysis, differential scanning calorimetry and cyclic voltammetry. The electrochemical band gap of the polymers is in the range 1.6–2.3 eV. The effect of the various substituents on the fluorescence behaviour was studied in detail. The quinolinyl‐moiety‐containing polythiophene ester has the highest fluorescence quantum yield. The incorporation of Al³⁺ and Zn²⁺ ions increases greatly the fluorescence intensity. The electroluminescence properties of the polymers were evaluated with a device configuration of ITO/PEDOT:PSS/polymer/LiF/Al. The polymers show a yellow emission in electroluminescence spectra. The results suggest that the quinoline‐containing ester‐substituted polythiophene is a promising electronic and optoelectronic material. Copyright © 2011 Society of Chemical Industry     

Synthesis and light‐emitting properties of new poly(p‐phenylenevinylene) derivatives containing oxadiazole moiety

Two new poly(p‐phenylenevinylene) (PPV) derivatives containing the oxadiazole moiety (OXA–PPV1 and OXA–PPV2) were synthesized by the Wittig condensation polymerization reaction and their thermal and light‐emitting properties were investigated. The single‐layer and triple‐layer electroluminescent (EL) devices with configurations of ITO/OXA–PPV1/Al and ITO/OXA–PPV1/OXD/Alq₃/Al were fabricated. They both exhibited blue emission at 460 nm. For comparison, the PPV derivative containing the oxadiazole moiety only in the side chains (OXA–PPV2) was also synthesized. Both single‐layer and triple‐layer EL devices with OXA–PPV2 as the emissive layer emitted green‐light at 560 nm. The turn‐on voltages of the triple‐layer device was 11 V for OXA–PPV1 and 8 V for OXA–PPV2. The triple‐layer EL devices showed much better performance than that of the single‐layer devices. The spectra indicated that energy or electron transfer occurred from the side‐chain oxadiazole to the main‐chain styrene unit. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 2424–2428, 2002