Remarkable improvement of thermal stability of main‐chain benzoxazine oligomer by incorporating o‐norbornene as terminal functionality

A new main‐chain benzoxazine oligomer with o‐norbornene functionality as end groups has been designed and synthesized. As compared to traditional main‐chain type benzoxazine polymers, this benzoxazine oligomer with o‐norbornene terminal functionality can undergo further crosslinking polymerization after general ring‐opening polymerization of oxazine rings. Another main‐chain benzoxazine oligomer has also been designed based on the reaction of bisphenol‐A, 4,4′‐diaminodiphenylmethane, paraformaldehyde, and phenol for comparison. The structure of the synthesized oligomers is confirmed by ¹H nuclear magnetic resonance spectroscopy and Fourier transform infrared spectroscopy (FTIR). The molecular weight has been determined by using gel permeation chromatography (GPC). The benzoxazine oligomer containing o‐norbornene functionality can polymerize with multiple polymerization mechanisms rather than the single mechanism common to traditional 1,3‐benzoxazine resins. The polymerization mechanisms are monitored by in situ FTIR and differential scanning calorimetry (DSC). Moreover, the thermoset derived from the benzoxazine oligomer containing o‐norbornene functionality exhibits high thermal stability with the transition temperature of 360 °C and a high T_d5 of 404 °C. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45408.     

Curing kinetics,thermal, and adhesive properties of acetylene‐terminated benzoxazine

The acetylene‐terminated benzoxazine monomer (BB‐apa) has been synthesized using 2,2‐bis(4‐hydroxyphenyl)butane, 3‐aminophenylacetylene, and paraformaldehyde. The structure of the monomer was characterized by FTIR spectroscopy and ¹H NMR spectra, which indicated that the reactive oxazine ring and acetenyl groups existed in molecular structure of BB‐apa. The polymerization behavior was monitored by FTIR and non‐isothermal differential scanning calorimetry (DSC), which showed that the BB‐apa had completely cured with multiple polymerization mechanisms according to oxazine ring‐opening and ethynyl addition polymerization. The curing kinetics results revealed that the introduction of ethynyl groups can accelerate the ring‐opening polymerization of benzoxazine, leading to a lower curing temperature and apparent activation energy. Moreover, the thermoset derived from the BB‐apa exhibits higher thermal stability and lap shear strength (at 350 °C) with the glass transition temperature of 353 °C compared with the traditional benzoxazine polymer without ethynyl groups (BB‐a). © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44547.     

An m‐phenylenediamine‐based benzoxazine with favorable processability and its high‐performance thermoset

A novel aromatic diamine‐based benzoxazine (P‐mPDA) is successfully synthesized from m‐phenylenediamine (m‐PDA), 2‐hydroxybenzaldehyde, and formaldehyde. The polymerization behavior of P‐mPDA and the properties of its thermoset are studied. The results indicate that P‐mPDA owns favorable processability including low polymerization temperature, low liquefying temperature, and wide processing window. Even lower polymerization temperature (polymerization onset temperature as low as 80 °C) can be achieved by the promotion of catalysts. The ring‐opening polymerization of P‐mPDA first generates polybenzoxazine with N, O‐acetal‐type structure and arylamine Mannich‐type structure, following which rearrangement from N, O‐acetal‐type structure to phenolic Mannich‐type structure proceeds at elevated temperature. Furthermore, the polymerized P‐mPDA shows outstanding performance such as extremely high glass transition temperature (T_g) of 280 °C, high char yield above 53% at 800 °C under nitrogen and excellent mechanical property. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43368.     

Synthesis of a novel benzoxazine precursor containing phenol hydroxyl groups and its polymer

A novel benzoxazine precursor containing phenol hydroxyl groups was synthesized from bisphenol A, 4,4′‐diaminodiphenyl methane, and formaldehyde with a molar ratio of 2:1:4. The benzoxazine precursor was characterized with Fourier transform infrared, proton nuclear magnetic resonance, and size exclusion chromatography. The curing reaction was monitored by the gel time, differential scanning calorimetry, and Fourier transform infrared. The obtained polybenzoxazine showed high thermal stability and a high glass‐transition temperature. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Curing behaviors and thermal properties of benzoxazine and N,N′‐(2, 2, 4‐trimethylhexane‐1, 6‐diyl) dimaleimide blend

A blend of bisphenol‐A based benzoxazine (BA‐a)/N, N′‐(2, 2, 4‐Trimethylhexane‐1, 6‐diyl) dimaleimide (TBMI) with the ratio of 1:1 was prepared and its curing behaviors were studied by differential scanning calorimetry (DSC), Fourier Transform Infrared (FTIR). The curing mechanism was proposed based on the semiquantitative analysis from FTIR spectra. The model compound was used to study the catalysis effect of BA‐a on the curing reaction of TBMI. It was found the curing reactions of BA‐a and TBMI not only proceeded simultaneously, but their coreactions also occurred. The research further indicated that negative oxygen ions from ring opening of benzoxazine mainly promoted the polymerization of maleimide groups, even though the amine group of benzoxazine had a positive effect on the reaction of maleimide groups. Besides, BA‐a and TBMI blends showed improved thermal properties based on the results from DMA and TGA. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Dynamic mechanical and shape memory properties of polybenzoxazines based on aminopropyl‐terminated siloxanes

Four siloxane‐containing benzoxazine monomers and telechelic benzoxazine oligomers were synthesized from 1,3‐bis(3‐aminopropyl)‐1,1,3,3‐tetramethyldisiloxane, α,ω‐bis(3‐aminopropyl)polydimethylsiloxane, phenol, o‐allylphenol, and formaldehyde. The length of the siloxane segment affects the polymerization reaction of the benzoxazine monomers and telechelic benzoxazine oligomers. The dynamic mechanical properties of the corresponding polybenzoxazines depend primarily on the structure of phenol and the length of the siloxane segment. The polybenzoxazines exhibit one‐way dual‐shape memory behavior in response to changes in temperature. The thermally induced shape memory effects of the polybenzoxazines were characterized by bending and tensile stress–strain tests with a temperature program based on their glass transition temperatures. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 44121.     

Curing reaction mechanism and heat resistance properties of hexa‐(4‐carboxyl‐phenoxy)‐cyclotriphosphazene/bisphenol A aniline benzoxazine blends

A blend system of hexa‐(4‐carboxyl‐phenoxy)‐cyclotriphosphazene (HCPCP) and bisphenol A aniline benzoxazine (BA‐a) was prepared, and its curing reaction mechanism and heat resistance properties were studied. The curing reaction mechanism of the blend was explored by differential scanning calorimetry, Fourier transform infrared spectroscopy, and modeling software using model compounds Ar‐COOH and hexachlorocyclotriphosphazene (HCCP). The heat resistance properties of the cured blends were studied by thermogravimetric analysis and dynamic mechanical analysis. The polymerization of benzoxazine was catalyzed by HCPCP through phosphazene ring and acid groups, and phosphazene played a predominant role. Compared with the materials with a single functional group (Ar‐COOH and HCCP), HCPCP containing two functional groups (phosphazene ring and acid) exhibited weaker catalytic effects, mainly due to the high molecular weight of HCPCP obstructing movement and causing steric hindrance. In addition, HCPCP had a positive effect on the thermal stability of polybenzoxazine from 250 to 400 °C. When the HCPCP content reached 3%, the cured blend had the highest glass‐transition temperature (222.2 °C), which is higher by 20 °C than that of cured benzoxazine. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46389.     

Improved synthesis and properties of hydroxyl‐terminated liquid fluorosilicone

The synthesis of hydroxyl‐terminated poly(trifluoropropylmethyl)siloxane (PTFPMS‐OH) by anionic ring‐opening polymerization of 1,3,5‐tris(trifluoropropylmethyl)cyclotrisiloxane (D₃F) was studied in bulk using potassium hydroxide as an initiator in the presence of several reaction stabilizers. The promoting effect of the reaction stabilizers for the polymerization of D₃F was investigated by GPC and NMR analyses. Results showed that the selected reaction stabilizers exhibited a significant promoting effect. This new process of polymerization produced well‐defined α,ω‐dihydroxylated polysiloxane in very high yields. The addition of reaction stabilizers could almost completely suppress back‐biting reactions during the polymerization. It was found that there lies an exponential decay relationship between the molecular weight of PTFPMS‐OH and amount of end‐capping agent. Thus, by adjusting the reaction conditions strictly, the molecular weight of the fluorosilicone could be controlled accurately, and meanwhile a broad “terminate window” could be implemented. Thermogravimetic (TG) analysis indicated that PTFPMS‐OH could be used in a wide range of operational temperatures. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43220.     

Synthesis of branched benzoxazine monomers with high molecular mass,wide processing window,and properties of corresponding polybenzoxazines

Four cyclotriphosphazene‐based benzoxazine monomers (I, II, III, and IV) with relatively high molecular weight were synthesized by a nucleophilic substitution reaction, and their chemical structures were confirmed by ¹H‐NMR and ³¹P‐NMR. A new term, oxazine value (OV, similar to epoxy value), was first proposed to explain the structure–property relationship of the cured polymers. The polymerization behaviors of the four monomers were studied by differential scanning calorimetry and Fourier transform infrared spectroscopy. The maximum exothermic peaks of the four monomers are in the range 244–248 °C. All monomers possess a wide processing window despite their high molecular weight. The thermal stability, glass‐transition temperature (T_g), and mechanical properties of each cured polymer were studied by thermogravimetric analysis and dynamic mechanical thermal analysis. The char yield at 850 °C, T_g, and storage moduli of PIV (polybenzoxazine obtained from monomer IV) are 60.0%, 218 °C, and 9.0 GPa, respectively. The surface property and humidity absorption character of the cured polybenzoxazines were also studied. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44453.     

In Vitro evaluation and dissipative particle dynamics simulation of PLGA‐PEG‐PLGA

Thermosensitive PLGA‐PEG‐PLGA triblock copolymers have great potential to be utilized in intravitreal injection. It is important to understand the mechanisms of selfassembled behaviors of triblock copolymers. In this study, dissipative particle dynamics simulation is used to explore the phase behaviors and morphologies of the copolymers. Phase transition, complex viscosities, swelling characteristics, and degradation behavior were investigated. The results suggested that the structures of copolymers were greatly affected by polymer concentration. Phase behavior of copolymers can be modified by alternating polymer size distribution. It exhibited that particle diameter was temperature dependence and polymer concentration can increase micelles numbers in solutions. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41280.     

Cure characterization of the ring‐opening metathesis polymerization of linseed oil‐based thermosetting resins

BACKGROUND: Bio‐based polymers from vegetable oils are excellent alternatives to petroleum‐based resins for both environmental and economic reasons. A detailed understanding of the cure behavior of bio‐based polymers is essential to optimize cure schedules and the final properties of the polymers. In this work, the cure of newly developed linseed oil‐based thermosetting resins, synthesized using Grubbs' first‐generation catalyst and a bis‐norbornadiene cross‐linking agent by ring‐opening metathesis polymerization, is characterized using differential scanning calorimetry (DSC) and parallel plate oscillatory rheometry. RESULTS: Experimental results reveal that the rate of cure increases and the gel time decreases with increasing cross‐linker loading; however, the activation energy of the cure does not vary systematically with cross‐linker loading. Phenomenological reaction models are used to describe the dynamic DSC measurements and to determine the kinetic parameters which facilitate cure predictions under isothermal conditions. CONCLUSION: This work demonstrates that the cure kinetics of a linseed oil‐based thermosetting resin can be controlled by varying the cross‐linker loading. Furthermore, the kinetic parameters and cure rates at any cross‐linker loading for this system can be described by a simple autocatalytic reaction model which facilitates development of cure schedules. Copyright © 2009 Society of Chemical Industry     

Effect of novel benzoxazine reactive diluent on processability and thermomechanical characteristics of bi‐functional polybenzoxazine

Effects of a monofunctional benzoxazine diluent (Ph‐a) on properties of a bifunctional benzoxazine resin (BA‐a) have been investigated. The BA‐a/Ph‐a mixtures are miscible in nature rendering the properties highly dependent on their compositions. The viscosity of the BA‐a resin can be reduced to one third using only about 10% by weight the Ph‐a diluent. The addition of the Ph‐a resin into the BA‐a resin can also lower the liquefying temperature of the resin mixtures whereas the gel point is marginally decreased. The gel point, which depends on the BA‐a/Ph‐a mixtures and the cure temperature, was determined by the frequency independence of loss tangent in the vicinity of the sol‐gel transition. The relaxation exponent values of the copolymer were found to be 0.24–0.55, which is dependent on the cure temperature. Gel time of the BA‐a/Ph‐a systems decreases with increasing temperature according to an Arrhenius relation with activation energy of 60.6 ± 1.5 kJ/mol. Flexural moduli of the BA‐a/Ph‐a polymers also increase with the Ph‐a mass fraction, however, with the sacrifice of their flexural strength and glass‐transition temperature. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Synthesis and characterization of 4,4′‐diaminodiphenyl methane‐based benzoxazines and their polymers

A series of diamine‐based benzoxazine precursors have been prepared using 4,4′‐diaminodiphenyl methane, formaldehyde, and different phenol derivatives including phenol, p‐cresol, and 2‐naphthol. Their chemical structures were identified by FTIR, ¹H NMR, and elemental analysis. The curing reactions of those precursors were monitored by FTIR and DSC. The obtained materials exhibited higher glass transition temperature and char yields than the corresponding bisphenol‐A based polybenzoxazines. The polybenzoxazine prepared from phenol showed the highest char yields of 65% and thermal stability with 5 and 10% weight‐loss temperatures at 346 and 432°C, respectively. The polybenzoxazine prepared from 2‐naphthol exhibited the highest glass transition temperature at 244°C. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Preparation and properties of polyamide‐6‐based thermoplastic laminate composites by a novel in‐mold polymerization technique

In this work, a method for preparation of polyamide‐6 (PA6) based laminates reinforced by glass fiber‐ (GFL) or polyamide‐66 (PA66) textile structures (PL) via reactive injection molding is disclosed. It is based on in‐mold anionic polymerization of ε‐caprolactam carried out at 165°C in the presence of the respective reinforcements performed in newly developed prototype equipment whose design concept and operation are described. Both composite types were produced for reaction times of 20 min, with conversion degrees of 97–99%. Initial mechanical tests in tension of GFL samples displayed almost twofold increase of the Young's modulus and stress at break values when compared with the neat anionic PA6. The improvement was proportional to the volume fraction V_f of glass fiber fabric that was varied in the 0.16–0.25 range. A 300% growth of the impact strength was registered in PL composites with V_f of PA66 textile of 0.1. Removing the surface finish of the latter was found to be a factor for improving the adhesion at the matrix–fiber interface. The mechanical behavior of GFL and PL composites was discussed in conjunction with the morphology of the samples studied by optical and electron microscopy and the matrix crystalline structure as revealed by synchrotron X‐ray diffraction. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40083.     

Novel benzoxazine resins as photoinitiator comprising benzophenone and coinitiator amine for photopolymerization

A novel kind of benzoxazine precursors made of 4‐dihydroxybenzophenone (DHBP), formaldehyde and N, N′‐diethylethylenediamine was developed. The striking feature of this class of precursors is that it can be acted as an effective photo initiator for polymerization of acrylate monomers. In addition, this kind of precursors could be directly dispersed in water and its aqueous solution exhibited very sharp response to temperature, with a well‐defined cloud point. The structure of this precursor has been confirmed by Proton Nuclear Magnetic Resonance Spectroscopy (¹H‐NMR) and Fourier Transform Infrared spectroscopy (FTIR) and its curing behaviors are investigated by Differential Scanning Calorimetry (DSC). The photopolymerization of acylate monomers, initiated by this precursor, was studied through photo‐DSC. The results show that this precursor is dramatically more efficient than benzophenone (BP), in which the polymerization rate is almost four times as high as that of the BP system. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Synthesis and study of the oligo(ether–ester)s based on butylene oxide

Unsaturated oligo(ether–ester) was prepared by ring‐opening polymerization of butylene oxide (BO) with glycidyl methacrylate (GMA) in the presence of cationic catalyst BF₃^?O(C₂H₅)₂. The effects of mol ratio of the initial components, amount of catalyst, temperature, and reaction times on the copolymerization reaction were examined. Oligo(ether–ester) were achieved in highest yield of 82% after reaction times of 4 h at 0°C. Synthesized copolymer was characterized using spectroscopic (¹H NMR and IR) and chemical analysis methods. The thermal degradation and softing points of oligo(ether–ester)‐styrene composites were studied. It is shown that crosslinking of the unsaturated oligo(ether–ester) with styrene takes place through the use of thermostable materials. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008.     

Thermally activated polymerization behavior of bisphenol‐S/methylamine‐based benzoxazine

A bifunctional benzoxazine monomer, 6,6′‐bis(3‐methyl‐3,4‐dihydro‐2H‐benzo[e] [1,3]oxazinyl) sulfone (BS‐m), was synthesized from bisphenol‐S, methylamine, and formaldehyde via a solution method. The chemical structure of BS‐m was characterized with ¹H and ¹³C‐nuclear magnetic resonance (NMR) spectroscopy, Fourier transform infrared (FTIR) spectroscopy, and elemental analysis. The ring‐opening polymerization reaction of BS‐m monomer was studied by FTIR, ¹³C solid‐state NMR, and differential scanning calorimetry. With the polymerization reaction proceeding, the intensities of the FTIR absorption peaks of CH₂, C? O? C, and C? N? C of the oxazine ring decreased gradually, and some of these absorption peaks disappeared. The shapes and intensities of the absorption peaks associated with benzene ring, sulfone group, and aromatic C? S bond changed in various ways. The changes in the solid‐state ¹³C‐NMR pattern, including chemical shifts, intensity of resonances, and line‐width, were observed from the spectra of BS‐m and the corresponding polybenzoxazine. The melting process of BS‐m overlapped with the beginning of the ring‐opening polymerization reaction. The polymerization kinetic parameters were evaluated for nonisothermal and isothermal polymerization of BS‐m. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Synthesis,characterization, and curing behavior of carborane‐containing benzoxazine resins with excellent thermal and thermo‐oxidative stability

Two benzoxazine precursors bearing carborane moiety ( 1 and 2 ) were designed and synthesized successfully by the Mannich reaction of corresponding carborane bisphenol ( 3 and 4 ) with aniline and formaldehyde in 1,4‐dioxane. The obtained precursors were characterized by using multiple spectroscopic techniques including GPC, FTIR, ¹H NMR, ¹³C NMR, and ¹¹B NMR. Nonisothermal DSC studies showed that precursor 1 owned lower apparent activation energies (E_a) than 2 . The optimum curing processes of benzoxazine precursors were also obtained on the basis of DSC data. TGA analyses manifested that the incorporation of carborane moiety endowed the obtained benzoxazine resins (cured 1 and 2 ) with excellent thermal stability and unique thermo‐oxidative stability. The T_d data showed that the initial degradation of both cured 1 and 2 under nitrogen and air was postponed to some extent owing to the shielding effect of carborane moiety on adjacent organic fragments. At higher temperature three‐dimensional polymer networks with B‐O‐B and B–C linkages were formed as chars by the reaction of carborane cage with atmospheric moisture, degradation products such as phenolic hydroxyl, and oxygen (under air). Under nitrogen this network hindered the motion of radicals formed at elevated temperature and thus inhibited further polymer degradation processes. While under air, the formed boron‐rich networks could hardly be further oxidized into carbon dioxide so that the carborane‐containing benzoxazine resins also showed very high char yields. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43488.     

Preparation and properties of bisphenol A‐based bis‐phthalonitrile composite laminates

A series of bisphenol A (BPA)‐based 2,2‐bis‐[4‐(3,4‐dicyanophenoxy)phenyl]propane (BAPh) prepolymers and polymers were prepared using BPA as a novel curing agent. Ultraviolet–visible and Fourier transform infrared spectroscopy spectrum were used to study the polymerization reaction mechanism of the BAPh/BPA polymers. The curing behaviors were studied by differential scanning calorimetry and dynamic rheological analysis, the results indicated that the BAPh/BPA prepolymers exhibit large processing windows (109.5–148.5°C) and low complex viscosity (0.1–1 Pa·s) at moderate temperature, respectively. Additionally, the BAPh/BPA/glass fiber (GF) composite laminates were manufactured and investigated. The flexural strength and modulus of the composite laminates are 548.7–632.8 MPa and 25.7–33.2 GPa, respectively. The thermal stabilities of BAPh/BPA/GF composite laminates were studied by thermogravimetry analysis. The temperatures at 5% weight loss (T_5%) of the composite laminates are 508.5–528.7°C in nitrogen and 508.1–543.2°C in air. In conclusion, the BAPh/BPA systems can be used as superior matrix materials for numerous advanced composite applications. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Trehalose‐based thermosetting resins. I. Synthesis and thermal properties of trehalose vinylbenzyl ether

Trehalose vinylbenzyl ether was synthesized from trehalose and p‐chloromethylstyrene (CMS) in DMSO in the presence of powdered NaOH. The structure of the product was characterized by IR and ¹H NMR spectroscopy. Degree of substitution (DS) on a trehalose unit calculated from the ¹H NMR spectrum varied from 2.4 to 3.2 by changing the feed ratio of p‐chloromethylstyrene to trehalose. Thermal properties of the resin were analyzed by differential scanning calorimetry (DSC). DSC analysis revealed that the resin DS 2.4 has one exothermal peak at 132°C, whereas the resins DS 2.8 and 3.0 have two exothermal peaks. Furthermore, the resin DS 3.2 was found to have only one exothermal peak at 191°C. Dynamic mechanical analysis (DMA) and thermomechanical analysis (TMA) revealed that the cured resin has one transition, implying a glass transition. Biodegradability was assayed by the BOD method, and several percent of the cured resin was found to be degraded with activated sludge for 50 days. Further degradation, however, was not observed. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 46–51, 2004